1mm Pitch Connector for Vertical Connection FX5 Series Connecting Height: Low profile FX5_*P_SH ( 3.6 ) FX5_*S2A_DSA PCB ■Features Connecting Height: High profile 1. Header Side : 2 Types Available Two header types, low profile and high profile, are prepared according to the contact number variation and the connecting height variation, considering unit connections of HDD, FDD, CDROM and so on. FX5_*S2A_DSA FX5_*P_SH3 The connecting sequence is designed with 2 stages so that the end user side can maintain. 3. Mating Guide In the connecting process, the self-alignment is ±1mm high sufficient to the guide level, and the guide rib is provided to achieve easy mating. 4. SMT Coplanarity The coplanarity of SMT soldered area secures the high accuracy of 0.1mm. 5. Miniaturization The connector is miniaturized about 30% in the mounting area, compared with the conventional half pitch connector (1.27mm). ■Applications Note PC , other business equipments A206 ( 6.6 ) 2. Two-stages Sequential Structure PCB ■Product Specifications Current rating Rating Operating Temperature Range -55ç to +85ç (Note 1) Storage Temperature Range -10ç to +60ç (Note 2) 0.5A Voltage rating 100V AC Operating Humidity Range Item 40% to 80% Storage Humidity Range Specifications 40% to 70% Condition 1. Insulation Resistance 100M ohms min. 250V DC 2. Withstanding voltage No flashover or insulation breakdown. 300V AC/1 minute 3. Contact Resistance 50m ohms max. 100mA 4. Vibration No electrical discontinuity of 1µs or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Moisture Resistance Contact resistance: 60m ohms max. Insulation resistance: 100M ohms min. 96 hours at temperature of 40ç and humidity of 90% to 95% 6. Temperature Cycle Contact resistance: 60m ohms max. Insulation resistance: 100M ohms min. (-55ç: 30 minutes, 15 to 35ç: 2 to 3 minutes (-85ç: 30 minutes, 15 to 35ç: 2 to 3minutes) 5 cycles 7. Durability (Mating/un-mating) Contact resistance: 60m ohms max. 500 cycles 8. Resistance to Soldering heat No deformation of components affecting performance. Reflow: At the recommended temperature profile Manual soldering: 300ç for 3 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. ■Material Part Material Finish Remarks Beige Insulator Polyamide Header Contact Brass Contact area : Gold plated UL94V-0 ________ Receptacle Contact Phosphor bronze Lead area : Tin-lead plated ________ Note : The black dots on the insulater will not affect performance. ■Ordering Information ●Header FX5 – * P – SH 3 q q Series Name w e r t t Connector Height : FX5 w Number of Contacts : 20, 40, 52, 56, 68, 80 Blank : 6.5mm e Connector Type 3 : 9.5mm P: Header r Contact type SH : Right angle SMT type Note: The 56 contact header is for SH 3 type only. ●Receptacle FX5 q q Series Name – * S 2 A – DSA L w e : FX5 w Number of Contacts : 20, 40, 52, 56, 68, 80 e Connector Type S: Receptacle r Contact Sequence 2 : 2 Stages Sequence r t y u y Contact type DSA : Straight through hole type u Board prefixed pin Blank : Without board prefixed pin L : With board Prefixed pin t Serial No. : A A207 ■Header Low