NCV8504 Series Micropower 400 mA LDO Linear Regulators with DELAY, Adjustable RESET, and General Use Comparator The NCV8504 is a family of precision micropower voltage regulators. Their output current capability is 400 mA. The family has output voltage options for Adjustable, 2.5 V, 3.3 V and 5.0 V. The output voltage is accurate within ± 2.0% with a maximum dropout voltage of 0.6 V at 400 mA. Low quiescent current is a feature drawing only 100 µA with a 100 µA load. This part is ideal for any and all battery operated microprocessor equipment. Microprocessor control logic includes an active RESET (with DELAY). The active RESET circuit operates correctly at an output voltage as low as 1.0 V. The RESET function is activated during the power up sequence or during normal operation if the output voltage drops below the regulation limits. The reset threshold voltage can be decreased by the connection of external resistor divider to RADJ lead. The general use comparator (FLAG/Monitor) is referenced to a temperature stable voltage and provides 1 mA of drive current at its open collector output. The regulator is protected against reverse battery, short circuit, and thermal overload conditions. The device can withstand load dump transients making it suitable for use in automotive environments. The device has also been optimized for EMC conditions. Features • Output Voltage Options: Adjustable, 2.5 V, 3.3 V, 5.0 V • ± 2.0% Output • Low 100 µA Quiescent Current • Fixed or Adjustable Output Voltage • Active RESET • Adjustable Reset • 400 mA Output Current Capability • Fault Protection ♦ +60 V Peak Transient Voltage ♦ −15 V Reverse Voltage ♦ Short Circuit ♦ Thermal Overload • General Use Comparator • NCV Prefix for Automotive and Other Applications Requiring Site and Change Control Semiconductor Components Industries, LLC, 2004 January, 2004 − Rev. 14 1 http://onsemi.com MARKING DIAGRAM 16 16 1 SOIC 16 LEAD WIDE BODY EXPOSED PAD PDW SUFFIX CASE 751R NCV8504x AWLYYWW 1 x = Voltage Ratings as Indicated Below: A = Adjustable 2 = 2.5 V 3 = 3.3 V 5 = 5.0 V A = Assembly Location WL = Wafer Lot YY = Year WW = Work Week ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet. Publication Order Number: NCV8504/D NCV8504 Series PIN CONNECTIONS ADJUSTABLE OUTPUT 1 FIXED OUTPUT 1 16 FLAG RESET NC GND NC NC DELAY RADJ VADJ VOUT NC NC NC NC VIN MON SENSE VOUT NC NC NC NC VIN MON 16 FLAG RESET NC GND NC NC DELAY RADJ Monitor IQ VIN VOUT (VO) VDD 33 µF 10 µF RADJ NCV8504 DELAY RFLG 5.1 k Microprocessor VBAT SENSE (Fixed Output Only) RRST 5.1 k MON CDELAY VADJ (Adjustable Output Only) RESET FLAG I/O GND Figure 1. Application Diagram http://onsemi.com 2 I/O NCV8504 Series MAXIMUM RATINGS* Rating Value Unit −15 to 45 V Peak Transient Voltage (46 V Load Dump @ VIN = 14 V) 60 V Operating Voltage 45 V VOUT (DC) 16 V Voltage Range (RESET, FLAG, RADJ, DELAY) −0.3 to 10 V Input Voltage Range MON VADJ −0.3 to 10 −0.3 to 16 V V 4.0 200 kV V Junction Temperature, TJ −40 to +150 °C Storage Temperature, TS −55 to 150 °C 16 57 °C/W °C/W 240 peak (Note 2) °C VIN (DC) ESD Susceptibility (Human Body Model) (Machine Model) Package Thermal Resistance, SOW−16 E PAD: Junction−to−Case, RθJC Junction−to−Ambient, RθJA Lead Temperature Soldering: Reflow: (SMD styles only) (Note 1) 1. 