MITSUBISHI M37225ECSP

MITSUBISHI MICROCOMPUTERS
M37225M6-XXXSP, M37225M8-XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
1. DESCRIPTION
The M37225M6-XXXSP, M37225M8-XXXSP, and M37225ECSP are
single-chip microcomputers designed with CMOS silicon gate technology. They have a OSD, I2C-BUS interface, PWM output, and 12 V
withstand, so it is useful for a channel selection system for TV.
The features of the M37225ECSP are similar to those of the
M37225M6-XXXSP except that the chip has a built-in PROM which
can be written electrically. The difference between M37225M6-XXXSP
and M37225M8-XXXSP are the ROM size. Accordingly, the following descriptions will be for the M37225M6-XXXSP.
2. FEATURES
●Number of basic instructions .................................................... 71
●Memory size
ROM ..................... 24K bytes (M37225M6-XXXSP)
32K bytes (M37225M8-XXXSP)
48K bytes (M37225ECSP)
RAM ...................... 1024 bytes (M37225M6-XXXSP,
M37225M8-XXXSP)
2048 bytes (M37225ECSP)
(*ROM correction memory included)
●Minimum instruction execution time
......................................... 0.5 µs (at 8 MHz oscillation frequency)
●Power source voltage ................................................. 5 V ± 10 %
●Subroutine nesting ............................................. 128 levels (Max.)
●Interrupts ....................................................... 16 types, 16 vectors
●8-bit timers .................................................................................. 4
●Programmable I/O ports (Ports P0, P1, P2, P30–P32, P35) ..... 28
●Input ports (Ports P33, P34, P50, P51) ........................................ 4
●Output ports (Ports P52–P55) ..................................................... 4
●12 V withstand ports ................................................................... 6
●LED drive ports ........................................................................... 4
●Serial I/O ............................................................ 8-bit ✕ 1 channel
●Multi-master I2C-BUS interface .............................. 1 (2 systems)
●A-D converter (8-bit resolution) .................................... 8 channels
●PWM output circuit ........................................ 14-bit ✕ 2, 8-bit ✕ 6
●Power dissipation
In operating ...................................................................... 165 mW
(at VCC = 5.5V, 8 MHz oscillation frequency, and OSD on)
●ROM correction function ................................................ 3 vectors
●Immediate return mode from wait state
Rev. 1.1
●OSD function
Display characters ............................................... 24 characters ✕ 2 lines
(It is possible to display 3 lines or more by software)
Kinds of characters ......... 381 kinds
Character display area 16 ✕ 20 dots
Kinds of character sizes .............................. Block display: 3 kinds
SPRITE display: 1 kinds
Kinds of character colors. ................................. 8 colors (R, G, B)
Coloring unit ................... character, character background, raster
Display position
Horizontal: 64 levels
Vertical :255 levels
Attribute ........ Border (all-bordered, shadow-bordered), BUTTON
SPRITE display function
Wallpaper function
Window function
Corresponding to bi-scan mode
3. APPLICATION
TV
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
TABLE OF CONTENTS
1. DESCRIPTION .......................................................................... 1
2. FEAUTURES ............................................................................. 1
3. APPLICATION ............................................................................ 1
4. PIN CONFIGURATION .............................................................. 3
5. FUNCTIONAL BLOCK DIAGRAM ............................................. 4
6. PERFORMANCE OVERVIEW ................................................... 5
7. PIN DESCRIPTION ................................................................... 7
8. FUNCTIONAL DESCRIPTION ................................................. 11
8.1 CENTRAL PROCESSING UNIT (CPU) .................... 11
8.2 MEMORY .................................................................. 12
8.3 INTERRUPTS ........................................................... 19
8.4 TIMERS ..................................................................... 24
8.5 SERIAL I/O ................................................................ 27
8.6 MULTI-MASTER I2C-BUS INTERFACE .................... 31
8.7 PWM OUTPUT CIRCUIT .......................................... 44
8.8 A-D COMPARATOR .................................................. 49
8.9 ROM CORRECTION FUNCTION ............................. 53
8.10 OSD FUNCTIONS ................................................... 54
(1) Clock for OSD .................................................... 57
(2) Scan mode ......................................................... 58
(3) OSD input/output pin control .............................. 59
8.10.1 Block Display .................................................... 60
(1) Display position .................................................. 61
(2) Dot size .............................................................. 65
(3) Memory For OSD ............................................... 66
(4) Character Color .................................................. 69
(5) Character Background Color .............................. 69
(6) OUT1, OUT2 Signals ......................................... 69
(7) Attribute .............................................................. 72
(8) Multiple Display .................................................. 76
(9) Window Function ................................................ 77
8.10.2 SPRITE Display ................................................ 80
8.10.3 Raster Display ................................................... 83
8.11. SOFTWARE RUNAWAY DETECT FUNCTION ...... 85
8.12. RESET CIRCUIT .................................................... 86
8.13. CLOCK GENERATING CIRCUIT ........................... 87
8.14. DISPLAY OSCILLATION CIRCUIT ........................ 88
8.15. AUTO-CLEAR CIRCUIT ......................................... 88
8.16. ADDRESSING MODE ............................................ 88
8.17. MACHINE INSTRUCTIONS ................................... 88
9. PROGRAMMING NOTES ........................................................ 88
10. ABSOLUTE MAXIMUM RATINGS ......................................... 89
11. RECOMMENDED OPERATING CONDITIONS ..................... 89
12. ELECTRIC CHARACTERISTICS .......................................... 90
13. A-D COMPARISON CHARACTERISTICS ............................. 92
14. MULTI-MASTER I2C-BUS BUS LINE CHARACTERISTICS ........... 92
15. PROM PROGRAMMING METHOD ....................................... 93
16. DATA REQUIRED FOR MASK ORDERS .............................. 94
17. MASK CONFIRMATION FORM ............................................. 95
18. MARK SPECIFICATION FORM ........................................... 101
19. ONE TIME PROM VERSIONS M37225ECSP MARKING ... 102
20. APPENDIX ........................................................................... 103
21. PACKAGE OUTLINE ........................................................... 131
Rev. 1.0
2
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
4. PIN CONFIGURATION
1
42
R/P52
VSYNC/P51
P00/PWM0
P01/PWM1
P02/PWM2
P03/PWM3
P04/PWM4
P05/PWM5
P06/INT2/A-D4
P07/INT1
P23/TIM3
P24/TIM2
P25
P26
P27
DA1/P35
P32/A-D7
2
41
3
40
4
39
5
38
6
37
7
36
G/P53
B/P54
OUT1/P55
P20/SCLK
P21/SOUT(/SIN)
P22/SIN
8
9
10
11
12
13
14
M37225M6-XXXSP
M37225M8-XXXSP
M37225ECSP
HSYNC/P50
35
34
33
32
31
30
29
P10/OUT2/A-D8
P11/SCL1
P12/SCL2
P13/SDA1
P14/SDA2
P15/INT3/A-D1
P16/A-D2
P17/DA2/A-D3
P30/A-D5
15
28
16
27
17
26
CNVSS
XIN
XOUT
18
25
19
24
20
23
P31/A-D6
RESET
OSC1/P33
OSC2/P34
VSS
21
22
VC C
Outline 42P4B
Fig. 4.1 Pin Configuration (Top View)
Rev. 1.0
3
RAM
PCL (8)
PCH (8)
15 14 13 12 11 36 37 38
28 29 30 31 32 33 34 35
I/O port P1
10 9 8 7 6 5 4 3
I/O port P0
I/O port P2
P2 (8)
P1 (8)
17 26 27
P3 (6)
Stack
pointer
S (8)
ROM
18
I/O ports
P30–P32, P35
16
14-bit PWM
circuit 1
P0 (8)
A-D
converter
Index
register
Y (8)
counter
counter
Index
register
X (8)
Program
Program
Data bus
Processor
st a t u s
register
PS (8)
14-bit PWM
circuit 2
Accumulator
A (8)
Address bus
Clock
generating
circuit
8-bit
arithmetic
and logical
unit
INT2
INT1
21
TIM3
TIM2
Multi-master
I2C-BUS interface
Timer 4
T4 (8)
Timer 3
T3 (8)
Timer 2
T2 (8)
Timer 1
T1 (8)
Timer count source
selection circuit
SDA2
22
SDA1
25
SCL2
20
SCL1
19
SI/O(8)
Instruction
register (8)
Instruction
decoder
23
P 5 ( 6)
39 40 41 42
2
1
Output ports P52–P55
OSD output
Sync signal input
Input ports P50, P51
ROM correction
function
OSD circuit
OSC2
24
Clock output for OSD
OSC1
Clock input for OSD
8-bit
PWM circuit
Control signal
SIN
SCLK
SOUT
VSS CNVSS
PWM5
PWM4
PWM3
VC C
PWM2
Reset input
RESET
PWM1
Clock output
PWM0
XIN XOUT
OUT2
Clock input
OUT1
B
G
R
4
VSYNC
HSYNC
Input ports P33, P34
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
5. FUNCTIONAL BLOCK DIAGRAM
Fig. 5.1 Functional Block Diagram of M37225
Rev. 1.0
INT3
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
6. PERFORMANCE OVERVIEW
Table 6.1 Performance Overview
Parameter
Number of basic instructions
Instruction execution time
Clock frequency
Memory size
Input/Output
ports
Functions
ROM M37225M6-XXXSP
M37225M8-XXXSP
M37225ECSP
RAM M37225M6-XXXSP, M37225M8-XXXSP
M37225ECSP
OSD ROM
OSD RAM
I/O
P00–P05
P06, P07
I/O
P1
I/O
P2
I/O
P30, P31, P35
I/O
P32
P33, P34
P50, P51
P52–P55
Serial I/O
Multi-master I2C-BUS interface
A-D converter
PWM output circuit
Timers
ROM correction function
Subroutine nesting
Interrupt
Clock generating circuit
I/O
Input
Input
Output
71
0.5 µs (the minimum instruction execution time, at 8 MHz oscillation frequency)
8 MHz (maximum)
24K bytes
32K bytes
48K bytes
1024 bytes (ROM correction memory included)
2048 bytes (ROM correction memory included)
15K bytes
96 bytes
6-bit ✕ 1 (N-channel open-drain output structure, can be used as PWM
output pins)
2-bit ✕ 1 (N-channel open-drain output structure, can be used as INT input
pins, A-D input pin)
8-bit ✕ 1 (CMOS input/output structure, can be used as OSD output pin, INT
input pin, A-D input pins, DA output pin, multi-master I2C-BUS interface)
8-bit ✕ 1 (CMOS input/output structure, can be used as serial I/O pins,
timer external clock input pins)
3-bit ✕ 1 (CMOS output structure, or N-channel open-drain output structure, can be used as A-D input pins, DA output pin)
1-bit ✕ 1 (N-channel open-drain output structure, can be used as A-D input pin)
2-bit ✕ 1 (Can be used as OSD clock input/output pins)
2-bit ✕ 1 (N-channel open-drain output structure, can be used as horizonal
• vertical synchronous sibnal input pins)
4-bit ✕ 1 (CMOS output structure, can be used as OSD output pins)
8-bit ✕ 1
1 (2 systems)
8 channels (8-bit resolution)
14-bit ✕ 2, 8-bit ✕ 6
8-bit timer ✕ 4
3 vectors
128 levels (maximum)
<16 types>
INT external interrupt ✕ 3, Internal timer interrupt ✕ 6, Serial I/O interrupt ✕
1, OSD interrupt ✕ 1, Multi-master I2 C-BUS interface interrupt ✕ 1,
f(XIN)/4096 interrupt ✕ 1, SPRITE OSD interrupt ✕ 1, A-D conversion interrupt ✕ 1, VSYNC interrupt ✕ 1, BRK instruction interrupt ✕ 1, reset ✕ 1
2 built-in circuits (externally connected to a ceramic resonator or a quartzcrystal oscillator)
Rev. 1.0
5
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Table 6.2 Performance Overview (Continued)
OSD function
Parameter
Number of display characters
Dot structure
Kinds of characters
Kinds of character sizes
Character font coloring
Display position
Power source voltage
Power
OSD ON
dissipation
OSD OFF
In stop mode
Operating temperature range
Device structure
Package
Functions
24 characters ✕ 2 lines
16 ✕ 20 dots
381 kinds
3 kinds
1 screen : 8 kinds (per character unit)
Horizontal : 64 levels, Vertical : 255 levels
5V ± 10%
165 mW typ. ( at oscillation frequency f(XIN) = 8 MHz, fOSC = 8 MHz)
110 mW typ. ( at oscillation frequency f(XIN) = 8 MHz)
1.65 mW ( maximum )
–10 °C to 70 °C
CMOS silicon gate process
42-pin plastic molded SDIP
Rev. 1.0
6
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
7. PIN DESCRIPTION
Table 7.1 Pin Description
Pin
VCC,
VSS
CNVSS
Name
Input/
Output
Functions
Apply voltage of 5 V ± 10 % to (typical) VCC, and 0 V to VSS.
Power source
CNVSS
This is connected to VSS.
______
RESET
Reset input
Input
To enter the reset state, the reset input pin must be kept at a LOW for 2 µs or more (under
normal VCC conditions).
If more time is needed for the quartz-crystal oscillator to stabilize, this LOW condition should
be maintained for the required time.
XIN
Clock input
Input
XOUT
Clock output
This chip has an internal clock generating circuit. To control generating frequency, an
external ceramic resonator or a quartz-crystal oscillator is connected between pins XIN and
XOUT. If an external clock is used, the clock source should be connected to the XIN pin and
the XOUT pin should be left open.
P00/PWM0– I/O port P0
P05/PWM5,
P06/INT2/A-D4,
P07/INT1
PWM output
Output
I/O
Port P0 is an 8-bit I/O port with direction register allowing each I/O bit to be individually
programmed as input or output. At reset, this port is set to input mode. The output structure
is N-channel open-drain output. (See note 1)
Output
Pins P00–P05 are also used as PWM output pins PWM0–PWM5 respectively. The output
structure is N-channel open-drain output.
External interrupt
input
Input
Pins P06 and P07 are also used as INT external interrupt input pins INT2 and INT1
respectively.
Analog input
Input
P06 pin is also used as analog input pin A-D4.
P10/OUT2/A-D8, I/O port P1
P11/SCL1,
P12/SCL2, OSD output
P13/SDA1, Multi-master
P14/SDA2, I2C-BUS interface
P15/INT3/A-D1, Analog input
P16/A-D2, External interrupt
P17/DA2/A-D3 input
DA output
I/O
Output
I/O
Port P1 is an 8-bit I/O port and has basically the same functions as port P0. The
output structure is CMOS output. (See note 1)
Pins P10 is also used as OSD output pin OUT2. The output structure is CMOS output.
Pins P11–P14 are used as SCL1, SCL2, SDA1 and SDA2 respectively, when multi-master
I2C-BUS interface is used. The output structure is N-channel open-drain output.
Input
Pins P10, P15–P17 are also used as analog input pin A-D8, A-D1–A-D3 respectively.
Input
P15 pin is also used as INT external interrupt input pin INT3.
Output
Pins P17 is also used as 14-bit PWM output pin DA2. The output structure is CMOS output.
P20/SCLK,
I/O port P2
I/O
Port P2 is an 8-bit I/O port and has basically the same functions as port P0.
P22/SIN,
P23/TIM3,
P24/TIM2,
P25–P27
Serial I/O synchronous
clock input/output port
I/O
P20 pin is also used as serial I/O synchronous clock input/output pin SCLK. The output
structure is N-channel open-drain output.
Serial I/O data
input/output
I/O
P2 1 pin is also used as serial I/O data input/output pin S OUT (/S IN ). The output
structure is N-channel open-drain output.
The P21/SOUT(/SIN), output structure is CMOS output. (See note 1)
P30/A-D5,
P31/A-D6,
P32/A-D7,
DA1/P35
Serial I/O data input
Input
P22 pin is also used as serial I/O data input pin SIN.
External clock
input for timer
Input
Pins P2 3 and P2 4 are also used as timer external clock input pins TIM3 and TIM2
respectively.
I/O
Ports P30–P32 and P35 are a 3-bit I/O port and has basically the same functions as port 0
(see note 1). Either CMOS output or N-channel open-drain output structure can be selected
as ports P3 0 , P3 1 and P3 5 . The output structure of port P3 2 is N-channel
open-drain output structure.(See notes 1, 2)
I/O port P3
Analog input
DA output
OSC1/P33, Input port P3
OSC2/P34, Clock input for OSD
Clock output for OSD
Input
Output
Input
Input
Output
Pins P30–P32 are also used as analog input pins A-D5–A-D7 respectively.
P35 pin is also used as 14-bit PWM output pin DA1. The output structure is CMOS output. At
reset, output is undefined.
Pins P33 and P34 are a 2-bit input port.
P33 pin is also used as OSD clock input pin OSC1.
P34 pin is also used as OSD clock output pin OSC2. The output structure is CMOS output.
Rev. 1.0
7
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Table 7.2 Pin Description (continued)
Pin
Name
Input/
Output
Functions
HSYNC/P50, Input port P5
Input
Ports P50 and P51 are a 2-bit input port.
VSYNC/P51
Input
This is a horizontal synchronizing signal input for OSD.
Input
This is a vertical synchronizing signal input for OSD.
HSYNC input
VSYNC input
R/P52,
Output port P5
Output
Ports P52–P55 are a 4-bit output port. The output structure is CMOS output.
G/P53,
B/P54,
OSD output
Output
Pins P52–P55 are also used as OSD output pins R, G, B, OUT1 respectively. The output
structure is CMOS output. At reset, output is LOW.
OUT1/P55
Notes 1: Port Pi (i = 0 to 3) has the port Pi direction register which can be used to program each bit as an input (“0”) or an output (“1”). The pins programmed as “1”
in the direction register are output pins. When pins are programmed as “0,” they are input pins. When pins are programmed as output pins, the output data
are written into the port latch and then output. When data is read from the output pins, the output pin level is not read but the data of the port latch is read.
This allows a previously-output value to be read correctly even if the output LOW voltage has risen, for example, because a light emitting diode was directly
driven. The input pins are in the floating state, so the values of the pins can be read. When data is written into the input pin, it is written only into the port
latch, while the pin remains in the floating state.
2: To switch output structures, set by the following bits.
P30 : bit 6 of port P3 direction register
P31 : bit 7 of port P3 direction register
P35 : bit 5 of port P35 output mode control register
When “0,” CMOS output; when “1,” N-channel open-drain output.
Rev. 1.0
8
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Ports P00–P05
N-channel open-drain output
Direction register
Ports P00–P05
Data bus
Port latch
Note : Each port is also used as follows :
P0 0–P05 : PWM0–PWM5
Ports P1, P2, P30, P31
Direction register
Data bus
Port latch
CMOS output
Ports P1, P2, P30, P31, P35
Notes 1: Each port is also used as follows :
P10 : OUT2/AD8 P22 : SIN
P11 : SCL1
P23 : TIM3
P12 : SCL2
P24 : TIM2
P13 : SDA1
P30 : A-D5
P14 : SDA2
P31 : A-D6
P15 : INT3/A-D1 P35 : DA1
P16 : A-D2
P17 : DA2/A-D3
P20 : SCLK
P21 : SOUT/(SIN)
2: Either CMOS output or N-channel opendrain output structure can be selected as
ports P30, P31 and P35 (when selecting
N-channel open-drain, it is the same with
N-channel open-drain output below).
Ports P06, P07, P32
N-channel open-drain output
Direction register
Ports P06, P07, P32
Data bus
Port latch
Note : Each port is also used as follows :
P06 : INT2/A-D4
P07 : INT1
Fig. 7.1 I/O Pin Block Diagram (1)
Rev. 1.0
9
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
P52–P55
Data bus
Port latch
Internal circuit
CMOS output
Ports P52–P55
Note : Each pin is also used as follows :
P52 : R
P53 : G
P54 : B
P55 : OUT1
P50, P51
Data bus
Internal circuit
Schmidt input
Ports P50, P51
Note : Each pin is also used as follows :
P50 : HSYNC
P51 : VSYNC
P33, P34
Input
Data bus
Ports P33, P34
Note : Each pin is also used as follows :
P33 : OSC1
P34 : OSC2
Fig. 7.2 I/O Pin Block Diagram (2)
Rev. 1.0
10
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8. FUNCTIONAL DESCRIPTION
8.1 CENTRAL PROCESSING UNIT (CPU)
This microcomputer uses the standard 740 Family instruction set.
Refer to the table of 740 Family addressing modes and machine
instructions or the SERIES 740 <Software> User’s Manual for details on the instruction set.
Machine-resident 740 Family instructions are as follows:
The FST, SLW instruction cannot be used.
The MUL, DIV, WIT and STP instructions can be used.
8.1.1 CPU Mode Register
The CPU mode register contains the stack page selection bit and
internal system clock selection bit. The CPU mode register is allocated at address 00FB16.
CPU Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0 1 1 1
0 0
CPU mode register (CM) [Address 00FB16]
B
Name
Functions
After reset R W
0
R W
1
R W
3 to 5 Fix these bits to “1.”
1
R W
6, 7 Fix these bits to “0.”
0
R W
0, 1 Processor mode bits
(CM0, CM1)
2 Stack page selection
bit (CM2) (See note)
b1 b0
0
0
1
1
0: Single-chip mode
1:
0:
Not available
1:
0: 0 page
1: 1 page
Note: This bit is set to “1” after the reset release.
Fig. 8.1.1 CPU Mode Register
Rev. 1.0
11
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.2 MEMORY
8.2.1 Special Function Register (SFR) Area
The special function register (SFR) area in the zero page contains
control registers such as I/O ports and timers.
8.2.2 RAM
RAM is used for data storage and for stack area of subroutine calls
and interrupts.
8.2.3 ROM
ROM is used for storing user programs as well as the interrupt vector
area.
8.2.4 OSD RAM
RAM for display is used for specifying the character codes and colors to display.
8.2.5 OSD ROM
ROM for display is used for storing character data.
8.2.6 Interrupt Vector Area
The interrupt vector area contains reset and interrupt vectors.
8.2.7 Zero Page
The 256 bytes from addresses 000016 to 00FF16 are called the zero
page area. The internal RAM and the special function registers (SFR)
are allocated to this area.
The zero page addressing mode can be used to specify memory and
register addresses in the zero page area. Access to this area with
only 2 bytes is possible in the zero page addressing mode.
8.2.8 Special Page
The 256 bytes from addresses FF0016 to FFFF16 are called the special page area. The special page addressing mode can be used to
specify memory addresses in the special page area. Access to this
area with only 2 bytes is possible in the special page addressing
mode.
8.2.9 ROM Correction Vector
This is used as the program jump destination addresses for ROM
correction.
Rev. 1.0
12
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
¡M37255M6-XXXSP, M37255M8-XXXSP
000016
1000016
Zero page
SFR area
OSD ROM
(15K bytes)
00FF16
010016
01FF16
021716
021D16
(1024 bytes)
13BFF16
Not used
1540016
Not used
154FF16
2 page register (1)
1560016
Not used
156FF16
Not used
024016
Not used
2 page register (2)
024F16
Not used
1140016
00BF16
00C016
1580016
Not used
158FF16
02C016
Not used
ROM correction function
Vector 1: address 02C016
02E016
Vector 2: address 02E016
030016
15A0016
15AFF16
Not used
Vector 3: address 030016
15C0016
15CFF16
Not used
15E0016
04FF16
OSD RAM
(96 byres)
(See note)
Not used
15EFF16
080016
Not used
1600016
087716
160FF16
Not used
1620016
162FF16
Not used
1640016
164FF16
Not used
1660016
166FF16
Not used
1680016
168FF16
Not used
16A0016
16AFF16
Not used
16C0016
16CFF16
Not used
16E0016
Not used
16EFF16
Not used
1700016
170FF16
Not used
1720016
172FF16
Not used
1740016
174FF16
Not used
1760016
176FF16
Not used
1780016
178FF16
Not used
17A0016
17AFF16
M37225M8XXXSP
ROM
(32K bytes)
M37225M6XXXSP
ROM
(24K bytes)
800016
A00016
Not used
FF0016
FFDE16
FFFF16
Interrupt vector area
Special page
Note: Refer to Table 8.10.3 OSD RAM.
1FFFF16
Fig. 8.2.1 Memory Map (M37225M6-XXXSP, M37225M8-XXXSP)
Rev. 1.0
13
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
¡M37255ECSP
000016
1000016
Not used
1140016
00BF16
00C016
Zero page
SFR area
OSD ROM
(15K bytes)
00FF16
010016
01FF16
RAM
(2048 bytes)
021716
021D16
13BFF16
Not used
1540016
Not used
154FF16
2 page register (1)
1560016
Not used
156FF16
Not used
024016
Not used
2 page register (2)
024F16
1580016
Not used
158FF16
02C016
Not used
ROM correction function
Vector 1: address 02C016
02E016
Vector 2: address 02E016
030016
15A0016
15AFF16
Not used
Vector 3: address 030016
15C0016
15CFF16
Not used
OSD RAM
(96 bytes)
(See note)
15E0016
07FF16
080016
15EFF16
Not used
087716
1600016
Not used
090016
160FF16
Not used
09FF16
1620016
162FF16
Not used
1640016
164FF16
Not used
1660016
166FF16
Not used
1680016
168FF16
Not used
16A0016
16AFF16
Not used
16C0016
16CFF16
Not used
Not used
16E0016
16EFF16
Not used
1700016
170FF16
Not used
1720016
172FF16
Not used
1740016
174FF16
Not used
1760016
176FF16
Not used
1780016
178FF16
Not used
17A0016
17AFF16
400016
Not used
ROM
(48K byte)
Note: Refer to Table 8.10.13 OSD RAM.
FF0016
FFDE16
FFFF16
Interrupt vector area
Special page
1FFFF16
Fig. 8.2.2 Memory Map (M37225ECSP)
Rev. 1.0
14
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ SFR area (addresses C016 to DF16)
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
C016
C116
C216
C316
C416
C516
C616
C716
C816
C916
CA16
CB16
CC16
CD16
CE16
CF16
D016
D116
D216
D316
D416
D516
D616
D716
D816
D916
DA16
DB16
DC16
DD16
DE16
DF16
Register
Bit allocation
State immediately after reset
b0 b7
b7
b0
Port P0 (P0)
Port P0 direction register (D0)
Port P1 (P1)
Port P1 direction register (D1)
Port P2 (P2)
Port P2 direction register (D2)
Port P3 (P3)
Port P3 direction register (D3)
Port P35 output mode control register (P3S)
Port P5 (P5)
OSD port control register (PF)
P35 P34IN P33IN P32
P31S P30S P35D
0
0
0
P35S
P55 P54
OUT OUT
OUT2 P55 P54
SEL SEL SEL
Test register
Interrupt input polarity register (IP)
P53
OUT
P53
SEL
1
0
0
P31 P30
P32D P31D P30D
POL3 POL2 POL1
P52 P51
OUT IN
P52
SEL 0
1
0
P50
IN
0
0
0
0
0
0
0
0
?
0
0
0
0
0
?
0
0
0
0
OCG1OCG0
DA1-H register (DA1-H)
DA1-L register (DA1-L)
PWM0 register (PWM0)
PWM1 register (PWM1)
PWM2 register (PWM2)
PWM3 register (PWM3)
PWM4 register (PWM4)
PWM output control register 1 (PW)
PW7 PW6 PW5 PW4 PW3 PW2 PW1 PW0
PWM output control register 2 (PN)
0
0
I2C
D7
D6
data shift register (S0)
I2C address register (S0D)
I2C status register (S1)
I2 C
control register (S1D)
I2C clock control register (S2)
Serial I/O mode register (SM)
P N5 P N4 P N3 P N2
D5
D4
D3
D2
0
0
D1
D0
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
MST TRX BB
PIN
AL AAS AD0 LRB
BSEL1 BSEL0 10BIT ALS ESO BC2 BC1 BC0
SAD
ACK
ST
ACK BIT MFA
ODE CCR4 CCR3 CCR2 CCR1 CCR0
SM6 SM5
0
SM3 SM2 SM1 SM0
Serial I/O register (SIO)
AD conversion register (AD)
AD control register (ADCON)
0
0
ADVREF ADSTR ADIN2 ADIN1 ADIN0
?
0016
?
0016
?
0016
?
? ?
?
0 ?
? ?
0016
0 1
0016
?
? ?
?
?
?
?
?
0016
0016
?
0016
1 0
0016
0016
0016
?
?
0816
0
0
0
?
?
?
?
?
?
1
?
?
?
?
?
0
0
?
Fig. 8.2.3 Memory Map of Special Function Register (SFR) (1)
Rev. 1.0
15
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ SFR area (addresses E016 to FF16)
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
Bit allocation
Register
State immediately after reset
b0 b7
b7
E016
E116
E216
E316
E416
E516
E616
E716
E816
E916
EA16
EB16
EC16
ED16
EE16
EF16
F016
F116
F216
F316
F416
F516
F616
F716
F816
F916
FA16
FB16
FC16
FD16
FE16
FF16
Block H register (BHP)
b0
BHP5 BHP4 BHP3 BHP2 BHP1 BHP0
Block 1V register (B1VP)
B1VP7 B1VP6 B1VP5 B1VP4 B1VP3 B1VP2 B1VP1 B1VP0
Block 2V register (B2VP)
B2VP7 B2VP6 B2VP5 B2VP4 B2VP3 B2VP2 B2VP1 B2VP0
SPRITE control register (SC)
SC7 SC6 SC5 SC4 SC3 SC2 SC1 SC0
SPRITE H register (SHP)
SPRITE V register (SVP)
Color register 1 (CO1)
SHP7 SHP6 SHP5 SHP4 SHP3 SHP2 SHP1 SHP0
SVP7 SVP6 SVP5 SVP4 SVP3 SVP2 SVP1 SVP0
CO16 CO15 CO14 CO13 CO12 CO11 CO10
Color register 2 (CO2)
CO26 CO25 CO24 CO23 CO22 CO21 CO20
Color register 3 (CO3)
CO36 CO35 CO34 CO33 CO32 CO31 CO30
Color register 4 (CO4)
CO46 CO45 CO44 CO43 CO42 CO41 CO40
OSD control register (OC)
OC7 OC6 OC5 OC4 OC3 OC2 OC1 OC0
OSD I/O polarity control register (OPC)
Color register 5 (CO5)
OPC7 OPC6 OPC5 OPC4 OPC3 OPC2 OPC1 OPC0
CO56 CO55 CO54 CO53 CO52 CO51 CO50
Color register 6 (CO6)
CO66 CO65 CO64 CO63 CO62 CO61 CO60
Color register 7 (CO7)
CO76 CO75 CO74 CO73 CO72 CO71 CO70
Color register 8 (CO8)
CO86 CO85 CO84 CO83 CO82 CO81 CO80
0
0
0
0
?
?
?
?
?
?
?
?
0
0
0
0
?
?
?
?
?
?
?
?
0
0
0
0
0
0
Timer 1 (T1)
Timer 2 (T2)
Timer 3 (T3)
Timer 4 (T4)
Timer mode register 1 (TM1)
TM15 TM14 TM13 TM12 TM11 TM10
Timer mode register 2 (TM2)
TM25 TM24 TM23 TM22 TM21 TM20
PWM5 register (PWM5)
0016
0016
Test register
Test register
B1C4 B1C3 B1C2 B1C1 B1C0
Block 1 control register (B1C)
Block 2 control register (B2C)
B2C4 B2C3 B2C2 B2C1 B2C0
0
0
1
1
1
CM2
0
0
CPU mode register (CM)
Interrupt request register 1 (IREQ1)
IT3R IICR VSCR OSDR TM4R TM3R TM2R TM1R
Interrupt request register 2 (IREQ2)
Interrupt control register 1 (ICON1)
IT3E IICE VSCE OSDE TM4E TM3E TM2E TM1E
Interrupt control register 2 (ICON2)
0
MCSKR0 SPR S1R IT2R IT1R
A DR
A DE
0
MSE SPE S1E IT2E IT1E
0016
?
?
0016
0016
?
? ?
? ?
? ?
? ?
0016
0016
? ?
? ?
? ?
? ?
FF16
0716
FF16
0716
0016
0016
?
?
?
C?K0 ?
C?K0 ?
3C16
0016
0016
0016
0016
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
Fig. 8.2.4 Memory Map of Special Function Register (SFR) (2)
Rev. 1.0
16
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ 2 page register area (addresses 21016 to 21F16, 24016 to 24F16)
Bit allocation
:
Name
State immediately after reset
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
21016
21116
21216
21316
21416
21516
21616
21716
21816
21916
21A16
21B16
21C16
21D16
21E16
21F16
24016
24116
24216
24316
24416
24516
24616
24716
24816
24916
24A16
24B16
24C16
24D16
24E16
24F16
Register
Bit allocation
b7
State immediately after reset
b0 b7
b0
ROM correction address 1 (high-order)
ROM correction address 1 (low-order)
ROM correction address 2 (high-order)
ROM correction address 2 (low-order)
ROM correction enable register (RCR)
0
0
0
0
0
RCR2 RCR1RCR0
ROM correction address 3 (high-order)
ROM correction address 3 (low-order)
Left border control register (LBR)
Right border control register (RBR)
LBR6 LBR5 LBR4 LBR3 LBR2 LBR1 LBR0
RBR6 RBR5 RBR4 RBR3 RBR2 RBR1 RBR0
Top border control register (TBR) TBR7 TBR6 TBR5 TBR4 TBR3 TBR2 TBR1 TBR0
Bottom border control register (BBR) BBR7 BBR6 BBR5 BBR4 BBR3 BBR2 BBR1 BBR0
0016
Test register
DA2-H register (DA2H)
DA2-L register (DA2L)
0
0
?
?
?
?
?
?
?
?
0016
0016
0016
0016
0016
0016
0016
?
?
0016
0016
?
?
?
?
?
0016
?
?
?
?
?
?
?
? ?
?
?
?
Fig. 8.2.5 Memory Map of 2 Page Register Area
Rev. 1.0
17
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Register
Bit allocation
State immediately after reset
b0 b7
b7
Processor status register (PS)
Program counter (PCH)
Program counter (PCL)
N
V
T
B
D
I
Z
C
b0
? ? ? ? ? 1 ? ?
Contents of address FFFF16
Contents of address FFFE16
Fig. 8.2.6 Internal State of Processor Status Register and Program Counter at Reset
Rev. 1.0
18
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.3 INTERRUPTS
Interrupts can be caused by 16 different sources consisting of 3 external, 14 internal, 1 software, and reset. Interrupts are vectored interrupts with priorities as shown in Table 8.3.1. Reset is also included
in the table because its operation is similar to an interrupt.
When an interrupt is accepted,
① The contents of the program counter and processor status register are automatically stored into the stack.
➁ The interrupt disable flag I is set to “1” and the corresponding
interrupt request bit is set to “0.”
➂ The jump destination address stored in the vector address enters
the program counter.
Other interrupts are disabled when the interrupt disable flag is set to
“1.”
All interrupts except the BRK instruction interrupt have an interrupt
request bit and an interrupt enable bit. The interrupt request bits are
in interrupt request registers 1 and 2 and the interrupt enable bits are
in interrupt control registers 1 and 2. Figures 8.3.2 to 8.3.6 show the
interrupt-related registers.
Interrupts other than the BRK instruction interrupt and reset are accepted when the interrupt enable bit is “1,” interrupt request bit is “1,”
and the interrupt disable flag is “0.” The interrupt request bit can be
set to “0” by a program, but not set to “1.” The interrupt enable bit can
be set to “0” and “1” by a program.
Reset is treated as a non-maskable interrupt with the highest priority.
Figure 8.3.1 shows interrupt control.
8.3.1 Interrupt Causes
(1) VSYNC, OSD, SPRITE OSD Interrupts
The VSYNC interrupt is an interrupt request synchronized with
the vertical sync signal.
The OSD interrupt occurs after character block display to the
CRT is completed.
The SPRITE OSD interrupt occurs at the completion of SPRITE
display.
(2) INT1 to INT3 External Interrupts
The INT1 to INT3 interrupts are external interrupt inputs, the system detects that the level of a pin changes from LOW to HIGH or
from HIGH to LOW, and generates an interrupt request. The input active edge can be selected by bits 3 to 5 of the interrupt
input polarity register (address 00CD16) : when this bit is “0,” a
change from LOW to HIGH is detected; when it is “1,” a change
from HIGH to LOW is detected. Note that both bits are cleared to
“0” at reset.
(3) Timers 1 to 4 Interrupts
An interrupt is generated by an overflow of timers 1 to 4.
Table 8.3.1 Interrupt Vector Addresses and Priority
Priority
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Interrupt Source
Reset
OSD interrupt
INT2 external interrupt
INT1 external interrupt
SPRITE OSD interrupt
Timer 4 interrupt
f(XIN)/4096 interrupt
VSYNC interrupt
Timer 3 interrupt
Timer 2 interrupt
Timer 1 interrupt
Serial I/O interrupt
Multi-master I2C-BUS interface interrupt
INT3 external interrupt
A-D conversion interrupt
BRK instruction interrupt
Vector Addresses
FFFF16, FFFE16
FFFD16, FFFC16
FFFB16, FFFA16
FFF916, FFF816
FFF716, FFF616
FFF516, FFF416
FFF316, FFF216
FFF116, FFF016
FFEF16, FFEE16
FFED16, FFEC16
FFEB16, FFEA16
FFE916, FFE816
FFE716, FFE616
FFE516, FFE416
FFE316, FFE216
FFDF16, FFDE16
Remarks
Non-maskable
Active edge selectable
Active edge selectable
Active edge selectable
Non-maskable
Rev. 1.0
19
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(4) Serial I/O Interrupt
This is an interrupt request from the clock synchronous serial I/O
function.
(5) f(XIN)/4096 Interrupt
The f (XIN)/4096 interrupt occurs regularly with a f(XIN)/4096 period. Set bit 0 of the PWM mode register 1 to “0.”
(6) Multi-master I2C-BUS Interface Interrupt
Interrupt request bit
Interrupt enable bit
Interrupt disable flag I
This is an interrupt request related to the multi-master I2C-BUS
interface.
BRK instruction
Reset
Interrupt
request
(7) A-D Conversion Interrupt
The A-D conversion interrupt occurs at the completion of A-D
conversion.
(8) BRK Instruction Interrupt
Fig. 8.3.1 Interrupt Control
This software interrupt has the least significant priority. It does
not have a corresponding interrupt enable bit, and it is not affected by the interrupt disable flag I (non-maskable).
Rev. 1.0
20
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Interrupt Request Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Interrupt request register 1 (IREQ1) [Address 00FC16]
B
Name
0 Timer 1 interrupt
request bit (TM1R)
Functions
After reset
0
0 : No interrupt request issued
1 : Interrupt request issued
Timer 2 interrupt
0
0 : No interrupt request issued
request bit (TM2R) 1 : Interrupt request issued
0
Timer 3 interrupt
0 : No interrupt request issued
request bit (TM3R) 1 : Interrupt request issued
0
Timer 4 interrupt
0 : No interrupt request issued
request bit (TM4R) 1 : Interrupt request issued
OSD interrupt request 0 : No interrupt request issued
0
1 : Interrupt request issued
bit (OSDR)
VSYNC interrupt
0
0 : No interrupt request issued
request bit (VSCR) 1 : Interrupt request issued
0
Multi-master I2C-BUS interface 0 : No interrupt request issued
interrupt request bit (IICR)
1 : Interrupt request issued
INT3 external interrupt 0 : No interrupt request issued
0
request bit (IT3R)
1 : Interrupt request issued
R W
R ✽
1
R ✽
2
3
4
5
6
7
R ✽
R ✽
R ✽
R ✽
R ✽
R ✽
✽: “0” can be set by software, but “1” cannot be set.
Fig. 8.3.2 Interrupt Request Register 1
Interrupt Request Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt request register 2 (IREQ2) [Address 00FD16]
B
Name
Functions
After reset
0 INT1 external interrupt 0 : No interrupt request issued
0
1 : Interrupt request issued
request bit (IT1R)
0
1 INT2 external interrupt 0 : No interrupt request issued
1 : Interrupt request issued
request bit (IT2R)
2 Serial I/O interrupt
0
0 : No interrupt request issued
request bit (S1R)
1 : Interrupt request issued
0
3 SPRITE OSD interrupt 0 : No interrupt request issued
request bit (SPR)
1 : Interrupt request issued
0
4 f(XIN)/4096 interrupt 0 : No interrupt request issued
request bit (MSR)
1 : Interrupt request issued
5 Nothing is assigned. This bit is a write disable bit.
0
When this bit is read out, the value is “0.”
0
6 A-D conversion interrupt 0 : No interrupt request issued
request bit (ADR)
1 : Interrupt request issued
7
Fix this bit to “0.”
0
R W
R ✽
R ✽
R ✽
R ✽
R ✽
R —
R ✽
R W
✽: “0” can be set by software, but “1” cannot be set.
Fig. 8.3.3 Interrupt Request Register 2
Rev. 1.0
21
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Interrupt Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Interrupt control register 1 (ICON1) [Address 00FE16]
B
Name
Functions
After reset R W
0 Timer 1 interrupt
enable bit (TM1E)
1 Timer 2 interrupt
enable bit (TM2E)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
2 Timer 3 interrupt
enable bit (TM3E)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
3 Timer 4 interrupt
enable bit (TM4E)
4 OSD interrupt enable bit
(OSDE)
5 VSYNC interrupt enable
bit (VSCE)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
6 Multi-master I2C-BUS interface 0 : Interrupt disabled
interrupt enable bit (IICE)
1 : Interrupt enabled
0
R W
7 INT3 external interrupt
enable bit (IT3E)
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
Fig. 8.3.4 Interrupt Control Register 1
Interrupt Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt control register 2 (ICON2) [Address 00FF16]
B
Name
0 INT1 external interrupt
enable bit (IT1E)
1 INT2 external interrupt
enable bit (IT2E)
2 Serial I/O interrupt
enable bit (S1E)
S
PRITE OSD interrupt
3
enable bit (SPE)
4 f(XIN)/4096 interrupt
enable bit (MSE)
5 Fix this bit to “0.”
Functions
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
6 A-D conversion interrupt 0 : Interrupt disabled
enable bit (ADE)
1 : Interrupt enabled
N
o
t
h
i
n
g
i
s
a
s
s
i
g
n
e
d
.
T
h
i
s
b
it is a write disable
7
bit. When this bit is read out, the value is “0.”
After reset R W
0
R W
0
R W
0
R W
0
R W
0
R W
0
R W
0
R W
0
R —
Fig. 8.3.5 Interrupt Control Register 2
Rev. 1.0
22
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Interrupt Input Polarity Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0
0
Interrupt input polarity register (IP) [Address 00CD16]
b
Name
0, 1 OSD clock
selection bits
(OCG0, OCG1)
Function
After reset R W
Function
b1 b0
0 0 The clock for OSD is supplied by connecting RC
or LC across the pins OSC1 and OSC2. However,
it is not corresponding to the bi-scan mode.
0
1 Since the main clock is used as the
clock for OSD, the oscillation
frequency is limited. Because of
this, the character size in width
(horizonal) direction is also limited.
In this case, pins OSC1 and OSC2
are also used as input ports P33
and P34 respectively.
1
0
1
1
0
R W
0
R W
OSD
oscillation
frequency =
f(XIN)
The clock for OSD is supplied by connecting LC
across the pins OSC1 and OSC2. In the bi-scan
mode, be sure to set this.
The clock for OSD is supplied by connecting the
following across the pins OSC1 and OSC2.
However, it is not corresponding to the bi-scan
mode.
• a ceramic resonator only for OSD and a
feedback resistor
• a quartz-crystal oscillator only for OSD and a
feedback resistor
2
Fix this bit to “0.”
3
INT1 polarity
switch bit (POL1)
0 : Positive polarity
1 : Negative polarity
0
R W
4
INT2 polarity
switch bit (POL2)
0 : Positive polarity
1 : Negative polarity
0
R W
5
INT3 polarity
switch bit (POL3)
0 : Positive polarity
1 : Negative polarity
0
R W
0
R W
6, 7 Fix these bits to “0.”
Fig. 8.3.6 Interrupt Input Polarity Register
Rev. 1.0
23
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.4 TIMERS
This microcomputer has 4 timers: timers 1 to 4. All timers are 8-bit
timers with the 8-bit timer latch. The timer block diagram is shown in
Figure 8.4.3.
All of the timers count down and their divide ratio is 1/(n+1), where n
is the value of timer latch. By writing a count value to the corresponding timer latch (addresses 00F016 to 00F316 : timers 1 to 4), the value
is also set to a timer, simultaneously.
The count value is decremented by 1. The timer interrupt request bit
is set to “1” by a timer overflow at the next count pulse, after the
count value reaches “0016.”
Timer 1 can select one of the following count sources:
• f(XIN)/16
• f(XIN)/4096 or f(XCIN)/4096
The count source of timer 1 is selected by setting bit 0 of timer mode
register 1 (address 00F416).
Timer 1 interrupt request occurs at timer 1 overflow.
At reset, timers 3 and 4 are connected by hardware and “FF16” is
automatically set in timer 3; “07 16” in timer 4. The f(XIN)/16 is selected as the timer 3 count source. The internal reset is released by
timer 4 overflow in this state and the internal clock is connected.
At execution of the STP instruction, timers 3 and 4 are connected by
hardware and “FF16” is automatically set in timer 3; “0716” in timer 4.
However, the f(XIN)/16 is not selected as the timer 3 count source.
So set both bit 0 of timer mode register 2 (address 00F516) and bit 6
at address 00C716 to “0” before execution of the STP instruction
(f(XIN)/16 is selected as the timer 3 count source). The internal STP
state is released by timer 4 overflow in this state and the internal
clock is connected.
As a result of the above procedure, the program can start under a
stable clock.
However, when setting “1” to bit 5 of timer mode register 1 (address
00F416), timers 3 and 4 are not set the above value, the STP state is
set by executing the STP instruction. This allows to program the time
to return from the STP state.
8.4.2 Timer 2
The timer-related registers is shown in Figures 8.4.1 and 8.4.2.
8.4.1 Timer 1
Timer 2 can select one of the following count sources:
• f(XIN)/16
• Timer 1 overflow signal
• External clock from the TIM2 pin
The count source of timer 2 is selected by setting bits 4 and 1 of
timer mode register 1 (address 00F416). When timer 1 overflow signal is a count source for the timer 2, the timer 1 functions as an 8-bit
prescaler.
Timer 2 interrupt request occurs at timer 2 overflow.
8.4.3 Timer 3
Timer 3 can select one of the following count sources:
• f(XIN)/16
• External clock from the HSYNC pin
• External clock from the TIM3 pin
The count source of timer 3 is selected by setting bits 5 and 0 of
timer mode register 2 (address 00F516).
Timer 3 interrupt request occurs at timer 3 overflow.
8.4.4 Timer 4
Timer 4 can select one of the following count sources:
• f(XIN)/16
• f(XIN)/2
• Timer 3 overflow signal
The count source of timer 3 is selected by setting bits 1 and 4 of
timer mode register 2 (address 00F516). When timer 3 overflow signal is a count source for the timer 4, the timer 3 functions as an 8-bit
prescaler.
Timer 4 interrupt request occurs at timer 4 overflow.
Rev. 1.0
24
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Timer Mode Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Timer mode register 1 (TM1) [Address 00F416]
B
Name
Functions
0
Timer 1 count source
selection bit 1 (TM10)
0: f(XIN)/16
1: f(XIN)/4096
0
R W
1
Timer 2 count source
selection bit 1 (TM11)
0: Interrupt clock source
1: External clock from TIM2 pin
0
R W
2 Timer 1 count
stop bit (TM12)
0: Count start
1: Count stop
0
R W
3 Timer 2 count stop bit
(TM13)
0: Count start
1: Count stop
0
R W
4 Timer 2 internal count source 0: f(XIN)/16
1: Timer 1 overflow
selection bit 2 (TM14)
0
R W
5 <At execution of STP
instruction>
Timers 3 and 4 auto
set disable bit (TM15)
0
R W
0
R —
0: Auto set enabled
1: Auto set disabled
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
After reset R W
Fig. 8.4.1 Timer Mode Register 1
Timer Mode Register 2
b7 b6 b5 b4 b3 b2 b1 b0
Timer mode register 2 (TM2) [Address 00F516]
B
Name
0 Timer 3 count source
selection bit (TM20)
1
Functions
0 : f(XIN)/16
1 : External clock source
After reset R W
0
R W
0 : Timer 3 overflow signal
1 : f(XIN)/16
0
R W
2 Timer 3 count stop bit
(TM22)
0: Count start
1: Count stop
0
R W
3 Timer 4 count stop bit
(TM23)
0: Count start
1: Count stop
0
R W
4 Timer 4 count source
selection bit (TM24)
0: Internal clock source
1: f(XIN)/2
0
R W
0
R W
0
R —
5
Timer 4 internal
interrupt count source
selection bit (TM21)
Timer 3 external count
0: TIM3 pin input
source selection bit (TM25) 1: HSYNC pin input
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
Fig. 8.4.2 Timer Mode Register 2
Rev. 1.0
25
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Data bus
8
Timer 1 latch (8)
1/4096
8
XIN
1 /2
1/8
Timer 1
interrupt request
Timer 1 (8)
TM10
TM12
8
TM14
8
Timer 2 latch (8)
8
TIM2
Timer 2
interrupt request
Timer 2 (8)
TM11
TM13
8
HSYNC
8
Reset
FF16
TM25
TIM3
STP instruction
TM15
Timer 3 latch (8)
8
Timer 3
interrupt request
Timer 3 (8)
TM20
TM22
8
8
Selection gate : Connected to
black side at
reset
0716
TM21
Timer 4 latch (8)
TM1 : Timer mode register 1
TM2 : Timer mode register 2
8
Timer 4
interrupt request
Timer 4 (8)
TM24
TM23
8
Notes 1: HIGH pulse width of timer external clock inputs TIM2 and TIM3 needs 4 machine cycles or more.
2: When the external clock source is selected, timers 1, 2, and 3 are counted at a rising edge of input signal.
3: In the stop mode or the wait mode, external clock inputs TIM2 and TIM3 cannot be used.
Fig. 8.4.3 Timer Block Diagram
Rev. 1.0
26
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.5 SERIAL I/O
This microcomputer has a built-in serial I/O which can either transmit
or receive 8-bit data serially in the clock synchronous mode.
The serial I/O block diagram is shown in Figure 8.5.1. The synchronous clock I/O pin (SCLK), and data output pin (SOUT) also function
as port P4, data input pin (SIN) also functions as port P2.
Bit 3 of the serial I/O mode register (address 00DC16) selects whether
the synchronous clock is supplied internally or externally (from the
SCLK pin). When an internal clock is selected, bits 1 and 0 select
whether f(XIN) or f(XCIN) is divided by 4, 16, 32, or 64. To use SIN pin
for serial I/O, set the corresponding bit of the port P2 direction register (address 00C516) to “0.”
The operation of the serial I/O is described below. The operation of
the serial I/O differs depending on the clock source; external clock or
internal clock.
Data bus
XIN
1/2
Frequency divider
1/2
1/4
Synchronous
circuit
1/16 1/32
1/64
SM1
SM0
SM2
S
SM : Serial I/O mode register
P20 latch
SCLK
Serial I/O
interrupt request
Serial I/O counter (8)
SM3
P21 latch
Selection gate : Connected to
black side at
reset
@
SM5 : LSB
SOUT
MSB
SM3
(See note)
SIN
Serial I/O shift register (8)
SM6
8 (Address 00DD16)
Note : When the data is set in the serial I/O register (address 00DD16), the register functions as the serial I/O shift register.
Fig. 8.5.1 Serial I/O Block Diagram
Rev. 1.0
27
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Internal clock : The serial I/O counter is set to “7” during the write
cycle into the serial I/O register (address 00DD16), and the transfer
clock goes HIGH forcibly. At each falling edge of the transfer clock
after the write cycle, serial data is output from the SOUT pin. Transfer
direction can be selected by bit 5 of the serial I/O mode register. At
each rising edge of the transfer clock, data is input from the SIN pin
and data in the serial I/O register is shifted 1 bit.
After the transfer clock has counted 8 times, the serial I/O counter
becomes “0” and the transfer clock stops at HIGH. At this time the
interrupt request bit is set to “1.”
External clock : The an external clock is selected as the clock source,
the interrupt request is set to “1” after the transfer clock has been
counted 8 counts. However, transfer operation does not stop, so the
clock should be controlled externally. Use the external clock of 1 MHz
or less with a duty cycle of 50%.
The serial I/O timing is shown in Figure 8.5.2. When using an external clock for transfer, the external clock must be held at HIGH for
initializing the serial I/O counter. When switching between an internal clock and an external clock, do not switch during transfer. Also,
be sure to initialize the serial I/O counter after switching.
Notes 1: On programming, note that the serial I/O counter is set by writing to
the serial I/O register with the bit managing instructions, such as SEB
and CLB.
2: When an external clock is used as the synchronous clock, write transmit data to the serial I/O register when the transfer clock input level is
HIGH.
Synchronous clock
Transfer clock
Serial I/O register
write signal
(Note)
Serial I/O output
SOUT
D0
D1
D2
D3
D4
D5
D6
D7
Serial I/O input
SIN
Interrupt request bit is set to “1”
Note : When an internal clock is selected, the SOUT pin is at high-impedance after transfer is completed.
Fig. 8.5.2 Serial I/O Timing (for LSB first)
Rev. 1.0
28
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Serial I/O Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0
Serial I/O mode register (SM) [Address 00DC16]
B
Name
0, 1 Internal synchronous
clock selection bits
(SM0, SM1)
Functions
b1 b0
0 0: f(XIN)/4
0 1: f(XIN)/16
1 0: f(XIN)/32
1 1: f(XIN)/64
After reset R W
0
R W
2
Synchronous clock
selection bit (SM2)
0: External clock
1: Internal clock
0
R W
3
Serial I/O port
selection bit (SM3)
0: P20, P21
1: SCLK, SOUT
0
R W
0
R W
4 Fix this bit to “0.”
5
Transfer direction
selection bit (SM5)
0: LSB first
1: MSB first
0
R W
6
Serial input pin
selection bit (SM6)
0: Input signal from SIN pin.
1: Input signal from SOUT pin.
0
R W
7
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
0
R —
Fig. 8.5.3 Serial I/O Mode Register
Rev. 1.0
29
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.5.1 Serial I/O Common Transmission/Reception mode
By writing “1” to bit 6 of the serial I/O mode register, signals SIN and
SOUT are switched internally to be able to transmit or receive the
serial data.
Figure 8.5.4 shows signals on serial I/O common transmission/reception mode.
Note: When receiving the serial data after writing “FF16” to the serial I/O register.
SCLK
Clock
SOUT
“1”
Serial I/O shift register (8)
SIN
“0”
SM6
SM : Serial I/O mode register
Fig. 8.5.4 Signals on Serial I/O Common Transmission/Reception Mode
Rev. 1.0
30
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6 MULTI-MASTER I2C-BUS INTERFACE
Table 8.6.1 Multi-master I2C-BUS Interface Functions
The multi-master I2C-BUS interface is a serial communications circuit, conforming to the Philips I2C-BUS data transfer format. This
interface, offering both arbitration lost detection and a synchronous
functions, is useful for the multi-master serial communications.
Figure 8.6.1 shows a block diagram of the multi-master I2C-BUS interface and Table 8.6.1 shows multi-master I2C-BUS interface functions.
This multi-master I2C-BUS interface consists of the I2C address register, the I2C data shift register, the I2C clock control register, the I2C
control register, the I2C status register and other control circuits.
Item
Format
Communication mode
SCL clock frequency
Function
In conformity with Philips I2C-BUS
standard:
10-bit addressing format
7-bit addressing format
High-speed clock mode
Standard clock mode
In conformity with Philips I2C-BUS
standard:
Master transmission
Master reception
Slave transmission
Slave reception
16.1 kHz to 400 kHz (at φ = 4 MHz)
φ : System clock = f(XIN)/2
Note : We are not responsible for any third party’s infringement of patent rights
or other rights attributable to the use of the control function (bits 6 and 7
of the I2C control register at address 00DA16) for connections between
the I2C-BUS interface and ports (SCL1, SCL2, SDA1, SDA2).
b7
I2C address register (S0D) b0
Interrupt
generating
circuit
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
Interrupt
request signal
(IICIRQ)
Address comparator
Serial
data
(SDA)
Noise
elimination
circuit
Data
control
circuit
b7
b0
2
I C data shift register
b7
S0
b0
AL AAS AD0 LRB
MST TRX BB PIN
2
AL
circuit
I C status
register (S1)
Internal data bus
BB
circuit
Serial
clock
(SCL)
Noise
elimination
circuit
Clock
control
circuit
b7
ACK
b0
ACK FAST CCR4 CCR3 CCR2 CCR1 CCR0
MODE
BIT
I2C clock control register (S2)
Clock division
b7
BSEL1 BSEL0 10BIT
SAD
b0
ALS
ESO BC2 BC1 BC0
I2C control register (S1D)
System clock (φ)
Bit counter
Fig. 8.6.1 Block Diagram of Multi-master I2C-BUS Interface
Rev. 1.0
31
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.1 I2C Data Shift Register
The I2C data shift register (S0 : address 00D716) is an 8-bit shift
register to store receive data and write transmit data.
When transmit data is written into this register, it is transferred to the
outside from bit 7 in synchronization with the SCL clock, and each
time one-bit data is output, the data of this register are shifted one bit
to the left. When data is received, it is input to this register from bit 0
in synchronization with the SCL clock, and each time one-bit data is
input, the data of this register are shifted one bit to the left.
