NBXSBA007 3.3 V, 240.00 MHz LVPECL Clock Oscillator The NBXSBA007, single frequency, crystal oscillator (XO) is designed to meet today’s requirements for 3.3 V LVPECL clock generation applications. The device uses a high Q fundamental crystal and Phase Lock Loop (PLL) multiplier to provide 240.00 MHz, ultra low jitter and phase noise LVPECL differential output. This device is a member of ON Semiconductor’s PureEdget clock family that provides accurate and precision clock solutions. Available in 5 mm x 7 mm SMD (CLCC) package on 16 mm tape and reel in quantities of 1,000. Features • • • • • • • • • LVPECL Differential Output Uses High Q Fundamental Mode Crystal and PLL Multiplier Ultra Low Jitter and Phase Noise − 0.4 ps (12 kHz − 20 MHz) Output Frequency − 240.00 MHz Hermetically Sealed Ceramic SMD Package RoHS Compliant Operating Range 3.3 V ±10% Total Frequency Stability − $50 PPM This is a Pb−Free Device Applications http://onsemi.com MARKING DIAGRAM 6 PIN CLCC LN SUFFIX CASE 848AB NBXSBA007 = NBXSBA007 (±50 PPM) 240 = Output Frequency (MHz) A = Assembly Location WL = Wafer Lot YY = Year WW = Work Week G = Pb−Free Package ORDERING INFORMATION Device • Networking NBXSBA007 240 AWLYYWWG Package Shipping† NBXSBA007LN1TAG CLCC−6 1000/Tape & Reel (Pb−Free) VDD 6 NBXSBA007LNHTAG CLCC−6 100/Tape & Reel (Pb−Free) CLK CLK 5 4 †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. PLL Clock Multiplier Crystal 1 OE 2 NC 3 GND Figure 1. Simplified Logic Diagram This document contains information on a product under development. ON Semiconductor reserves the right to change or discontinue this product without notice. © Semiconductor Components Industries, LLC, 2009 March, 2009 − Rev. 1 1 Publication Order Number: NBXSBA007/D NBXSBA007 OE 1 6 VDD NC 2 5 CLK GND 3 4 CLK Figure 2. Pin Connections (Top View) Table 1. PIN DESCRIPTION ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Pin No. Symbol I/O Description 1 OE LVTTL/LVCMOS Control Input 2 NC N/A No Connect. 3 GND Power Supply Ground 0 V 4 CLK LVPECL Output Non−Inverted Clock Output. Typically loaded with 50 W receiver termination resistor to VTT = VDD − 2 V. 5 CLK LVPECL Output Inverted Clock Output. Typically loaded with 50 W receiver termination resistor to VTT = VDD − 2 V. 6 VDD Power Supply Output Enable Pin. When left floating pin defaults to logic HIGH and output is active. See OE pin description Table 2. Positive power supply voltage. Voltage should not exceed 3.3 V ±10%. Table 2. OUTPUT ENABLE TRI−STATE FUNCTION OE Pin Output Pins Open Active HIGH Level Active LOW Level High Z Table 3. ATTRIBUTES Characteristic Value Internal Default State Resistor ESD Protection 170 kW Human Body Model Machine Model 2 kV 200 V Meets or Exceeds JEDEC Standard EIA/JESD78 IC Latchup Test 1. For additional Moisture Sensitivity information, refer to Application Note AND8003/D. Table 4. MAXIMUM RATINGS Symbol Rating Units VDD Positive Power Supply Parameter Condition 1 GND = 0 V Condition 2 4.6 V Iout LVPECL Output Current Continuous Surge 25 50 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −55 to +120 °C Tsol Wave Solder 260 °C See Figure 5 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. http://onsemi.com 2 NBXSBA007 Table 5. DC CHARACTERISTICS (VDD = 3.3 V ± 10%, GND = 0 V, TA = −40°C to +85°C) (Note 2) Symbol Characteristic Conditions Min. Typ. Max. Units 75 100 mA IDD Power Supply Current VIH OE Input HIGH Voltage 2000 VDD mV VIL OE Input LOW Voltage GND − 300 800 mV IIH