60 second maximum above 183°C. 2. −5°C/+0°C allowable conditions. *The maximum package power dissipation must be observed. †During the voltage range which exceeds the maximum tested voltage of VIN, operation is assured, but not specified. Wider limits may apply. Thermal dissipation must be observed closely. ELECTRICAL CHARACTERISTICS (IOUT = 1.0 mA, −40°C ≤ TJ ≤ 150°C; VIN = dependent on voltage option (Note 3); unless otherwise specified.) Characteristic Test Conditions Min Typ Max Unit Output Stage Output Voltage for 2.5 V Option (VO) 6.5 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA 4.5 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA 2.450 2.425 2.5 2.5 2.550 2.575 V V Output Voltage for 3.3 V Option (VO) 7.3 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA 4.5 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA 3.234 3.201 3.3 3.3 3.366 3.399 V V Output Voltage for 5.0 V Option (VO) 9.0 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA 6.0 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA 4.90 4.85 5.0 5.0 5.10 5.15 V V Output Voltage for Adjustable Option (VO) VOUT = VADJ (Unity Gain) 6.5 V < VIN < 16 V, 1.0 mA < IOUT < 400 mA 4.5 V < VIN < 26 V, 1.0 mA < IOUT < 400 mA 1.274 1.261 1.300 1.306 1.326 1.339 V V Dropout Voltage (VIN − VOUT) (5.0 V and Adj. > 5.0 V Options Only) IOUT = 400 mA IOUT = 1.0 mA − − 400 30 600 150 mV mV Load Regulation VIN = 14 V, 5.0 mA ≤ IOUT ≤ 400 mA −30 5.0 30 mV Line Regulation (2.5 V, 3.3 V, and Adjustable Options) 4.5 V < VIN < 26 V, IOUT = 1.0 mA − 5.0 25 mV Line Regulation (5.0 V Option) 6.0 V < VIN < 26 V, IOUT = 1.0 mA − 5.0 25 mV Quiescent Current, (IQ) Active Mode IOUT = 100 µA, VIN = 12 V, Delay = 3.0 V, MON = 3.0 V IOUT = 75 mA, VIN = 14 V, Delay = 3.0 V, MON = 3.0 V IOUT ≤ 400 mA, VIN = 14 V, Delay = 3.0 V, MON = 3.0 V − − − 100 2.5 25 150 5.0 45 µA mA mA − 425 800 − mA Current Limit Short Circuit Output Current VOUT = 0 V 100 500 − mA Thermal Shutdown (Guaranteed by Design) 150 180 − °C 3. Voltage range specified in the Output Stage of the Electrical Characteristics in boldface type. http://onsemi.com 3 NCV8504 Series ELECTRICAL CHARACTERISTICS (continued) (IOUT = 1.0 mA, −40°C ≤ TJ ≤ 150°C; VIN = dependent on voltage option (Note 4); unless otherwise specified.) Characteristic Test Conditions Min Typ Max Unit 2.35 2.30 25 − − − 1.0 × VO − − V V mV 3.10 3.00 35 − − − 1.0 × VO − − V V mV 4.70 4.60 50 − − − 1.0 × VO − − V V mV 1.22 1.19 10 − − − 1.0 × VO − − V V mV − 0.1 0.4 V Reset Function (RESET) RESET Threshold for 2.5 V Option HIGH (VRH) LOW (VRL) Hysteresis VIN = 4.5 V (Note 5) (Note 6) VOUT Increasing VOUT Decreasing RESET Threshold for 3.3 V Option HIGH (VRH) LOW (VRL) Hysteresis VIN = 4.5 V (Note 5) (Note 6) VOUT Increasing VOUT Decreasing RESET Threshold for 5.0 V Option HIGH (VRH) LOW (VRL) Hysteresis VIN = 6.0 V (Note 6) VOUT Increasing VOUT Decreasing RESET Threshold for Adjustable Option HIGH (VRH) LOW (VRL) Hysteresis VIN = 4.5 V (Note 5) (Note 6) VOUT Increasing VOUT Decreasing Output Voltage Low (VRLO) VIN = Minimum (Note 6) (Note 7) 1.0 V ≤ VOUT ≤ VRL, RRESET = 5.1 k DELAY Switching Threshold (VDT) (2.5 V, 3.3 V, and 5.0 V Options) VIN = Minimum (Note 6) (Note 7) 1.4 1.8 2.2 V DELAY Switching Threshold (VDT) (Adjustable Option) VIN = Minimum (Note 6) (Note 7) 1.0 1.3 1.6 V DELAY Low Voltage