FPF2024/5/6/7 Full Functional Load Switch With 100mA Current Limit Features General Description 1.6V to 5.5V Input Voltage Range The FPF2024/5/6/7 are low RDS(ON) P-Channel MOSFET load switches with 150mA typical current limit value targeting small package load switch applications. The extended input voltage range spans from 1.6V to 5.5V to fulfill today's Ultra Portable Device's supply requirements. Switch control is by a logic input (ON) capable of interfacing directly with a low voltage control signal. Ultra Low Average Quiescent Current 1µA typ @1.8V Typical RDS(ON) = 225mΩ @ VIN = 3.3V Typical RDS(ON) = 280mΩ @ VIN = 1.8V 100mA Fixed Current Limit Minimum Under Voltage Lockout CMOS and Open Drain Fault Flag Options The FPF2024/5/6/7 respond to an output overload condition by going into constant current mode where the output current is regulated by the load switch. If the overcurrent condition persists beyond the 10ms Blanking Time, FPF2024 and FPF2025 pull the fault signal pin (FLAGB) low and shut-off the switch. An Auto-Restart feature turns FPF2024 and FPF2025 on again after 70ms if the ON pin is still active. The FPF2026 has a Latch-Off feature which shuts off the switch off after the expiration of the 10ms Blanking Time and keeps it off until the ON pin is toggled. The FPF2027 responds to an overload condition by immediately pulling the fault signal pin low and the switch remains in constant current mode until the output overload condition is removed. FPF2027 has a Startup Blanking feature which prevents startup transient overcurrent conditions from triggering the fault signal pin for 10ms after initial turn on via the ON pin. Fault Blanking Auto Restart Thermal Shutdown ESD Protection above 5500V HBM and 1500V CDM Applications PDAs Cell Phones GPS Devices Digital Cameras Peripheral Ports MP3 Players These parts are available in a space-saving 6 ball advanced. Pb-Free 1.0x1.5 mm2 CSP package. Pin 1 VIN NC VOUT ON GND FLAGB BOTTOM TOP Ordering Information Part Min Current Limit [mA] Blanking Current Limit Time [ms] Auto-Restart Time [ms] FPF2024 100 10 FPF2025 100 10 FPF2026 100 10 FPF2027 100 0 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B ON Pin Activity FLAGB Top Mark 70 Active HI Open Drain S2 70 Active LO CMOS S3 NA Active HI Open Drain S4 NA Active HI Open Drain S5 1 www.fairchildsemi.com FPF2024/5/6/7 September 2008 Full Functional Load Switch With 100mA Current Limit Typical Application Circuit VIN VOUT TO LOAD GND FPF2024, FPF2026, FPF2027 ON OFF ON FLAGB VIN VOUT TO LOAD ON OFF ON GND FPF2025 FLAGB Functional Block Diagram VIN FPF2024, FPF2026, FPF2027 UVLO CONTROL LOGIC ON THERMAL PROTECTION CURRENT LIMIT FLAGB VOUT GND VIN FPF2025 UVLO ON CONTROL LOGIC THERMAL PROTECTION CURRENT LIMIT FLGAB VOUT GND ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 2 www.fairchildsemi.com VIN A2 A1 VOUT NC B2 B1 GND ON C2 C1 FLAGB OUTB 1.0X1.5CSP Bottom View Pin Description Pin Name A1 VOUT A2 VIN B1 GND B2 NC C1 FLAGB C2 ON Function Switch Output: Output of the power switch Supply Input: Input to the power switch and the supply voltage for the IC Ground No Connection Fault Output: Active LO, open drain output for FPF2024/6/7 and CMOS output for FPF2025. FLAGB indicates an over current, supply under voltage or over temperature state ON/OFF Control Input, Active High for FPF2024/6/7 and Active LO for FPF2025 Absolute Maximum Ratings Parameter Min. VIN, VOUT, ON, FLAGB to GND -0.3 Power Dissipation @ TA = 25°C (Note 1) Maximum Continuous Switch Current Max. Unit 6 V 1.2 W 0.2 A Operating Temperature Range -40 125 °C Storage Temperature -65 150 °C 85 °C/W Thermal Resistance, Junction to Ambient Electrostatic Discharge Protection HBM 5500 V CDM 1500 V Note1: Package power dissipation on 1square inch pad, 2 oz. copper board. Recommended Operating Range Parameter Min. Max. VIN 1.6 5.5 V Ambient Operating Temperature, TA -40 85 °C ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 3 Unit www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Pin Configuration VIN = 1.6 to 5.5V, TA = -40 to +85°C unless otherwise noted. Typical values are at VIN = 3.3V and TA = 25°C. Parameter Symbol Conditions Min. Typ. Max. Units 5.5 V 4 µA Basic Operation Operating Voltage 1.6 VIN Quiescent Current IQ Shutdown Current ISHDN IOUT = 0mA, VON Active, VIN = 1.8V (Average) 1 VON = VIN (FPF2025) VON = GND (FPF2024/6/7), IOUT = 0 1 TA = 25°C, VIN = 5.5V TA = -40 to +85°C, VIN = 5.5V On-Resistance RON 120 TA = 25°C,VIN = 3.3V TA = -40 to +85°C, VIN = 3.3V 140 TA = 25°C,VIN = 1.6V ON Input Logic High Voltage (ON) VIH ON Input Logic Low Voltage VIL 180 VIN = 1.6V 0.8 VIN = 5.5V 1.5 315 215 350 225 325 225 360 305 490 305 580 ISWOFF FLAGB Output Logic Low Voltage FLAGB Output Logic High Voltage VIN = 1.6V 0.45 VIN = 5.5V 0.9 VON = VIN, VOUT = 0V µA 1 µA 0.1 0.2 VIN = 1.8V, ISINK = 1mA 0.1 0.3 VIN = 5.5V, ISOURCE = 1mA, FPF2025 5.2 5.4 VIN = 1.6V, ISOURCE = 1mA, FPF2025 1.2 1.35 V 1 VIN = 5.5V, ISINK = 1mA VIN = 5.5V, Switch on, FPF2024, FPF2026, FPF2027 FLAGB Output High Leakage Current mΩ V VON = VIN or GND ON Input Leakage Off Switch Leakage TA = -40 to +85°C, VIN = 1.6V 215 µA V V 1 µA 200 mA Protections Current Limit ILIM Thermal Shutdown Under Voltage Lockout UVLO VIN = 3.3V, VOUT = 3.0V,TA = 25°C 100 150 Shutdown Threshold TJ increasing 140 Return from Shutdown 130 Hysteresis 10 VIN Increasing 1.475 Under Voltage Lockout Hysteresis 1.525 °C 1.575 V 40 mV µs Dynamic Turn On Time tON RL = 500Ω, CL = 0.1µF 70 Turn Off Time tOFF RL = 500Ω 10 µs VOUT Rise Time tRISE RL = 500Ω, CL = 0.1µF 30 µs Over Current Blanking Time tBLANK FPF2024, FPF2025,FPF2026 Startup FLAGB Blanking Time tSTART_BLANK FPF2027 (Note2) Auto-Restart Time tRSTRT FPF2024, FPF2025 Sleep Mode Duration Wake-up Mode Duration 5 10 20 ms 5 10 20 ms 35 70 140 ms 128.5 257 514 ms 1 2 ms 0.5 Duty Cycle Wake-up: Sleep Mode Duty Cycle 1:257 Current Limit Response Time Moderate Over-current condition RL= 5Ohms 15 Blanking/Auto-Restart Duty Ratio tBLANK /tRSTRT (internally fixed) FPF2024, FPF2025 1:7 µs Note2: FPF2027 has a 10ms Startup FLAGB Blanking Time when the part is turned on via ON pin to ensure transient load currents settle down. ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 4 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Electrical Characteristics 0.3 70 69 VIN = 5.5V 68 0.2 TRestart (ms) ISHUTDOWN (uA) 0.25 VIN = 3.3V 0.15 67 66 0.1 65 VIN = 1.6V 0.05 64 0 -50 -25 0 25 50 75 63 -50 100 -25 0 o 1200 10.4 1100 10.2 1000 10 VIN = 1.8V 9.6 700 9.4 -25 0 25 50 75 9.2 -50 100 -25 0 o 350 350 300 300 250 o 85 C 50 oC 25 oC 150 4 5 6 100 75 100 VIN = 1.6 V VIN = 1.8 V 250 VIN = 3.3 V VIN = 5.5 V 150 -50 -25 0 25 50 Temperature C Figure 5. RDS(ON) vs. VIN FPF2024/5/6/7 Final. B 75 o VIN (V) ©2008 Fairchild Semiconductor Corporation 50 200 0 oC -25 oC -40 oC 200 3 25 Figure 4. TBlank vs. Temperature RDS(ON) (mOhms) RDS(ON) (mOhms) Figure 3. Quiescent Current vs. Temperature 2 100 Temperature (oC) Temperature ( C) 1 75 9.8 800 600 -50 50 Figure 2. TRestart vs. Temperature TBlank (ms) IQ (nA) Figure 1. Shutdown Current vs.Temperature 900 25 Temperature (oC) Temperature ( C) Figure 6. RDS(ON) vs. Temperature 5 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Typical Characteristics 160 160 o -40 C 159 158 -25 oC ILimit (mA) ILimit (mA) 158 o 0 C 156 o 25 C o 50 C 156 VIN = 1.6V 155 o 154 VIN = 5.5V 157 85 C VIN = 3.3V 154 152 1 2 3 4 5 153 -50 6 -25 0 75 100 Figure 8. ILimit vs. Temperature 2 VIN 2V/DIV VIN=3.3V CIN=10uF COUT=0.1uF RL=500Ω VON=3.3V 1.5 VIL = 5.5V VIH, VIL (V) 50 Temperature ( C) Figure 7. ILimit vs. VIN VON 2V/DIV VIH = 5.5 V 1 25 o VIN (V) VIL = 1.6 V 0.5 0 -50 ILOAD 10mA/DIV VIH = 1.6 V -25 0 25 50 75 VOUT 2V/DIV 100 o Temperature ( C) Figure 9. VIH, VIL vs Temperature VIN 2V/DIV VDRV (Note3) 2V/DIV VIN=3.3V CIN=10uF RL=500Ω VON=3.3V VON 2V/DIV 200 µs/DIV Figure 10. FPF2024 TON Response TBLANK FLAGB 2V/DIV VIN=VON=3.3V CIN=10uF COUT=0.1uF RL=500Ω ILOAD 100mA/DIV ILOAD 10mA/DIV VOUT 2V/DIV VOUT 2V/DIV 100us/DIV 5 ms/DIV Figure 12. FPF2024 TBLANK Response Figure 11. FPF2024 TOFF Response Note3: VDRV signal forces the device to go into overcurrent condition by loading a 7.5Ω. ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 6 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Typical Characteristics VIN=VON=3.3V CIN=10uF COUT=0.1uF RL=500Ω VDRV (Note3) 2V/DIV FLAGB 2V/DIV VIN 2V/DIV VON 2V/DIV TRESTART ILOAD 100mA/DIV ILOAD 100mA/DIV VIN=VON=3.3V CIN=10uF COUT=10uF RL=5Ω VOUT 2V/DIV VOUT 2V/DIV 10 ms/DIV Figure 13. FPF2024 TRESTART Response 50us/DIV Figure 14. FPF2024 Current Limit Response Time (Output is loaded by 5Ω and COUT = 10uF) VIN 2V/DIV VIN 2V/DIV VON 2V/DIV VON 2V/DIV ILOAD 100mA/ DIV VOUT 2V/DIV VIN=VON=3.3V CIN=10uF COUT=100uF RL=5Ω ILOAD 2A/DIV 500us/DIV 20us/DIV Figure 16. FPF2024 Short Circuit Response Time (Output shorted to GND while the switch is in normal operation) VDRV (Note3) 2V/DIV VIN=VON=3.3V CIN=10uF VOUT =GND ILOAD 100mA/DIV ILOAD 100mA/DIV ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B VIN=VON=3.3V CIN=10uF COUT=0.1uF RL=100Ω FLAGB 2V/DIV VOUT 2V/DIV 20us/DIV Figure 17. FPF2024 Current Limit Response (Input and enable pin are tied together and VOUT is shorted to GND) COUT=0.1uF RL=100Ω VOUT 2V/DIV Figure 15. FPF2024 Current Limit Response Time (Output is loaded by 5Ω and COUT = 100uF) VIN/VON 2V/DIV VIN=VON=3.3V CIN=10uF VOUT 2V/DIV 10 ms/DIV Figure 18.FPF2027 Over-Current Over-Current condition is applied while device in normal operation (FLAGB inserts immediately and reports the fault condition) 7 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Typical Characteristics VON 2V/DIV VON 2V/DIV VIN=3.3V CIN=10uF COUT=10uF RL=5Ω FLAGB 2V/DIV ILOAD 100mA/DIV VOUT 2V/DIV VOUT 2V/DIV 10 ms/DIV Figure 19. FPF2027 Startup FLAGB Blanking Time FPF2024/5/6/7 Final. B VIN=3.3V CIN=10uF COUT=0.1uF RL=7.5Ω FLAGB 2V/DIV ILOAD 100mA/DIV ©2008 Fairchild Semiconductor Corporation Device is ON 20ms/DIV Figure 20. FPF2025 TBLANK and TRESTART (Active LO Device) 8 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Typical Characteristics On/Off Control FPF2024-FPF2027 series Full-Function switches are current limited load switches with ultra-low power consumption. The core of each device consists of a 230mW P-channel MOSFET featuring slow turn-on to limit the inrush current, fast turn-off, current limit, UVLO(under-voltage lockout) and thermal shutdown protection features and a FLAGB output that indicates that a fault condition has occurred. The ON pin controls the state of the switch. The FPF2024FPF2027 series features both active high and low configurations to accommodate various application requirements. FPF2024, FPF2026 and FPF2027 are active high switches while the FPF2025 is an active low device. Applying a continuous high or low signal depending on the switch configuration, will hold the switch in the ON state. The load switch will move into the OFF state when the ON pin is inactive. In addition, FPF2026 moves into the OFF state if a current fault is encountered for longer duration than the Blanking Time. For all versions, an undervoltage on VIN or a junction temperature in excess of 140°C overrides the ON control and turns off the switch. Some versions in the FPF202x series also feature Current Limit Blanking and Auto-Restart. The FPF202x family achieves an ultra-low current consumption of 1µA through a proprietary ”Sleep-Wakeup modes” implementation. Full functionality is guaranteed for operating voltages down to 1.6V over the -40°C to +85°C temperature range. In addition, a current fault condition longer than the Blanking Time will cause the switch to turn off in the FPF2024, FPF2025 and FPF2026. The