profile High profile A B±0.3 C±0.5 D±0.3 Polarity Mark * == (number of contacts)/2 a* A B±0.3 C±0.5 D±0.3 Polarity Mark 0 1_0.2 9.3±0.3 9.3±0.3 0 1_0.2 a2 1 a1 1.7±0.3 a* * * a1 6±0.3 b1 a2 1 b* b1 9.5±0.3 b* a1 6±0.3 a1 b2 ( 3.5 ) b2 * * b1 1.7±0.3 a1 b1 a2 E F±0.3 ( Ø1.3 ) t0.2±0.05∞w0.2±0.05 2_Ø2.3±0.15 b* a* 0.5 t0.2±0.05∞w0.2±0.05 2_Ø2.3±0.15 6.35±0.3 G±0.1 1.4±0.3 2.5±0.3 E F±0.3 3.2±0.2 2.5±0.3 6.35±0.3 3.2±0.2 2.5±0.3 b2 a1 b1 a2 1.4±0.3 2.5±0.3 ( 1.3 ) ( Ø1.3 ) b* a* b2 0.5 ( 1.3 ) 6.5±0.3 ( 0.5) b1 G±0.1 Unit: mm A208 Part Number CL No. FX5-20P-SH 575-0001-7 FX5-20P-SH3 575-0041-1 FX5-40P-SH 575-0005-8 FX5-40P-SH3 575-0045-2 FX5-52P-SH 575-0006-0 FX5-52P-SH3 575-0046-5 FX5-56P-SH3 575-1001-2 FX5-68P-SH 575-0008-6 FX5-68P-SH3 575-0048-0 FX5-80P-SH 575-0009-9 FX5-80P-SH3 575-0049-3 Number of Contacts A B C D E F G 20 9 24 22.9 19 9.5 20 13.6 40 19 34 32.9 29 19.5 30 23.6 52 25 40 38.9 35 25.5 36 29.6 56 27 42 40.9 37 27.5 38 31.6 68 33 48 46.9 43 33.5 44 37.6 80 39 54 52.9 49 39.5 50 43.6 A ±0.2 a2 a1 1 a* * * b1 a1 6±0.3 4.25±0.2 ■Receptacle * = (number of contacts)/2 b* b1 b2 5.9±0.2 B ±0.3 +0.1 –0.2 F 3.4±0.3 E F–F 3.3±0.3 E–E C F E 1.5±0.2 D ±0.3 1.5±0.2 0.6±0.3 1.5±0.2 3±0.3 t0.25±0.03xw0.4±0.05 Polarity Mark Unit: mm Part Number CL No. FX5-20S2A-DSA 575-0101-1 FX5-20S2A-DSAL 575-0121-9 FX5-40S2A-DSA 575-0105-2 FX5-40S2A-DSAL 575-0125-0 FX5-52S2A-DSA 575-0106-5 FX5-52S2A-DSAL 575-0126-2 FX5-56S2A-DSA 575-0107-8 FX5-56S2A-DSAL 575-0127-5 FX5-68S2A-DSA 575-0108-0 FX5-68S2A-DSAL 575-0128-8 FX5-80S2A-DSA 575-0109-3 FX5-80S2A-DSAL 575-0129-0 Number of Contacts 20 40 52 56 A 9 19 25 27 B 19 29 35 37 C 15.08 25.08 31.08 33.08 68 33 43 39.08 80 39 49 45.08 D Order of Contact Sequence(Contact No.) 1 2 __ a1,a2,a9,a10 15 __ b1,b2,b9,b10 b3 to b8 a1,a2,a19,a20 a3 to a18 25 __ b1,b2,b19,b20 b3 to b18 a1,a2,a25,a26 a3 to a24 31 __ b1,b2,b25,b26 b3 to b24 a1,a2,a27,a28 a3 to a26 33 __ b1,b2,b27,b28 b3 to b26 a1,a2,a33,a34 a3 to a32 39 __ b1,b2,b33,b34 b3 to b32 a1,a2,a39,a40 a3 to a38 45 b1,b2,b39,b40 b3 to b38 a3 to a8 A209 BPCB mounting pattern ●Header FX5-*-SH, FX5-*-SH3 4±0.1 A ±0.1 4±0.1 B ±0.05 C ±0.05 2.05±0.05 0.3±0.03 (Land pattern) 0.25±0.03 (Metal mask) 3.15±0.1 0.5±0.02 a* a2 2-Ø2.3 b* D±0.1 +0.1 0 2-Ø1.4±0.05 3.4±0.1 b2 b1 (Polarity mark position) 2.15±0.1 a1 2.1±0.1 2.55±0.1 (5.95) (Mating side) * = (number of contacts)/2 ●Receptacle FX5-*S2A-DSA 1.5±0.05 E ±0.1 1±0.05 a2 a1 a* a3 1.5±0.05 a4 b2 b4 Ø0.6 +0.1 0 b3 b* 1.5±0.05 b1 b* 1.5±0.05 (Polarity mark position) * = (number of contacts)/2 FX5-*S2A-DSAL F ±0.1 3±0.05 1.5±0.05 E ±0.1 1±0.05 a2 a* a3 a1 a4 2-Ø2.3 +0.1 0 1.5±0.05 (Polarity mark position) b1 b2 b4 Ø0.6 +0.1 0 b3 * = (number of contacts)/2 Unit: mm Number of Contacts A B C D E F 20 16 13.6 9.5 20 9 15 40 26 23.6 19.5 30 19 25 52 32 29.6 25.5 36 25 31 56 34 31.6 27.5 38 27 33 68 40 37.6 33.5 44 33 39 80 46 43.6 39.5 50 39 45 Note: If the connector is installed in the board beyond the above recommended size, it may cause the connector to board mounting failure or the soldering failure. It is desirable to implement the board process on the recommended PCB mounting pattern. A210 BRecommended Temperature Profile Less than 5 seconds 250 230ç 200 Temperature 200ç Applicable Conditions 160ç 150 150ç (ç) Reflow system :IR reflow Solder : Paste type 63 Sn/37 Pb Test board : Glass epoxy 85mm x 60mm x 1.6 mm (Flux content 9 wt%) 100 Metal mask thickness: 0.15 mm 50 60 seconds 60~90 seconds Preheating 0 START Recommended temperature profile. 