AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency General Description Features • • • • • • • • • • • • The AP5100 is a current mode step-down converter with a built-in power MOSFET to enable smallest solution size power conversion. VIN 4.75V to 24V Load current of up to 1.2A Internal Power MOSFET Stable with Low ESR Ceramic Output Capacitors Up to 90% Efficiency 0.1µA Shutdown Mode Fixed 1.4MHz Frequency Thermal Shutdown Cycle-by-Cycle Over Current Protection Resistor divider adjustable Output: 0.81V to 15V SOT26: Available in “Green” Molding Compound (no Br, Sb) Lead Free Finish/RoHS Compliant (Note 1) With the low series resistance power switch it enables a constant output current of up to 1.2A over a wide input supply range. The load and line regulation has excellent response time over the operating input voltage and temperature range. The AP5100 is self protected, through a cycle-by-cycle current limiting algorithm and an on chip thermal protection. The AP5100 will provide the voltage conversion with a low count of widely available standard external components. The AP5100 is available in SOT26 package. Applications • • • • Distributed Power Systems Battery Charger Pre-Regulator for Linear Regulators WLED Drivers Typical Applications 5 VIN BST 1 IN C1 C3 AP5100 SW .L1 6 VOUT D1 R1 ON OFF 4 EN GND FB 3 C6 C2 R2 Figure 1. Typical Application Circuit AP5100 Document number: DS32130 Rev. 1 - 2 1 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Typical Applications 5 VIN C1 10µF 25V (Continued) BST 1 IN R3 100kohm 4 Figure 2. 5 VIN EN D1 B230A R3 100Kohm R1 49.9kohm 3 GND FB C2 22µF 6.3V BST 1 IN AP5100 SW 4 C6 100pF 1.4MHz, 3.3V Output at 1A Step-Down Converter 6 C3 10nF D1 L1 10µH 1N5819HW-7 - Vout OFF ON VOUT 3.3V R2 16.2kohm 6V -12V C1 10µF 25V L1 3.3µH 6 AP5100 SW OFF ON C3 22nF EN GND FB - Vout - Vout C2 10µF 16V LED1 LED 2 3 R4 200Kohm 1% R2 40 ohm 1% LED 3 - Vout Figure 3. AP5100 Document number: DS32130 Rev. 1 - 2 White LED Driver Application 2 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Ordering Information AP5100 W G - 7 Device AP5100WG-7 Notes: Package Green Packing W : SOT26 G : Green 7 : Tape & Reel Package Code W Packaging (Note 2) SOT26 7” Tape and Reel Quantity Part Number Suffix 3000/Tape & Reel -7 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. Pin Assignments ( Top View ) BST 1 6 SW GND 2 5 IN FB 3 74 EN SOT26 AP5100 Document number: DS32130 Rev. 1 - 2 3 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Pin Descriptions Pin Name Pin # BST 1 GND 2 FB 3 EN 4 IN 5 SW 6 Description Bootstrap. To form a boost circuit, a capacitor is connected between SW and BST pins to form a floating supply across the power switch driver. This capacitor is needed to drive the power switch’s gate above the supply voltage. Typical values for CBST range from 0.1uF to 1uF. Ground. This pin is the voltage reference for the regulated output voltage. All control circuits are referenced to this pin. For this reason care must be taken in its layout. Feedback. To set the output voltage, connect this pin to the output resistor divider or directly to VOUT. To prevent current limit run away during a current limit condition, the frequency foldback comparator lowers the oscillator frequency when the FB voltage is below 400mV. On/Off Control Input. Do not leave this pin floating. To turn the device ON, pull EN above 1.2V and to turn it off pull below 0.4V. If enable/disable is not used, connect a 100kOhm resistor between EN to VIN. Supply Voltage. The AP5100 operates from a +4.75V to +24V unregulated input. A decoupling capacitor C1 is required to prevent large voltage spikes from appearing at the input. Place this capacitor near the IC. Switch Output. This is the reference for the floating top gate driver. Absolute Maximum Ratings Symbol ESD HBM ESD MM VIN (Note 3) Description VSW Human Body Model ESD Protection Machine Model ESD Protection Supply Voltage Switch Voltage VBST Boost Voltage TST TJ TL θJA θJC All Other Pins Storage Temperature Junction Temperature Lead Temperature Junction to Ambient Thermal Resistance (Note 4) Junction to Case Thermal Resistance (Note 4) Notes: Rating Unit 3 300 26 -0.3 to VIN + 0.3 KV V V V VSW + 6 V –0.3 to +6 -65 to +150 +150 +260 140 35 V °C °C °C °C/W °C/W 3. Exceeding these ratings may damage the device. 