42 420-001 Sealtite™/Liquidtite Conduit Backshell Rotatable Coupling - Low Profile CONNECTOR DESIGNATORS A-F-H-L-S ROTATABLE COUPLING 420 F S 001 M 16 03-6 Product Series Length: S only (1/2 inch increments: e.g. 6 = 3 inches) Connector Designator Cable Entry (Table IV) Angle and Profile A = 90° B = 45° S = Straight Shell Size (Table I) Finish (Table II) Basic Part No. Length * Length ± .060 (1.52) Minimum Order Length 3.0 Inch A Thread (Table I) (See Note 4) O-Ring C Typ. (Table I) .88 (22.4) Max K ** * Length ± .060 (1.52) Minimum Order Length 2.5 Inch (See Note 4) STYLE 2 (STRAIGHT) Sealtite/Liquidtite Conduit or Equivalent (Customer Furnished) E L ** M ** N Wrench Flat (Table IV) ** (Table IV) G (Table III) (Table III) F (Table III) STYLE 2 (45° & 90°) © 2005 Glenair, Inc. H (Table III) CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] Series 42 - Page 2 42 420-001 Sealtite™/Liquidtite Conduit Backshell Rotatable Coupling - Low Profile See inside back cover fold-out or pages 13 and 14 for Tables I and II. TABLE III: ELBOW DIMENSIONS Shell Size Conn. Desig. H A-F-L-S 09 08 11 10 13 12 15 14 17 16 19 18 21 20 23 22 25 24 28 32 36 E Max .457 (11.6) .520 (13.2) .582 (14.8) .645 (16.4) .738 (18.7) .926 (23.5) .926 (23.5) 1.020 (25.9) 1.020 (25.9) 1.145 (29.1) 1.207 (30.7) 1.238 (31.4) F Max 1.810 (46.0) 1.870 (47.5) 1.930 (49.0) 2.020 (51.3) 2.130 (54.1) 2.320 (58.9) 2.320 (58.9) 2.470 (62.7) 2.470 (62.7) 2.520 (64.0) 2.620 (66.5) 2.710 (68.8) G Max .500 (12.7) .595 (15.1) .610 (15.5) .700 (17.8) .885 (22.5) .975 (24.8) .975 (24.8) 1.125 (28.6) 1.125 (28.6) 1.225 (31.1) 1.575 (40.0) 1.775 (45.1) TABLE IV: CABLE ENTRY Dash Conduit K Dimension (Ref) L Dimension (Ref) No. Size (Ref.) Min Max Max Min 01 3/8 .484 (12.3) .710 (18.0) .504 (12.8) .690 (17.5) 02 1/2 .622 (15.8) .840 (21.3) .642 (16.3) .820 (20.8) 03 3/4 .820 (20.8) .840 (21.3) 1.030 (26.2) 1.050 (26.7) 04 1 1.041 (26.4) 1.066 (27.1) 1.290 (32.8) 1.315 (33.4) 05 1 1/4 1.380 (35.1) 1.410 (35.8) 1.630 (41.4) 1.660 (42.2) 06 1 1/2 1.575 (40.0) 1.600 (40.6) 1.875 (47.6) 1.900 (48.3) 07 2 2.020 (51.3) 2.045 (51.9) 2.350 (59.7) 2.375 (60.3) H Max 1.820 (46.2) 1.940 (49.3) 1.960 (49.8) 2.030 (51.6) 2.120 (53.8) 2.290 (58.2) 2.290 (58.2) 2.400 (61.0) 2.400 (61.0) 2.570 (65.3) 2.820 (71.6) 2.820 (71.6) N Max M Wrench Flats Max 1.155 (29.3) 1.000 (25.4) 1.282 (32.6) 1.125 (28.6) 1.531 (38.9) 1.375 (34.9) 1.781 (45.2) 1.625 (41.3) 2.218 (56.3) 2.062 (52.4) 2.468 (62.7) 2.312 (58.7) 3.031 (77.0) 2.875 (73.0) 1. When maximum cable entry (page 21) is exceeded, Style 2 will be supplied. Dimensions E, F, G and H will not apply. Please consult factory. 2. Metric dimensions (mm) are indicated in parentheses. 3. Cable range is defined as the accommodations range for the wire bundle or cable. Dimensions shown are not intended for inspection criteria. 4. Consult factory for shorter lengths on straight backshells. 5. O-Ring not supplied with Connector Designator A. 6. Sealtite is a trademark of Anaconda Corp. © 2005 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] Series 42 - Page 3