400-015 TAG Ring Backshell 40 ® with Strain Relief Self-Locking Rotatable Coupling - Straight Only CONNECTOR DESIGNATORS 400 F S 015 M 16 06 L 6 Length: S only (1/2 inch increments: e.g. 6 = 3 inches) Product Series A-F-H-L-S Connector Designator SELF-LOCKING ROTATABLE COUPLING Angle and Profile S = Straight Cable Entry (Table IV, V) Basic Part No. Shell Size (Table I) Strain Relief Style (F, G, L) Finish (Table II) Length ± .060 (1.52) Minimum Order Length 2.0 Inch (See Note 4) Length * A Thread (Table I) Ground Spring * Length ± .060 (1.52) Minimum Order Length 1.5 Inch (See Note 4) E Typ. (Table I) AntiRotation Device STYLE 2 (STRAIGHT See Note 1) STYLE F Light Duty (Table V) .416 (10.5) Approx. Cable Range © 2005 Glenair, Inc. L STYLE G Light Duty (Table IV) STYLE L Light Duty (Table V) .072 (1.8) Approx. Cable Entry Shown with Style G Nut K CAGE Code 06324 .850 (21.6) Approx. Cable Range L Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] Series 40 - Page 16 400-015 TAG Ring Backshell 40 ® with Strain Relief Self-Locking Rotatable Coupling - Straight Only See inside back cover fold-out or pages 13 and 14 for Tables I and II. Dash No. 02 03 04 05 06 07 08 09 10 Dash No. 02 03 04 05 06 07 08 09 10 TABLE IV: CABLE ENTRY K Cable Entry Max Max .545 (13.8) .250 (6.4) .670 (17.0) .375 (9.5) .795 (20.2) .500 (12.7) .920 (23.4) .625 (15.9) 1.045 (26.5) .750 (19.1) 1.170 (29.7) .875 (22.2) 1.295 (32.9) 1.000 (25.4) 1.420 (36.1) 1.125 (28.6) 1.670 (42.4) 1.250 (31.8) TABLE V: CABLE ENTRY L Cable Max Min .968 (24.6) .125 (3.2) 1.046 (26.6) .250 (6.4) 1.156 (29.4) .250 (6.4) 1.218 (30.9) .375 (9.5) 1.343 (34.1) .500 (12.7) 1.468 (37.3) .625 (15.9) 1.593 (40.5) .625 (15.9) 1.718 (43.6) .750 (19.1) 1.843 (46.8) .875 (22.2) Range Max .250 (6.4) .375 (9.5) .500 (12.7) .625 (15.9) .750 (19.1) .875 (22.2) 1.000 (25.4) 1.125 (28.6) 1.250 (31.8) 1. When maximum cable entry (page 21) is exceeded, Style 2 will be supplied. Please consult factory. 2. Metric dimensions (mm) are indicated in parentheses. 3. Cable range is defined as the accommodations range for the wire bundle or cable. Dimensions shown are not intended for inspection criteria. 4. Consult factory for shorter lengths on straight backshells. © 2005 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] Series 40 - Page 17