VIN = Minimum (Note 6) (Note 7) VOUT < RESET Threshold Low(min) − − 0.2 V DELAY Charge Current VIN = Minimum (Note 6) (Note 7) DELAY = 1.0 V, VOUT > VRH 2.5 4.0 5.5 µA DELAY Discharge Current VIN = Minimum (Note 6) (Note 7) DELAY = 1.0 V, VOUT < VRL 5.0 − − mA Reset Adjust Switching Voltage (VR(ADJ)) Hysteresis VIN = Minimum (Note 6) (Note 7) Increasing and Decreasing 1.16 20 1.25 50 1.34 100 V mV Monitor Threshold Increasing and Decreasing, VIN = Minimum (Note 6) (Note 7) 1.22 1.29 1.36 V Hysteresis VIN = Minimum (Note 6) (Note 7) 10 35 75 mV Input Current MON = 2.0 V −1.0 0.1 1.0 µA Output Saturation Voltage MON = 0 V, IFLAG = 1.0 mA, VIN = Minimum (Note 6) (Note 7) − 0.1 0.4 V −0.5 − 0.5 µA FLAG/Monitor Voltage Adjust (Adjustable Output only) Input Current VADJ = 1.25 V 4. Voltage range specified in the Output Stage of the Electrical Characteristics in boldface type. 5. For VIN ≤ 4.5 V, a RESET = Low may occur with the output in regulation. 6. Part is guaranteed by design to meet specification over the entire VIN voltage range, but is production tested only at the specified VIN voltage. 7. Minimum VIN = 4.5 V for 2.5 V, 3.3 V, and Adjustable options. Minimum VIN = 6.0 V for 5.0 V option. http://onsemi.com 4 NCV8504 Series PACKAGE PIN DESCRIPTION, ADJUSTABLE OUTPUT Pin Number Pin Symbol 1 VADJ Voltage Adjust. A resistor divider from VOUT to this lead sets the output voltage. 2 VOUT ±2.0%, 400 mA output. 3−6, 11, 12, 14 NC No connection. 7 VIN Input Voltage. 8 MON Monitor. Input to comparator. If not needed connect to VOUT. 9 RADJ Reset Adjust. If not needed connect to ground. 10 DELAY 13 GND 15 RESET Active reset (accurate to VOUT ≥ 1.0 V) 16 FLAG Open collector output from comparator. NOTE: Function Timing capacitor for RESET function. Ground. All GND leads must be connected to Ground. Tentative pinout for SOW−16 E Pad. PACKAGE PIN DESCRIPTION, FIXED OUTPUT Pin Number Pin Symbol 1 SENSE 2 VOUT 3−6, 11, 12, 14 NC No connection. 7 VIN Input Voltage. 8 MON Monitor. Input to comparator. If not needed connect to VOUT. 9 RADJ Reset Adjust. If not needed connect to ground. 10 DELAY 13 GND 15 RESET Active reset (accurate to VOUT ≥ 1.0 V) 16 FLAG Open collector output from comparator. NOTE: Function Kelvin connection which allows remote sensing of output voltage for improved regulation. If remote sensing is not desired, connect to VOUT. ±2.0%, 400 mA output. Timing capacitor for RESET function. Ground. All GND leads must be connected to Ground. Tentative pinout for SOW−16 E Pad. http://onsemi.com 5 NCV8504 Series VOUT VIN Current Source (Circuit Bias) SENSE IBIAS Current Limit Sense RADJ + + − IBIAS VBG − 18 mV RESET + − 1.8 V (Fixed Versions) 1.3 V (Adjustable Version) Error Amplifier VBG + Fixed Versions only − Thermal Protection 4.0 µA DELAY IBIAS Bandgap Reference VBG VADJ VBG − Figure 2. Block Diagram http://onsemi.com 6 GND IBIAS + MON 15 k Adjustable Version only FLAG NCV8504 Series TYPICAL PERFORMANCE CHARACTERISTICS 5.10 3.35 Vout, OUTPUT VOLTAGE (V) 5.08 5.06 Vout, OUTPUT VOLTAGE (V) VOUT = 5.0 V VIN = 14 V IOUT = 5.0 mA 5.04 5.02 5.00 4.98 4.96 4.94 VOUT = 3.3 V VIN = 14 V IOUT = 5.0 mA 3.33 3.31 3.29 3.27 3.25 4.92 4.90 −40 −20 0 3.23 −40 −20 20 40 60 80 100 120 140 160 TEMPERATURE (°C) Figure 3. 5 V Output Voltage vs Temperature 20 40 60 80 100 120 140 160 TEMPERATURE (°C) Figure 4. 