USB Downstream Port Terminator PACUSB-D1/D2/D3 Features Product Description • The PACUSB-D1/D2/D3 is a single-channel USB downstream-port termination network. It integrates EMI/RFI filter components R1 and C1, as recommended by the USB specification as well as the required 15kW pull-down resistors (R2) to GND. In addition, PACUSB-D1/D2/D3 provides a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The device pins will safely dissipate ESD strikes of +15kV, exceeding the maximum requirements of the IEC 61000-4-2 international standard. Using the MIL-STD-883D (Method 3015) specification for Human Body Model (HBM) ESD, all pins are protected from contact discharges to +20kV. • • • • • • A low-capacitance USB downstream port terminator, EMI filter, and transient over-voltage (ESD) protector in a single surface-mounted package ESD protection to +20kV contact discharge, per MIL-STD-883D, Method 3015 ESD protection to +15kV contact discharge, per IEC 61000-4-2 International Standard Compact SOT23-5 and SC70-5 package options save board space and lower manufacturing costs compared to discrete solutions Capacitors matched to a precision exceeding the USB specification Pin-compatible with ST Microelectronics USBDFxxW5 USB Downstream Port Terminator Lead-free versions available Applications • • • • • ESD protection and termination of USB downstream ports Desktop PCs Notebooks Set-top boxes USB hubs ©2010 SCILLC. All rights reserved. June 2010 – Rev. 2 There are three options for the value of the series resistor R1: 15Ω, 22Ω, and 33Ω. This series resistance, plus the USB driver output resistance, must be close to the USB cable’s characteristic impedance of 45Ω (each side) to minimize transmission line reflections. The PACUSB-D1/D2/D3 is manufactured in a 5-pin SC70 or a 5-pin SOT23 package and is available with optional lead-free finishing.. Publication Order Number: PACUSB-D1/D2/D3/D PACUSB-D1/D2/D3 Electrical•Schematic PIN DESCRIPTIONS PINS NAME DESCRIPTION 1 D+ CNTR 2 GND 3 D- CNTR D- Data to the USB controller circuitry 4 D- CONN D- Data to the USB connector 5 D+ CONN D+ Data to the USB connector D+ Data to the USB controller circuitry Ground Pin Rev. 2 | Page 2 of 10 | www.onsemi.com PACUSB-D1/D2/D3 Ordering Information PART NUMBERING INFORMATION Standard Finish Lead-free Finish Pins R1 Value Package Ordering Part 1 Number Part Marking Ordering Part 1 Number Part Marking 5 15 Ω SOT23-5 PACUSB-D2Y5 UDF2 PACUSB-D2Y5R DF2R 22 Ω PACUSB-D3Y5 UDF3 PACUSB-D3Y5R DF3R 33 Ω PACUSB-D1Y5 UDF1 PACUSB-D1Y5R DF1R PACUSB-D2YB5 DF2 PACUSB-D2YB5R F2R 22 Ω PACUSB-D3YB5 DF3 PACUSB-D3YB5R F3R 33 Ω PACUSB-D1YB5 DF1 PACUSB-D1YB5R F1R 15 Ω 5 SC70-5 Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS -65 to +150 °C Power Dissipation per Resistor 100 mW Package Power Dissipation 200 mW 6 V RATING UNITS -40 to +85 °C Storage Temperature Range Voltage on any pin (DC) STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Rev. 2 | Page 3 of 10 | www.onsemi.com PACUSB-D1/D2/D3 ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE 1) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS R1 Resistance of R1 Resistor (PACUSB-D2Y5/Y5R, -D2YB5/YB5R) TA = 25°C 12 15 18 Ω R1 Resistance of R1 Resistor (PACUSB-D3Y5/Y5R, -D3YB5/YB5R) TA = 25°C 17.6 22 26.4 Ω R1 Resistance of R1 Resistor (PACUSB-D1Y5/Y5R, -D1YB5/YB5R) TA = 25°C 26.4 33 39.6 Ω R2 Resistance of R2 Resistor TA = 25°C TCR Temperature Coefficient of Resistance Note 1 Capacitance of C1 Capacitor 0 VDC; 30 mVAC; 1MHz; 25°C 37.6 47 56.4 pF 2.5 VDC; 30 mVAC; 1MHz; 25°C 25.6 32 38.4 pF +2 % 100 nA C1 TOLCM Matching Tolerance of C1 Capacitors 1MHz; 25°C ILEAK Diode Leakage Current to GND Measured at 3.3 VDC, 25°C VRB Diode Reverse Bias Voltage ILOAD = 10μA; TA = 25°C 5.5 VSIG Signal Voltage: Positive Clamp Negative Clamp ILOAD = 10mA; TA = 25°C ILOAD = 10mA; TA = 25°C 5.6 -0.4 VESD kΩ +1300 ppm/° C 1 V 6.8 -0.8 9.0 -1.5 V V In-system ESD Withstand Voltage MIL-STD-883D, Method 3015 (HBM) IEC 61000-4-2 Contact Discharge VCL 15 Clamping voltage under ESD discharge Pins 1, 3; Notes 2 and 3 Pins 4, 5; Note 2 Pins 4, 5; Notes 2 +4 +20 kV kV +15 kV MIL-STD-883D, Method 3015 +8kV; Note 4 12 V MIL-STD-883D, Method 3015 8kV; Note 