MCC omponents 21201 Itasca Street Chatsworth !"# $ % !"# )HDWXUHV • • • 1N957 THRU 1N978 Zener Voltage 6.8V to 51V Silicon Planar Power Zener Diodes Standards zener voltage tolerance is ±20%, Add suffix “A” for ±10% tolerance and suffix “B” for ±5% tolerance, non standards and higher zener voltage upon request 0.5W Silicon Planar Zener Diodes DO-35 0HFKDQLFDO'DWD • • • Case: DO-35 glass case Polarity: Color band denotes cathode end Weight: Approx. 0.13 gram D 0D[LPXP5DWLQJV Symbol Zener Current Power Dissipation @ TA=25oC Junction Temperature Storage Temperature Range Ptot TJ TSTG Value See Table 1 Units 500 mW A Cathode Mark 175 o -65 to 175 o B C D C C (OHFWULFDO &KDUDFWHULVWLFV # °& 8QOHVV 2WKHUZLVH 6SHFLILHG Thermal resistance Forward Voltage @ IF=200mA Symbol R-$ Maximum 300 VF 1.5 Unit C/W o V NOTE: DIMENSIONS Valid provided that a distance of 8mm from case are kept at ambient temperature DIM A B C D INCHES MIN ------1.000 MAX .166 .079 .020 --- www.mccsemi.com MM MIN ------25.40 MAX 4.2 2.00 .52 --- NOTE MCC 1N957 thru 1N978 MCC PART NUMBER 1N957 1N958 1N959 1N960 1N961 1N962 1N963 1N964 1N965 1N966 1N967 1N968 1N969 1N970 1N971 1N972 1N973 1N974 1N975 1N976 1N977 1N978 Note: 1) 2) 3) ZENER VOLTAGE3) @TEST CURRENT VZ IZT V mA 6.8 18.5 7.5 16.5 8.2 15 9.1 14 10 12.5 11 11.5 12 10.5 13 9.5 15 8.5 16 7.8 18 7.0 20 6.2 22 5.6 24 5.2 27 4.6 30 4.2 33 3.8 36 3.4 39 3.2 43 3.0 47 2.7 51 2.5 MAXIMUM ZENER IMPEDANCE1) ZZT ZZK 4.5 5.5 5.5 5.5 5.5 5 11.5 13 16 17 21 25 29 33 41 49 58 70 80 93 105 125 700 700 700 700 700 700 700 700 700 700 750 750 750 750 750 1000 1000 1000 1000 1500 1500 1500 IZK mA 1.0 0.5 0.5 0.5 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 MAXIMUM REVERSE LEAKAGE CURRENT TEST-VOLTAGE IR2) A 150 75 50 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Suffix A V 4.9 5.4 5.9 6.6 7.2 8.0 8.6 9.4 10.8 11.5 13.0 14.4 15.8 17.3 19.4 21.6 23.8 25.9 28.1 31.0 33.8 36.7 Suffix B V 5.2 5.7 6.2 6.9 7.6 8.4 9.1 9.9 11.4 12.2 13.7 15.2 16.7 18.2 20.6 22.8 25.1 27.4 29.7 32.7 35.8 38.8 MAXIMUM ZENER CURRENT IZM2) mA 47 42 38 35 32 28 26 24 21 19 17 15 14 14 11 10 9.0 8.5 7.8 7.0 6.4 5.9 TYPICAL TEMP. COEFFICIENT : %/ 0.050 0.058 0.062 0.068 0.075 0.076 0.077 0.079 0.082 0.083 0.085 0.086 0.087 0.088 0.090 0.091 0.092 0.093 0.094 0.095 0.095 0.096 The Zener impedance is derived from the 1kHz AC voltage which results when an AC current having an RMS value equal to 10% of the Zener current (IZT) is superimposed on IZT Zener impedance is measured at two points to insure a sharp knee on the breakdown curve and to eliminate unstable units. Valid provided that leads are kept at ambient temperature at a distance of 8mm from case. Measured with device junction in thermal equilibrium. www.mccsemi.com