3.3 V Output Voltage vs Temperature 700 2.55 2.53 DROPOUT VOLTAGE (mV) VOUT = 2.5 V VIN = 14 V IOUT = 5.0 mA 2.54 Vout, OUTPUT VOLTAGE (V) 0 2.52 2.51 2.50 2.49 2.48 2.47 2.46 600 500 125 °C 400 25 °C 300 200 −40 °C 100 5 V and Adj. > 5 V options only 2.45 −40 −20 0 0 20 40 60 80 100 120 140 160 TEMPERATURE (°C) 0 Figure 5. 2.5 V Output Voltage vs Temperature 100 100 150 200 250 300 Iout, OUTPUT CURRENT (mA) 350 400 Figure 6. Dropout Voltage vs Output Current 100 5.0 V Unstable Region 50 CVOUT = 33 F* Unstable Region 3.3 V 10 10 ESR () ESR () 2.5 V 1.0 Stable Region 1.0 Stable Region Unstable Region 0.1 VIN = 14 V CVOUT = 10 F 0.01 CVOUT = 0.1 F 0 50 100 150 200 250 300 Iout, OUTPUT CURRENT (mA) 350 0.1 400 *There is no unstable lower region for the 33 F capacitor 0 Figure 7. Output Stability with Output Voltage Change 50 Figure 8. Output Stability with Output Capacitor Change http://onsemi.com 7 5 V version 100 150 200 250 300 Iout, OUTPUT CURRENT (mA) 350 400 NCV8504 Series TYPICAL PERFORMANCE CHARACTERISTICS 60 +125°C 1.8 IQ, QUIESCENT CURRENT (mA) IQ, QUIESCENT CURRENT (mA) 2.0 +25°C 1.6 −40°C 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 5 10 40 15 20 25 30 35 IOUT, OUTPUT CURRENT (mA) 45 +25°C 40 −40°C 30 20 10 0 50 +125°C 50 0 Figure 9. Quiescent Current vs Output Current T = 25°C IQ, QUIESCENT CURRENT (A) IQ, QUIESCENT CURRENT (mA) 140 T = 25°C 10 8 6 4 Iout = 100 mA 2 Iout = 50 mA Iout = 10 mA 0 6 8 10 12 14 16 18 20 VIN, INPUT VOLTAGE (V) 22 24 100 150 200 250 300 350 400 450 500 IOUT, OUTPUT CURRENT (mA) Figure 10. Quiescent Current vs Output Current 12 Iout = 200 mA 50 120 100 80 60 40 20 0 26 Figure 11. Quiescent Current vs Input Voltage Iout = 100 A 6 8 10 12 14 16 18 20 VIN, INPUT VOLTAGE (V) 22 24 26 Figure 12. Quiescent Current vs Input Voltage http://onsemi.com 8 NCV8504 Series CIRCUIT DESCRIPTION The DELAY lead provides source current (typically 4.0 µA) to the external DELAY capacitor during the following proceedings: 1. During Power Up (once the regulation threshold has been verified). 2. After a reset event has occurred and the device is back in regulation. The DELAY capacitor is discharged when the regulation (RESET threshold) has been violated. This is a latched incident. The capacitor will fully discharge and wait for the device to regulate before going through the delay time event again. REGULATOR CONTROL FUNCTIONS The NCV8504 contains the microprocessor compatible control function RESET (Figure 13). VIN RESET Threshold VOUT DELAY DELAY Threshold (VDT) RESET Td FLAG/Monitor Comparator Td A general use comparator is included whose positive input terminal is tied to the on−chip bandgap voltage reference. This provides a very temperature stable referenced comparator with versatile use in any system. The trip point can be programmed externally using a resistor divider to the input monitor (MON) (Figure 15). The typical threshold is 1.29 V on the MON pin. Figure 13. Reset and Delay Circuit Wave Forms RESET Function A RESET signal (low voltage) is generated as the IC powers up until VOUT is within 1.5% of the regulated output voltage, or when VOUT drops out of regulation,and is lower than 4.0% below the regulated output voltage. Hysteresis is included in the function to minimize oscillations. The RESET