4. Test condition for SOT26: Measured on approximately 1” square of 1 oz copper. AP5100 Document number: DS32130 Rev. 1 - 2 4 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Recommended Operating Ratings Symbol VIN TA VOUT Notes: (Note 5) Description Supply Voltage Operating Ambient Temperature Range Output Voltage Rating Unit 4.75 to 24 °C °C V -25 to +85 0.81 to 15 5. The device function is not guaranteed outside of the recommended operating conditions. Electrical Characteristics ( VIN = 12V, TA = +25°C, unless otherwise noted) Symbol Parameter VFB IFB Feedback Voltage Feedback Current Switch-On Resistance (Note 6) Switch Leakage Current Limit (Note 6) Oscillator Frequency Fold-back Frequency Maximum Duty Cycle Minimum On-Time (Note 6) Under Voltage Lockout Threshold Rising Under Voltage Lockout Threshold Hysteresis EN Input Low Voltage EN Input High Voltage RDS(ON) fSW tON EN Input Current IS IQ Notes: Supply Current (Shutdown) Supply Current (Quiescent) Thermal Shutdown (Note 6) Test Conditions 4.75V ≤ VIN ≤ 24V VFB = 0.8V Min Typ. Max Unit 0.790 0.810 0.1 0.35 0.830 V µA Ω µA A MHz kHz % ns VEN = 0V, VSW = 0V VFB = 0.6V VFB = 0V VFB = 0.6V 10 1.1 3.8 2.4 1.4 480 87 100 4.0 1.7 4.2 150 mV 0.4 1.2 VEN = 2V VEN = 0V VEN = 0V VEN = 2V, VFB = 1V 0.3 0.1 0.1 0.4 140 V V V µA 1.0 1.0 µA mA °C 6. Guaranteed by design. AP5100 Document number: DS32130 Rev. 1 - 2 5 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Typical Performance Characteristics VIN=12V, VOUT =3.3V, L=3.3uH, C1=10uF, C2=22uF, TA=+25•C, unless otherwise noted. Steady State Test (IOUT=0.5A) Load Transient Test (IOUT=0.2A to 0.8A. Step at 0.8A/us) Time- 1us/div Time- 100us/div Start-up Through Enable (No Load) Start-up through Enable (IOUT=1A, resistive load) Time- 50us/div Time- 50us/div Shutdown Through Enable (No Load) Shutdown Through Enable (IOUT=1A, resistive load) Time- 50us/div Time- 50us/div AP5100 Document number: DS32130 Rev. 1 - 2 6 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Typical Performance Characteristics (Continued) Short Circuit Entry Short Circuit Recovery Time- 50us/div Time- 100us/div AP5100 Document number: DS32130 Rev. 1 - 2 7 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Application Information OPERATION The AP5100 is a current mode control, asynchronous buck regulator. Current mode control assures excellent line and load regulation and a wide loop bandwidth for fast response to load transients. Figure. 4 depicts the functional block diagram of AP5100. The operation of one switching cycle can be explained as follows. At the beginning of each cycle, HS (high-side) MOSFET is off. The EA output voltage is higher than the current sense amplifier output, and the current comparator’s output is low. The rising edge of the 1.4MHz oscillator clock signal sets the RS Flip-Flop. Its output turns on HS MOSFET. When the HS MOSFET is on, inductor current starts to increase. The Current Sense Amplifier senses and amplifies the inductor current. Since the current mode control is subject to sub-harmonic oscillations that peak Figure 4. AP5100 Document number: DS32130 Rev. 1 - 2 at half the switching frequency, Ramp slope compensation is utilized. This will help to stabilize the power supply. This Ramp compensation is summed to the Current Sense Amplifier output and compared to the Error Amplifier output by the PWM Comparator. When the sum of the Current Sense Amplifier output and the Slope Compensation signal exceeds the EA output voltage, the RS Flip-Flop is reset and HS MOSFET is turned off. The external Schottky rectifier diode (D1) conducts the inductor current. For one whole cycle, if the sum of the Current Sense Amplifier output and the Slope Compensation signal does not exceed the EA output, then the falling edge of the oscillator clock resets the Flip-Flop. The output of the Error Amplifier increases when feedback voltage (VFB) is lower than the reference voltage of 0.81V. This also increases the inductor current as it is proportional to the EA voltage. Functional Block Diagram 8 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Application Information (Continued) Setting the Output Voltage The output voltage can be adjusted from 0.81V to 15V using an external resistor divider. Table 1 shows a list of resistor selection for common output voltages. Resistor R1 is selected based on a design tradeoff between efficiency and output voltage accuracy. For high values of R1 there is less current consumption in the feedback network. However the trade off is output voltage accuracy due to the bias current in the error amplifier. R2 can be determined by the following equation: ⎛V ⎞ R1 = R 2 × ⎜⎜ OUT − 1⎟⎟ ⎝ 0.81 ⎠ VOUT (V) R1 (kΩ) R2 (kΩ) 1.8 80.6 (1%) 64.9 (1%) 2.5 49.9 (1%) 23.7 (1%) 3.3 49.9 (1%) 16.2 (1%) 5 49.9 (1%) 9.53 (1%) Table 1. Resistor Selection for Common Output Voltages Inductor Calculating the inductor value is a critical factor in designing a buck converter. For most designs, the following