ca_A1-A163.qxd:Layout 1 2/9/11 7:48 PM Page 1 ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 36 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Introduction Circular A The miniature circular connectors series KPT and KPSE from ITT Cannon conform to meet the performance specification of MIL-C-26482 with three point bayonet coupling and five-keyway polarization. They offer general purpose solder connectors and high performance crimp connectors. The broad product range provides the most complete family of connectors that conform to Mil-C-26482 and VG95328 performance specifications. The versatility of these connectors has been proven by their usage in general as well as in high performance environmental applications. In addition to the basic series presented in this section, connectors for special applications are available. They include corrosion resistant types, filter connectors for electromagnetic compatibility, and non-outgassing radiation resistant versions. All connectors conform to the above mentioned performance specifications and are fully intermateable and accept a wide range of interchangeable accessories. Thereby design modifications can be achieved more easily and at a lower cost with connectors of the KPT/KPSE series. KPT General purpose solder contact connectors KPT General purpose solder contact connectors • General purpose • Solder termination • Closed entry socket contacts Series KPT from ITT Cannon offers general purpose connectors used in military applications, but also widely used in industrial applications calling for a circular connector with fixed contacts for solder termination. The KPT series conforms to meet the performance specifications of MIL-C-26482 and is intermateable with all connectors according to the above specifications. VG95328H is also intermateable with the KPT and MIL-C-26482, see page A-62 Dimensions shown in inches (mm) Specifications and dimensions subject to change A-36 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 37 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Technical Data Material and Finishes KPT Shell Aluminum alloy, conductive olive drab chromate over cadmium finish per QQ-P-416 Contact Factor for other plating options KPSE Polychloroprene Polychloroprene Grommet and Seal Polychloroprene Polychloroprene Contacts Copper alloy, gold plated Copper alloy, gold plated MECHANICAL Shell Sizes Shell Sizes 00 - wall mounting receptacle 01 - cable connecting plug 02 - box mounting receptacle 06 - straight plut 07 - jam nut receptacle 08 - 90˚ angle plug B - thru-bulkhead receptacle (KPT only) Environmental Sealing KPT 8 thru 24 KPSE 10 thru 24 Polarization/Coupling: five keyway/three point bayonet Service Classes A - general duty B - general duty with strain relief E - grommet seal F - grommet seal with strain relief J - gland nut with strain relief for jacketed cable P - potted Acc. to VG95319 Part 2, Test No. 5.9.2. For styles A to E and J to W, Z1, Z2 and Z3 and gaskets style A and B only Test pressure 0,2 bar overpressure Test duration 48 h Test temperature 25 ± 3°C The connector shall be free of moisture See 26482 specification Operating temperature -55 / 125°C Electrical Data Number of contacts 2 thru 61 3 thru 61 Wire Size AWG 16 thru 24 12 thru 24 Contact termination Solder Crimp Contact rating Size AWG 20 16 12 Insulation resistance ⊕ 5000 MW Service rating Test voltage Sea level Exception: Service rating between the central contact and the housing of the coaxial contact 21336 m (70 000 ft) Operating voltage Service class 1 2 Operating voltage and connector usage Rated current A 7.5 13.0 23.0 Test current A 7.5 13.0 23.0 Millivolt drop mV less than 55 less than 50 less than 42 Service class 1 2 1 2 Vrms 1500 2300 375 550 VDC 2100 3200 535 770 VG 95328 140 VDC/100 VAC 165 VDC/115 VAC MIL-C-26482 850 VDC/600 VAC 1400 VDC/1000 VAC Connectors are equipment which must not be separated or mated when under load conditions. When the connectors will be operated with line voltage, please consult factory. Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com With scoop proof connectors operating voltages acc. to MIL-C-26482 and VG 96912 are permitted A-37 Circular Insulator A ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 38 Cannon KPT/KPSE MIL-C-26482 Series I Connectors KPT General purpose solder contact connectors How to order A MS KPT 3112 02 E E 22 22 - 55 55 P P W W • • Circular SERIES PREFIX SHELL STYLE CLASS SHELL SIZE CONTACT ARRANGEMENT CONTACT TYPE ALTERNATE INSERT POSITION MODIFICATION CODE SERIES PREFIX KPT -ITT Cannon prefix KPTR -ITT Cannon RoHS prefix (U.S. version) MS-MIL-DTL 26482 prefix SHELL STYLE ITT Cannon designation 00 -wall mounting receptacle 01 -cable connecting receptacle 02 -box mounting receptacle (class E only) 06 -straight plug 07 -jam nut receptacle 08 -90º angle plug B - thru bulkhead receptacle, see page A-49 CONTACT ARRANGEMENTS see page A-41 CONTACT TYPE P -Pin S -Socket ALTERNATE INSERT POSITION W, X, and Z (omit for normal), see page A-42 MODIFICATION CODE A34 - Electroless nickel hardware, RoHS compliant (European version) A71 - Electroless nickel hardware (U.S. version RoHS compliant after 11/1/07)) A206 - Black zinc cobalt hardware (U.S. version, RoHS compliant) MS DESIGNATION A232 - Black zinc cobalt hardware (European version, RoHS 3110 - Wall mounting receptacle compliant) 3111 - Cable connecting receptacle A233 - Green zinc cobalt hardware (European version) 3112 - Box mounting receptacle (Class E only) A408 - Extended Life Contact - Gold over Nickel 3114 - Jam nut receptacle DN - Shrink boot adapter for shell styles 00, 01, 06 and 07 3116 - Straight plug (Class E only) DZ - Endbell for shielding braids and shrink boots. CLASS (Class E only) A -general duty (not MS approved) 07 - Clear chromate over cadmium hardware (U.S. version) B -general duty with strain relief (not MS approved) with16 - Lanyard release (applicable to plug only) (U.S. version) out grommet and ferrule 23 - Ground springs (applicable to plug only) E -with a grommet seal, not for 02 and 3112 (MS specificaF42 - connectors without endbell and related components tion) F -grommet seal with strain relief (MS specification) P9 = PG9 for shell #10 M12 = M12x1,5 for shell #10 J -watertight gland seal with strain relief (MS P11 = PG11 for shell #12 M16 = M16x1,5 for shell #12 specification) for jacketed cable (U.S. version) P13 = PG13,5 for shell #14 M20 = M20x1,5 for shell #14 P -for potting (MS specification U.S. version) P16 = PG16 for shell #16 M25 = M25x1,5 for shell #16 PG - PG adapter (not available for shell #8) P21 = PG21 for shell #18 M25 = M25x1,5 for shell #18 ME - Metric adapter (not available for shell #8) P21 = PG21 for shell #20 M25 = M25x1,5 for shell #20 P21 = PG21 for shell #22 M32 = M32x1,5 for shell #22 SHELL SIZES P29 = PG29 for shell #24 M32 = M32x1,5 for shell #24 8, 10, 12, 14, 16, 18, 20, 22, and 24 Consult factory for other modifications. Omit first digit (0) of shell style indication when using a modification code. Dimensions shown in inches (mm) Specifications and dimensions subject to change A-38 www.ittcannon.com