MC74VHC1G86 2-Input Exclusive OR Gate The MC74VHC1G86 is an advanced high speed CMOS 2–input Exclusive OR gate fabricated with silicon gate CMOS technology. It achieves high speed operation similar to equivalent Bipolar Schottky TTL while maintaining CMOS low power dissipation. The internal circuit is composed of three stages, including a buffer output which provides high noise immunity and stable output. The MC74VHC1G86 input structure provides protection when voltages up to 7V are applied, regardless of the supply voltage. This allows the MC74VHC1G86 to be used to interface 5V circuits to 3V circuits. • • • • • • • http://onsemi.com High Speed: tPD = 3.5ns (Typ) at VCC = 5V Low Power Dissipation: ICC = 2µA (Max) at TA = 25°C Power Down Protection Provided on Inputs Balanced Propagation Delays Pin and Function Compatible with Other Standard Logic Families Latchup Performance Exceeds 300mA ESD Performance: HBM > 2000V; MM > 200V, CDM > 1500V SC–88A / SOT–353 DF SUFFIX CASE 419A MARKING DIAGRAM V8d Pin 1 d = Date Code IN B 1 IN A 2 5 VCC PIN ASSIGNMENT GND 3 4 OUT Y 1 IN B 2 IN A 3 GND 4 OUT Y 5 VCC Figure 1. 5–Lead SOT–353 Pinout (Top View) ORDERING INFORMATION LOGIC SYMBOL IN A IN B =1 See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. OUT Y FUNCTION TABLE Inputs Semiconductor Components Industries, LLC, 1999 December, 1999 – Rev. 2 1 Output A B Y L L H H L H L H L H H L Publication Order Number: MC74VHC1G86/D MC74VHC1G86 MAXIMUM RATINGS* Symbol Value Unit DC Supply Voltage Characteristics VCC –0.5 to +7.0 V DC Input Voltage VIN –0.5 to +7.0 V VOUT –0.5 to 7.0 –0.5 to VCC + 0.5 V IIK –20 mA IOK +20 mA IOUT +25 mA DC Supply Current, VCC and GND ICC +50 mA Power dissipation in still air, SC–88A † PD 200 mW Lead temperature, 1 mm from case for 10 s TL 260 °C DC Output Voltage VCC = 0 High or Low State Input Diode Current Output Diode Current (VOUT < GND; VOUT > VCC) DC Output Current, per Pin Storage temperature Tstg –65 to +150 °C * Maximum Ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute–maximum–rated conditions is not implied. Functional operation should be restricted to the Recommended Operating Conditions. †Derating — SC–88A Package: –3 mW/_C from 65_ to 125_C RECOMMENDED OPERATING CONDITIONS Characteristics DC Supply Voltage DC Input Voltage DC Output Voltage Operating Temperature Range Input Rise and Fall Time VCC = 3.3V ± 0.3V VCC = 5.0V ± 0.5V Symbol Min Max Unit VCC 2.0 5.5 V VIN 0.0 5.5 V VOUT 0.0 VCC V TA –55 +85 °C tr , tf 0 0 100 20 ns/V http://onsemi.com 2 MC74VHC1G86 DC ELECTRICAL CHARACTERISTICS VCC Symbol Parameter Test Conditions (V) Min 1.5 2.1 3.15 3.85 VIH Minimum High–Level Input Voltage 2.0 3.0 4.5 5.5 VIL Maximum Low–Level Input Voltage 2.0 3.0 4.5 5.5 VOH Minimum High–Level Output Voltage VIN = VIH or VIL VOL Maximum Low–Level Output Voltage VIN = VIH or VIL TA ≤ 85°C TA = 25°C Typ Max Min 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 VIN = VIH or VIL IOH = –50µA 2.0 3.0 4.5 1.9 2.9 4.4 VIN = VIH or VIL IOH = –4mA IOH = –8mA 3.0 4.5 2.58 3.94 VIN = VIH or VIL IOL = 50µA 2.0 3.0 4.5 VIN = VIH or VIL IOL = 4mA IOL = 8mA Max 2.0 3.0 4.5 TA ≤ 125°C Min Max 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 V 0.5 0.9 1.35 1.65 1.9 2.9 4.4 1.9 2.9 4.4 2.48 3.80 2.34 3.66 Unit V V V 0.0 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 V V IIN Maximum Input Leakage Current VIN = 5.5V or GND 0 to 5.5 ±0.1 ±1.0 ±1.0 µA ICC Maximum Quiescent Supply Current VIN = VCC or GND 5.5 2.0 20 40 µA ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎ AC ELECTRICAL CHARACTERISTICS (Cload = 50 pF, Input tr = tf = 3.0ns) TA ≤ 85°C TA = 25°C Symbol tPLH, tPHL CIN Parameter Maximum Propogation Delay, Input A or B to Y Test Conditions Min Typ Max Min Max TA ≤ 125°C Min Max Unit ns VCC = 3.0 ± 0.3V CL = 15 pF CL = 50 pF 4.4 5.7 11.0 14.5 13.0 16.5 15.5 19.5 VCC = 5.0 ± 0.5V CL = 15 pF CL = 50 pF 3.5 4.2 6.8 8.8 8.0 10.0 10.0 12.0 5.5 10 10 10 Maximum Input Capacitance pF Typical @ 25°C, VCC = 5.0V CPD Power Dissipation Capacitance (Note 1.) pF 10 1. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no–load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 3 MC74VHC1G86 TEST POINT VCC A or B OUTPUT 50% DEVICE UNDER TEST GND tPLH Y tPHL CL* 50% VCC *Includes all probe and jig capacitance Figure 2. Switching Waveforms Figure 3. Test Circuit DEVICE ORDERING INFORMATION Device Nomenclature Device Order Number MC74VHC1G86DFT1 Circuit Indicator Temp Range Identifier MC 74 Technology Device Function Package Suffix Tape & Reel Suffix Package Type Tape and Reel Size VHC1G 86 DF T1 SC–88A / SOT–353 7–Inch/3000 Unit PACKAGE DIMENSIONS SC–88A / SOT–353 DF SUFFIX 5–LEAD PACKAGE CASE 419A–01 ISSUE B A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MM. G V 4 –B– S 1 2 3 D 5 PL 0.2 (0.008) M B M MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC ––– 0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 0.30 0.40 0.5 mm (min) N J C K 0.4 mm (min) H INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC ––– 0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 0.012 0.016 ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ 1.9 mm http://onsemi.com 4 0.65 mm 0.65 mm 5 DIM A B C D G H J K N S V MC74VHC1G86 10 PITCHES CUMULATIVE TOLERANCE ON TAPE ±0.2 mm (±0.008”) P0 K P2 D t TOP COVER TAPE E A0 + K0 SEE NOTE 2 B1 SEE NOTE 2 F + B0 W + D1 FOR COMPONENTS 2.0 mm × 1.2 mm AND LARGER P EMBOSSMENT FOR MACHINE REFERENCE ONLY INCLUDING DRAFT AND RADII CONCENTRIC AROUND B0 CENTER LINES OF CAVITY USER DIRECTION OF FEED *TOP COVER TAPE THICKNESS (t1) 0.10 mm (0.004”) MAX. R MIN. TAPE AND COMPONENTS SHALL PASS AROUND RADIUS “R” WITHOUT DAMAGE EMBOSSED CARRIER BENDING RADIUS 100 mm (3.937”) MAXIMUM COMPONENT ROTATION 10° EMBOSSMENT 1 mm MAX TYPICAL COMPONENT CAVITY CENTER LINE TAPE 1 mm (0.039”) MAX TYPICAL COMPONENT CENTER LINE 250 mm (9.843”) CAMBER (TOP VIEW) ALLOWABLE CAMBER TO BE 1 mm/100 mm NONACCUMULATIVE OVER 250 mm Figure 4. Carrier Tape Specifications EMBOSSED CARRIER DIMENSIONS (See Notes 1 and 2) Tape Size B1 Max 8 mm 4.35 mm (0.171”) D D1 E F K P P0 P2 R T W 1.5 +0.1/ –0.0 mm (0.059 +0.004/ –0.0”) 1.0 mm Min (0.039”) 1.75 ±0.1 mm (0.069 ±0.004”) 3.5 ±0.5 mm (1.38 ±0.002”) 2.4 mm (0.094”) 4.0 ±0.10 mm (0.157 ±0.004”) 4.0 ±0.1 mm (0.156 ±0.004”) 2.0 ±0.1 mm (0.079 ±0.002”) 25 mm (0.98”) 0.3 ±0.05 mm (0.01 +0.0038/ –0.0002”) 8.0 ±0.3 mm (0.315 ±0.012”) 1. Metric Dimensions Govern–English are in parentheses for reference only. 2. A0, B0, and K0 are determined by component size. The clearance between the components and the cavity must be within 0.05 mm min to 0.50 mm max. The component cannot rotate more than 10° within the determined cavity http://onsemi.com 5 MC74VHC1G86 t MAX 13.0 mm ±0.2 mm (0.512” ±0.008”) 1.5 mm MIN (0.06”) A 20.2 mm MIN (0.795”) 50 mm MIN (1.969”) FULL RADIUS G Figure 5. Reel Dimensions REEL DIMENSIONS Tape Size 8 mm A Max G t Max 330 mm (13”) 8.400 mm, +1.5 mm, –0.0 (0.33”, +0.059”, –0.00) 14.4 mm (0.56”) DIRECTION OF FEED BARCODE LABEL POCKET Figure 6. Reel Winding Direction http://onsemi.com 6 HOLE MC74VHC1G86 CAVITY TAPE TOP TAPE TAPE TRAILER (Connected to Reel Hub) NO COMPONENTS 160 mm MIN COMPONENTS DIRECTION OF FEED Figure 7. Tape Ends for Finished Goods “T1” PIN ONE TOWARDS SPROCKET HOLE SC–88A/SOT–353 (5 Pin) DEVICE User Direction of Feed Figure 8. Reel Configuration http://onsemi.com 7 TAPE LEADER NO COMPONENTS 400 mm MIN MC74VHC1G86 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION USA/EUROPE Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time) Email: ONlit–[email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549 Phone: 81–3–5487–8345 Email: [email protected] Fax Response Line*: 303–675–2167 800–344–3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com *To receive a Fax of our publications For additional information, please contact your local Sales Representative. N. America Technical Support: 800–282–9855 Toll Free USA/Canada http://onsemi.com 8 MC74VHC1G86/D