SPICE MODEL: PDS5100 PDS5100 5A HIGH VOLTAGE SCHOTTKY BARRIER RECTIFIER PowerDI ä5 NEW PRODUCT Features · · · · · · · · Guard Ring Die Construction for Transient Protection A D A2 b2 High Surge Current Capability PowerDIä5 L1 Low Leakage Current Low Forward Voltage Drop E1 High Forward Surge Current Capability Lead Free Finish, RoHS Compliant (Note 1) L1 "Green" Molding Compound (No Br, Sb) e Qualified to AEC-Q101 Standards for High Reliability A2 b1 b1 D D2 b2 Mechanical Data · · Case: PowerDIä5 · · Moisture Sensitivity: Level 1 per J-STD-020C · · · Polarity: See Diagram E2 1.15 0.43 b1 0.80 0.99 b2 1.70 1.88 D 3.90 4.05 3.05 NOM 6.40 5.30 b1 LEFT PIN RIGHT PIN BOTTOMSIDE HEAT SINK 5.45 3.55 NOM E2 e b1 6.60 1.84 NOM e L1 Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 e3 Weight: 0.093 grams (approximate) 1.05 0.33 E1 W Marking: See Page 3 A E E Max A2 D2 L Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 Min Dim E L 0.75 0.95 L1 0.50 0.65 W 1.20 1.50 All Dimensions in mm Note: Pins Left & Right must be electrically connected at the printed circuit board. Maximum Ratings @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (See also figure 5) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Operating Temperature Range Storage Temperature Range Thermal Characteristics Symbol Value Unit VRRM VRWM VR 100 V VR(RMS) 71 V IO 5 A IFSM 120 A Tj -65 to +150 °C TSTG -65 to +175 °C @ TA = 25°C unless otherwise specified Characteristic Symbol Typ Max Thermal Resistance Junction to Soldering Point RqJS 1.3 2.6 °C/W Thermal Resistance Junction to Ambient Air (Note 2) RqJA 90 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 3) RqJA 70 ¾ °C/W Thermal Resistance Junction to Ambient Air (Note 4) RqJA 50 ¾ °C/W Notes: 1. 2. 3. 4. Unit RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. DS30483 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 3 www.diodes.com PDS5100 ã Diodes Incorporated @ TA = 25°C unless otherwise specified Symbol Min Typ Max Unit V(BR)R 100 ¾ ¾ V IR = 200mA Forward Voltage VF ¾ ¾ ¾ ¾ ¾ 0.74 0.64 0.60 0.81 0.68 0.79 0.68 0.64 0.89 0.73 V IF = 5A, TS = 25°C IF = 5A, TS = 100°C IF = 5A, TS = 125°C IF = 10A, TS = 25°C IF = 10A, TS = 125°C Reverse Leakage Current (Note 5) IR ¾ ¾ 0.002 0.5 2 0.2 5 20 mA Characteristic Reverse Breakdown Voltage (Note 5) Notes: Test Condition TS = 25°C, VR = 100V TS = 100°C, VR = 100V TS = 125°C, VR = 100V 5. Short duration test pulse used to minimize self-heating effect. 10 IF, INSTANTANEOUS FORWARD CURRENT (A) 100 Tj = +25°C 1 10 1 0.1 Tj = 150°C 0.1 Tj = 125°C 0.01 0.01 Tj = 100°C 0.001 Tj = 85°C Tj = 25°C 0.0001 0.001 Tj = -65°C Tj = -65°C 0.00001 0 100 300 200 400 500 600 700 800 900 1000 1100 1200 0.0001 0 VF, INSTANTANEOUS FORWARD VOLTAGE (mV) Fig. 1 Typical Forward Characteristics 60 40 20 100 80 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics 400 10 350 Tj = +150°C 1.0 CT, TOTAL CAPACITANCE (pF) IR, LEAKAGE CURRENT (mA) NEW PRODUCT Electrical Characteristics Tj = +125°C Tj = +100°C 0.1 Tj = +85°C f = 1MHz 300 250 200 150 100 50 0 0.01 0 0 20 40 60 80 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 3 Typical Reverse Characteristics DS30483 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 5 10 15 20 25 30 35 40 100 2 of 3 www.diodes.com VR, REVERSE VOLTAGE (V) Fig. 4 Typical Total Capacitance vs. Reverse Voltage PDS5100 4 PF, FORWARD POWER DISSIPATION (W) IF, DC FORWARD CURRENT (A) 6.0 4.5 Note 4 3.0 1.5 Note 2 0 IPK = 1 (DC) IAV 3 2 1 0 0 50 25 75 100 125 0 150 1 2 3 4 5 6 7 8 9 10 IF, FORWARD CURRENT (A) Fig. 6 Forward Power Dissipation TA, AMBIENT TEMPERATURE (°C) Fig. 5 DC Forward Current Derating 200 TA, DERATED AMBIENT TEMPERATURE (°C) NEW PRODUCT 7.5 Note 2 160 120 80 40 0 0 25 50 100 75 VR, DC REVERSE VOLTAGE (V) Fig. 7 Operating Temperature Derating Ordering Information Notes: 2. 3. 4. 5. 6. (Note 6) Device Packaging Shipping PDS5100-13 PowerDIä5 5000/Tape & Reel FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. Short duration test pulse used to minimize self-heating effect. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information S5100 YYWWK S5100 = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last digit of year ex: 04 for 2004 WW = Week code 01 to 52 K = Factory Designator DS30483 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 3 www.diodes.com PDS5100