output is an open collector NPN transistor, controlled by a low voltage detection circuit. The circuit is functionally independent of the rest of the IC thereby guaranteeing that the RESET signal is valid for VOUT as low as 1.0 V. VMON VBAT The reset threshold can be made lower by connecting an external resistor divider to the RADJ lead from the VOUT lead, as displayed in Figure 14. This lead is grounded to select the default value of 4.6 V (on the 5.0 V option). NCV8504 DELAY RRST RESET MON FLAG RADJ RESET DELAY GND µP COUT I/O RESET Figure 15. Flag/Monitor Function to µP and System Power VOUT RADJ VCC NCV8504 Adjustable Reset Function VR(ADJ) VOUT VIN Voltage Adjust Figure 16 shows the device setup for a user configurable output voltage. The feedback to the VADJ pin is taken from a voltage divider referenced to the output voltage. The loop is balanced around the Unity Gain threshold (1.30 V typical). COUT to µP and RESET Port ≈5.0 V VOUT NCV8504 CDELAY VADJ 15 k 1.28 V 5.1 k Figure 14. Adjustable RESET DELAY Function The reset delay circuit provides a programmable (by external capacitor) delay on the RESET output lead. Figure 16. Adjustable Output Voltage http://onsemi.com 9 COUT NCV8504 Series APPLICATION NOTES FLAG MONITOR Figure 17 shows the FLAG Monitor waveforms as a result of the circuit depicted in Figure 15. As the input voltage falls (VMON), the Monitor threshold is crossed. This causes the voltage on the FLAG output to go low. VIN VOUT CIN* 0.1 µF NCV8504 COUT** 33 µF RRST RESET VMON *CIN required if regulator is located far from the power supply filter **COUT required for stability. Capacitor must operate at minimum temperature expected MON Figure 18. Test and Application Circuit Showing Output Compensation Flag Monitor Ref. Voltage CALCULATING POWER DISSIPATION IN A SINGLE OUTPUT LINEAR REGULATOR The maximum power dissipation for a single output regulator (Figure 19) is: FLAG PD(max) [VIN(max) VOUT(min)] IOUT(max) Figure 17. FLAG Monitor Circuit Waveform where: VIN(max) is the maximum input voltage, VOUT(min) is the minimum output voltage, IOUT(max) is the maximum output current for the application, and IQ is the quiescent current the regulator consumes at IOUT(max). Once the value of PD(max) is known, the maximum permissible value of RJA can be calculated: SETTING THE DELAY TIME The delay time is controlled by the Reset Delay Low Voltage, Delay Switching Threshold, and the Delay Charge Current. The delay follows the equation: tDELAY [CDELAY(Vdt Reset Delay Low Voltage)] Delay Charge Current Example: Using CDELAY = 33 nF. Assume reset Delay Low Voltage = 0. Use the typical value for Vdt = 1.8 V (2.5 V, 3.3 V, and 5.0 V options). Use the typical value for Delay Charge Current = 4.2 µA. tDELAY (1) VIN(max)IQ T RJA 150°C A PD (2) The value of RJA can then be compared with those in the package section of the data sheet. Those packages with RJA’s less than the calculated value in equation 2 will keep the die temperature below 150°C. In some cases, none of the packages will be sufficient to dissipate the heat generated by the IC, and an external heatsink will be required. [33 nF(1.8 0)] 14 ms 4.2 A STABILITY CONSIDERATIONS The output or compensation capacitor helps determine three main characteristics of a linear regulator: start−up delay, load