MCC FS2A THRU FS2M omponents 21201 Itasca Street Chatsworth !"# $ % !"# Features l Superfast Recovery Times For High Efficiency l For Surface Mount Application l Higher Temp Soldering: 250 C for 10 Seconds At Terminals l Available on Tape and Reel 2.0 Amp Fast Recovery Rectifier 50 to 1000 Volts o Maximum Ratings o o l Operating Temperature: -50 C to +150 C l Storage Temperature: -50 C to +150 C o MCC Catalog Number Device Marking FS2A FS2B FS2D FS2G FS2J FS2K FS2M FS2A FS2B FS2D FS2G FS2J FS2K FS2M DO-214AC (SMAJ) (High Profile) o Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 400V 600V 800V 1000V Maximum RMS Voltage Maximum DC Blocking Voltage 35V 70V 140V 280V 420V 560V 700V 50V 100V 200V 400V 600V 800V 1000V H Cathode Band J A Electrical Characteristics @ 25oC Unless Otherwise Specified Average Forward Current Peak Forward Surge Current IF(AV) 2.0A T J =90 oC IFSM 50A 8.3ms half sine Maximum Instantaneous Forward Voltage VF 1.30V Maximum DC Reverse Current At Rated DC Blocking Voltage IR 5.0uA Maximum Reverse Recovery Times FR2A-2G FR2J FR2K-2M Typical Junction Capacitance trr Cj IFM =2.0A o T A=25 C T J =25 oC IF =0.5A, IR=1.0A, Irr=0.25A 150ns 250ns 500ns 50pF Measured at 1.0MHz, VR =4.0V E C D B F G DIMENSIONS DIM A B C D E F G H J INCHES MIN .078 .067 .002 --.035 .065 .205 .160 .100 MM MIN 1.98 1.70 .05 --.89 1.65 5.21 4.06 2.57 MAX .116 .089 .008 .02 .055 .096 .224 .180 .112 MAX 2.95 2.25 .20 .51 1.40 2.45 5.69 4.57 2.84 SUGGESTED SOLDER PAD LAYOUT 0.090” 0.085” Pulse test: Pulse width 300 usec, duty cycle 2%. www.mccsemi.com 0.070” NOTE MCC FS2A thru FS2M Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 3.0 6 4 2.5 2 25°C Amps 2.0 1 .6 1.5 Amps .4 1.0 .2 .5 .1 Single Phase, Half Wave 60Hz Resistive or Inductive Load .06 0 .04 0 50 75 100 125 150 175 °C .02 .01 .4 .6 .8 1.0 Average Forward Rectified Current - Amperesversus Ambient Temperature - °C 1.4 12 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25°C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 Junction Capacitance - pFversus Reverse Voltage - Volts www.mccsemi.com 1000 MCC FS2A thru FS2M Figure 4 Maximum Non-Repetitive Forward Surge Current 90 75 60 45 Amps 30 15 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 5 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com