The I2C data shift register is in a write enable status only when the
ESO bit of the I2C control register (address 00DA16) is “1.” The bit
counter is reset by a write instruction to the I2C data shift register.
When both the ESO bit and the MST bit of the I2C status register
(address 00D916) are “1,” the SCL is output by a write instruction to
the I2C data shift register. Reading data from the I2C data shift register is always enabled regardless of the ESO bit value.
Note: To write data into the I2C data shift register after setting the MST bit to
“0” (slave mode), keep an interval of 8 machine cycles or more.
I2C Data Shift Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C data shift register (S0) [Address 00D716 ]
B
0
to
7
Name
Functions
D0 to D7 This is an 8-bit shift register to store
receive data and write transmit data.
After reset
R W
Indeterminate
R W
Note: To write data into the I2C data shift register after setting the MST bit to
“0” (slave mode), keep an interval of 8 machine cycles or more.
Fig. 8.6.2 Data Shift Register
Rev. 1.0
32
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.2 I2C Address Register
The I2C address register (address 00D816) consists of a 7-bit slave
address and a read/write bit. In the addressing mode, the slave address written in this register is compared with the address data to be
received immediately after the START condition are detected.
(1) Bit 0: read/write bit (RBW)
Not used when comparing addresses, in the 7-bit addressing mode.
In the 10-bit addressing mode, the first address data to be received
is compared with the contents (SAD6 to SAD0 + RBW) of the I2C
address register.
The RBW bit is cleared to “0” automatically when the stop condition
is detected.
(2) Bits 1 to 7: slave address (SAD0–SAD6)
These bits store slave addresses. Regardless of the 7-bit addressing mode and the 10-bit addressing mode, the address data transmitted from the master is compared with the contents of these bits.
I2C Address Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C address register (S0D) [Address 00D816]
B
Name
Functions
After reset R W
0
Read/write bit
(RBW)
<Only in 10-bit addressing (in slave) mode>
The last significant bit of address data is
compared.
0: Wait the first byte of slave address after
START condition
(read state)
1: Wait the first byte of slave address after
RESTART condition
(write state)
0
R —
1
to
7
Slave address
(SAD0 to SAD6)
<In both modes>
The address data is compared.
0
R W
Fig. 8.6.3 I2C Address Register
Rev. 1.0
33
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.3 I2C Clock Control Register
(4) Bit 7: ACK clock bit (ACK)
The I2C clock control register (address 00DB16) is used to set ACK
control, SCL mode and SCL frequency.
This bit specifies a mode of acknowledgment which is an acknowledgment response of data transmission. When this bit is set to “0,”
the no ACK clock mode is set. In this case, no ACK clock occurs
after data transmission. When the bit is set to “1,” the ACK clock
mode is set and the master generates an ACK clock upon completion of each 1-byte data transmission.The device for transmitting
address data and control data releases the SDA at the occurrence of
an ACK clock (make SDA HIGH) and receives the ACK bit generated
by the data receiving device.
(1) Bits 0 to 4: SCL frequency control bits (CCR0–CCR4)
These bits control the SCL frequency.
(2) Bit 5: SCL mode specification bit (FAST MODE)
This bit specifies the SCL mode. When this bit is set to “0,” the standard clock mode is set. When the bit is set to “1,” the high-speed
clock mode is set.
(3) Bit 6: ACK bit (ACK BIT)
This bit sets the SDA status when an ACK clock✽ is generated. When
this bit is set to “0,” the ACK return mode is set and SDA goes to
LOW at the occurrence of an ACK clock. When the bit is set to “1,”
the ACK non-return mode is set. The SDA is held in the HIGH status
at the occurrence of an ACK clock.
However, when the slave address matches the address data in the
reception of address data at ACK BIT = “0,” the SDA is automatically
made LOW (ACK is returned). If there is a mismatch between the
slave address and the address data, the SDA is automatically made
HIGH (ACK is not returned).
Note: Do not write data into the I2C clock control register during transmission.
If data is written during transmission, the I2C clock generator is reset, so
that data cannot be transmitted normally.
✽ACK clock: Clock for acknowledgement
I2C Clock Control Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C clock control register (S2) [Address 00DB16]
B
0
to
4
Name
Functions
After reset R W
SCL frequency control bits Setup value of Standard clock High speed
(CCR0 to CCR4)
CCR4–CCR0
mode
clock mode
0 0 to 0 2
Setup disabled
04
Setup disabled
250
05
100
83.3
400 (See note)
333
166
...
500/CCR value 1000/CCR value
1D
17.2
34.5
1E
16.6
33.3
32.3
1F
R W
Setup disabled Setup disabled
03
06
0
16.1
(at φ = 4 MHz, unit : kHz)
5
SCL mode
specification bit
(FAST MODE)
0: Standard clock mode
1: High-speed clock mode
0
R W
6
ACK bit
(ACK BIT)
0: ACK is returned.
1: ACK is not returned.
0
R W
7
ACK clock bit
(ACK)
0: No ACK clock
1: ACK clock
0
R W
Note: At 400 kHz in the high-speed clock mode, the duty is as below .
“0” period : “1” period = 3 : 2
In the other cases, the duty is as below.
“0” period : “1” period = 1 : 1
Fig. 8.6.4 I2C Address Register
Rev. 1.0
34
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.4 I2C Control Register
(3) Bit 4: data format selection bit (ALS)
The I2C control register (address 00DA16) controls the data communication format.
This bit decides whether or not to recognize slave addresses. When
this bit is set to “0,” the addressing format is selected, so that address data is recognized. When a match is found between a slave
address and address data as a result of comparison or when a general call (refer to “8.6.5 I2C Status Register,” bit 1) is received, transmission processing can be performed. When this bit is set to “1,” the
free data format is selected, so that slave addresses are not recognized.
(1) Bits 0 to 2: bit counter (BC0–BC2)
These bits decide the number of bits for the next 1-byte data to be
transmitted. An interrupt request signal occurs immediately after the
number of bits specified with these bits are transmitted.
When a START condition is received, these bits become “0002” and
the address data is always transmitted and received in 8 bits.
(2) Bit 3: I2C interface use enable bit (ESO)
This bit enables usage of the multimaster I2C BUS interface. When
this bit is set to “0,” the use disable status is provided, so the SDA
and the SCL become high-impedance. When the bit is set to “1,” use
of the interface is enabled.
When ESO = “0,” the following is performed.
• PIN = “1,” BB = “0” and AL = “0” are set (they are bits of the I2C
status register at address 00D916 ).
• Writing data to the I2C data shift register (address 00D716) is disabled.
(4) Bit 5: addressing format selection bit (10BIT SAD)
This bit selects a slave address specification format. When this bit is
set to “0,” the 7-bit addressing format is selected. In this case, only
the high-order 7 bits (slave address) of the I2C address register (address 00D816) are compared with address data. When this bit is set
to “1,” the 10-bit addressing format is selected, all the bits of the I2C
address register are compared with address data.
(5) Bits 6 and 7: connection control bits between
I 2 C-BUS interface and ports
(BSEL0, BSEL1)
These bits controls the connection between SCL and ports or SDA
and ports (refer to Figure 8.6.5).
“0”
“1” BSEL0
P11/SCL1
SCL
Multi-master
I2C-BUS
interface
SDA
“0”
“1” BSEL1
P12/SCL2
“0”
“1” BSEL0
P13/SDA1
“0”
“1” BSEL1
P14/SDA2
Fig. 8.6.5 Connection Port Control by BSEL0 and BSEL1
Rev. 1.0
35
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
I2C Control Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C control register (S1D) [Address 00DA16]
B
Name
Functions
After reset R W
0
to
2
Bit counter
(Number of transmit/recieve
bits)
(BC0 to BC2)
b2
0
0
0
0
1
1
1
1
b0
0: 8
1: 7
0: 6
1: 5
0: 4
1: 3
0: 2
1: 1
0
R W
3
I2C-BUS interface use
enable bit (ESO)
0: Disabled
1: Enabled
0
R W
4
Data format selection
bit(ALS)
0: Addressing format
1: Free data format
0
R W
5
Addressing format selection
bit (10BIT SAD)
0: 7-bit addressing format
1: 10-bit addressing format
0
R W
b7 b6 Connection port (See note)
0 0: None
0 1: SCL1, SDA1
1 0: SCL2, SDA2
1 1: SCL1, SDA1, SCL2, SDA2
0
R W
6, 7 Connection control bits
between I2C-BUS interface
and ports
(BSEL0, BSEL1)
b1
0
0
1
1
0
0
1
1
Note: When using ports P11-P14 as I2C-BUS interface, the output structure changes
automatically from CMOS output to N-channel open-drain output.
Fig. 8.6.6 I2C Control Register
Rev. 1.0
36
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.5 I2C Status Register
(5) Bit 4: I2C-BUS interface interrupt request bit (PIN)
The I2C status register (address 00D916) controls the I2C-BUS interface status. The low-order 4 bits are read-only bits and the highorder 4 bits can be read out and written to.
This bit generates an interrupt request signal. Each time 1-byte data
is transmitted, the state of the PIN bit changes from “1” to “0.” At the
same time, an interrupt request signal is sent to the CPU. The PIN bit
is set to “0” in synchronization with a falling edge of the last clock
(including the ACK clock) of an internal clock and an interrupt request signal occurs in synchronization with a falling edge of the PIN
bit. When the PIN bit is “0,” the SCL is kept in the “0” state and clock
generation is disabled. Figure 8.6.8 shows an interrupt request signal generating timing chart.
The PIN bit is set to “1” in any one of the following conditions.
• Executing a write instruction to the I2C data shift register (address
00D716).
• When the ESO bit is “0”
• At reset
The conditions in which the PIN bit is set to “0” are shown below:
• Immediately after completion of 1-byte data transmission (including when arbitration lost is detected)
• Immediately after completion of 1-byte data reception
• In the slave reception mode, with ALS = “0” and immediately after
completion of slave address or general call address reception
• In the slave reception mode, with ALS = “1” and immediately after
completion of address data reception
(1) Bit 0: last receive bit (LRB)
This bit stores the last bit value of received data and can also be
used for ACK receive confirmation. If ACK is returned when an ACK
clock occurs, the LRB bit is set to “0.” If ACK is not returned, this bit is
set to “1.” Except in the ACK mode, the last bit value of received data
is input. The state of this bit is changed from “1” to “0” by executing a
write instruction to the I2C data shift register (address 00D716).
(2) Bit 1: general call detecting flag (AD0)
This bit is set to “1” when a general call✽ whose address data is all
“0” is received in the slave mode. By a general call of the master
device, every slave device receives control data after the general
call. The AD0 bit is set to “0” by detecting the STOP condition or
START condition.
✽General call: The master transmits the general call address “0016”
to all slaves.
(3) Bit 2: slave address comparison flag (AAS)
This flag indicates a comparison result of address data.
■ In the slave receive mode, when the 7-bit addressing format is
selected, this bit is set to “1” in one of the following conditions.
• The address data immediately after occurrence of a START condition matches the slave address stored in the high-order 7 bits
of the I2C address register (address 00D816).
• A general call is received.
■ In the slave reception mode, when the 10-bit addressing format is
selected, this bit is set to “1” with the following condition.
• When the address data is compared with the I2C address register (8 bits consists of slave address and RBW), the first bytes
match.
■ The state of this bit is changed from “1” to “0” by executing a write
instruction to the I2C data shift register (address 00D716).
(4) Bit 3: arbitration lost✽ detecting flag (AL)
n the master transmission mode, when a device other than the microcomputer sets the SDA to “L,”, arbitration is judged to have been
lost, so that this bit is set to “1.” At the same time, the TRX bit is set to
“0,” so that immediately after transmission of the byte whose arbitration was lost is completed, the MST bit is set to “0.” When arbitration
is lost during slave address transmission, the TRX bit is set to “0” and
the reception mode is set. Consequently, it becomes possible to receive and recognize its own slave address transmitted by another
master device.
✽Arbitration lost: The status in which communication as a master is
disabled.
(6) Bit 5: bus busy flag (BB)
This bit indicates the status of use of the bus system. When this bit is
set to “0,” this bus system is not busy and a START condition can be
generated. When this bit is set to “1,” this bus system is busy and the
occurrence of a START condition is disabled by the START condition
duplication prevention function (See note).
This flag can be written by software only in the master transmission
mode. In the other modes, this bit is set to “1” by detecting a START
condition and set to “0” by detecting a STOP condition. When the
ESO bit of the I2C control register (address 00DA16) is “0” and at
reset, the BB flag is kept in the “0” state.
(7) Bit 6: communication mode specification bit
(transfer direction specification bit: TRX)
This bit decides the direction of transfer for data communication. When
this bit is “0,” the reception mode is selected and the data of a transmitting device is received. When the bit is “1,” the transmission mode
is selected and address data and control data are output into the
SDA in synchronization with the clock generated on the SCL.
When the ALS bit of the I2C control register (address 00DA16) is “0”
in the slave reception mode is selected, the TRX bit is set to “1”
___
(transmit) if the least significant bit (R/W bit) of the address data trans___
mitted by the master is “1.” When the ALS bit is “0” and the R/W bit is
“0,” the TRX bit is cleared to “0” (receive).
The TRX bit is cleared to “0” in one of the following conditions.
• When arbitration lost is detected.
• When a STOP condition is detected.
• When occurence of a START condition is disabled by the START
condition duplication prevention function (Note).
• With MST = “0” and when a START condition is detected.
• With MST = “0” and when ACK non-return is detected.
• At reset
Rev. 1.0
37
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(8) Bit 7: Communication mode specification bit
(master/slave specification bit: MST)
This bit is used for master/slave specification for data communication. When this bit is “0,” the slave is specified, so that a START
condition and a STOP condition generated by the master are received,
and data communication is performed in synchronization with the
clock generated by the master. When this bit is “1,” the master is
specified and a START condition and a STOP condition are generated, and also the clocks required for data communication are generated on the SCL.
The MST bit is cleared to “0” in one of the following conditions.
• Immediately after completion of 1-byte data transmission when
arbitration lost is detected
• When a STOP condition is detected.
• When occurence of a START condition is disabled by the START
condition duplication preventing function (Note).
• At reset
Note: The START condition duplication prevention function disables the START
condition generation, reset of bit counter reset, and SCL output, when
the following condition is satisfied:
a START condition is set by another master device.
I2C Status Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C status register (S1) [Address 00D916]
B
Functions
Name
R —
0 : No general call detected
1 : General call detected
(See note)
0
R —
Slave address comparison
flag (AAS) (See note)
0 : Address mismatch
1 : Address match
0
R —
Arbitration lost detecting flag
(AL) (See note)
0 : Not detected
1 : Detected
0
R —
1
R W
0
R W
0
R W
0 : Last bit = “0 ”
1 : Last bit = “1 ”
1
General call detecting flag
(AD0) (See note)
2
3
After reset R W
Indeterminate
Last receive bit (LRB)
(See note)
0
4
I2C-BUS interface interrupt
request bit (PIN)
5
Bus busy flag (BB)
6, 7 Communication mode
specification bits
(TRX, MST)
(See note)
(See note)
(See note)
0 : Interrupt request issued
1 : No interrupt request issued
0 : Bus free
1 : Bus busy
b7
0
0
1
1
b6
0 : Slave recieve mode
1 : Slave transmit mode
0 : Master recieve mode
1 : Master transmit mode
Note : These bits and flags can be read out, but cannnot be written.
Fig. 8.6.7 I2C Status Register
SCL
PIN
IICIRQ
Fig. 8.6.8 Interrupt Request Signal Generation Timing
Rev. 1.0
38
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.6 START Condition Generation Method
When the ESO bit of the I2C control register (address 00DA16) is “1,”
execute a write instruction to the I2C status register (address 00D916)
to set the MST, TRX and BB bits to “1.” A START condition will then
be generated. After that, the bit counter becomes “0002” and an SCL
for 1 byte is output. The START condition generation timing and BB
bit set timing are different in the standard clock mode and the highspeed clock mode. Refer to Figure 8.6.9 for the START condition
generation timing diagram, and Table 8.6.2 for the START condition/
STOP condition generation timing table.
I2C status register
write signal
SCL
Setup
time
SDA
Hold time
Set time for
BB flag
BB flag
Setup
time
Fig. 8.6.9 START Condition Generation Timing Diagram
8.6.7 STOP Condition Generation Method
When the ESO bit of the I2C control register (address 00DA16) is “1,”
execute a write instruction to the I2C status register (address 00D916)
for setting the MST bit and the TRX bit to “1” and the BB bit to “0”. A
STOP condition will then be generated. The STOP condition generation timing and the BB flag reset timing are different in the standard
clock mode and the high-speed clock mode. Refer to Figure 8.6.10
for the STOP condition generation timing diagram, and Table 8.6.2
for the START condition/STOP condition generation timing table.
I2C status register
write signal
SCL
SDA
BB flag
Setup
time
Hold time
Reset time for
BB flag
Fig. 8.6.10 STOP Condition Generation Timing Diagram
Table 8.6.2 START Condition/STOP Condition Generation Timing Table
Item
Standard Clock Mode
Setup time
5.0 µs (20 cycles)
(START condition)
Setup time
4.25 µs (17 cycles)
(STOP condition)
5.0 µs (20 cycles)
Hold time
Set/reset time
3.0 µs (12 cycles)
for BB flag
High-speed Clock Mode
2.5 µs (10 cycles)
1.75 µs (7 cycles)
2.5 µs (10 cycles)
1.5 µs (6 cycles)
Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the
number of φ cycles.
Rev. 1.0
39
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.8 START/STOP Condition Detect Conditions
8.6.9 Address Data Communication
The START/STOP condition detect conditions are shown in
Figure 8.6.11 and Table 8.6.3. Only when the 3 conditions of Table
8.6.3 are satisfied, a START/STOP condition can be detected.
There are two address data communication formats, namely, 7-bit
addressing format and 10-bit addressing format. The respective address communication formats is described below.
Note: When a STOP condition is detected in the slave mode
(MST = 0), an interrupt request signal “IICIRQ” is generated to the
CPU.
(1) 7-bit addressing format
SCL release time
SCL
SDA
(START condition)
Setup
time
Hold time
Setup
time
Hold time
To meet the 7-bit addressing format, set the 10BIT SAD bit of the I2C
control register (address 00DA16) to “0.” The first 7-bit address data
transmitted from the master is compared with the high-order 7-bit
slave address stored in the I2C address register (address 00D816).
At the time of this comparison, address comparison of the RBW bit of
the I2C address register (address 00D816) is not made. For the data
transmission format when the 7-bit addressing format is selected,
refer to Figure 8.6.12, (1) and (2).
(2) 10-bit addressing format
SDA
(STOP condition)
Fig. 8.6.11 START Condition/STOP Condition Detect Timing Diagram
Table 8.6.3 START Condition/STOP Condition Detect Conditions
Standard Clock Mode
6.5 µs (26 cycles) < SCL
release time
3.25 µs (13 cycles) < Setup time
3.25 µs (13 cycles) < Hold time
High-speed Clock Mode
1.0 µs (4 cycles) < SCL
release time
0.5 µs (2 cycles) < Setup time
0.5 µs (2 cycles) < Hold time
Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the number of φ cycles.