4 -7 V Note 1: Electrical operating characteristics guaranteed over standard operating conditions unless specified otherwise. Note 2: ESD voltage applied to pins with respect to GND, one at a time; unused pins are left open. Note 3: Pins 1 and 3 are not connected to the USB port connector, and therefore are not exposed to external ESD hazards. Thus, they do not require the high ESD protection levels provided for pins 4 and 5. Note 4: ESD Clamping Voltage is measured at the opposite end of R1 from the pin to which the ESD discharge is applied (e.g., if ESD is applied to pin 6, then the clamping voltage is measured at pin 1). Rev. 2 | Page 4 of 10 | www.onsemi.com PACUSB-D1/D2/D3 Performance Information Capacitance vs. Voltage The C1 capacitance value as a function of DC voltage across it is presented in Figure 1. The curve is normalized to a capacitance of 1.0 capacitance units at 2.5 VDC. Figure 1. Diode Capacitance vs. DC Voltage (Normalized) Insertion Loss vs. Frequency Characteristics Figure 2. Insertion Loss vs. Frequency Performance Curve, PACUSB-D1(SOT23-6) Rev. 2 | Page 5 of 10 | www.onsemi.com PACUSB-D1/D2/D3 Performance Information (cont’d) Figure 3. Insertion Loss vs. Frequency Performance Curve, PACUSB-D2(SOT23- 6) Figure 4. Insertion Loss vs. Frequency Performance Curve, PACUSB-D3(SOT23-6) Rev. 2 | Page 6 of 10 | www.onsemi.com PACUSB-D1/D2/D3 Application Information The PACUSB-D1/D2/D3 provides a complete interface for a single downstream USB port typically found in computers and USB hubs. It integrates the series resistors (R1) and the 15kΩ pull-down resistors (R2) for both USB data lines (D+ and D-) as well as the capacitors to ground for EMI suppression. Zener diodes provide ESD protection up to 15kV contact discharge per the IEC 61000-4-2 standard and protect the USB controller on both data lines. The PACUSB-D1/D2/D3 should be placed on the PCB between the USB controller and the USB connector, as shown on the Connection Diagram, Figure 5. Figure 5. Connection Diagram for PACUSB-D1/D2/D3 Devices To guarantee the best ESD and filtering performance, it is recommended to physically locate the PACUSBD1/D2/D3 close to the USB connector. Also, the trace lengths between the PACUSB-D1/D2/D3 and the USB controller should be kept as short as possible. Rev. 2 | Page 7 of 10 | www.onsemi.com PACUSB-D1/D2/D3 Mechanical Details PACUSB-D1/D2/D3 devices are packaged in SOT23-5 and SC70-5 packages. SOT23-5 Mechanical Specifications: Dimensions for PACUSB-D1/D2/D3 devices packaged in a 5-pin SOT23 package are presented below. For complete information on the SOT23-5 package, see the California Micro Devices SOT23 Package Information document. PACKAGE DIMENSIONS Package SOT23-5 (JEDEC name is MO-178) Pins 5 TOP VIEW e1 Millimeters e Inches Dimensions 5 Min Max Min 4 Max A -- 1.45 -- 0.057 A1 0.00 0.15 0.000 0.006 b 0.30 0.50 0.012 0.020 c 0.08 0.22 0.003 0.009 D 2.75 3.05 0.108 0.120 E 2.60 3.00 0.102 0.118 E1 1.45 1.75 0.057 0.069 E1 E 1 2 3 b SIDE VIEW e 0.95 BSC 0.0374 BSC e1 1.90 BSC 0.0748 BSC L L1 # per tape and reel 0.30 0.60 0.0236 0.60 REF D A A1 END VIEW 0.024 0.024 REF c 3000 pieces* L1 L Controlling dimension: millimeters * This is an approximate amount which may vary. Package Dimensions for SOT23-5. Rev. 2 | Page 8 of 10 | www.onsemi.com PACUSB-D1/D2/D3 Mechanical Details (continued) SC70-5 Mechanical Specifications: Dimensions for PACUSB-D1/D2/D3 devices packaged in a 5-pin SC70 package are presented below. For complete information on the SC70-5 package, see the California Micro Devices SC70 Package Information document. PACKAGE DIMENSIONS TOP VIEW Package SC70-5 (JEDEC name is MO-203 Issue A) Pins 5 e e 5 4 E HE Millimeters Dimensions 1 Min Max A 0.80 1.10 A1 0.00 0.10 A2 0.70 1.00 B 0.15 0.30 c 0.08 0.25 D 1.85 2.25 E 1.15 1.35 2 3 B SIDE VIEW D A2 A A1 0.65 BSC e END VIEW HE 2.00 2.40 L 0.26 0.46 # / bag 1000 pieces* # / tape and reel 3000 pieces* c L Package Dimensions for SC70-5. * This is an approximate amount which may vary. Rev. 2 | Page 9 of 10 | www.onsemi.com PACUSB-D1/D2/D3 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 Rev. 2 | Page 10 of 10 | www.onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative