SPICE MODEL: PDS1040L PDS1040L 10A LOW VF SCHOTTKY BARRIER RECTIFIER PowerDI ä5 NEW PRODUCT Features · Guard Ring Die Construction for Transient Protection · · · Very Low Forward Voltage Drop · · · A2 L1 High Forward Surge Current Capability PowerDIä5 For Use in Low Voltage, High Frequency Inverters, Free Wheeling, and Polarity Protection Applications E E1 Lead Free Finish, RoHS Compliant (Note 1) "Green" Molding Compound (No Br, Sb) L1 e Qualified to AEC-Q101 Standards for High Reliability A2 b1 b1 D D2 b2 Mechanical Data Case: PowerDI 5 · · Moisture sensitivity: Level 1 per J-STD-020C E2 Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 Polarity: See Diagram LEFT PIN RIGHT PIN Marking: See Page 3 Weight: 0.096 grams (approx.) Maximum Ratings Max A 1.05 1.15 A2 0.33 0.43 b1 0.80 0.99 b2 1.70 1.88 D 3.90 4.05 3.05 NOM 6.40 E E L1 5.30 BOTTOMSIDE HEAT SINK 5.45 3.55 NOM E2 b1 6.60 1.84 NOM e e b1 Min E1 W e3 Dim D2 L ä · · · · · A D b2 L 0.75 0.95 L1 0.50 0.65 W 1.20 1.50 All Dimensions in mm Note: Pins Left & Right must be electrically connected at the printed circuit board. @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (see also Figure 5) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Operating Junction Temperature Range VR £ 80% VRRM VR £ 50% VRRM Storage Temperature Range Thermal Characteristics Symbol Value Unit VRRM VRWM VR 40 V VR(RMS) 28 V IO 10 A IFSM 275 A TJ -65 to +130 -65 to +150 °C TSTG -65 to +150 °C @ TA = 25°C unless otherwise specified Characteristic Thermal Resistance Junction to Soldering Point Symbol Typ Max Unit RqJS ¾ 1.5 °C/W Thermal Resistance Junction to Ambient Air (Note 2) RqJA 85 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 3) RqJA 65 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 4) RqJA 50 ¾ °C/W Notes: 1. 2. 3. 4. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. DS30486 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 3 www.diodes.com PDS1040L ã Diodes Incorporated @ TA = 25°C unless otherwise specified Min Typ Max V(BR)R 40 ¾ ¾ V IR = 600mA Forward Voltage VF ¾ ¾ ¾ ¾ ¾ ¾ 0.41 0.30 0.42 0.32 0.44 0.35 0.46 0.35 0.47 0.41 0.49 0.43 V IF = 6A, TS = 25°C IF = 6A, TS = 125°C IF = 8A, TS = 25°C IF = 8A, TS = 125°C IF = 10A, TS = 25°C IF = 10A, TS = 125°C Reverse Current (Note 5) IR ¾ ¾ 0.07 12.5 0.6 25 mA TS = 25°C, VR = 40V TS = 100°C, VR = 40V Characteristic Symbol Reverse Breakdown Voltage (Note 5) IF, INSTANTANEOUS FORWARD CURRENT (A) Notes: Unit Test Condition 5. Short duration test pulse used to minimize self-heating effect. 100 10 Tj = 150°C Tj = +25°C 1 Tj = 125°C 100m 100n Tj = 100°C 10m Tj = 85°C 10n Tj = 25°C 1n 1m Tj = -65°C Tj = -65°C 100r 0 100 200 300 500 400 600 10 0 20 40 30 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics VF, INSTANTANEOUS FORWARD VOLTAGE (mV) Fig. 1 Typical Forward Characteristics 1,000 10,000 f = 1MHz 100 CT, TOTAL CAPACITANCE (pF) IR, INSTANTANEOUS REVERSE CURRENT (mA) NEW PRODUCT Electrical Characteristics Tj = 150°C Tj = 125°C 10 Tj = 100°C 1,000 Tj = 85°C 100 1.0 10 0 20 30 40 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 3 Typical Reverse Characteristics DS30486 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 2 of 3 www.diodes.com 0 5 10 15 20 25 30 35 40 VR, REVERSE VOLTAGE (V) Fig. 4 Typical Total Capacitance vs. Reverse Voltage PDS1040L PF(AV), AVERAGE FORWARD POWER DISSIPATION (W) IF, DC FORWARD CURRENT (A) 4 10 7.5 Note 6 5.0 Note 2 2.5 0 IPK = 1 (DC) IAV 3 2 1 0 0 25 50 100 75 0 150 125 TA, AMBIENT TEMPERATURE (°C) Fig. 5 DC Forward Current Derating 12 15 6 9 3 IF(AV), AVERAGE FORWARD CURRENT (A) Fig. 6 Forward Power Dissipation 170 TA, DERATED AMBIENT TEMPERATURE (°C) NEW PRODUCT 12.5 150 Note 7 130 110 90 70 Note 2 50 30 10 -10 -30 0 10 20 30 40 VR, DC REVERSE VOLTAGE (V) Fig. 7 Operating Temperature Derating Ordering Information Notes: 2. 3. 4. 5. 6. 7. 8. (Note 8) Device Packaging Shipping PDS1040L-13 PowerDIä5 5000/Tape & Reel FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. Short duration test pulse used to minimize self-heating effect. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 18.8mm x 14.4mm. Anode pad dimensions 5.6mm x 3.0mm. Devices mounted such that RqJA @ 19°C/W. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information S1040L YYWWK S1040L = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last two digits of year ex: 04 for 2004 WW = Week code 01 to 52 K = Factory designator DS30486 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 3 www.diodes.com PDS1040L