TA84002F/FG TOSHIBA BIPOLAR LINEAR INTEGRATED CIRCUIT MULTI-CHIP TA84002F/FG PWM CHOPPER-TYPE 2−PHASE BIPOLAR STEPPING MOTOR DRIVER The TA84002F/FG is designed to drive both windings of a two-phase bipolar stepping motor. FEATURES z Internal PWM current control z Wide range of operating supply voltages VM (motor) : 10 V to 30 V VCC (control) : 4.5 V to 5.5 V z Output current : 1.0 A (peak) z Multichip IC consisting of four P-channel MOSFETs and one main chip z Full-step and half-step are available Weight: 0.79 g (typ.) z Internal thermal-shutdown circuit z Package : HSOP20−P−450−1.00 Note 1: This product has a multichip (MCP) structure utilizing Pch MOS technology, which is sensitive to electrostatic discharge. Handle with care. TA84002FG: The TA84002FG is a Pb-free product. The following conditions apply to solderability: *Solderability 1. Use of Sn-37Pb solder bath *solder bath temperature = 230°C *dipping time = 5 seconds *number of times = once *use of R-type flux 2. Use of Sn-3.0Ag-0.5Cu solder bath *solder bath temperature = 245°C *dipping time = 5 seconds *number of times = once *use of R-type flux 1 2006-3-6 TA84002F/FG PIN ASSIGNMENT 2 2006-3-6 TA84002F/FG BLOCK DIAGRAM TRUTH TABLE X: PHASE ENABLE OUT (+) OUT (−) X H OFF OFF H L H L L L L H Don’t care 3 2006-3-6 TA84002F/FG OUTPUT STAGE z The TA84002F/FG is a multichip IC consisting of four P-channel MOSFETs and one main chip. z The four P-channel MOSETs are used as upper-side power transistors. z The output current is controlled by a switching lower-side transistor. z During CHOP ON, the current flows through the P-channel MOS, motor winding, sink transistor and sense resistor. z During CHOP OFF, the current circulates the motor winding, P-channel MOS and the diode of the P-channel MOS. z Power dissipation is divided between the five chips. : (1) CHOP ON (Drive Mode) Q1: ON, Q2: OFF Q3: OFF, Q4: ON : (2) CHOP OFF (Slow Decay) Q1: ON, Q2: OFF Q3: OFF, Q4: OFF : (3) ALL OFF (Fast Decay) 4 2006-3-6 TA84002F/FG PWM CURRENT CONTROL The output current is sensed and controlled independently in each bridge by an external sense resistor (RFN), internal comparator, and mono-stable multi-vibrator. When the bridge is turned ON, the current increases in the motor winding and flows through the external sense resistor until the sense voltage (VNF) reaches the level set at the comparator input: Vref / 5. The comparator then triggers the mono-stable multivibrator, which turns OFF the lower transistor of the bridge. The OFF time is determined by the external RC timing components of the monostable multivibrator: tOFF ≈ 1.1 CR. The approximate value of the current limiting (IO) is given by the following: IO = (Vref / 5) / RNF−0.05. 5 2006-3-6 TA84002F/FG TIMING CHART (1) Full Step 6 2006-3-6 TA84002F/FG (2) Half Step 7 2006-3-6 TA84002F/FG ABSOLUTE MAXIMUM RATINGS (Ta = 25°C) CHARACTERISTIC SYMBOL RATING UNIT Supply Voltage (Motor) VM 35 V Supply Voltage (Control) VCC 7 V Output Current IO 1.0 A / ch Input Voltage VIN GND − 0.4 to VCC + 0.4 V V Power Dissipation PD 2.5 (Note) W Operating Temperature Topr −30 to 85 °C Storage Temperature Tstg −55 to 150 °C Note: This rating is obtained when the product is mounted on a 50 × 50 × 1.6 mm PCB 60% or more of which is occupied by copper. RECOMMENDED OPERATION CONDITION (Ta = −30 to 85°C) SYMBOL TEST CIR− CUIT Supply Voltage (Control) VCC Supply Voltage (Motor) CHARACTERISTIC MIN TYP. MAX UNIT ― 4.5 5.0 5.5 V VM ― 10 24 30 V Output Current IO ― ― ― 0.8 A / ch Input Voltage VIN ― GND ― VCC V Reference Voltage Vref ― 1.2 2.5 VCC − 0.5 V fPWM ― 15 30 50 kHz PWM Frequency TEST CONDITION PHASE, ENABLE 8 2006-3-6 TA84002F/FG ELECTRICAL CHARACTERISTICS (Ta = 25°C, VCC = 5 V, VM = 24 V) CHARACTERISTIC SYMBOL TEST CIR− CUIT TEST CONDITION MIN TYP. MAX 2.0 ― VCC + 0.3 V GND − 0.3 V ― 0.8 PHASE, ENABLE, VIN = 5 V ― 2 20 PHASE, VIN = GND ― 0 1 ENABLE, VIN = GND ― 50 100 VIN(H) Input Voltage 1 PHASE, ENABLE VIN(L) IIN(H) Input Current IIN(L) 2 IIN(L) ICC1 3 ENABLE A / B = Low 2-Phase 100% ON ― 110 180 ICC2 4 ENABLE A / B = Low 2-Phase 100% OFF ― 6 14 ICC3 3 ENABLE A = Low, B = High 1-Phase 100% ON ― 55 90 ICC4 4 ENABLE A = Low, B = High 1-Phase 100% OFF ― 6 14 3 ENABLE A / B = High 2-Phase OFF ― 6 14 ENABLE A / B = Low 2-Phase ON ― 5 13 ENABLE A = Low, B = High 1-Phase ON ― 4.5 11 ENABLE A / B = High 2-Phase OFF ― 4 9 IO = 0.5 A ― 0.35 0.8 IO = 1.0 A ― 0.65 2.0 Supply Current ICC5 IM1 IM2 5 IM3 Output Saturation Voltage (Lower-side) VSAT1 VSAT2 6 UNIT V µA mA V ON Resistor (Upper-side) Ron1 7 IO = 0.5 A ― 0.6 1.0 Ω Diode Forward Voltage (Lower-side) VF(L) 8 IF = 1.0 A ― 1.4 2.0 V Diode Forward Voltage (Upper-side) VF(H) 9 IF = 1.0 A ― 0.95 1.8 V Reference Voltage Range Vref ― 1.0 2.5 VCC − 0.5 V Reference Current Iref 10 Vref = 2.5 V ― 0.2 5 µA GAIN 11 VNF / Vref 0.17 0.2 0.23 Setting Current Iset ― Vref = 2.5 V, RNF = 1 Ω 0.35 0.45 0.55 A Thermal Shutdown Temperature TSD ― Tj ― 165 ― °C ∆T ― ― 15 ― °C ― 0 100 ― 0 50 530 730 Reference Divider Ratio Thermal Shutdown Hysteresis Output Leakage Current Pch MOS Drive Current IL (H) IL (L) IG 12 P-Channel MOS 13 330 9 µA µA 2006-3-6 TA84002F/FG TEST CIRCUIT 1. VIN (H), VIN (L) 2. IIN (H), IIN (L) 10 2006-3-6 TA84002F/FG 3. ICC1, ICC3, ICC5 4. ICC2, ICC4 11 2006-3-6 TA84002F/FG 5. IM1, IM2, IM3 6. VSAT1, VSAT2 12 2006-3-6 TA84002F/FG 7. Ron1 8. VF (L) 13 2006-3-6 TA84002F/FG 9. VF (H) 10. Iref 14 2006-3-6 TA84002F/FG 11. Iset 12. IL (H), IL (L) 15 2006-3-6 TA84002F/FG 13. IG 16 2006-3-6 TA84002F/FG APPLICATION CIRCUIT In case of IOUT = 0.5 A TA84002F/FG Note 1: A capacitor for noise suppression should be connected between the power supply (VCC, VM, Vref) and GND to stabilize operation. Note 2: Utmost care is necessary in the design of the output, VCC, VM, and GND lines since the IC may be destroyed by short-circuiting between outputs, air contamination faults, or faults due to improper grounding, or by short-circuiting between contiguous pins. 17 2006-3-6 TA84002F/FG PACKAGE DIMENSIONS HSOP20−P−450−1.00 Unit: mm Weight: 0.79 g (typ.) 18 2006-3-6 TA84002F/FG Notes on Contents 1. Block Diagrams Some of the functional blocks, circuits, or constants in the block diagram may be omitted or simplified for explanatory purposes. 2. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 3. Timing Charts Timing charts may be simplified for explanatory purposes. 4. Application Circuits The application circuits shown in this document are provided for reference purposes only. Thorough evaluation is required, especially at the mass production design stage. Toshiba does not grant any license to any industrial property rights by providing these examples of application circuits. 5. Test Circuits Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment. IC Usage Considerations Notes on handling of ICs [1] The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. [2] Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. [3] If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. [4] Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. 19 2006-3-6 TA84002F/FG Points to remember on handling of ICs (1) Thermal Shutdown Circuit Thermal shutdown circuits do not necessarily protect ICs under all circumstances. If the thermal shutdown circuits operate against the over temperature, clear the heat generation status immediately. Depending on the method of use and usage conditions, such as exceeding absolute maximum ratings can cause the thermal shutdown circuit to not operate properly or IC breakdown before operation. (2) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (TJ) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. (3) Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor’s power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device’s motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 20 2006-3-6 TA84002F/FG 21 2006-3-6