MC74AC04, MC74ACT04 Hex Inverter • Outputs Source/Sink 24 mA • ′ACT04 Has TTL Compatible Inputs VCC 14 http://onsemi.com 13 12 11 10 9 8 PDIP–14 N SUFFIX CASE 646 14 1 1 2 3 4 5 6 7 SO–14 D SUFFIX CASE 751A 14 GND 1 Figure 1. Pinout: 14–Lead Packages Conductors (Top View) 14 1 TSSOP–14 DT SUFFIX CASE 948G MAXIMUM RATINGS* Rating Symbol Value Unit DC Supply Voltage (Referenced to GND) VCC –0.5 to +7.0 V DC Input Voltage (Referenced to GND) Vin –0.5 to VCC +0.5 V DC Output Voltage (Referenced to GND) Vout –0.5 to VCC +0.5 V Iin ±20 Iout 14 1 DC Input Current, per Pin DC Output Sink/Source Current, per Pin EIAJ–14 M SUFFIX CASE 965 ORDERING INFORMATION Device Package Shipping mA MC74AC04N PDIP–14 25 Units/Rail ±50 mA MC74ACT04N PDIP–14 25 Units/Rail DC VCC or GND Current per Output Pin ICC ±50 mA MC74AC04D SOIC–14 55 Units/Rail Storage Temperature Tstg –65 to +150 °C MC74AC04DR2 SOIC–14 2500 Tape & Reel MC74ACT04D SOIC–14 55 Units/Rail MC74ACT04DR2 SOIC–14 2500 Tape & Reel MC74AC04DT TSSOP–14 96 Units/Rail MC74AC04DTR2 TSSOP–14 2500 Tape & Reel MC74ACT04DT TSSOP–14 MC74ACT04DTR2 TSSOP–14 2500 Tape & Reel *Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. 96 Units/Rail MC74AC04M EIAJ–14 50 Units/Rail MC74AC04MEL EIAJ–14 2000 Tape & Reel MC74ACT04M EIAJ–14 50 Units/Rail MC74ACT04MEL EIAJ–14 2000 Tape & Reel DEVICE MARKING INFORMATION See general marking information in the device marking section on page 5 of this data sheet. Semiconductor Components Industries, LLC, 2001 May, 2001 – Rev. 5 1 Publication Order Number: MC74AC04/D MC74AC04, MC74ACT04 RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage Vin, Vout DC Input Voltage, Output Voltage (Ref. to GND) tr, tf Input Rise and Fall Time (Note 1) ′AC Devices except Schmitt Inputs Min Typ Max Unit ′AC 2.0 5.0 6.0 ′ACT 4.5 5.0 5.5 0 – VCC VCC @ 3.0 V – 150 – VCC @ 4.5 V – 40 – VCC @ 5.5 V – 25 – VCC @ 4.5 V – 10 – VCC @ 5.5 V – 8.0 – – – 140 °C –40 25 85 °C V V ns/V tr, tf In ut Rise and Fall Time (Note 2) Input ′ACT Devices except Schmitt Inputs TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range IOH Output Current – High – – –24 mA IOL Output Current – Low – – 24 mA ns/V 1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. DC CHARACTERISTICS Symbol Parameter VCC (V) 74AC 74AC TA = +25°C TA = –40°C to +85°C Typ VIH VIL VOH VOL Guaranteed Limits 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC – 0.1 V Maximum Low Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC – 0.1 V Minimum High g Level Output Voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 V 3.0 4.5 5.5 – – – 2.56 3.86 4.86 2.46 3.76 4.76 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 5.5 – – – 0.36 0.36 0.36 0.44 0.44 0.44 55 5.5 – ±0 1 ±0.1 5.5 – 5.5 55 5.5 Maximum Low Level Output Voltage Maximum Input Leakage Current IOLD †Minimum Dynamic O t t Current Output C t ICC Conditions Minimum High g Level Input Voltage IIN IOHD Unit Maximum Q Quiescent Supply Current V *VIN = VIL or VIH –12 mA IOH –24 mA –24 mA IOUT = 50 µA V V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA ±1 0 ±1.0 µA VI = VCC, GND – 75 mA VOLD = 1.65 V Max – – –75 mA VOHD = 3.85 V Min – 40 4.0 40 µA VIN = VCC or GND *All outputs loaded; thresholds on input associated with output under test. †Maximum test duration 2.0 ms, one output loaded at a time. NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC. http://onsemi.com 2 IOUT = –50 µA MC74AC04, MC74ACT04 AC CHARACTERISTICS (For Figures and Waveforms – See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) Symbol VCC* (V) Parameter 74AC 74AC TA = +25°C CL = 50 pF TA = –40°C to +85°C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation Delay 3.3 5.0 1.5 1.5 4.5 4.0 9.0 7.0 1.0 1.0 10 7.5 ns 3–5 tPHL Propagation Delay 3.3 5.0 1.5 1.5 4.5 3.5 8.5 6.5 1.0 1.0 9.5 7.0 ns 3–5 *Voltage Range 3.3 V is 3.3 V ±0.3 