REV DESCRIPTION BY APPD DATE E REVISED PER ER27962 XXX 2. MATERIAL SPECIFICATIONS: CONTACTS AND TRI-LOC BODY: COPPER ALLOY ALIGNMENT PINS: BRASS PER ASTM B16 CRIMP SLEEVE: PHOS. BRONZE O-RINGS AND STRAIN RELIEF: SILICONE RUBBER ALL PLASTIC PARTS: 20% GLASS FILLED POLYPROPYLENE ALL OTHER METAL PARTS: 303 STAINLESS STEEL PER ASTM A582 6. OPTICAL: WAVELENGTH: 1100nm - 1350nm INSERTION LOSS: 0.3dB TYPICAL, 0.5dB MAX RETURN LOSS: > -45dB, -50dB TYPICAL KFC 01/06/11 NOTES: UNLESS OTHERWISE SPECIFIED 1. INTERFACE COMPLIANT TO SMPTE 304 SPECIFICATION. 7. REPLACEMENT KITS: CONTACT KIT: 7760-000-00701Z CONTACT KIT WITH CARTRIDGE: 7760-000-00703Z 8. CABLE PREPARATION AND STRIPPING PROCEDURE: CAP-E05. 3. FINISH SPECIFICATIONS: STAINLESS STEEL PARTS: PASSIVATE TRI-LOC BODY: .000100 MIN NICKEL PER AMS-QQ-N-290 OVER COPPER FLASH PER ASTM B734 (RoHS) CONTACTS: .000100 MIN GOLD PER ASTM B488 OVER .000080 MIN NICKEL PER AMS-QQN-290 (RoHS) CRIMP SLEEVE: .000100 MIN NICKEL PER AMS-QQ-N-290 OVER COPPER FLASH PER ASTM B734 (RoHS) 9. OPTIONAL ENVIRONMENTAL BOOT 7760-000-00704Z SOLD SEPARATELY. 10. RED LDPE DUST CAP INCLUDED (NOT SHOWN) 11. CRIMP TOOLING: FOR FACTORY APPLICATION USE HAND TOOL KTH-1000 AND DIE KTH-2035 FOR FIELD APPLICATION USE HAND TOOL KTH-5000 AND DIE KTH-5018 4. ELECTRICAL SPECIFICATIONS: LOW VOLTAGE CONTACTS: 42 - 60 VAC, 1 AMP AUX ELECTRICAL CONTACTS: 600 VAC, 10 AMP 5. ENVIRONMENTAL: OPERATING TEMPERATURE RATING: -40°C TO 75°C NON-OPERATING/STORAGE TEMPERTURE RATING: -40°C TO 85°C HUMIDITY: <95 RH (AT 40°C) .915 23.24 5.051 128.30 .804 20.42 MARK PER ES-781: 7765-3-3 (DATE CODE) 3/4" WRENCH FLATS (180° APART) 9/16" WRENCH FLATS (180° APART) CATALOG P/N: 7765-3-3 PER ASME Y14.5M-1994 UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES [MM] TOLERANCES: DECIMAL: .XX [X.X] ± .01 [0.3] .XXX [X.XX] ± .005 [0.13] .XXXX [X.XXX] ± .XXXX ANGLES: ± 2° SCALE: 1:1 THIRD ANGLE Winchester Electronics Corporation 62 Barnes Industrial Road North Wallingford, Connecticut 06492 CUSTOMER SALES DRAWING DRAWN PSM APPROVED WPM DMF026 B DATE APPROVED 03/25/09 RL DATE APPROVED 08/03/09 JCF TRI-LOC, SMPTE 304, PLUG DATE 08/03/09 DATE 01/19/10 A SD7765-3-3 SHT OF 1 2 REV E E REVISED PER ER30231 9 7 12 2 BY APPD DATE XXX 8 DESCRIPTION KFC 01/06/11 REPLACEMENT COMPONENT ORDERING NUMBERS REV 3 11 1 10 5 6 13 4 13 12 11 10 9 VNSC-3-4U 78-0705U 78-1012U 78-3013U 78-3012U RED LDPE DUST CAP, .750" ID REAR O-RING STRENGTH MEMBER SUPPORT CLAMP PLUG INSULATOR HALF SIDE "A" PLUG INSULATOR HALF SIDE "B" 25 25 10 25 25 8 78-0102U #4-40 HEX SET SCREW 10 7 6 5 4 3 2 1 1-8156U 78-4006U 78-4005U 78-7016U 78-7003U 78-0301U 78-0701U CRIMP SLEEVE (CABLE SHIELD FERRULE) PLUG FEMALE CRIMP CONTACT PLUG MALE CRIMP CONTACT TERMINI FOR MANUAL POLISH W/ PROT. CAP PLUG CARTRIDGE ASSEMBLY WASHER FOR REAR CABLE SEAL REAR CABLE SEAL 25 50 50 10 10 25 25 ITEM NO. PART NO. Description QTY. PLATING CODE(S) DMF026 B CATALOG P/N: 7765-3-3 PER ASME Y14.5M-1994 UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES [MM] TOLERANCES: DECIMAL: .XX [X.X] ± .01 [0.3] .XXX [X.XX] ± .005 [0.13] .XXXX [X.XXX] ± .XXXX ANGLES: ± 2° SCALE: 1:1 THIRD ANGLE Winchester Electronics Corporation 62 Barnes Industrial Road North Wallingford, Connecticut 06492 CUSTOMER SALES DRAWING DRAWN PSM APPROVED WPM DATE APPROVED 03/25/09 RL DATE APPROVED 08/03/09 JCF TRI-LOC, SMPTE 304, PLUG DATE 08/03/09 DATE 01/19/10 A SD7765-3-3 SHT OF 2 2 REV E