To meet the 10-bit addressing format, set the 10BIT SAD bit of the
I2C control register (address 00DA16) to “1.” An address comparison
is made between the first-byte address data transmitted from the
master and the 7-bit slave address stored in the I2C address register
(address 00D816). At the time of this comparison, an address comparison between the RBW bit of the I2C address register (address
00D816) and the R/W bit which is the last bit of the address data
transmitted from the master is made. In the 10-bit addressing mode,
the R/W bit which is the last bit of the address data not only specifies
the direction of communication for control data but also is processed
as an address data bit.
When the first-byte address data matches the slave address, the
AAS bit of the I2C status register (address 00D916) is set to “1.” After
the second-byte address data is stored into the I2C data shift register
(address 00D716), make an address comparison between the second-byte data and the slave address by software. When the address
data of the 2nd bytes matches the slave address, set the RBW bit of
the I2C address register (address 00D816) to “1” by software. This
processing can match the 7-bit slave address and R/W data, which
are received after a RESTART condition is detected, with the value
of the I2C address register (address 00D816). For the data transmission format when the 10-bit addressing format is selected, refer to
Figure 8.6.12, (3) and (4).
Rev. 1.0
40
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.10 Example of Master Transmission
8.6.11 Example of Slave Reception
An example of master transmission in the standard clock mode, at
the SCL frequency of 100 kHz and in the ACK return mode is shown
below.
➀ Set a slave address in the high-order 7 bits of the I2C address
register (address 00D816 ) and “0” in the RBW bit.
➁ Set the ACK return mode and SCL = 100 kHz by setting “8516” in
the I2C clock control register (address 00DB16).
➂ Set “1016” in the I2C status register (address 00D916) and hold the
SCL at the HIGH.
➃ Set a communication enable status by setting “4816” in the I 2C
control register (address 00DA16).
➄ Set the address data of the destination of transmission in the highorder 7 bits of the I2C data shift register (address 00D716) and set
“0” in the least significant bit.
➅ Set “F016” in the I2C status register (address 00D916 ) to generate
a START condition. At this time, an SCL for 1 byte and an ACK
clock automatically occurs.
➆ Set transmit data in the I2C data shift register (address 00D716 ).
At this time, an SCL and an ACK clock automatically occurs.
➇ When transmitting control data of more than 1 byte, repeat step ➆.
➈ Set “D016” in the I 2C status register (address 00D916). After this, if
ACK is not returned or transmission ends, a STOP condition will
be generated.
An example of slave reception in the high-speed clock mode, at the
SCL frequency of 400 kHz, in the ACK non-return mode, using the
addressing format, is shown below.
➀ Set a slave address in the high-order 7 bits of the I 2C address
register (address 00D816) and “0” in the RBW bit.
➁ Set the no ACK clock mode and SCL = 400 kHz by setting “25 16”
in the I2C clock control register (address 00DB16).
➂ Set “1016” in the I2C status register (address 00D916 ) and hold the
SCL at the HIGH.
➃ Set a communication enable status by setting “4816” in the I 2C
control register (address 00DA16).
➄ When a START condition is received, an address comparison is
made.
➅ •When all transmitted address are“0” (general call):
AD0 of the I2 C status register (address 00D916 ) is set to “1”and
an interrupt request signal occurs.
•When the transmitted addresses match the address set in ➀:
ASS of the I2C status register (address 00D9 16) is set to “1” and
an interrupt request signal occurs.
•In the cases other than the above:
AD0 and AAS of the I2C status register (address 00D916) are set
to “0” and no interrupt request signal occurs.
➆ Set dummy data in the I2C data shift register (address 00D716).
➇ When receiving control data of more than 1 byte, repeat step ➆.
➈ When a STOP condition is detected, the communication ends.
Rev. 1.0
41
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
S
Slave address R/W
A
Data
A
Data
A/A
P
A
P
Data
A
7 bits
“0”
1 to 8 bits
1 to 8 bits
(1) A master-transmitter transmits data to a slave-receiver
S
Slave address R/W
A
Data
A
Data
7 bits
“1”
1 to 8 bits
1 to 8 bits
(2) A master-receiver receives data from a slave-transmitter
S
Slave address
R/W
1st 7 bits
A
Slave address
2nd byte
A
Data
A/A
P
7 bits
“0”
8 bits
1 to 8 bits
1 to 8 bits
(3) A master-transmitter transmits data to a slave-receiver with a 10-bit address
S
Slave address
R/W
1st 7 bits
A
Slave address
2nd byte
A
Sr
Slave address
R/W
1st 7 bits
Data
7 bits
“0”
8 bits
7 bits
“1” 1 to 8 bits
(4) A master-receiver receives data from a slave-transmitter with a 10-bit address
S : START condition
A : ACK bit
Sr : Restart condition
P : STOP condition
R/W : Read/Write bit
A
Data
A
P
1 to 8 bits
From master to slave
From slave to master
Fig. 8.6.12 Address Data Communication Format
8.6.12 Precautions when using multi-master
I2C-BUS interface
(2) START condition generating procedure using multi-master
(1) Read-modify-write instruction
➀Procedure example (The necessary conditions of the generating
procedure are described as the following ➁ to ➄).
The precautions when the raead-modify-write instruction such as SEB,
CLB etc. is executed for each register of the multi-master I2C-BUS
interface are described below.
•I2C data shift register (S0)
When executing the read-modify-write instruction for this register
during transfer, data may become a value not intended.
•I2C address register (S0D)
When the read-modify-write instruction is executed for this register
at detecting the STOP condition, data may become a value not
______
intended. It is because hardware changes the read/write bit (RBW)
at the above timing.
•I2C status register (S1)
Do not execute the read-modify-write instruction for this register
because all bits of this register are changed by hardware.
•I2C control register (S1D)
When the read-modify-write instruction is executed for this register
at detecting the START condition or at completing the byte transfer,
data may become a value not intended. Because hardware changes
the bit counter (BC0–BC2) at the above timing.
•I2C clock control register (S2)
The read-modify-write instruction can be executed for this register.
•
•
—
LDA
SEI
BBS 5,S1,BUSBUSY
BUSFREE:
STA S0
LDM #$F0, S1
CLI
•
•
BUSBUSY:
CLI
•
•
(Taking out of slave address value)
(Interrupt disabled)
(BB flag confirming and branch process)
(Writing of slave address value)
(Trigger of START condition generating)
(Interrupt enabled)
(Interrupt enabled)
➁Use “STA,” “STX” or “STY” of the zero page addressing instruction
for writing the slave address value to the I 2C data shift register.
➂Use “LDM” instruction for setting trigger of START condition generating.
➃Write the slave address value of above ➁ and set trigger of START
condition generating of above ➂ continuously shown the above
procedure example.
➄Disable interrupts during the following three process steps:
• BB flag confirming
• Writing of slave address value
• Trigger of START condition generating
When the condition of the BB flag is bus busy, enable interrupts
immediately.
Rev. 1.0
42
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(3) RESTART condition generating procedure
(4) STOP condition generating procedure
➀Procedure example (The necessary conditions of the generating
procedure are described as the following ➁ to ➅.)
Execute the following procedure when the PIN bit is “0.”
➀Procedure example (The necessary conditions of the generating
procedure are described as the following ➁ to ➃.)
LDM
LDA
SEI
STA
LDM
CLI
•
•
#$00, S1
—
S0
#$F0, S1
•
•
(Select slave receive mode)
(Taking out of slave address value)
(Interrupt disabled)
(Writing of slave address value)
(Trigger of RESTART condition generating)
(Interrupt enabled)
•
•
➁Select the slave receive mode when the PIN bit is “0.” Do not write
“1” to the PIN bit. Neither “0” nor “1” is specified for the writing to
the BB bit.
The TRX bit becomes “0” and the SDA pin is released.
➂The SCL pin is released by writing the slave address value to the
I2C data shift register. Use “STA,” “STX” or “STY” of the zero page
addressing instruction for writing.
➃Use “LDM” instruction for setting trigger of RESTART condition generating.
➄Write the slave address value of above ➂ and set trigger of RESTART condition generating of above ➃ continuously shown the
above procedure example.
➅Disable interrupts during the following two process steps:
• Writing of slave address value
• Trigger of RESTART condition generating
SEI
LDM #$C0, S1
NOP
LDM #$D0, S1
CLI
•
•
(Interrupt disabled)
(Select master transmit mode)
(Set NOP)
(Trigger of STOP condition generating)
(Interrupt enabled)
➁Write “0” to the PIN bit when master transmit mode is select.
➂Execute “NOP” instruction after setting of master transmit mode.
Also, set trigger of STOP condition generating within 10 cycles after selecting of master trasmit mode.
➃Disable interrupts during the following two process steps:
• Select of master transmit mode
• Trigger of STOP condition generating
(5) Writing to I 2C status register
Do not execute an instruction to set the PIN bit to “1” from “0” and an
instruction to set the MST and TRX bits to “0” from “1” simultaneously.
It is because it may enter the state that the SCL pin is released and
the SDA pin is released after about one machine cycle. Do not execute an instruction to set the MST and TRX bits to “0” from “1” simultaneously when the PIN bit is “1.” It is because it may become the
same as above.
(6) Process of after STOP condition generating
Do not write data in the I 2C data shift register S0 and the I2 C status
register S1 until the bus busy flag BB becomes “0” after generating
the STOP condition in the master mode. It is because the STOP
condition waveform might not be normally generated. Reading to the
above registers do not have the problem.
Rev. 1.0
43
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.7 PWM OUTPUT FUNCTION
This microcomputer is equipped with two 14-bit PWMs (DA1, DA2)
and six 8-bit PWMs (PWM0–PWM5). DA1 and DA2 have a 14-bit
resolution with the minimum resolution bit width of 0.25 µs and a
repeat period of 4096 µs (for f(XIN) = 8 MHz). PWM0–PWM5 have
the same circuit structure and an 8-bit resolution with minimum resolution bit width of 4 µs and repeat period of 1024 µs (for f(XIN) = 8
MHz).
Figure 8.7.1 shows the PWM block diagram. The PWM timing generating circuit applies individual control signals to DA1, DA2 and
PWM0–PWM5 using f(XIN) divided by 2 as a reference signal.
8.7.1 Data Setting
When outputting DA1, first set the high-order 8 bits to the DA1-H
register (address 00CE16), then the low-order 6 bits to the DA1-L
register (address 00CF16). When outputting DA1, first set the highorder 8 bits to the DA2-H register (address 024E16), then the loworder 6 bits to the DA2-L register (address 024F16). When outputting
PWM0–PWM5, set 8-bit output data to the PWMi register (i means 0
to 5; addresses 00D016 to 00D416, 00F616).
8.7.2 Transferring Data from Registers to PWM
Circuit
Data transfer from the 8-bit PWM register to the 8-bit PWM circuit is
executed at writing data to the register.
The signal output from the 8-bit PWM output pin corresponds to the
contents of this register.
Also, data transfer from the DA1 register (addresses 00CE16 and
00CF16) to the 14-bit PWM circuit is executed at writing data to the
DA1-L register (address 00CF16). Reading from the DA1-H register
(address 00CE16) means reading this transferred data. Data transfer from the DA2 register (addresses 024E16 and 024F16) to the 14bit PWM circuit is executed at writing data to the DA2-L register (address 024F16). Reading from the DA2-H register (address 024E16)
means reading this transferred data. Accordingly, it is possible to
confirm the data being output from the DAi (i = 1, 2) output pin by
reading the DAi (i = 1, 2) register.
8.7.3 Operating of 8-bit PWM
The following explains PWM operation.
First, set the bit 0 of PWM output control register 1 (address 00D516)
to “0” (at reset, bit 0 is already set to “0” automatically), so that the
PWM count source is supplied.
PWM0–PWM5 are also used as pins P00–P05, respectively. For
PWM0–PWM5, set the corresponding bits of the ports P0 direction
register to “1” (output mode). And select each output polarity by bit 3
of PWM output control register 2 (address 00D616). Then, set bits 2
to 7 of PWM output control register 1 to “1” (PWM output).
The PWM waveform is output from the PWM output pins by setting
these registers.
Figure 8.7.2 shows the 8-bit PWM timing. One cycle (T) is composed of 256 (28) segments. The 8 kinds of pulses, relative to the
weight of each bit (bits 0 to 7), are output inside the circuit during 1
cycle. Refer to Figure 8.7.2 (a). The 8-bit PWM outputs waveform
which is the logical sum (OR) of pulses corresponding to the contents of bits 0 to 7 of the 8-bit PWM register. Several examples are
shown in Figure 8.7.2 (b). 256 kinds of output (HIGH area: 0/256 to
255/256) are selected by changing the contents of the PWM register.
A length of entirely HIGH output cannot be output, i.e. 256/256.
8.7.4 Operating of 14-bit PWM
For DA1, as with 8-bit PWM, set the bit 0 of PWM output control
register 1 (address 00D516) to “0” (at reset, bit 0 is already set to “0”
automatically), so that the PWM count source is supplied. Next, select the output polarity by bit 2 of PWM output control register 2 (address 00D616). Then, the 14-bit PWM outputs from the DA1 output
pin by setting bit 1 of PWM output control register 1 to “0” (at reset,
this bit already set to “0” automatically) to select the DA1 output.
For DA2 as with DA1, set the bit 0 of PWM output control register 1
(address 00D516) to “0” (at reset, bit 0 is already set to “0” automatically), so that PWM count source is supplied. Next, select the output
polarity by bit 4 of PWM output control register 2 (address 00D616).
Then, the 14-bit PWM outputs from the DA2 output pin by setting
bit 5 of PWM output control register 1 to “0” (at reset, this bit already
set to “0” automatically) to select the DA2 output.
The output example of the 14-bit PWM is shown in Figure 8.7.3.
The 14-bit PWM divides the data of the DAi latch (i = 1, 2) into the
low-order 6 bits and the high-order 8 bits.
The fundamental waveform is determined with the high-order 8-bit
data “DH.” A HIGH area with a length t ✕ DH (HIGH area of fundamental waveform) is output every short area of “t” = 256τ =
64 µs (τ is the minimum resolution bit width of 250 ns). The HIGH
level area increase interval (tm) is determined with the low-order 6-bit
data “DL.” The HIGH are of smaller intervals “tm” shown in Table 5 is
longer by t than that of other smaller intervals in PWM repeat period
“T” = 64t. Thus, a rectangular waveform with the different HIGH width
is output from the DAi pins (i = 1, 2). Accordingly, the PWM output
changes by τ unit pulse width by changing the contents of the DAi-H
and DAi-L registers (i = 1, 2). A length of entirely HIGH cannot be
output, i. e. 256/256.
8.7.5 Output after Reset
At reset, the output of ports P00–P05 and P17 are in the high-impedance state, and the contents of the PWM register and the PWM
circuit are undefined. Note that after reset, the PWM output is undefined until setting the PWM register.
Table 8.7.1 Relation Between the Low-order 6-bit Data and Highlevel Area Increase Interval
Low-order 6 bits of Data Area Longer by τ than That of Other tm (m = 0 to 63)
LSB
000000
000001
Nothing
000010
m = 16, 48
000100
m = 8, 24, 40, 56
001000
m = 4, 12, 20, 28, 36, 44, 52, 60
010000
m = 2, 6, 10, 14, 18, 22, 26, 30, 34, 38, 42, 46, 50, 54, 58, 62
100000
m = 1, 3, 5, 7, ................................. 57, 59, 61, 63
m = 32
Rev. 1.0
44
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Data bus
DA1-H register
(Address 00CE16)
b7
b0
DA1-L register (See note)
(Address 00CF16)
DA1 latch
(14 bits)
MSB
LS B
6
8
14
6
P35
PN2
DA1
14-bit PWM circuit
PW1
DA2-H register
(A ddress 024E16 )
b7
b0
DA2-L register (See note)
(Address 024F16)
DA2 latch
(14 bits)
MSB
LS B
6
8
14
6
PN4
DA2
14-bit PWM circuit
PW1
PWM timing
generating
circuit
1/2
XIN
P17
PW0
PWM register
(Addre ss 00 D0 16)
b7
b0
8
PN3
8-bit PWM circuit
Selection gate:
Connected to black
side at reset.
Pass gate
Inside of
with the others.
is as same contents
PW: PWM mode register 1 [address 00D516]
PN : PWM mode register 2 [address 00D616]
D0 : Port P0 direction register [address 00C116]
P0 : Port P0 register [address 00C016]
P1 : Port P1 register [address 00C216]
P3 : Port P3 register [address 00C416]
PWM1 register
(Address 00D116)
P00
D00
PWM0
PW2
P01
D01
PWM1
D02
PWM2
D03
PWM3
D04
PWM4
D05
PWM5
PW3
P02
PWM2 register
(Address 00D216)
PW4
P03
PWM3 register
(Address 00D316)
PW5
P04
PWM4 register
(Address 00D416)
PWM5 register
(Address 00F616)
PW6
P05
PW7
Note: DAi-L register is also used as low-order 6 bits of DAi latch (i = 1, 2).
Fig. 8.7.1 PWM Block Diagram
Rev. 1.0
45
46
FF16 (255)
1816 (24)
0116 (1)
0016 (0)
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
t
2
4
8
12
6 10 14
1 3579
16
18
20
26
24
22
20
28
32
36
42
40
40
30 34 38
30
44
48
46 50
56
54 58
52
50
60
64
62 66
60
68
72
70 74
70
76
78
110
120
130
140
150
96
104
108
112
120
116
124
128
136
132
144
140
152
148
156
(b) Example of 8-bit PWM
t = 4 µs T = 1024 µs
f(XIN) = 8 MHz
T = 256 t
(a) Pulses showing the weight of each bit
88
100
PWM output
80
84
100
160
170
180
190
200
210
220
230
240
250 255
160
168
164
172
176
184
180
188
192
200
196
216
212
208
204
224
220
232
228
236
240
248
244
252
94 98 102 106 110 114 118 122 126 130 134 138 142 146 150 154 158 162 166 170 174 178 182 186 190 194 198 202 206 210 214 218 222 226 230 234 238 242 246 250 254
92
90
82 86 90
80
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Fig. 8.7.2 PWM Timing
Rev. 1.0
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Set “2816” to DAi-L register.
Set “2C16” to DAi-H register.
b7 b6 b5 b4 b3 b2 b1 b0
b7 b6 b5 b4 b3 b2 b1 b0
[DAi-H
0 0 1 0 1 1 0 0 DH
register]
[DAi-L register]
b13
0
b6 b5
0
1
0
1
1
0
0
These bits decide HIGH level area
of fundamental waveform.
HIGH level area of
fundamental waveform
Fundamental
waveform
Minimum
resolution bit
width 0.25 µs
✕
0
1
0
0
0
DL
At writing of DAi-L
At writing of DAi-L
[DAi latch]
1
1
b0
0
1
0
0
0
These bits decide smaller interval “tm” in which HIGH leval
area is [HIGH level area of fundamental waveform + τ ].
High-order 8-bit
value of DAi latch
Waveform of smaller interval “tm” specified by low-order 6 bits
0.25 µs✕44
0.25 µs✕45
0.25 µs
14-bit
… 03 02 01 00
PWM output 2C 2B 2A
14-bit
… 03 02 01 00
PWM output 2C 2B 2A
8-bit
counter
8-bit
counter
FF FE FD … D6 D5 D4 D3 … 02 01 00
FF FE FD … D6 D5 D4 D3 … 02 01 00
Fundamental waveform of smaller interval
“tm” which is not specified by low-order 6
bits is not changed.
