VO3062, VO3063 Vishay Semiconductors Phototriac, Zero Crossing, 1.5 kV/µs dV/dt, 600 V FEATURES • 1500 V/µs dV/dt minimum A 1 6 MT2 C 2 5 NC • 600 V blocking voltage • 100 mA on-state current NC 3 i179030 ZCC* 4 MT1 *Zero crossing circuit • Zero crossing detector • Low input trigger current • 6 pin DIP package • Lead (Pb)-free component • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC APPLICATIONS • Household appliances DESCRIPTION • Triac drive/AC motor drives The VO3062/3063 triac driver family consists of a GaAs infrared LED optically coupled to a monolithic photosensitive zero crossing triac detector chip. The 600 V blocking voltage permits control of off-line voltages up to 240 VAC, with a safety factor of more than two, and is sufficient for as much as 380 V. • Solenoid/valve controls • Office automation equipment/machine • Temperature (HVAC)/lighting controls • Switching power supply AGENCY APPROVALS • UL1577, file no. E52744 system code U/J • CUL - file no. E52744, equivalent to CSA bulletin 5A • DIN EN 60747-5-5 (VDE 0884) available with option 1 • BSI IEC 60950 ORDER INFORMATION PART REMARKS VO3063 DIP-6, ZC, 600 V, Ift = 5 mA VO3062 DIP-6, ZC, 600 V, Ift = 10 mA VO3063-X006 DIP-6 400 mil, ZC, 600 V, Ift = 5 mA VO3062-X006 DIP-6 400 mil, ZC, 600 V, Ift = 10 mA VO3063-X007T SMD-6, ZC, 600 V, Ift = 5 mA VO3062-X007T SMD-6, ZC, 600 V, Ift = 10 mA Note For additional information on the available options refer to option information. ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION PART SYMBOL VALUE UNIT INPUT Reverse voltage VR 6 V Forward current - continuous IF 60 mA Pdiss 100 mW VDRM 600 V ITSM 1 A Pdiss 200 mW IT(RMS) 100 mA Power dissipation OUTPUT Off state output terminal voltage Peak repetitive surge current Power dissipation On-state RMS current Document Number: 83748 Rev. 1.6, 23-Oct-08 VO3062/3063 PW = 100 ms, 120 pps For technical questions, contact: [email protected] www.vishay.com 927 VO3062, VO3063 Phototriac, Zero Crossing, 1.5 kV/µs dV/dt, 600 V Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION PART SYMBOL VALUE UNIT COUPLER Isolation test voltage VISO 5300 VRMS Total power dissipation t=1s Ptot 300 mW Operating temperature range Tamb - 40 to + 100 °C Storage temperature range Tstg - 55 to + 150 °C Tsld 260 °C maximum ≤ 10 s Soldering temperature Note Tamb = 25 °C, unless otherwise specified. Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. 120 Load Current (mA) 100 80 IF = 10 mA 60 40 20 0 - 40 - 20 21353 0 20 40 60 80 100 Temperature (°C) Fig. 1 - On-State Current (RMS) vs. Temperature Note The allowable load current was calculated out under a given operating conditions and only for reference: LED power: QE = 0.015 W, RBA (2-layer) = 72 °C/W THERMAL CHARACTERISTICS SYMBOL VALUE UNIT Maximum LED junction temperature PARAMETER TEST CONDITION Tjmax 125 °C Maximum output die junction temperature Tjmax 125 °C Thermal resistance, junction emitter to board θJEB 150 °C/W Thermal resistance, junction emitter to case θJEC 139 °C/W Thermal resistance, junction detector to board θJDB 78 °C/W Thermal resistance, junction detector to case θJDC 103 °C/W Thermal resistance, junction emitter to junction detector θJED 496 °C/W Thermal resistance, case to ambient θCA 3563 °C/W Note The thermal model is represented in the thermal network below. Each resistance value given in this model can be used to calculate the temperatures at each node for a given operating condition. The thermal resistance from board to ambient will be dependent on the type of PCB, layout and thickness of copper traces. For a detailed explanation of the thermal model, please reference Vishay's Thermal Characteristics of Optocouplers Application note. www.vishay.com 928 For technical questions, contact: [email protected] Document Number: 83748 Rev. 1.6, 23-Oct-08 VO3062, VO3063 Phototriac, Zero Crossing, 1.5 kV/µs dV/dt, 600 V Vishay Semiconductors TA θCA Package TC θEC θDC θDE TJD TJE θDB θEB TB θBA 19996 TA ELECTRICAL CHARACTERISTCS PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT 10 µA 1.2 1.5 V 10 500 INPUT Reverse current VR = 6 V IR Forward voltage IF = 30 mA VF OUTPUT Leakage with LED off, either direction Critical rate of rise off-state voltage VDRM = 600 V IDRM VD = 400 V dV/dt 1500 2000 nA V/µs COUPLER LED trigger current, current required to latch output VO3063 IFT 5 mA VO3062 IFT 10 mA 3 V ITM = 100 