VOM1271 www.vishay.com Vishay Semiconductors Photovoltaic MOSFET Driver with Integrated Fast Turn-Off, Solid-State Relay FEATURES • Open circuit voltage at IF = 10 mA, 8.4 V typical 1 • Short circuit current at IF = 10 mA, 15 μA typical 4 • Isolation test voltage 4500 VRMS • Logic compatible input Turn Off 2 • High reliability • Integrated rapid turn-off circuitry 3 • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 i179066_6 APPLICATIONS • High-side driver DESCRIPTION • Solid-state relays The VOM1271 is a stand-alone optically isolated MOSFET driver. Unlike conventional MOSFET drivers, which require an external power supply to provide VCC and or VDD rails to the driver itself, the VOM1271 obtains all the required current to drive its internal circuitry from the LED current on the low voltage primary side of the isolation barrier. This saves the designer the space and cost associated with providing one or more external power supplies. The VOM1271 also integrates a turn-off circuit internal to the component itself, thus doing away with the need for additional components in order to increase the overall switching speed by decreasing the turn-off time. These features, combined with a small SOP4 package, provide designers with a small footprint, highly integrated isolated gate driver solution for a large variety of MOSFET drive applications. • Floating power supply • Power control • Data acquisition • ATE • Isolated solenoid drivers • Isolated high current relay drivers • Isolated high voltage relay drivers AGENCY APPROVALS • UL1577 • cUL, equivalent to CSA bulletin 5A • FIMKO EN 60950-1 SAFETY AGENCY COMPLIANCE Please see document: www.vishay.com/doc?83743 ORDERING INFORMATION V O M 1 PART NUMBER PACKAGE SOP-4 2 7 1 T TAPE AND REEL SOP-4 7.21 mm UL, cUL, FIMKO VOM1271T Note • For additional information on the available options refer to option information. The product is available only on tape and reel. Rev. 1.3, 29-Aug-12 Document Number: 83469 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOM1271 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT IF 50 mA IR ≤ 10 μA VR 5 V Tamb - 40 to + 100 °C SSR LED input ratings continous forward current LED input ratings reverse voltage Ambient operating temperature range Storage temperature range Tstg - 40 to + 125 °C Pin soldering temperature (1) t ≤ 10 s max. Tsld 260 °C Isolation test voltage between emitter and detector t=1s VISO 4500 VRMS Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SOP). ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT IF = 10 mA VF 1.2 1.4 1.6 V IF = 5 mA VOC IF = 10 mA VOC IF = 20 mA IF = 30 mA LED forward voltage Open circuit voltage Short circuit current 8.1 V 8.4 V VOC 8.7 V VOC 8.9 V IF = 5 mA ISC 7.0 μA IF = 10 mA ISC 15.0 μA IF = 20 mA ISC 30.0 μA IF = 30 mA ISC 47.0 μA 7.8 6.0 Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Turn-on time Turn-off time TEST CONDITION SYMBOL CL = 200 pF, IF = 20 mA, PW = 2 ms, duty cycle = 50 % ton MIN. TYP. 53 MAX. UNIT μs toff 24 μs 2 ms VOM1271T 1 4 Input 200 pF Turn OFF IF 10 MΩ VOC, ISC ton toff Output 2 3 90 % 10 % Fig. 1 - ton, toff Test Circuit and Waveforms Rev. 1.3, 29-Aug-12 Document Number: 83469 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOM1271 www.vishay.com Vishay Semiconductors SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION Climatic classification (according to IEC 68 part 1) Comparative tracking index SYMBOL MIN. TYP. IEC 68 part 1 Insulation group IIIa MAX. UNIT 40/100/21 CTI 175 399 Transient overvoltage VIOTM 6000 V Recurring peak voltage VIORM 630 V Package safety power PSO 350 mW Package safety current ISI 150 mA Package safety temperature TSI 175 °C Creepage distance 5 mm Clearance distance 5 mm TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 12 10 RL = 1 MΩ 9 11 10 7 6 VOC (V) VOC vs. IF (V) 8 RL = 500 kΩ 5 4 3 9 10 mA 8 30 mA 7 6 2 5 mA 5 1 0 4 0 5 10 15 20 25 30 35 40 45 50 - 40 - 20 IF (mA) 0 20 40 60 80 100 Ambient Temperature (°C) Fig. 2 - Output Open Circuit Voltage vs. LED Current Fig. 4 - Output Open Circuit Voltage vs. Ambient Temperature 60 600 50 500 30 mA ton, toff (μs) ISC (μA) 40 30 20 10 mA 400 300 200 ton 10 100 toff 5 mA 0 0 - 40 - 20 0 20 40 60 80 100 Ambient Temperature (°C) Fig. 3 - Output Short-Circuit Current vs. Ambient Temperature Rev. 1.3, 29-Aug-12 0 5 10 15 20 25 30 35 40 45 50 IF (mA) Fig. 5 - ton, toff vs. LED Current Document Number: 83469 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOM1271 www.vishay.com Vishay Semiconductors ISC - Short Circuit Output Current (μA) 2.0 1.8 1.6 IR (μA) 1.4 1.2 1.0 0.8 0 °C 0.6 0.4 0.2 100 °C 0 21 20 22 23 24 25 VR (V) 80 70 45 mA 60 35 mA 50 25 mA 40 30 15 mA 20 5 mA 10 0 0 1 2 3 4 5 6 7 8 9 10 VOC - Open Circuit Output Voltage (V) Fig. 6 - LED Reverse Current vs. Reverse Voltage Fig. 8 - Short Circuit Output Current vs. Open Circuit Output Voltage 1.6 0 °C 1.5 25 °C VF (V) 1.4 1.3 100 °C 1.2 1.1 1.0 0 5 10 15 20 25 30 35 40 45 50 IF (mA) Fig. 7 - LED Forward Voltage vs. LED Forward Current APPLICATION DESCRIPTION Figure 8 illustrates a standard isolated MOSFET driver such as Vishay’s VO1263. Though these parts are generally capable of supplying higher output current, they lack integrated fast turn-off circuitry. Thus, if high turn-off speed is required. external circuitry needs to be provided, as illustrated in figure one. Channel 1 control – Figure 9 illustrates the ability to do away with external turn-off circuitry with the VOM1271, by taking advantage of the VOM1271’s integrated turn-off circuitry. P-channel JFET + Switch 1 N-channel MOSFETs 2 MΩ Fig. 9 - Typical MOSFET Driver Application without Integrated Fast Turn-Off Rev. 1.3, 29-Aug-12 Document Number: 83469 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOM1271 www.vishay.com VOM1271 Vishay Semiconductors VOM1271 4 1 TURN OFF 2 4 1 + + TURN OFF - 2 3 Single MOSFET Driver Application - 3 Bidirectional MOSFET Driver Application Fig. 10 - Typical Bidirectional MOSFET Driver Application with Integrated Fast Turn-Off PACKAGE DIMENSIONS in millimeters PACKAGE MARKING (example) M1271 V YWW 68 Pin One Dimple Rev. 1.3, 29-Aug-12 Document Number: 83469 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOM1271 www.vishay.com Vishay Semiconductors TAPE AND REEL PACKAGING Dimensions in millimeters 1.50 ± 0.1 2.00 ± 0.05 ESD sticker 4.00 ± 0.1 1.75 ± 0.1 Tape slot in core 5.50 ± 0.05 330 (13") 7.33 ± 0.1 2 1 3 4 + 0.3 12.00 - 0.1 Regular, special or bar code label 17999 8° 2.66 ± 0.1 1.50 ± 0.25 8.00 ± 0.1 4.72 ± 0.1 22646 Fig. 11 - Tape and Reel Shipping Medium (EIA-481, revision A, and IEC 60286), 2000 units per reel Rev. 1.3, 29-Aug-12 Fig. 12 - Tape Dimensions Document Number: 83469 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000