0.25 µs✕44
τ = 0.25 µs
14-bit PWM output
t0
t1
t2
t3
t4
t5
t59
t60
t61
t62
t63
Low-order 6-bit output of
DAi latch
Repeat period
T = 4096 µs @
Note: i indicates 0 or 1.
Fig. 8.7.3 14-bit PWM Timing (f(XIN) = 8 MHz)
Rev. 1.0
47
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
PWM Output Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0
PWM output control register 1 (PW) [Address 00D516]
B
Name
Functions
0 : Count source supply
0 DA1, DA2, PWM count
source selection bit (PW0) 1 : Count source stop
0 : DA1 output
1 DA1 output/P35
1 : P35 output
selection bit (PW1)
After reset R W
0
R W
0
R W
2 P00/PWM0 output
selection bit (PW2)
0: P00 output
1: PWM0 output
0
R W
3 P01/PWM1 output
selection bit (PW3)
0: P01 output
1: PWM1 output
0
R W
4 P02/PWM2 output
selection bit (PW4)
0: P02 output
1: PWM2 output
0
R W
5 P03/PWM3 output
selection bit (PW5)
0: P03 output
1: PWM3 output
0
R W
6 P04/PWM4 output
selection bit (PW6)
0: P04 output
1: PWM4 output
0
R W
7 P05/PWM5 output
selection bit (PW7)
0: P05 output
1: PWM5 output
0
R W
Fig. 8.7.4 PWM Output Control Register 1
PWM Output Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0 0
0 0
PWM output control register 2 (PN) [Address 00D616]
B
Name
0, 1 Fix these bits to “0.”
Functions
After reset R W
0
R W
2 DA1 output polarity
selection bit (PN3)
0 : Positive polarity
1 : Negative polarity
0
R W
3 PWM output polarity
selection bit (PN4)
0 : Positive polarity
1 : Negative polarity
0
R W
4 DA2 output polarity
selection bit (PN5)
0 : Output LOW
1 : Output HIGH
0
R W
5 P17/DA2 output
selection bit (PN5)
0 : P17
1 : DA2
0
R W
0
R W
6, 7 Fix these bits to “0.”
Fig. 8.7.5 PWM Output Control Register 2
Rev. 1.0
48
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.8 A-D CONVERTER
8.8.1 A-D Conversion Register (AD)
8.8.3 Comparison Voltage Generator (Resistor
Ladder)
A-D conversion reigister is a read-only register that stores the result
of an A-D conversion. This register should not be read during A-D
conversion.
The voltage generator divides the voltage between VSS and VCC by
256, and outputs the divided voltages to the comparator as the reference voltage Vref.
8.8.2 A-D Control Register (ADCON)
8.8.4 Channel Selector
The A-D control register controls A-D conversion. Bits 2 to 0 of this
register select analog input pins. When these pins are not used as
anlog input pins, they are used as ordinary I/O pins. Bit 3 is the A-D
conversion completion bit, A-D conversion is started by writing “0” to
this bit. The value of this bit remains at “0” during an A-D conversion,
then changes to “1” when the A-D conversion is completed.
Bit 4 controls connection between the resistor ladder and VCC. When
not using the A-D converter, the resistor ladder can be cut off from
the internal VCC by setting this bit to “0,” accordingly providing lowpower dissipation.
The channel selector connects an analog input pin, selected by bits
2 to 0 of the A-D control register, to the comparator.
8.8.5 Comparator and Control Circuit
The conversion result of the analog input voltage and the reference
voltage “Vref” is stored in the A-D conversion register. The A-D conversion completion bit and A-D conversion interrupt request bit are
set to “1” at the completion of A-D conversion.
Data bus
b7
b0
A-D control register
(address 00DF16)
3
A-D conversion
interrupt request
A-D control circuit
A-D1
Comparator
A-D3
A-D4
A-D5
A-D6
Channel selector
A-D2
A-D conversion register
8
(address 00DE16)
Switch tree
Resistor ladder
A-D7
A-D8
VSS VCC
Fig. 8.8.1 A-D Converter Block Diagram
Rev. 1.0
49
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
A-D Control Register
b7 b6 b5 b4 b3 b2 b1 b0
0
0
A-D control register (ADCON) [Address 00DF16]
B
Name
Functions
After reset R W
0
R W
0: Conversion in progress
1: Convertion completed
1
R W
0: OFF
1 : ON
0
R W
0
R W
Indeterm inate
R —
0
R W
0
to
2
Analog input pin selection
bits
(ADIN0 to ADIN2)
b2
0
0
0
0
1
1
1
1
b1
0
0
1
1
0
0
1
1
b0
0 : A-D1
1 : A-D2
0 : A-D3
1 : A-D4
0 : A-D5
1 : A-D6
0 : A-D7
1 : A-D8
3
A-D conversion completion
bit (ADSTR)
4
VCC connection selection bit
(ADVREF)
5
Fix this bit to “0.”
6
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is indeterminate.
7
Fix this bit to “0.”
Fig. 8.8.2 A-D Control Register
Rev. 1.0
50
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.8.6 Conversion Method
8.8.7 Internal Operation
➀ Set the A-D conversion interrupt request bit to “0” (even when AD conversion is started, the A-D conversion interrupt reguest bit
is not set to “0” automatically).
➁ When using A-D conversion interrupt, enable interrupts by setting
A-D conversion interrupt enable bit to “1” and setting the interrupt
disable flag to “0.”
➂ Set the VCC connection selection bit to “1” to connect VCC to the
resistor ladder.
√ Select analog input pins by the analog input selection bit of the
A-D control register.
➄ Set the A-D conversion completion bit to “0.” This write operation
starts the A-D conversion. Do not read the A-D conversion register during the A-D conversion.
≈ Verify the completion of the conversion by the state (“1”) of the
A-D conversion completion bit, the state (“1”) of A-D conversion
interrupt reguest bit, or the occurrence of an A-D conversion interrupt.
∆ Read the A-D conversion register to obtain the conversion results.
When the A-D conversion starts, the following operations are automatically performed.
➀ The A-D conversion register is set to “0016.”
➁ The most significant bit of the A-D conversion register becomes
“1, ” and the comparison voltage “Vref” is input to the comparator. At
this point, Vref is compared with the analog input voltage “VIN .”
➂ Bit 7 is determined by the comparison results as follows.
When Vref < VIN : bit 7 holds “1”
When Vref > VIN : bit 7 becomes “0”
With the above operations, the analog value is converted into a digital
value. The A-D conversion terminates in a maximum of 50 machine
cycles (8.5 µs at f(XIN) = 8 MHz) after it starts, and the conversion
result is stored in the A-D conversion register.
An A-D conversion interrupt request occurs at the same time as A-D
conversion completion, the A-D conversion interrupt request bit becomes “1.” The A-D conversion completion bit also becomes “1.”
Note : When the ladder resistor is disconnect from VCC, set the VCC connection selection bit to “0” between steps ≈ and ∆ .
Table 8.8.1 Expression for Vref and VREF
A-D conversion register contents “n”
(decimal notation)
0
Vref (V)
0
VREF
~(n |0.5)
256
1 to 255
Note: VREF indicates the reference voltage (= Vcc).
Contents of A-D conversion register
A-D conversion start
0 0 0 0 0
1st comparison start
1 0 0 0 0 0 0 0
2nd comparison start
1 1 0 0 0 0 0 0
3rd comparison start
1 2 1 0 0 0 0 0
8th comparison start
1 2 3 4 5 6 7 1
A-D conversion completion
1 2 3 4 5 6 7 8
(8th comparison completion)
Reference voltage (Vref) [V]
0 0 0
0
VREF
–
2
VREF
±
2
VREF ±
2
VREF
512
VREF VREF
–
4
512
VREF ± VREF
VREF
–
4
8
512
VREF ± VREF ± VREF ± .....
2
4
8
....... ± VREF – VREF
512
256
Digital value corresponding to
analog input voltage.
m
: Value determined by mth (m = 1 to 8) result
Fig. 8.8.3 Changes in A-D Conversion Register and Comparison Voltage during A-D Conversion
Rev. 1.0
51
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.8.8 Definition of A-D Conversion Accuracy
The definition of A-D conversion accuracy is described below (refer
to Figure 8.8.4).
• EDifferential non-linearity error
The deviation of the input voltage required to change output data
by “1,” from the corresponding ideal A-D conversion characteristics between 0 and VREF.
(1) Relative Accuracy
•Zero transition error (V0T)
The deviation of the input voltage at which A-D conversion output
data changes from “0” to “1,” from the corresponding ideal A-D
conversion characteristics between 0 and VREF.
V0T =
1LSB
[LSB]
(2) Absolute Accuracy
[LSB]
• Full-scale transition error (VFST)
The deviation of the input voltage at which A-D conversion output
data changes from “255” to “254,” from the corresponding ideal AD conversion characteristics between 0 and VREF.
VFST =
(Vn+1 – Vn) – 1LSB
• EAbsolute accuracy error
The deviation of the actual A-D conversion characteristics, from the
ideal A-D conversion characteristics between 0 and VREF.
(V0 – 1/2 ✕ VREF/256)
1LSB
Differential non-linearity error =
Vn – 1LSBA ✕ (n + 1/2)
Absolute accuracy error =
[LSB]
1LSBA
(VREF – 3/2 ✕ VREF/256) – V254
[LSB]
1LSB
Note: The analog input voltage “Vn” at which A-D conversion output data
changes from “n” to “n + 1” (n ; 0 to 254) is as follows (refer to Figure
8.8.4) :
• Non-linearity error
The deviation of the actual A-D conversion characteristics, from the
ideal A-D conversion characteristics between V0 and V254.
Non-linearity error =
Vn – (1LSB ✕ n + V0)
[LSB]
1LSB
1LSB with respect to relative accuracy =
V254 – V0
254
[V]
VREF
1LSBA with respect to absolute accuracy =
256
[V]
Output code
0916
0816
Absolute accuracy
+ 2LSB
0716
Ideal A-D conversion
characteristics
0616
Limitless resolution A-D
conversion characteristics
0516
0416
0316
– 2LSB
0216
0116
0016
0
20
40
60
80
100 120 140 160
180 200 220
Analog input voltage (mV)
Fig. 8.8.4 Definition of A-D Conversion Accuracy
Rev. 1.0
52
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.9 ROM CORRECTION FUNCTION
This can correct program data in ROM. Up to 3 addresses can be
corrected, a program for correction is stored in the ROM correction
vector in RAM as the top address. The ROM correction vectors are 3
vectors.
Vector 1 : address 02C016
Vector 2 : address 02E016
Vector 3 : address 030016
Set the address of the ROM data to be corrected into the ROM correction address register. When the value of the counter matches the
ROM data address in the ROM correction vector as the top address,
the main program branches to the correction program stored in the
ROM memory for correction. To return from the correction program
to the main program, the op code and operand of the JMP instruction
(total of 3 bytes) are necessary at the end of the correction program.
The ROM correction function is controlled by the ROM correction
enable register.
Notes 1: S p e c i f y t h e f i r s t a d d r e s s ( o p c o d e a d d r e s s ) o f e a c h
instruction as the ROM correction address.
2: Use the JMP instruction (total of 3 bytes) to return from
the correction program to the main program.
3: Do not set the same ROM correction address to vectors 1 to 3.
ROM correction address 1 (high-order) 021716
ROM correction address 1 (low-order)
021816
ROM correction address 2 (high-order) 021916
ROM correction address 2 (low-order)
021A16
ROM correction address 3 (high-order) 021C16
ROM correction address 3 (low-order)
021D16
Fig. 8.9.1 ROM Correction Address Registers
ROM Correction Enable Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0 0 0 0
ROM correction enable register (RCR) [Address 021B16]
B
Name
Functions
After reset R W
0
Vector 1 enable bit (RCR0)
0: Disabled
1: Enabled
0
R W
1
Vector 2 enable bit (RCR1)
0: Disabled
1: Enabled
0
R W
2
Vector 3 enable bit (RCR2)
0: Disabled
1: Enabled
0
R W
3
to
7
Fix these bits to “0.”
0
R W
Fig. 8.9.2 ROM Correction Enable Register
Rev. 1.0
53
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10 OSD FUNCTIONS
This OSD function can display the following 3 types:
• “Block display ” (24 characters ✕ 2 lines)
• “SPRITE display” (display only a character) or “Raster patterning
display” (display a character on entire screen side by side)
• “Raster flat display” (coloring entire screen)
The above displays can be overlapped at the same time. The priority
is :
SPRITE display > Block display > Raster flat display
or
Block display > Raster patterning display > Raster flat display
Note that raster patterning display and SPRITE display cannot be
used simultaneously.
Figure 8.10.2 shows the block diagram of OSD circuit, Figure 8.10.3
shows the configuration of OSD character display area, Figure 8.10.4
shows the OSD control register.
Di spla y Type
OSD
Function
Di sp la y M od e
SPRITE display
(see note)
Block display
OSD mode
(See note)
Dis p la y Le ve l
( Dis pla y Priorit y)
Int errupt
R eques t
SPRITE OSD interrupt
Top
—
Middle
Top
OSD interrupt
—
Middle
—
Bottom
Bottom
—
All bordered
Shadow bordered
BUTTON mode
All bordered
Shadow bordered
Raster patterning display (See note)
Raster flat display
Note: Raster patterning display and SPRITE display cannot be used simultaneously.
Fig. 8.10.1 Display Types of OSD Function
Rev. 1.0
54
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Clock for OSD
HSYNC VSYNC
OSC1
Main clock
XIN
Display
ocsillation
circuit
Control registers for OSD
OSD control circuit
OSD port control register
Interrupt input polarity register
Block H register
Block i V register
SPRITE control register
SPRITE H register
SPRITE V register
Color register i
OSD control register
OSD I/O polarity register
Block i control register
Left border register
Right border register
Top border register
Bottom border register
OSD RAM
15 bits ✕ 24 characters ✕
2 lines
(Address 00CB16)
(Address 00CD16)
(Address 00E016)
(Addresses 00E116, 00E216)
(Address 00E316 j
(Address 00E416)
(Address 00E516)
(Addresses 00E616 to 00E916,
00EC16 to 00EF16)
(Address 00EA16)
(Address 00EB16)
(Addresses 00F916, 00FA16)
(Address 024016)
(Address 024116)
(Address 024516)
(Address 024616)
OSD ROM
1 6 d o ts ✕ 2 0 d o ts ✕
381 characters
Shift register
Output circuit
R
G
B
OUT1
OUT2
Data bus
Fig. 8.10.2 Block Diagram of OSD Circuit
Rev. 1.0
55
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
• SPRITE Display
• Block Display (OSD Mode)
• Block Display (BUTTON Mode)
16 dots
16 dots
20 dots
20 dots
2 d o ts
2 d o ts
: BUTTON display area (displayed only in BUTTON mode j
Fig. 8.10.3 Configuration of OSD Character Display Area
OSD Control Register
b7 b6 b5 b4 b3 b2 b1 b0
OSD control register (OC) [Address 00EA16]
B
0
1
Name
OSD control bit
(OC0) (See note 1)
Border type selection
bit (OC1)
2, 3 Window horizontal
position minute
adjustment bit
(OC2, OC3)
4 Window control bit
(OC4)
Functions
After reset R W
0 : All-blocks display OFF
1 : All-blocks display ON
0 : All bordered
1 : Shadow bordered (See note 2)
0
R W
0
R W
b3
0
0
1
1
0
R W
0
R W
0
R W
b2
(See notes 3 and 4)
0 : Standard
1 : Standard + 1TOSC
0 : Standard + 2TOSC
1 : Standard + 3TOSC
0 : Window OFF
1 : Window ON
5 Scan mode selection 0 : Normal scan mode
bit (OC5)
1 : Bi-scan mode (See note 5)
6 Raster color OUT1
control bit (OC6)
0 : No output
1 : Output
0
R W
7 Raster color OUT2
control bit (OC7)
0 : No output
1 : Output
0
R W
Notes 1 : Even this bit is switched during display, the display screen
remains unchanged until a rising (falling) of the next VSYNC.
2 : Shadow border is output at right and bottom side of the font.
3 : TOSC = OSD oscillation cycle
4 : These bits are vallid for both left border and right border (for detail, refer
to “(8) Window Function.”)
5 : When setting to bi-scan mode, connect LC between pins OSC1 and
OSC2.
Fig. 8.10.4 OSD Control Register
Rev. 1.0
56
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(1) Clock for OSD
As a clock for display to be used for OSD, it is possible to select one
of the following 3 types.
• Main clock from the pins XIN and XOUT
• Clock from the LC or RC oscillator supplied from the pins OSC1
and OSC2
• Clock from the ceramic resonator or the quartz-crystal oscillator
from the pins OSC1 and OSC2
The clock for display to be used for OSD can be selected by bits 0
and 1 of the interrupt input polarity register (address 00CD16).
And besides, when selecting main clock, set the oscillation frequency
to 8 MHz.
Interrupt Input Polarity Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0
0
Interrupt input polarity register (IP) [Address 00CD16]
b
Name
0, 1 OSD clock
selection bits
(OCG0, OCG1)
Function
After reset R W
Function
b1 b0
0 0 The clock for OSD is supplied by connecting RC
or LC across the pins OSC1 and OSC2. However,
it is not corresponding to the bi-scan mode.
0
1 Since the main clock is used as the
clock for OSD, the oscillation
frequency is limited. Because of
this, the character size in width
(horizonal) direction is also limited.
In this case, pins OSC1 and OSC2
are also used as input ports P33
and P34 respectively.
1
0
1
1
0
R W
0
R W
OSD
oscillation
frequency =
f(XIN)
The clock for OSD is supplied by connecting LC
across the pins OSC1 and OSC2. In the bi-scan
mode, be sure to set this.
The clock for OSD is supplied by connecting the
following across the pins OSC1 and OSC2.
However, it is not corresponding to the bi-scan
mode.
• a ceramic resonator only for OSD and a
feedback resistor
• a quartz-crystal oscillator only for OSD and a
feedback resistor
2
Fix this bit to “0.”
3
INT1 polarity
switch bit (POL1)
0 : Positive polarity
1 : Negative polarity
0
R W
4
INT2 polarity
switch bit (POL2)
0 : Positive polarity
1 : Negative polarity
0
R W
5
INT3 polarity
switch bit (POL3)
0 : Positive polarity
1 : Negative polarity
0
R W
0
R W
6, 7 Fix these bits to “0.”
Fig. 8.10.5 Interrupt Input Polarity Register
Rev. 1.0
57
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(2) Scan mode
This microcomputer has the bi-scan mode for corresponding to HSYNC
of double-speed frequency. In the bi-scan mode, the vertical start
display position and the vertical dot size is two times as compared
with the normal scan mode. The scan mode is selected by bit 5 of the
OSD control register (refer to Figure 8.10.3).
Table 8.10.1 Setting for Scan Mode
Scan Mode
Parameter
Bit 5 of OSD Control Register
Vertical Display Start Position
Vertical Dot Size
Normal Scan
Bi-Scan
0
Value of vertical position register ✕ 1H
1TOSC ✕ 1H
2TOSC ✕ 2H
3TOSC ✕ 3H
1
Value of vertical position register ✕ 2H
1TOSC ✕ 2H
2TOSC ✕ 4H
3TOSC ✕ 6H
Notes 1: TOSC = OSD oscillation cycle
2: H = HSYNC
Rev. 1.0
58
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(3) OSD input/output pin control
The OSD output pins R, G, B, OUT1 and OUT2 can also function as
ports P52, P53, P54, P55, P10 respectively. Switch either OSD output function or port function by the OSD port control register (address 00CB16).