FPF2024 and FPF2025 have an AutoRestart feature which will automatically turn the switch on again after 70ms. For the FPF2026, the ON pin must be toggled to turn the switch on again. The FPF2027 does not turn off in response to an over current condition, and remains in a constant current mode for so long as the ON pin is active, and the thermal shutdown or UVLO are not activated. Sleep and Wakeup Mode Description The ultra-low power consumption of FPF2024-FPF2027 is achieved through the implementation of proprietary Sleep/ Wakeup modes. The FPF2024-FPF2027 family turns on in Startup mode where it checks for potential load current, temperature, and undervoltage faults for 10ms. If no faults are detected during this startup period, the FPF2024-FPF2027 goes into a Sleep mode where it stays for 257ms. At the end of the Sleep period, the part goes into Wakeup mode to check for any fault condition. If no fault is detected in 1ms, the part goes back to Sleep mode. The 1:257 Wakeup/Sleep duty cycle results in an overall average current consumption of 1 µA (typ). The ON pin control voltage and VIN pin have independent recommended operating ranges. The ON pin voltage can be driven by a voltage level higher than the input voltage. Fault Reporting Over-current, input under-voltage, or over-temperature fault conditions are signaled out by the FLAGB pin going low. FPF2024, FPF2025 and FPF2026 have a current fault blanking feature which prevents current faults lasting shorter than the Blanking Time of 10ms (typ) from triggering the fault signal (FLAGB) output. During Sleep mode the thermal and under-voltage conditions are not monitored to reduce the current consumption of the device. The switch current limiting circuitry is active at all times and protects the FPF2024-FPF2027 against excessive load currents in all modes. If the over-current condition persists beyond the Blanking Time, the FPF2024 and FPF2025 pull the FLAGB pin low and shut the switch off. If the ON pin is kept active, an Auto-Restart feature releases the FLAGB pin and turns the switch on again after 70ms. While in the Wakeup mode, a current fault event will prevent the part from re-entering into Sleep mode even if input voltage and temperature faults are not present. In such a case, the part functions according to its feature set, e.g., it performs its normal Blanking, Auto-Restart or Latch-off functions as expected. If the over-current condition is removed from the output, the part will go back into Sleep mode after 10ms. The representative state diagrams of the FPF2024-FPF2027 are given in Figure 21, Figure 22 and Figure 23. If the over-current condition persists beyond the Blanking Time, the FPF2026 has a Latch-Off feature which pulls the FLAGB pin low and shuts the switch off. The switch is kept off and the FLAGB pin is kept low until the ON pin is toggled. The FPF2027 responds to an overload condition by immediately pulling the FLAGB pin low and the switch remains in constant current mode until the output overload condition is removed. The FPF2027 has a Start-Up Blanking feature which prevents current faults related to start-up transients from triggering the FLAGB output. The Startup Blanking feature is effective for the first 10ms (typ) following device turn-on via ON pin. The ultra-low quiescent current consumption of 1µA along with the very-low minimum operating voltage of 1.6V, make the FPF2024-FPF2027 an ideal full-function load switch for ultraportable applications. The FPF2024, FPF2026 and FPF2027 have an open-drain MOSFET FLAGB output which requires a pull-up resistor between VIN and FLAGB. A 100KΩ pull up resistor is recommended. The FPF2025 has a CMOS FLAGB output and does not require a pull-up resistor. During shutdown, the pulldown on FLAGB is disabled to reduce current draw from the supply. ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 9 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Description of Operation Full Functional Load Switch With 100mA Current Limit Current Limiting The current limit function ensures that the current through the switch does not exceed a maximum value while not limiting at less than a minimum value. The minimum current at which the parts will limit the load current is internally set to 100mA. The switch current limiting circuitry is active at all times(Sleep and Wakeup mode) and protects the FPF2024-FPF2027 against excessive load currents in all modes. The proprietary current limiting circuit responds to an over-current condition in 15 µs (typ). Undervoltage Lockout (UVLO) The undervoltage lockout feature turns-off the switch if the input voltage drops below the undervoltage lockout threshold. With the ON pin active, the input voltage rising above the undervoltage lockout threshold will cause a controlled turn-on of the switch and will limit current over-shoots. The UVLO feature is disabled during Sleep mode. If device is in the UVLO condition, FLAGB goes low and indicates the fault. If the input voltage goes below UVLO voltage but remains above 1.3V (typ) during Sleep mode, the switch is kept on until the next Wakeup cycle, where the UVLO violation will be detected. If the input voltage falls below 1.3V in Sleep mode, the switch is immediately turned off. Thermal Shutdown The Thermal Shutdown protects the device from internally or externally generated excessive temperatures. The Thermal shutdown feature is disabled during Sleep mode. However, excessive load currents that may result in high power dissipation will be detected during Sleep mode and will activate the fullfunction Wakeup mode, which has thermal shutdown protection. During an over-temperature condition the FLAGB is pulled low and the switch is turned-off. If the temperature of the die drops below the threshold temperature, the switch automatically turnson again, To avoid unwanted thermal oscillations, a 10°C (typ) thermal hysteresis is implemented between thermal shutdown entry and exit temperatures. ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 10 www.fairchildsemi.com State Diagram for the part options with Blanking and Auto-Restart (FPF2024/5) OFF Notes: All States return to OFF when ON is removed. Typical timing values are shown . Key: I=Load Switch current, V=Input Voltage, T= Die Temperature ON I FAULT (V OR T) FAULT STARTUP & BLANKING (Full-feature for 10ms) (I AND V AND T) OK SLEEP (Monitor SW current only for 257ms) I FAULT END 257ms I FAULT (I AND V AND T) OK END 70ms AUTORESTART 70ms WAKEUP (Full-feature for 1ms) (V OR T) FAULT Figure 21. Representative State Diagram of FPF2024/5 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 11 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Description of Operation cont. State Diagram for the part options with Blanking only(no Auto-Restart -FPF2026) OFF Notes: All States return to OFF when ON is removed. Typical timing values are shown . Key: I=Load Switch current, V=Input Voltage, T=Die Temperature I FAULT ON I FAULT STARTUP & BLANKING (Full-feature for 10ms) I OR V OR T) FAULT (I AND V AND T) OK SLEEP (Monitor SW current only for 257ms) I FAULT END 257ms (I AND V AND T) OK WAKEUP (Full-feature for 1ms) (V OR T) FAULT Figure 22. Representative State Diagram of FPF2026 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 12 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Description of Operation cont. State Diagram for the part options with no Blanking (FPF2027) OF F Notes: All States return to OFF w hen ON is rem oved. T ypical tim ing values are show n . Key : I= Load Switch current, V=Input Voltage, T= D ie T em perature ON I F AU LT ST A R T U P & B L A NK IN G (F ull-feature for 10m s ) I OR V OR T) F AU LT (I AN D V AN D T) OK SL EEP (M onitor SW current only for 257ms ) I FAU LT EN D 257m s (I AN D V AN D T) OK WA K EUP (Full-feature for 1m s ) (V OR T) F AU LT Figure 23. Representative State Diagram of FPF2027 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 13 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Description of Operation cont. Improving Thermal Performance To limit the voltage drop on the input supply caused by transient in-rush currents when the switch is turned on into a discharged load capacitor or a short-circuit, a capacitor is recommended to be placed between VIN and GND. The FPF2024-FPF2027 series feature a slow turn-on to limit the inrush current and requires a smaller input capacitor. A 1uF ceramic capacitor, CIN, placed close to the pins is typically sufficient. Higher values of CIN can be used to further reduce the voltage drop. An improper layout could result in higher junction temperature and ultimately trigger the thermal shutdown protection feature. This concern applies particularly significant for the FPF2027 where the switch is in constant current mode in the overload conditions. The following techniques have been identified to improve the thermal performance of this family of devices. These techniques are listed in order of the significance of their impact. Output Capacitor NC pin can be connected to the GND plane to improve thermal performance. A 0.1uF capacitor COUT, should be placed between VOUT and GND. This capacitor will prevent parasitic board inductances from forcing VOUT below GND when the switch turns-off. For the FPF2024, FPF2025 and FPF2026, the total output capacitance needs to be kept below a maximum value, COUT(max), to prevent the part from registering an over-current condition beyond the Blanking Time and turning-off the switch. The maximum output capacitance can be determined from the following formula: COUT(Max)= The VIN, VOUT and GND pins will dissipate most of the heat generated during a high load current condition. Using wide traces will help minimize parasitic electrical effects, along with minimizing the case to ambient thermal impedance. The layout suggested in Figure 24 provides each pin with adequate copper so that heat may be transferred out of the device as efficiently as possible. The low-power FLAGB and ON pin traces may be laid-out to maximize the area available to the ground pad. ILIM(Max) x tBLANK(Min) VIN Placing the input and output capacitors as close to the device as possible also contributes to heat dissipation, particularly during high load currents. Power Dissipation During normal operation as a switch, the power dissipation is small and has little effect on the operating temperature of the part. The maximum power dissipation while switch is in normal operation occurs just before a part enters the current limit. This may be calculated using the formula bellow: FPF202X Demo Board FPF202X Demo board has components and circuitry to demonstrate the functions and features of the FPF202X load switch family. An N-Channel MOSFET(Q), in series with a 7.5Ω resistor, are connected between VOUT and the GND pin of the device. By turning on the Q transistor, the 7.5Ω is loaded to the output voltage and simulates an over-current condition. The R2 resistor is connected between FLAGB pin and input voltage as pull-up resistor for FPF2024, FPF2026 and FPF2027 devices. The FPF2025 does not require a pull-up resistor due to its CMOS output structure. PMax(Normal Operation) = (ILIM(Max))2 x RON(Max) = (0.2)2 x 0.58 = 23.2 mW, for VIN=1.6V If the part goes into current limit, the maximum power dissipation occurs when the output of switch is shorted to ground. For the FPF2024 and FPF2025, the power dissipation will scale with the Auto-Restart Time, tRSTRT, and the Over Current Blanking Time, tBLANK. In this case the maximum power dissipated for the FPF2024 and FPF2025 is: PMax(Current limit) = = tBLANK tBLANK + tRSTRT The thermal performance of the board is improved using the techniques recommended in