30 seconds 25ç 60 20~30 seconds Soldering 120 The temperature may be slightly changed according to the solder paste type and amount. Time (Second) BCleaning Conditions 1. Organic Solvent Cleaning Solvent Cold Cleaning Heat Cleaning IPA (Isopropyl alcohol) HCFC (Hydrochlorophloro carbon) *Methylene chroride isn't suitable for this product solvent. 2. Liquid Cleaning When liquid detergents (such as terpene, alkali saponifier) are used, please select the cleaning detergent according to the influence table on metal or resin which is issued from each detergent manufacturer.In addition, please do not leave the connector outdoor, in which moisture remains. 3. Cautions for Cleaning As for organic solvent or liquid cleaning, if flux or detergent remains on the connector, it can cause electrical performance degradation. Therefore, please make sure that the connector is thoroughly cleaned so that neither flux nor detergent is found on the connector. A211 BConnector Precautions 1 1. Tolerance Clearance on Mating Side The effective connection clearance of the product is 1.6mm. Please use the product so as to specify within 1mm the clearance between the header and the receptacle in the connection process. 2. Header Connector Height The SMT connector height doesn't include the solder paste thickness. Thus, please consider that the stacking height will slightly increase after the mounting process. Mating Height: Low profile Mating Height: High profile FX5-*P-SH3 PCB ( 6.6) ( 3.6) FX5-πP-SH PCB 3. Screw Fastening Torque (SMT Type) When the screw is fastened, please use the M2 screw. The recommended fastening torque is 0.15(N.m) max. Nut (M2) Plain sheet (t = 0.3) Board (t = 1.6) Screw (M2) Spring sheet (t = 0.5) 4. Prefixed Process to Board (Through hole Type) If the prefixed process is required for board mounting, please use the prefixed pin type. (Applicable Thickness t = 1.6±0.1) Note: When the connector is mounted on the board, the dip post is guided into the board through-hole in order to prevent the dip post damage, and then insert the board in parallel to the connector so as to push in the prefixed pin. Prefixed pin PCB Dip post 5. Plug and Play When the connector is inserted or extracted in the active line state, please contact HRS company. 6. Others ● It is noted that the forced excessive insertion/extraction will result in damage. ● Avoid holding the board with the connector only, and fix the board by any other means except for the connector. ● The color phase of this product may be slightly different from that of the forming product according to the manufacturing lot, but the difference doesn't affect the performance. A212