WINCHESTER 78

REV
DESCRIPTION
05
REVISED DRAWING
PER ER30231
BY
APPD
DATE
XXX
2. MATERIAL SPECIFICATIONS:
CONTACTS AND TRI-LOC BODY: COPPER ALLOY
ALIGNMENT PINS: BRASS PER ASTM B16
CRIMP SLEEVE: PHOS. BRONZE
O-RINGS AND STRAIN RELIEF: SILICONE RUBBER
ALL PLASTIC PARTS: 20% GLASS FILLED POLYPROPYLENE
ALL OTHER METAL PARTS: 303 STAINLESS STEEL PER ASTM A582
6. OPTICAL:
WAVELENGTH: 1100nm - 1350nm
INSERTION LOSS: 0.3dB TYPICAL, 0.5dB MAX
RETURN LOSS: > -45dB, -50dB TYPICAL
KFC
01/07/10
NOTES: UNLESS OTHERWISE SPECIFIED
1. INTERFACE COMPLIANT TO SMPTE 304 SPECIFICATION.
7. REPLACEMENT KITS:
CONTACT KIT: 7760-000-00708Z
CONTACT KIT WITH CARTRIDGE: 7760-000-00710Z
8. CABLE PREPARATION AND STRIPPING PROCEDURE: CAP-E05.
3. FINISH SPECIFICATIONS:
STAINLESS STEEL PARTS: PASSIVATE
TRI-LOC BODY: .000100 MIN NICKEL PER AMS-QQ-N-290
OVER COPPER FLASH PER ASTM B734 (RoHS)
CONTACTS: .000100 MIN GOLD PER ASTM B488 OVER
.000080 MIN NICKEL PER AMS-QQN-290 (RoHS)
CRIMP SLEEVE: .000100 MIN NICKEL PER AMS-QQ-N-290 OVER
COPPER FLASH PER ASTM B734 (RoHS)
9. OPTIONAL ENVIRONMENTAL BOOT 7760-000-00704Z SOLD SEPARATELY.
10. RED LDPE DUST CAP INCLUDED (NOT SHOWN)
11. CRIMP TOOLING:
FOR FACTORY APPLICATION USE HAND TOOL KTH-1000 AND DIE KTH-2035
FOR FIELD APPLICATION USE HAND TOOL KTH-5000 AND DIE KTH-5018
4. ELECTRICAL SPECIFICATIONS:
LOW VOLTAGE CONTACTS: 42 - 60 VAC, 1 AMP
AUX ELECTRICAL CONTACTS: 600 VAC, 10 AMP
5. ENVIRONMENTAL:
OPERATING TEMPERATURE RATING: -40°C TO 75°C
NON-OPERATING/STORAGE TEMPERTURE RATING: -40°C TO 85°C
HUMIDITY: <95 RH (AT 40°C)
.915 23.24
5.051 128.30
.804 20.42
MARK: 7765-4-3 (DATE CODE)
3/4" WRENCH FLATS (180° APART)
CATALOG P/N: 7765-4-3
9/16" WRENCH FLATS (180° APART)
PER ASME Y14.5M-1994
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
DECIMAL: .XX [X.X] ± .01 [0.3]
.XXX [X.XX] ± .005 [0.13]
.XXXX [X.XXX] ± .XXXX
ANGLES: ± 2°
SCALE: 1:1
THIRD
ANGLE
Winchester Electronics Corporation
62 Barnes Industrial Road North
Wallingford, Connecticut 06492
CUSTOMER
SALES DRAWING
DRAWN
PSM
APPROVED
XXX
DMF026 B
DATE APPROVED
04/06/10 WPM
DATE APPROVED
XX/XX/XX XXX
DATE
04/07/10
DATE
XX/XX/XX
TRI-LOC, SMPTE 304, PLUG
PRE-POLISHED
A
SD7765-4-3
SHT
OF
1
2 05
REV
2
1
11
05
REVISED DRAWING
PER ER30231
BY APPD
DATE
XXX
7
DESCRIPTION
KFC
01/07/11
REPLACEMENT COMPONENT ORDERING NUMBERS
REV
9
6
3
10
5
4
8
12
13
14
14
13
12
11
10
9
8
VNFPS01-900-34
VNSC-3-4U
7760-000-00711Z
78-0705U
78-1012U
78-3013U
78-3012U
7
6
5
4
3
2
1
ITEM NO.
SPLICE PROTECTOR SLEEVE, 34MM
RED LDPE DUST CAP, .750" ID
FIBER OPTIC CONNECTOR STUB
REAR O-RING
STRENGTH MEMBER SUPPORT CLAMP
PLUG INSULATOR HALF SIDE "A"
PLGU INSULATOR HALF SIDE "B"
50
25
2
25
10
25
25
78-0102U
#4-40 HEX SET SCREW
10
1-8156U
78-4006U
78-4005U
78-7003U
78-0301U
78-0701U
CRIMP SLEEVE (CABLE SHIELD FERRULE)
PLUG FEMALE CRIMP CONTACT
PLUG MALE CRIMP CONTACT
PLUG CARTRIDGE ASSEMBLY
WASHER FOR REAR CABLE SEAL
REAR CABLE SEAL
25
50
50
10
25
25
New Ferrule
Design/QTY.
PART NO.
Description
PLATING CODE(S)
DMF026 B
CATALOG P/N: 7765-4-3
PER ASME Y14.5M-1994
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
DECIMAL: .XX [X.X] ± .01 [0.3]
.XXX [X.XX] ± .005 [0.13]
.XXXX [X.XXX] ± .XXXX
ANGLES: ± 2°
SCALE: 1:1
THIRD
ANGLE
Winchester Electronics Corporation
62 Barnes Industrial Road North
Wallingford, Connecticut 06492
CUSTOMER
SALES DRAWING
DRAWN
PSM
APPROVED
XXX
DATE APPROVED
04/06/10 WPM
DATE APPROVED
XX/XX/XX XXX
DATE
04/07/10
DATE
XX/XX/XX
TRI-LOC, SMPTE 304, PLUG
PRE-POLISHED
A
SD7765-4-3
SHT
OF
2
2 05
REV