equation can be used to calculate the inductor value; L= VOUT × (VIN − VOUT ) VIN × ΔIL × fSW Where ΔIL is the inductor ripple current. And fSW is the buck converter switching frequency. Choose the inductor ripple current to be 30% of the maximum load current. The maximum inductor peak current is calculated from: IL(MAX) = ILOAD + AP5100 Document number: DS32130 Rev. 1 - 2 Peak current determines the required saturation current rating, which influences the size of the inductor. Saturating the inductor decreases the converter efficiency while increasing the temperatures of the inductor, the MOSFET and the diode. Hence choosing an inductor with appropriate saturation current rating is important. A 1µH to 10µH inductor with a DC current rating of at least 25% percent higher than the maximum load current is recommended for most applications. For highest efficiency, the inductor’s DC resistance should be less than 200mΩ. Use a larger inductance for improved efficiency under light load conditions. Input Capacitor The input capacitor reduces the surge current drawn from the input supply and the switching noise from the device. The input capacitor has to sustain the ripple current produced during the on time on the upper MOSFET. It must hence have a low ESR to minimize the losses. Due to large dI/dt through the input capacitors, electrolytic or ceramics should be used. If a tantalum must be used, it must be surge protected. Otherwise, capacitor failure could occur. For most applications, a 4.7µF ceramic capacitor is sufficient. Output Capacitor The output capacitor keeps the output voltage ripple small, ensures feedback loop stability and reduces the overshoot of the output voltage. The output capacitor is a basic component for the fast response of the power supply. In fact, during load transient, for the first few microseconds it supplies the current to the load. The converter recognizes the load transient and sets the duty cycle to maximum, but the current slope is limited by the inductor value. Maximum capacitance required can be calculated from the following equation: ΔIL 2 9 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Application Information (Continued) ΔIinductor 2 ) 2 Co = (Δ V + VOUT ) 2 − VOUT 2 External Bootstrap Diode L(IOUT + Where ΔV is the maximum output voltage overshoot. It is recommended that an external bootstrap diode be added when the input voltage is no greater than 5V or the 5V rail is available in the system. This helps improve the efficiency of the regulator. The bootstrap diode can be a low cost one such as IN4148 or BAT54. ESR of the output capacitor dominates the output voltage ripple. The amount of ripple can be calculated from the equation below: Vout capacitor = ΔIinductor × ESR 5V BST An output capacitor with ample capacitance and low ESR is the best option. For most applications, a 22µF ceramic capacitor will be sufficient. 1 AP5100 BOOST DIODE 10nF SW 6 External Diode The external diode’s forward current must not exceed the maximum output current. Since power dissipation is a critical factor when choosing a diode, it can be calculated from the equation below: Pdiode = (1 − Figure 5. External Bootstrap Diode VOUT ) × Iout × 0.3V VIN Note: 0.3V is the voltage drop across the schottky diode. A diode that can withstand this power dissipation must be chosen. PC Board Layout This is a high switching frequency converter. Hence attention must be paid to the switching currents interference in the layout. Switching current from one power device to another can generate voltage transients across the impedances of the interconnecting bond wires and circuit traces. These interconnecting impedances should be minimized by using wide, short printed circuit traces. The input capacitor needs to be as close as possible to the IN and GND pins. The external feedback resistors should be placed next to the FB pin. AP5100 Document number: DS32130 Rev. 1 - 2 10 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency Marking Information (1) SOT26 ( Top View ) 5 4 7 6 XX Y W X 1 Part Number AP5100W Package Information 2 3 XX : Identification Code Y : Year 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : A~Z : Green Package SOT26 Identification Code AJ (All Dimensions in mm) (1) Package type: SOT26 AP5100 Rev. 1 Document number: DS32130 Rev. 1 - 2 11 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated AP5100 1.2A Step-Down Converter with 1.4MHz Switching Frequency IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2010, Diodes Incorporated www.diodes.com AP5100 Rev. 1 Document number: DS32130 Rev. 1 - 2 12 of 12 www.diodes.com MARCH 2010 © Diodes Incorporated