V. Voltage Range 5.0 V is 5.0 V ±0.5 V. DC CHARACTERISTICS Symbol Parameter VCC (V) 74ACT 74ACT TA = +25°C TA = –40°C to +85°C Typ Guaranteed Limits Unit Conditions VIH Minimum High g Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC – 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC – 0.1 V VOH Minimum High g Level Output Voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 V 4.5 5.5 – – 3.86 4.86 3.76 4.76 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 4.5 5.5 – – 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH 24 mA IOL 24 mA VOL Maximum Low Level Output Voltage V V IOUT = –50 µA *VIN = VIL or VIH –24 mA IOH –24 mA IOUT = 50 µA IIN Maximum Input Leakage Current 55 5.5 – ±0 1 ±0.1 ±1 0 ±1.0 µA VI = VCC, GND ∆ICCT Additional Max. ICC/Input 5.5 0.6 – 1.5 mA VI = VCC – 2.1 V IOLD †Minimum Dynamic O t t Current Output C t 5.5 – – 75 mA VOLD = 1.65 V Max 5.5 – – –75 mA VOHD = 3.85 V Min 55 5.5 – 40 4.0 40 µA VIN = VCC or GND IOHD ICC Maximum Q Quiescent Supply Current *All outputs loaded; thresholds on input associated with output under test. †Maximum test duration 2.0 ms, one output loaded at a time. http://onsemi.com 3 MC74AC04, MC74ACT04 AC CHARACTERISTICS (For Figures and Waveforms – See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) Symbol VCC* (V) Parameter 74ACT 74ACT TA = +25°C CL = 50 pF TA = –40°C to +85°C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation Delay 5.0 1.5 8.5 1.0 9.0 ns 3–6 tPHL Propagation Delay 5.0 1.5 8.0 1.0 8.5 ns 3–6 *Voltage Range 5.0 V is 5.0 V ±0.5 V. CAPACITANCE Symbol Parameter Value Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 30 pF VCC = 5.0 V http://onsemi.com 4 MC74AC04, MC74ACT04 MARKING DIAGRAMS PDIP–14 SO–14 TSSOP–14 EIAJ–14 MC74AC04N AWLYYWW AC04 AWLYWW AC 04 ALYW 74AC04 ALYW MC74ACT04N AWLYYWW ACT04 AWLYWW ACT 04 ALYW 74ACT04 ALYW A WL, L YY, Y WW, W = Assembly Location = Wafer Lot = Year = Work Week http://onsemi.com 5 MC74AC04, MC74ACT04 PACKAGE DIMENSIONS PDIP–14 N SUFFIX 14 PIN PLASTIC DIP PACKAGE CASE 646–06 ISSUE M 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. 8 B 1 7 A F DIM A B C D F G H J K L M N L N C –T– SEATING PLANE J K H D 14 PL G 0.13 (0.005) M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. –A– 8 –B– 1 P 7 PL 0.25 (0.010) 7 G M B M F R X 45 C –T– SEATING PLANE D 14 PL 0.25 (0.010) M T B J M K S A MILLIMETERS MIN MAX 18.16 18.80 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --10 0.38 1.01 M SO–14 D SUFFIX 14 PIN PLASTIC SOIC PACKAGE CASE 751A–03 ISSUE F 14 INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --10 0.015 0.039 S http://onsemi.com 6 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0 7 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.228 0.244 0.010 0.019 MC74AC04, MC74ACT04 PACKAGE DIMENSIONS TSSOP–14 DT SUFFIX 14 PIN PLASTIC TSSOP PACKAGE CASE 948G–01 ISSUE O NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S N 2X 14 L/2 0.25 (0.010) 8 M B –U– L PIN 1 IDENT. F 7 1 0.15 (0.006) T U N S DETAIL E K A –V– ÇÇÇ ÉÉ ÇÇÇ ÉÉ K1 J J1 DIM A B C D F G H J J1 K K1 L M SECTION N–N –W– C 0.10 (0.004) –T– SEATING PLANE H G D DETAIL E EIAJ–14 M SUFFIX 14 PIN PLASTIC EIAJ PACKAGE CASE 965–01 ISSUE O 14 LE 8 Q1 E HE L 7 1 M DETAIL P Z D VIEW P A e c b 0.13 (0.005) A1 M 0.10 (0.004) http://onsemi.com 7 MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.50 0.60 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0 8 INCHES MIN MAX 0.193 0.200 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.020 0.024 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE 0.50 LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 0 10 0.70 0.90 --1.42 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 0 10 0.028 0.035 --0.056 MC74AC04, MC74ACT04 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800–282–9855 Toll Free USA/Canada http://onsemi.com 8 MC74AC04/D