transient response and loop stability. The capacitor value and type should be based on cost, availability, size and temperature constraints. A tantalum or aluminum electrolytic capacitor is best, since a film or ceramic capacitor with almost zero ESR can cause instability. The aluminum electrolytic capacitor is the least expensive solution, but, if the circuit operates at low temperatures (−25°C to −40°C), both the value and ESR of the capacitor will vary considerably. The capacitor manufacturers data sheet usually provides this information. The value for the output capacitor COUT shown in Figure 18 should work for most applications, however it is not necessarily the optimized solution. IOUT IIN VIN SMART REGULATOR VOUT } Control Features IQ Figure 19. Single Output Regulator with Key Performance Parameters Labeled http://onsemi.com 10 NCV8504 Series Thermal Resistance, Junction to Ambient, RJA, (°C/W) 100 HEAT SINKS A heat sink effectively increases the surface area of the package to improve the flow of heat away from the IC and into the surrounding air. Each material in the heat flow path between the IC and the outside environment will have a thermal resistance. Like series electrical resistances, these resistances are summed to determine the value of RJA: 90 80 70 60 RJA RJC RCS RSA 50 40 0 200 400 600 Copper Area (mm2) (3) where: RJC = the junction−to−case thermal resistance, RCS = the case−to−heatsink thermal resistance, and RSA = the heatsink−to−ambient thermal resistance. RJC appears in the package section of the data sheet. Like RJA, it too is a function of package type. RCS and RSA are functions of the package type, heatsink and the interface between them. These values appear in heat sink data sheets of heat sink manufacturers. 800 Figure 20. 16 Lead SOW (Exposed Pad), JA as a Function of the Pad Copper Area (2 oz. Cu Thickness), Board Material = 0.0625 G−10/R−4 http://onsemi.com 11 NCV8504 Series ORDERING INFORMATION Device Output Voltage Package NCV8504PWADJ NCV8504PWADJR2 47 Units/Rail Adjustable 1000 Tape & Reel NCV8504PW25 NCV8504PW25R2 47 Units/Rail 25V 2.5 1000 Tape & Reel SOW 16 Exposed Pad SOW−16 NCV8504PW33 NCV8504PW33R2 33V 3.3 47 Units/Rail 1000 Tape & Reel NCV8504PW50 NCV8504PW50R2 Shipping 47 Units/Rail 50V 5.0 1000 Tape & Reel http://onsemi.com 12 NCV8504 Series PACKAGE DIMENSIONS SOIC 16 LEAD WIDE BODY EXPOSED PAD PDW SUFFIX CASE 751R−02 ISSUE A −U− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751R−01 OBSOLETE, NEW STANDARD 751R−02. A M 16 9 P 0.25 (0.010) M W M B 1 R x 45 8 −W− G PIN 1 I.D. 14 PL DETAIL E TOP SIDE C F −T− 0.10 (0.004) T K D 16 PL 0.25 (0.010) T U M SEATING PLANE W S S J DETAIL E H EXPOSED PAD 1 8 L 16 9 BACK SIDE http://onsemi.com 13 DIM A B C D F G H J K L M P R MILLIMETERS MIN MAX 10.15 10.45 7.40 7.60 2.35 2.65 0.35 0.49 0.50 0.90 1.27 BSC 3.76 3.86 0.25 0.32 0.10 0.25 4.58 4.78 0 7 10.05 10.55 0.25 0.75 INCHES MIN MAX 0.400 0.411 0.292 0.299 0.093 0.104 0.014 0.019 0.020 0.035 0.050 BSC 0.148 0.152 0.010 0.012 0.004 0.009 0.180 0.188 0 7 0.395 0.415 0.010 0.029 NCV8504 Series SMART REGULATOR is a registered trademark of Semiconductor Components Industries, LLC (SCILLIC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 14 For additional information, please contact your local Sales Representative. NCV8504/D