The input polarity of the HSYNC, VSYNC and output polarity of signals
R, G, B, OUT1 and OUT2 can be specified with the OSD I/O polarity
register (address 00EB16). Set a bit to “0” to specify positive polarity;
set it to “1” to specify negative polarity.
Figure 8.10.6 shows the OSD I/O polarity register and Figure 8.10.7
shows the OSD port control register.
OSD I/O Polarity Register
b7 b6 b5 b4 b3 b2 b1 b0
OSD I/O polarity register (OPC) [Address 00EB16]
B
Name
Functions
Af t er r e R W
0
HSYNC input polarity
switch bit (OPC0)
0 : Positive polarity input
1 : Negative polarity input
0
R W
1
VSYNC input polarity
switch bit (OPC1)
0 : Positive polarity input
1 : Negative polarity input
0
R W
2
R/G/B output polarity switch 0 : Positive polarity output
1 : Negative polarity output
bit (OPC2)
0
R W
3
OUT1 output polarity
switch bit (OPC3)
0 : Positive polarity output
1 : Negative polarity output
0
R
4
OUT2 output polarity
switch bit (OPC4)
0 : Positive polarity output
1 : Negative polarity output
0
R W
5
Raster color R control
bit (OPC5)
0 : No output
1 : Output
0
R W
6
Raster color G control bit
(OPC6)
0 : No output
1 : Output
0
R W
7
Raster color B control bit
(OPC7)
0 : No output
1 : Output
0
R W
W
Fig. 8.10.6 OSD I/O Polarity Register
OSD Port Control Register
b7 b6 b5 b4 b3 b2 b1 b0
0
0 0
OSD port control register (PF ) [Address 00CB16]
b
Name
Functions
0, 1 Fix these bits to “0”
After reset R W
0
R W
2
Port P52 output signal
selection bit (P52SEL)
0 : R signal output
1 : Port P52 output
0
R W
3
Port P53 output signal
selection bit (P53SEL)
0 : G signal output
1 : Port P53 output
0
R W
4
Port P54 output signal
selection bit (P54SEL)
0 : B signal output
1 : Port P54 output
0
R W
5
Port P55 output signal
selection bit (P55SEL)
0 : OUT1 signal output
1 : Port P55 output
0
R W
6
Port P10 output signal
selection bit (OUT2SEL)
0 : Port P10 signal output
1 : OUT2 output
0
R W
7
Fix this bit to “0”
0
R W
Fig. 8.10.7 OSD Port Control Register
Rev. 1.0
59
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.1 Block Display
There are 2 display modes and they are selected by a block unit. The
display modes are selected by bits 0 to 2 of block i control register (i
= 1, 2).
The features of each mode are described below.
There are an extended display mode. This mode allows multiple lines
(3 lines or more) to be displayed on the screen by interrupting the
display each time one line is displayed and rewriting data in the block
for which display is terminated by software.
Table 8.10.2 Features of Each Display Style of Block Display
Block display
Display style
Display mode
Parameter
OSD mode
(On-screen display mode)
BUTTON mode
(BUTTON display mode)
24 characters ✕ 2 lines
Number of display characters
16 ✕ 20 dots
Character display area: (16 dots + 4 dots ) ✕ (20 dots + 4 dots)
16 ✕ 20 dots
Dot structure
Kinds of characters
381 kinds
Kinds of character sizes
3 kinds
1TOSC ✕ 1H, 2TOSC ✕ 2H, 3TOSC ✕ 3H (per block unit) (See notes 1, 2)
Dot size
Attribute
■ Border (per block unit)
■ BUTTON display (per character unit)
■ Block shadow display (per character unit)
Border (per block unit)
Character font coloring
1 screen: 8 kinds (per character unit)
Character background
coloring
1 screen: 8 kinds (per character unit)
OSD output
R, G, B
Raster coloring
Possible (per screen unit)
■ Corresponding to bi-scan
■ Window function (See note 3)
Other functions
Display position
Horizontal: 64 levels, Vertical: 255 levels
Display expansion
(multiline display)
Possible
Notes 1: TOSC = OSD oscillation cycle
2: H = HSYNC
3: The SPRITE display is not effected by the window function.
Block i Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Block i control register (BiC) (i = 1, 2) [Addresses 00F916, 00FA16]
Functions
After reset
b2 b1 b0
Display mode
Indeterminate
✕ 0 0 Display OFF
0 0 1 OSD mode (no border)
0 1 0 BUTTON mode (no border)
1 0 1 OSD mode (border)
1 1 0 BUTTON mode (border)
Indeterminate
D
o
t
s
i
z
e
s
e
l
e
c
t
i
o
n
b
i
t
b
4 b3
Dot size
3, 4
(BiC3, BiC4)
0 0
1TOSC ✕ 1H
0 1
Do not set
1 0
2TOSC ✕ 2H
1 1
3TOSC ✕ 3H
5 Nothing is assigned. These bits are write disable bits.
0
to When these bits are read out, the values are “0.”
7
B
Name
0 Display mode
to selection bits
2 (BiC0 to BiC2)
R W
R W
R W
R—
Notes 1 : TOSC = OSD oscillation cycle
2 : H = HSYNC
Fig. 8.10.8 Block i Control Register (i = 1, 2)
Rev. 1.0
60
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(1) Display position
The display positions of characters are specified by a block. There
are 2 blocks, blocks 1 and 2. Up to 24 characters can be displayed in
each block (refer to “(3) Memory for OSD”).
The display position of each block can be set in both horizontal and
vertical directions by software.
The display start position in the horizontal direction can be set for all
blocks in common in 64-step display positions in units of 4TOSC (TOSC
= OSD oscillation cycle).
The display start position in the vertical direction for each block can
be set in 255-step display positions in units of 1 H ( H = HSYNC cycle).
Blocks are displayed in conformance with the following rules:
• When the display position of block 1 is overlapped with block 2
(Figure 8.10.9 (b)), block 1 is displayed on the front.
• When another block display position appears while one block is .
displayed (Figure 8.10.9 (c)), the block with a larger set value as
the vertical display start position is displayed.
For the display position of SPRITE display, it is necessary to set independently, and it is possible to set display positions independently.
Refer to “8.10.2 SPRITE Display.”
BHP
B1VP
Block 1
B2VP
Block 2
(a) Example when each block is separated
BHP
B1VP = B2VP
Block 1
(Block 2 is not displayed)
(b) Example when block 2 overlaps with block 1
BHP
B1VP
Block 1
B2VP
Block 2
(c) Example when block 2 overlaps in process of block 1
Notes 1: B1VP or B2VP indicates the vertical display start position of display blocks 1 and 2.
2: BHP indicates the horizontal display start position of display blocks 1 and 2.
Fig. 8.10.9 Display Position
Rev. 1.0
61
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
The vertical display start position is determined by counting the horizontal sync signal (HSYNC). At this time, when VSYNC and HSYNC are
positive polarity (negative polarity), it starts to count the rising edge
(falling edge) of HSYNC signal from after fixed cycle of rising edge
(falling edge) of VSYNC signal. So interval from rising edge (falling
edge) of VSYNC signal to rising edge (falling edge) of HSYNC signal
needs enough time (2 machine cycles or more) for avoiding jitter.
The polarity of HSYNC and VSYNC signals can select with the OSD I/
O polarity register (address 00EB16).
8 machine cycles or more
VSYNC signal input
0.25 to 0.50 [µs]
( at f(XIN) = 8MHz)
VSYNC control
signal in
microcomputer
Period of counting
HSYNC signal
(See note 2)
HSYNC
signal input
8 machine cycles
or more
1
2
3
4
5
Not count
When bits 0 and 1 of the I/O polarity control register
(address 00EB16) are set to “1” (negative polarity)
Notes 1 : The vertical position is determined by counting falling edge of
HSYNC signal after rising edge of VSYNC control signal in the
microcomputer.
2 : Do not generate falling edge of HSYNC signal near rising edge
of VSYNC control signal in microcomputer to avoid jitter.
3 : The pulse width of VSYNC and HSYNC needs 8 machine cycles
or more.
Fig. 8.10.10 Supplement Explanation for Display Position
The vertical display start position for each block can be set in 255
steps (where each step is 1H (H: HSYNC cycle)) as values “0116” to
“FF16” in block i V register (i = 1, 2) (addresses 00E116 to 00E216).
When setting the block i V register to “0116,” the display is started at
18H of count value of HSYNC signal. The vertical display start position here indicates the top position of character display area in OSD/
BUTTON mode.
The block i V register is shown in Figures 8.10.11.
Block i V Register
b7 b6 b5 b4 b3 b2 b1 b0
Block i V register (BiVP) (i = 1, 2) [Addresses 00E116 and 00E216]
B
Name
Functions
0 Control bits of
Vertical display start positions = Hdef + H ✕ n
to vertical display
(n: setting value, Hdef: 17H, H: HSYNC)
7 start positions
(BiVP0 to BiVP7)
(See note 1)
After reset R W
Indeterminate R W
Note: Set values except “0016” to BiVP.
Fig. 8.10.11 Block i V Register (i = 1, 2)
Rev. 1.0
62
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
VSYNC
HSYNC
(When setting “0116” to block i V register, vertical display start position for each mode)
1
2
3
screen
Hdef
17
18
Nv
Hdef
NV
Vertical display start position
:Value of block V register i
(decimal)
:17H
OSD mode
BUTTON mode
When bits 0 and 1 of OSD I/O polarity register (address 00EB16) are “1” (negative polarity)
Fig. 8.10.12 Notes on Vertical Display Start Position
The horizontal display start position is common to all blocks, and can
be set in 64 steps (where 1 step is 4TOSC, TOSC being the OSD
oscillation cycle) as values “0016” to “3F16” in the block H register
(address 00E016). The block H register is shown in Figure 8.10.13.
Block H Register
b7 b6 b5 b4 b3 b2 b1 b0
Horizontal position register (HP) [Address 00E016]
B
Name
Functions
0 Control bits of horizontal Horizontal display start positions = Tdef1 + 4TOSC ✕ n
to display start positions (n: setting value, Tdef1: 31TOSC,
5 (BHP0 to BHP5)
TOSC: OSD oscillation cycle)
(See note 1)
6, 7 Nothing is assigned. These bits are write disable bits.
W h en t h e s e b i t s a r e re a d o u t, t h e v a l u e s a r e “0 . ”
After reset R W
0
RW
0
R—
Note: The setting value synchronizes with the VSYNC.
Fig. 8.10.13 Block H Register
Rev. 1.0
63
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
When setting the block H register to “0016,” it needs 31TOSC (= Tdef1)
from a rising edge (negative polarity) of HSYNC signal to horizontal
display start position. The horizontal display start position here indicates the left position of the 1st character’s BUTTON display area in
BUTTON mode. When also changing character size, the horizontal
display start position is the same. In OSD mode, display position is
shifted for BUTTON display area (for 2 dots) from that of the same
character size in BUTTON mode.
Horizontal display start position
HSYNC
BUTTON mode (1TOSC ✕ 1H)
Tdef1
4TOSC ✕ NH
• • •
BUTTON mode (2TOSC ✕ 2H)
NH
: Value of block H register
(decimal)
TOSC : OSD oscillation cycle
Tdef1 : 31TOSC
• • •
BUTTON mode (3TOSC ✕ 3H)
• • •
OSD mode
• • •
Width of BUTTON display area (2 dots)
Fig. 8.10.14 Notes on Horizontal Display Start Position
Rev. 1.0
64
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(2) Dot size
Refer to Figure 8.10.8 (the block i control register).
The block diagram of dot size control circuit is shown in Figure 8.10.15.
The dot size can be selected by a block unit. The dot size in vertical
direction is determined by dividing HSYNC in the vertical dot size control circuit. The dot size in horizontal is determined by dividing the
following clock in the horizontal dot size control circuit : the clock
gained by dividing the OSD clock source (OSC1, main clock from pin
XIN) in the pre-divide circuit.
The dot size is specified by bits 3 and 4 of the block i control register.
Clock cycle
= 1TOSC
OSC1
Synchronous
circuit
Main clock
XIN
Horizontal dot size
control circuit
OCG0 = “1”
OCG1 = “0”
Vertical dot size
control circuit
HSYNC
OSD control circuit
Fig. 8.10.15 Block Diagram of Dot Size Control Circuit
1 dot
1TOSC
3TOSC
2TOSC
1H
2H
3H
Scanning line of F1(F2)
Scanning line of F2(F1)
Fig. 8.10.16 Definition of Dot Sizes
Rev. 1.0
65
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(3) Memory for OSD
There are 2 types of memory for OSD : OSD ROM (addresses 1140016
to 13BFF16 and 1540016 to 17AFF16) used to specify character dot
data and OSD RAM (addresses 080016 to 0877) used to specify the
characters, colors, and attribute. The following describes each type
of memory.
➀ OSD ROM (addresses 1140016 to 13BFF16, 1540016 to 17AFF16)
The dot pattern data for OSD characters is stored in the character font area in the OSD ROM. To specify the kinds of the character font, it is necessary to write the character code (based on
OSD ROM address) into the OSD RAM.
The modes are selected by bit 3 of the OSD control register 3 for
each screen.
The character font data storing address is shown in Figure
8.10.17.
OSD ROM address of character font data
OSD ROM
address bit
Line number /
Character code /
Font bit
AD16 AD15 AD14 AD13 AD12 AD11 AD10
1
0
Ch aracter
cod e
(highorder 1)
AD9
AD8
Line number
AD7
AD6
AD5
AD4
AD3
AD2
Character code (low-order 8 bits)
AD1
AD0
Font
bit
Line number = “0A16” to “1D16”
Character code = “00016” to “17F16” (“07F16”, “08016” and “17F16 ” cannot be used.)
Font bit = 0: Left area
1: Right area
Line
number
b7
Left area
b0 b7
Right area
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
b0
OSD ROM
data
000016
7FF016
7FF816
601C16
600C16
600C16
600C16
600C16
601C16
7FF816
7FF016
630016
638016
61C016
60E016
607016
603816
601C16
600C16
000016
Character font
Fig. 8.10.17 Character Font Data Storing Address
Rev. 1.0
66
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Note: The 120-byte addresses corresponding to the character code “07F16,”
“08016” and “17F16” in OSD ROM are the test data storing area. Set
“FF16” to the area. (We stores the test data to this area and the different
data from “FF16” is stored for the actual products.)
<The test data storing area>
• 1100016 + (4 + 2n) ✕ 10016 + FE16 to 1100016 + (5 + 2n) ✕ 10016 + 0116
• 1500016 + (4 + 2n) ✕ 10016 + FE16 and 1500016 + (4 + 2n) ✕ 10016 + 0116
(n = 0 to 19)
Address area
…
addresses 114FE16 to 1150116
addresses 116FE16 to 1170116
addresses 138FE16 to 1390116
addresses 13AFE16 to 13B0116
addresses 154FE16 and 154FF16
addresses 156FE16 and 156FF16
…















addresses 178FE16 and 178FF16
addresses 17AFE16 and 17AFF16















Table 8.10.3 Contents of OSD RAM
Display Position (from left)
Block
Block 1
Block 2
1st character
2nd character
3rd character
:
16th character
17st character
:
24nd character
1st character
2nd character
3rd character
:
16th character
17st character
:
24nd character
➁ OSD RAM (addresses 080016 to 087716)
The OSD RAM for character is allocated at addresses 0800 16 to
084716, 085016 to 085716, 086016 to 086716, 087016 to 087716, and
is divided into a display character code specification part 087016 to
087716, and color/attribute specification part for each block. Tables
8.10.3 shows the contents of the OSD RAM.
For example, to display 1 character position (the left edge) in block 1,
write the character code in address 080016, write color/attribute code
at 081016.
The structure of the OSD RAM is shown in Figure 8.10.18.
Character Code Specification
Color/Attribute Code Specification
080016
080116
080216
:
080F16
084016
:
084716
082016
082116
082216
:
082F16
086016
:
086716
081016
081116
081216
:
081F16
085016
:
085716
083016
083116
083216
:
083F16
087016
:
087716
Rev. 1.0
67
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Blocks 1 and 2
b7
0
b0 b7
b0
RA6 RA5 RA4 RA3 RA2 RA1 RF8 RF7 RF6 RF5 RF4 RF3 RF2 RF1 RF0
OUT2 control
Attribute code
(See note 1)
Color code
Character code 1 (See note 2)
Mode
OSD Mode
BUTTON Mode
Bit
RF0
Bit name
Function
Character code
Bit name
Function
Character code
Character code
in OSD ROM
RF1
Character code
in OSD ROM
RF2
RF3
RF4
RF5
RF6
RF7
RF8
RA 1
Color code
RA 2
RA 3
RA 4
Attribute code
RA 5
RA 6
OUT2 control
RA3 RA2 RA1
Color code
0
0: Color register 1
0
0
0: Color register 1
0
0
1: Color register 2
0
0
1: Color register 2
0
1
0: Color register 3
0
1
0: Color register 3
0
1
1: Color register 4
0
1
1: Color register 4
1
0
0: Color register 5
1
0
0: Color register 5
1
0
1: Color register 6
1
0
1: Color register 6
1
1
0: Color register 7
1
1
0: Color register 7
1
1
1: Color register 8
1
1
1: Color register 8
RA4 RA4
0
0: No BUTTON/block shadow display
0
1: ON BUTTON display
1
0: OFF BUTTON display
0
1: Block shadow display
0: OUT2 blank output OFF
Not used
OUT2 control
1: OUT2 blank output ON
RA 7
RA3 RA2 RA1
0
Fix to “0”
0: OUT2 blank output OFF
1: OUT2 blank output ON
Fix to “0”
Notes 1: Attribute code is valid in only BUTTON mode.
2: Do not use character codes “07F16,” “08016,” “17F16.”
And also, do not use character codes “18016” to “1FF16” (these codes are not included in OSD ROM area).
Fig. 8.10.18 Structure of OSD RAM
Rev. 1.0
68
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(4) Character color
(6) OUT1, OUT2 signals
Character colors are specified by RA1 to RA3 of OSD RAM.
Color data are set by color register i (CO1 to CO8: addresses 00E616
to 00E916, 00EC16 to 00EF16) in advance, and 8 kinds of color register i are specified by color codes.
OUT1 signal is used to erase a back ground TV image. The output
waveform of OUT1 signal is controlled by combining the following
bits; the display mode selection bits (bits 0 to 2 of the block i control
register), the border type selection bit (bit 1 of the OSD control register), and the OUT1 output control bit (bit 6 of color register i).
Figure 8.10.20 and 8.10.21 shows the output example of R, G, B,
and OUT1.
OUT2 signal is used to change the luminance of a background TV
image. The output waveform of OUT2 signal is blank output and is
controlled per character unit by RA6 of OSD RAM.
(5) Character background color
Character background are specified by color register i as same as
character color.
Note : The character background is displayed in the following part:
(character display area) – (character font) — (border) – (BUTTON display area)
Accordingly, the character background color and the color signal for
these sections cannot be mixed.