Input HIGH Current OE FSEL −100 −100 +100 +100 mA IIL Input LOW Current OE FSEL −100 −100 +100 +100 mA VDD−1195 2105 VDD−945 2355 mV VDD = 3.3 V VDD−1945 1355 VDD−1600 1700 mV VDD = 3.3 V VOH VOL VOUTPP Output HIGH Voltage Output LOW Voltage Output Voltage Amplitude 680 mV NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 Ifpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Measurement taken with outputs terminated with 50 W to VDD − 2.0 V. See Figure 4. Table 6. AC CHARACTERISTICS (VDD = 3.3 V ± 10%, GND = 0 V, TA = −40°C to +85°C) (Note 3) Symbol Characteristic fCLKOUT Output Clock Frequency Df FNOISE Frequency Stability Phase−Noise Performance fCLKout = 240.00 MHz (See Figure 3) tjit(F) RMS Phase Jitter tjitter Cycle to Cycle, RMS Cycle to Cycle, Peak−to−Peak tOE/OD tDUTY_CYCLE Conditions Min. Typ. Max. 240.00 (Note 4) Units MHz ±50 ppm 100 Hz of Carrier −109 dBc/Hz 1 kHz of Carrier −125 dBc/Hz 10 kHz of Carrier −132 dBc/Hz 100 kHz of Carrier −132 dBc/Hz 1 MHz of Carrier −141 dBc/Hz 10 MHz of Carrier −161 dBc/Hz 12 kHz to 20 MHz 0.4 0.9 ps 1000 Cycles 1.5 8 ps 1000 Cycles 15 30 ps Period, RMS 10,000 Cycles 1 4 ps Period, Peak−to−Peak 10,000 Cycles 10 20 ps 200 ns 50 52 % Output Enable/Disable Time Output Clock Duty Cycle (Measured at Cross Point) 48 tR Output Rise Time (20% and 80%) 250 400 ps tF Output Fall Time (80% and 20%) 250 400 ps 1 5 ms 3 ppm 1 ppm tstart Start−up Time Aging 1st Year Every Year After 1st NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 Ifpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 3. Measurement taken with outputs terminated with 50 W to VDD − 2.0 V. See Figure 4. 4. Parameter guarantee 10 years aging. Includes initial stability at 25°C, shock, vibration, and first year aging. http://onsemi.com 3 NBXSBA007 Figure 3. Typical Phase Noise Plot Table 7. RELIABILITY COMPLIANCE ÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Parameter Standard Method Shock Mechanical MIL−STD−833, Method 2002, Condition B Solderability Mechanical MIL−STD−833, Method 2003 Vibration Mechanical MIL−STD−833, Method 2007, Condition A Solvent Resistance Mechanical MIL−STD−202, Method 215 Thermal Shock Environment MIL−STD−833, Method 1011, Condition A Moisture Level Sensitivity Environment MSL1 260°C per IPC/JEDEC J−STD−020D http://onsemi.com 4 NBXSBA007 NBXSBA007 Zo = 50 W Q D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VDD − 2.0 V Figure 4. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) temp. 260°C 20 − 40 sec. max. peak Temperature (°C) 260 6°C/sec. max. 3°C/sec. max. 217 ramp−up 175 150 cooling pre−heat reflow 60180 sec. Time 60150 sec. Figure 5. Recommended Reflow Soldering Profile http://onsemi.com 5 NBXSBA007 PACKAGE DIMENSIONS 6 PIN CLCC, 7x5, 2.54P CASE 848AB−01 ISSUE C A D 4X D1 0.15 C E2 TERMINAL 1 INDICATOR NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. B H E1 DIM A A1 A2 A3 b D D1 D2 D3 E E1 E2 E3 e H L R E D2 TOP VIEW A2 A3 0.10 C A SIDE VIEW A1 C 6.17 6.66 4.37 4.65 1.17 SOLDERING FOOTPRINT* 3 2 e 6X R 1.50 E3 0.10 C A B 0.05 C 0.08 1.30 MILLIMETERS NOM MAX 1.80 1.90 0.70 REF 0.36 REF 0.10 0.12 1.40 1.50 7.00 BSC 6.20 6.23 6.81 6.96 5.08 BSC 5.00 BSC 4.40 4.43 4.80 4.95 3.49 BSC 2.54 BSC 1.80 REF 1.27 1.37 0.70 REF SEATING PLANE D3 1 MIN 1.70 6X b 6 5 4 6X 5.06 L BOTTOM VIEW 2.54 PITCH 6X 1.50 DIMENSION: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. PureEdge is a trademark of Semiconductor Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NBXSBA007/D