the layout recommendations section of datasheet. x VIN(Max) x ILIM(Max) 10 x 5.5 x 0.2 =137 mW 10 + 70 Take note that this is below the maximum package power dissipation, and the thermal shutdown feature protection provides additional safety to protect the part from damage due to excessive heating. The junction temperature is only able to increase to the thermal shutdown threshold. Once this temperature has been reached, toggling ON will have no affect until the junction temperature drops below the thermal shutdown exit temperature. For the FPF2027, a short on the output will cause the part to operate in a constant current state dissipating a worst case power of: PMax = VIN(Max) X ILIM(Max) = 5.5X0.2 =1.1 W Output of FPF2027 is shorted to GND. Figure 24. FPF202X proper layout This power dissipation is significant enough that it will activate the thermal shutdown protection, and the part will cycle in and out of thermal shutdown so long as the ON pin is active and the output short is present. ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 14 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Application Information Input Capacitor Full Functional Load Switch With 100mA Current Limit Figure 28. TOP, SST and SMT Figure 25. Top Layer Figure 26. Bottom Layer Figure 27. SST ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 15 www.fairchildsemi.com Full Functional Load Switch With 100mA Current Limit Dimensional Outline and Pad Layout Product FPF2024/5/6/7 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B D 1.500+/- 0.030 E 1.000 +/-0.030 16 X 0.240 Y 0.240 www.fairchildsemi.com TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidianries, and is not intended to be an exhaustive list of all such trademarks. FRFET® Global Power ResourceSM Green FPS™ Green FPS™ e-Series™ GTO™ IntelliMAX™ ISOPLANAR™ MegaBuck™ MICROCOUPLER™ MicroFET™ MicroPak™ MillerDrive™ MotionMax™ Motion-SPM™ OPTOLOGIC® OPTOPLANAR® Build it Now™ CorePLUS™ CorePOWER™ CROSSVOLT™ CTL™ Current Transfer Logic™ EcoSPARK® EfficentMax™ EZSWITCH™ * ™ Fairchild® Fairchild Semiconductor® FACT Quiet Series™ FACT® FAST® FastvCore™ FlashWriter® * FPS™ F-PFS™ Programmable Active Droop™ QFET® QS™ Quiet Series™ RapidConfigure™ ™ Saving our world, 1mW at a time™ Saving our world, 1W at a time™ Saving our world, 1kW at a time™ SmartMax™ SMART START™ SPM® STEALTH™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SupreMOS™ SyncFET™ ® PDP SPM™ Power-SPM™ PowerTrench® The Power Franchise® TinyBoost™ TinyBuck™ TinyLogic® TINYOPTO™ TinyPower™ TinyPWM™ TinyWire™ µSerDes™ UHC® Ultra FRFET™ UniFET™ VCX™ VisualMax™ ® * EZSWITCH™ and FlashWriter® are trademarks of System General Corporation, used under license by Fairchild Semiconductor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ANTI-COUNTERFEITING POLICY Fairchild Semiconductor Corporation’s Anti-Counterfeiting Policy. Farichild’s Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com, under Sales Support. Counterfeiting of semiconductor parts is a growing problem in the industry. All manufactures of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed application, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Farichild strongly encourages customers to purchase Farichild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild’s quality standards for handing and storage and provide access to Farichild’s full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address and warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Farichild is committed to committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative / In Design Datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve the design. Obsolete Not In Production Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The datasheet is for reference information only. Rev. I36 ©2008 Fairchild Semiconductor Corporation FPF2024/5/6/7 Final. B 17 www.fairchildsemi.com