mA Peak, IF = Rated IFT Peak on-state voltage, either direction Holding current, either direction Inhibit voltage (MT1-MT2 voltage above which device will not trigger) IF = 10 mA maximum, at rated VDRM, off state Leakage in inhibited state VTM 1.7 IH 200 VINH 12 22 V VDRM2 250 1000 µA µA Note Tamb = 25 °C, unless otherwise specified. Minimum and maximum values were tested requierements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION Climatic classification Pollution degree Maximum working insulation voltage MIN. TYP. IEC 68 part 1 40/85/21 DIN VDE 0109 2 Comparative tracking index per DIN IEC 112/VDE 0303 part 1, group IIIa per DIN VDE 6110 175 399 Highest allowable overvoltage SYMBOL CTI 175 Transient overvoltage VIOTM 8000 Recurring peak voltage VIORM 890 MAX. UNIT Vpeak Vpeak Insulation resistance at 25 °C VIO = 500 V RIS ≥ Insulation resistance at TS VIO = 500 V RIS ≥ 109 Ω Insulation resistance at 100 °C VIO = 500 V RIS ≥ 1011 Ω Document Number: 83748 Rev. 1.6, 23-Oct-08 For technical questions, contact: [email protected] 1012 Ω www.vishay.com 929 VO3062, VO3063 Phototriac, Zero Crossing, 1.5 kV/µs dV/dt, 600 V Vishay Semiconductors SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL Partial discharge test voltage Method a, Vpd = VIORM x 1.875 Safety limiting values maximum values allowed in the event of a failure MIN. TYP. MAX. UNIT Vpd 1325 Vpeak Safety power rating PSO 400 mW Safety current rating ISI 150 mA Safety temperature rating TSI 165 °C Minimum external air gap (clearance) Measured from input terminals to output terminals, shortest distance through air ≥7 mm Minimum external tracking (creepage) Measured from input terminals to output terminals, shortest distance path along body ≥7 mm Note As per IEC 60747-5-2, 7.4.3.8.1, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of prodective circuits. TYPICAL CHARACTERISTICS Tamb = 25 °C, unless otherwise specified 100 On-State Current ITM (mA) VF - Forward Voltage (V) 1.4 1.3 Ta = - 40 °C 1.2 Ta = 25 °C 1.1 Ta = 85 °C 1.0 0.9 1 10 60 40 20 0 - 20 - 40 - 60 - 80 - 100 - 2 - 1.5 - 1 - 0.5 0.8 19620 80 100 19605 IF - Forward Current (mA) 0 0.5 1 1.5 2 On-State Voltage VTM (V) Fig. 2 - Forward Voltage vs. Forward Current Fig. 4 - On-State Current vs. VTM 1000 1.4 Trigger Current 1.2 Ilkg (nA) 100 10 1.0 0.8 0.6 0.4 0.2 1 - 40 - 20 19619 0 0 20 40 60 80 100 Temperature (°C) Fig. 3 - Off-State Leakage Current vs. Temperature www.vishay.com 930 - 40 19621 10 60 110 Temperature (°C) Fig. 5 - Normalized Trigger Current vs. Temperature For technical questions, contact: [email protected] Document Number: 83748 Rev. 1.6, 23-Oct-08 VO3062, VO3063 Phototriac, Zero Crossing, 1.5 kV/µs dV/dt, 600 V 15 Turn-on Time (µs) Turn-on Time (µs) 100 10 12 9 6 3 1 5 19618 8 11 14 17 0 - 40 20 19602 LED Current (mA) Fig. 6 - Turn-on Time vs. LED Current - 20 0 20 40 60 80 100 Temperature (°C) Fig. 8 - Turn-on Time vs. Temperature 2.0 5.0 1.8 4.5 1.6 4.0 1.4 IFT (mA) Holding Current Vishay Semiconductors 1.2 1.0 3.5 3.0 0.8 2.5 0.6 0.4 - 40 - 20 2.0 0 20 40 60 80 100 20 Temperature (°C) 19608 19609 Fig. 7 - Normalized Holding Current vs. Temperature 40 60 80 100 Pulse Width (µs) Fig. 9 - Trigger Current vs. Pulse Width PACKAGE DIMENSIONS in inches (millimeters) Option 6 Pin one ID 3 2 1 4 5 6 0.407 (10.36) 0.391 (9.96) 0.307 (7.8) 0.291 (7.4) 0.248 (6.30) 0.256 (6.50) ISO method A 0.335 (8.50) 20° 0.343 (8.70) 0.039 (1.00 ) min . typ . 0.130 (3.30) 0.150 (3.81) Option 7 4° typ . 18° 0.033 (0.84) typ. 0.018 (0.46) 0.020 (0.51) i178014_1 0.014 (0.35) 0.010 (0.25) 0.400 (10.16) 0.430 (10.92) 0.300 (7.62) 0.048 (1.22) 0.052 (1.32) 0.033 (0.84) typ. 0.100 (2.54) typ. 3° - 9° 0.008 (0.20) 0.012 (0.30) 0.300 (7.62) TYP. 0.130 (3.30) 0.150 (3.81) 0.028 (0.7) 0.180 (4.6) 0.160 (4.1) 0.300 to 0.347 (7.62 to 8.81) 0.315 (8.0) min.. 0.331 (8.4) min. 0.406 (10.3) max. Document Number: 83748 Rev. 1.6, 23-Oct-08 For technical questions, contact: [email protected] www.vishay.com 931 VO3062, VO3063 Vishay Semiconductors Phototriac, Zero Crossing, 1.5 kV/µs dV/dt, 600 V OZONE DEPLETING SUBSTANCES POLICY STATEMENT It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively. 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany www.vishay.com 932 For technical questions, contact: [email protected] Document Number: 83748 Rev. 1.6, 23-Oct-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1