Color Register i
b7 b6 b5 b4 b3 b2 b1 b0
Color register i (CO1 to CO8) (i=1 to 8) [Addresses 00E616 to 00E916, 00EC16 to 00EF16]
B
Name
@
Functions
After re set
R W
0
R signal output selection
bit (COi0)
0: No output
1: Output
Indeterminate R W
1
G signal output selection
bit (COi1)
0: No output
1: Output
Indeterminate R W
2
B signal output selection
bit (COi2)
0: No output
1: Output
Indeterminate R W
3
R signal output (background) 0: No output
selection bit (COi3)
1: Output
Indeterminate R W
4
G signal output (background) 0: No output
selection bit (COi4)
1: Output
Indeterminate R W
5
B signal output (background) 0: No output
1: Output
selection bit (COi5)
Indeterminate R W
6
OUT1 output control bit
(COi6)
Indeterminate R W
7
Nothing is assined. This bit is a write disable bit.
When this bit is read out, the value is “0.”
0: Character output
1: Blank output
0
R —
Fig. 8.10.19 Color register i (i = 1 to 8)
Rev. 1.0
69
70
0
0
0
0
b2
1
1
1
1
b1
0
0
0
0
b0
= FONT
= FONT
= FONT
= FONT
G output
= AREA— FONT
— BORDER
No
output
= “L” (See note 1)
= AREA — FONT
No
output
= “L” (See note 1)
B output
(background output)
BORDER = border pattern output around FONT
BUTTON = buttun display output around AREA
Notes 1: when positive polarity is selected.
2: Examples of all bordered display are shown.
= WHITE (= R + G + B)
= BLACK ( = OUT1)
AREA = character display area in OSD mode
0
0
0
0
b3
= BLUE (= B)
0
0
0
0
b4
FONT= font pattern output
1
0
0
1
1
0
0
1
b5
b6
OSD color register i
= GREEN (= G)
OS D
(Bordered)
OS D
(Not bordered)
Display
mode
Display example
BUTTON mode character
display area
OSD mode character display
area (AREA)
=AREA
= FONT + BORDER
= AREA
= FONT
OUT1 output
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Fig. 8.10.20 Output Example of R, G, B and OUT1 (Character Color: Green, Character Background Color: Blue) (In OSD Mode)
Rev. 1.0
0
0
0
0
b2
1
1
1
1
b1
0
0
0
0
b0
= FONT
+ BUTTON
= FONT
+ BUTTON
= FONT
+ BUTTON
= FONT
+ BUTTON
G output
BORDER = border pattern output around FONT
BUTTON = buttun display output around AREA
Notes 1: when positive polarity is selected.
2: Examples of all bordered display are shown.
3: Examples of BUTTON display by RA4 and RA5 of OSD RAM are shown.
= WHITE (= R + G + B)
= BLACK ( = OUT1)
= AREA + BUTTON
– FONT –BORDER
= BUTTON
= AREA +
BUTTON – FONT
= BUTTON
B output
(background output)
AREA = character display area in OSD mode
0
0
0
0
b3
FONT= font pattern output
0
0
0
0
b4
= GREEN (= G)
1
0
0
1
1
0
0
1
b5
b6
OSD color register i
= BLUE (= B)
OS D
(Bordered)
OS D
(Not bordered)
Display
mode
Display example
BUTTON mode character
display area
OSD mode character display
area (AREA)
= AREA + BUTTON
= FONT + BORDER
+ BUTTON
= AREA + BUTTON
= FONT + BUTTON
OUT1 output
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Fig. 8.10.21 Output Example of R, G, B and OUT1 (Character Color: Green, Character Background Color: Blue) (In BUTTON Mode)
Rev. 1.0
71
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(7) Attribute (block display)
The attributes (border, BUTTON display, block shadow display) are
controlled to the character font. The display mode is specified per
block unit by bits 0 to 2 of the block i control register. The attributes to
be controlled are different depending on each mode.
OSD mode .............. Border
BUTTON mode ....... Border, BUTTON display, block shadow display
➀ Border
The border is output in the OSD and BUTTON modes. The all
bordered (bordering around of character font) and the shadow
bordered (bordering right and bottom sides of character font) are
selected per screen unit by bit 1 of OSD control register (refer to
Figure 8.10.4). The ON/OFF switch for borders can be controlled
per block unit by bit 2 of the block i control register (refer to Figure 8.10.8).
The OUT1 signal is used for border output.
The horizontal size (x) of border is 1TOSC (TOSC: OSD oscillation
cycle) regardless of the character font dot size. The vertical size
(y) is 1H (2H in the bi-scan mode) regardless of character font.
Notes 1: The border dot area is the shaded area as shown in Figure 8.10.23.
2: When the border dot overlaps on the next character font, the character font has priority (refer to Figure 8.10.22 A). When the border dot
overlaps on the next character back ground, the border has priority
(refer to Figure 8.10.22 B).
3: The border in vertical out of character area is not displayed in OSD
mode (refer to Figure 8.10.22).
Character boundary
B
Character boundary Character boundary
A
B
Priority level:
BUTTON display = block shadow display > FONT display > border display > character background display
Fig. 8.10.22 Border Priority
Rev. 1.0
72
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
All border
Border display area
1 6 d o ts
Width of border dot ( = 1H)
(See note)
2 0 d o ts
Character
font area
Width of border dot ( = 1H)
(See note)
Shadow border
Border dot
( =1TOSC)
Border dot
( =1TOSC)
Note: It is possible in only BUTTON mode.
FONT
BORDER
This is display example when 1TOSC ✕ 1H of dot size.
Fig. 8.10.23 Border Display Example and Border Area
Rev. 1.0
73
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
➁ BUTTON display
There are 2 kinds of displays; ON BUTTON display and OFF
BUTTON display. The BUTTON display is controlled per character unit by RA4 and RA5 of OSD RAM.
The BUTTON display area is around the character display area
in the BUTTON mode. The ON/OFF BUTTON is displayed by
outputting white (R + G + B) or black (OUT) to this area.
The horizontal size (x) of BUTTON display area is for 2 dots regardless of the character font dot size. The vertical size (y) is for
2 dots regardless of the vertical dot size of character font.
➂ Block shadow display
The block shadow is displayed to the character display area in
the BUTTON mode. The block shadow display is controlled per
character unit by RA4 and RA5 of OSD RAM.
FIgure 8.10.24 shows each display example. The BUTTON/block
shadow can be displayed to the character area where combined arbitrary (within 24 characters for a block). Set each character in this
case, too. Set “0” to all attribute codes between ON BUTTON, OFF
BUTTON and block shadow displays.
BUTTON display area
(= 2 dots)
16 dots
Shadow display area
( = 2 dots)
16 dots
22 dots
20 dots
ON BUTTON
OFF BUTTON
BUTTON display area
(= 2 dots)
Shadow display area
( = 2 dots)
= Character font display area
Fig. 8.10.24 ON/OFF BUTTON Display and Block Shadow Display
Rev. 1.0
74
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Attribute code
Attribute code
RA5
RA4
0
0
0
1
0
1
0
0
1
0
1
0
1
0
(See notes 2, 3)
0
0
1
1
(See note 1)
• • •
Notes 1: When RA4 = RA5 = “1,” shadow border can be displayed in
character display area.
2: When RA4 = RA5 = “0,” character background color can be
colored in all display area.
3: 3 kinds of display (ON button, OFF button and block shadow)
can be displayed within the same block. Be sure to set attributes
between these display to “0.”
= Character display area in OSD mode
Fig. 8.10.25 Attribute Codes and Display Examples
Rev. 1.0
75
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(8) Multiline display
This microcomputer can ordinarily display 2 lines on the CRT screen
by displaying 2 blocks at different vertical positions. In addition, it can
display 3 lines or more by using OSD interrupts.
An OSD interrupt request occurs at the point at which display of each
block has been completed. In other words, when a scanning line
reaches the point of the display position (specified by the block i V
registers) of a certain block, the character display of that block starts,
and an interrupt occurs at the point at which the scanning line exceeds the block.
Notes 1: An OSD interrupt does not occur at the end of display when the block
is not displayed. In other words, if a block is set to off display by the
display control bit of the block control register i (addresses 00F916
and 00FA16), an OSD interrupt request does not occur (refer to Figure 8.10.26 (A)).
2: When another block display appeares while one block is displayed,
an OSD interrupt request occurs only once at the end of the another
block display (refer to Figure 8.10.26 (B)).
3: On the screen setting window, an OSD interrupt occurs even at the
end of the block (off display) out of window (refer to Figure 12.11.36
(C)).
Block 1 (on display)
“OSD interrupt request”
Block 1 (on display)
“OSD interrupt request”
Block 2 (on display)
“OSD interrupt request”
Block 2 (on display)
“OSD interrupt request”
Block 1' (off display)
No
“OSD interrupt request”
Block 2' (off display)
No
“OSD interrupt request”
Block 1' (on display)
Block 2' (on display)
“OSD interrupt request”
“OSD interrupt request”
On display (OSD interrupt request occurs
at the end of block display)
Off display (OSD interrupt request does
not occur at the end of block display)
(A)
Block 1
“OSD interrupt request”
Block 1
Block 2
No
“OSD interrupt request”
Block 2
“OSD interrupt request”
“OSD interrupt request”
Block 1'
“OSD interrupt request”
Window
(B)
(C)
Fig. 8.10.26 Note on Occurence of OSD Interrupt
Rev. 1.0
76
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(9) Window function
The window function can be set windows on-screen, and output OSD
within only the area where the window is set.
The ON/OFF for vertical window function is performed by bit 4 of the
OSD control register. The top boundary is set by the top border control register (TBR) and the bottom boundary is set by bottom border
control register (BBR). The left boundary is set by the left border
control register (LBR), and the right boundary is set by the right border control register (RBR).
The left and right boundarys can be adjusted minutely by bits 2 and 3
of the OSD control register (address 00EA16).
Note: The SPRITE display is not effected by the window function.
HSYNC
Tdef4 4TOSC ✕ LBR + 1TOSC ✕ WH
4TOSC ✕ RBR + 1TOSC ✕ WH
VSYNC
Left boundary
of window
Right boundary
of window
Window
Hdef
Top boundary
of window
TBR
F
BBR
G H
K L
P
I
J
M N O
Window
Q R S T
Bottom boundary
of window
Screen
LBR
RBR
WH
TOSC
Tdef4
TBR
BBR
Hdef
H
: Value of left border control register
: Value of right border control register
: Value (0 to 3) of window horizontal position minute adjustment bit
: OSD oscillation cycle
: 4TOSC
: Value of top border control register
: Value of bottom border control register
: 17H
: HSYNC
Fig. 8.10.27 Example of window function
Rev. 1.0
77
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Top Border Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Top border control register (TBR) [Address 024516]
B
Name
Functions
0 Control bits of
Top border position = Hdef + H ✕ n
to top border
(n: setting value, Hdef: 17H, H: HSYNC)
7 (TBR0 to TBR7)
After reset R W
Indeterminate R W
Notes 1: Set values except “0016” to TBR.
2: Set values fit for TBR ≤ BBR.
Fig. 8.10.28 Top Border Control Register
Bottom Border Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Bottom border control register (BBR) [Address 024616]
B
Name
Functions
0 Control bits of
Bottom border position = Hdef + H ✕ n
to bottom border
(n: setting value, Hdef: 17H, H: HSYNC)
7 (BBR0 to BBR7)
After reset R W
Indeterminate R W
Notes 1: Set values except “0016” to BBR.
2: Set values fit for TBR ≤ BBR.
Fig. 8.10.29 Bottom Border Control Register
Rev. 1.0
78
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Left Border Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Left border control register (LBR) [Address 024016]
B
Name
0
to
6
Control bits of
left border
(LBR0 to LBR6)
Functions
7
Nothing is assigned. This bit is write disable bit.
When this bit is read out, the value is indeterminate.
After re set R W
Left border position = Tdef4 + 4TOSC ✕ n + 1TOSC ✕ WH
(n: setting value, Tde f4: 4TOSC,
TOSC: OSD oscillation cycle,
0
R
W
0
R
—
WH: value (0 to 3) of window horizontal position minute adjustment bit)
Note: Set values fit for LBR ≤ RBR.
Fig. 8.10.30 Left BorderControl Register
Right Border Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Right border control register (RBR) [Address 024116]
B
Name
0
to
6
Control bits of
left border
(RBR0 to RBR6)
Functions
7
Nothing is assigned. This bit is write disable bit.
When this bit is read out, the value is indeterminate.
Right border position = Tdef4 + 4TOSC ✕ n + 1TOSC ✕WH
(n: setting value, Tde f4: 4TOSC,
TOSC: OSD oscillation cycle,
After re set R W
0
R
W
0
R
—
WH: value (0 to 3) of window horizontal position minute adjustment bit)
Note: Set values fit for LBR ≤ RBR.
Fig. 8.10.31 Right Border Control Register
Rev. 1.0
79
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.2 SPRITE Display
To display SPRITE font, OSD ROM font data for 2 characters is used.
These 2 fonts can be colored with any color and can be displayed by
synthesizing as a character. The features and display example of
SPRITE display are shown below.
This is especially suitable for cursor and other displays as its function allows for display in any position, regardless of the validity of
other OSDs or display positions. Each SPRITE font is ROM font consisting of 16 horizontal dots ✕ 20 vertical dots, and there are 4 kinds.
When SPRITE display overlaps with other OSDs, SPRITE display is
always given priority.
Notes 1: The SPRITE display is not effected by the window function.
2: The SPRITE display cannot output character background color or
OUT2.
Table 8.10.4 Features of SPRITE Display
Parameter
Features
Number of display characters
1 characters ✕ 1 line (display by synthesizing 2 kinds of characters)
16 ✕ 20 dots (See note 3)
Dot structure
Kinds of characters
4 kinds (Character code = “F816” to “FF16”) (See note 4)
1 kind
Kinds of character sizes
Dot size
1TOSC ✕ 1H (See notes 5, 7, 8)
Character font coloring
Synthesis SPRITE fonts 1 and 2 (per SPRITE font unit)
OSD output
R, G, B
Other functions
Corresponding to bi-scan
Display position
Horizontal: 253 levels (See note 2), Vertical: 255 levels (See note 1)
Notes 1: It is possible to set in any position regardless of vertical display positions of the block display. The vertical display start positions of the SPRITE
display is the same as that of the block display.
2: It is possible to set in any position regardless of horizontal display position of block display.
3: It is the same display area as OSD mode (refer to “Figure 8.10.3”).
4: As for character font data storing address refer to “8.10.1 Block Display (3) Memory for OSD.” The characters of character codes “F816” to
“FF16” can be also used for the block display.
5: Refer to “8.10.1 Block Display (2) Dot size.” The dot size in the bi-scan mode is 1TOSC ✕ 2H.
6: Refer to “8.10.1 Block Display (4) Character color.” Only color registers 1 to 4 can be specified.
7: H = HSYNC
8: TOSC = OSD oscillation cycle
USER SELECT
BRIGHTNESS
TINT
SOUND MONAURAL
STEREO
SPRITE font 1
SPRITE display
Note: SPRITE fonts 1 and 2 are displayed by synthesizing.
SPRITE font 2
Fig. 8.10.32 SPRITE Display Example
Rev. 1.0
80
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
SPRITE H Register
b7 b6 b5 b4 b3 b2 b1 b0
SPRITE H register (SHP) [Address 00E416]
B
Name
Functions
0 Horizontal display Horizontal display start position
to start position
= Tdef2 + 2TOSC ✕ n
7 control bits of
(n: setting value, Tdef2: 2TOSC,
TOSC: OSD oscillation cycle)
SPRITE OSD
(SHP0 to SHP7)
After reset R W
0
R W
Notes 1: Set values except “0016” to “0216” to SHP.
2: When selecting raster patterning display, setting value is
synchronized with VSYNC signal; when selecting SPRITE
display, it is not synchronized.
Fig. 8.10.33 SPRITE H Register
When setting the SPRITE H register to “0316,” the interval of Tdef2 + 2TOSC ✕ 3 = 8TOSC is necessary
from a rising edge (negative polarity) to horizontal display start position.
HSYNC
Tdef2
2TOSC ✕ NH'
NH' : value of SPRITE H register (decimal) (see note)
TOSC : OSD oscillation cycle
Tdef2 : 2TOSC
Note: Do not set “0” to “2” to NH'.
Fig. 8.10.34 Note on Horizontal Display Start Position of SPRITE Display
SPRITE V Register
b7 b6 b5 b4 b3 b2 b1 b0
SPRITE V register (SVP) [Address 00E516]
B
Name
Functions
After reset R W
0 Horizontal display Horizontal display start position Indeterminate R W
to start position
= Hdef + H ✕ n
7 control bits of
(n: setting value, Hdef: 17H, H: HSYNC)
SPRITE OSD
(SVP0 to SVP7)
(See note 1)
Note: Set values except “0016” to the SVP.
Fig. 8.10.35 SPRITE V Register
Rev. 1.0
81
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
SPRITE Control Register
b7 b6 b5 b4 b3 b2 b1 b0
SPRITE control register (SC) [Address 00E316]
B
Name
Functions
After reset R W
0, 1 SPRITE font 1
color register
specification bit
(SC0, SC1)
SC1
0
0
1
1
@SC0
0: Color
1: Color
0: Color
1: Color
register 1
register 2
register 3
register 4
2, 3 SPRITE font 2
color register
specification bit
(SC2, SC3)
SC3
0
0
1
1
@SC2
0: Color
1: Color
0: Color
1: Color
register 1
register 2
register 3
register 4
4, 5 SPRITE font selection bit
(SC4, SC5)
SC5 SC4 Character code
SPRITE1 SPRITE2
0
0
1
1
6, 7 SPRITE/raster patterning
control bit
(SC6, SC7)
(See note)
SC7
0
0
1
1
0
1
0
1
F816
FA16
FC16
FE16
0
R W
0
R W
0
R W
0
R W
F916
FB16
FD16
FF16
@SC6
0: Display OFF
1: Do not set
0: SPRITE display
1: Raster patterning
display
Note : This bit is valid when bit 0 of the OSD control register to “1.”
Fig. 8.10.35 SPRITE Control Register
Rev. 1.0
82
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.3 Raster Display
The raster display is displayed on the lower layer than the SPRITE
and block layers. There are 2 kinds of displays; the flat display and
the patterning display.
In the raster flat display, an entire screen (raster) can be colored by
setting the following bits; bits 5 to 7 of the OSD I/O polarity register
and bits 6 and 7 of the OSD control register. Since each of the R, G,
B, OUT1, and OUT2 pins can be switched to raster coloring output, 8
raster colors can be obtained.
In the raster patterning display, SPRITE fonts are displayed repeatedly on an entire screen (raster). At this time, set “1” to bits 6 and 7 of
the SPRITE control register.
Horizontal display start positions of the raster patterning display are
set by the SPRITE H register. At this time, setting value is synchronized with VSYNC signal.
Characters for patterning are set by bits 4 and 5 of the SPRITE control register and coloring are set by bits 0 to 3. The raster color is
output on the background of SPRITE font.
Note that the raster patterning display and the SPRITE display cannot be used at the same time.
When the character color/the character background color overlaps
with the raster color, the color (R, G, B, OUT1, OUT2), specified for
the character color/the character background color, takes priority of
the raster color. This ensures that the character color/the character
background color is not mixed with the raster color.
The raster flat display example is shown in Figure 8.10.36, the raster
patterning display example is shown in Figure 8.10.37.
: Character color “RED” (R + OUT1 + OUT2)
: Border color “BLACK” (OUT1 + OUT2)
: Background color “MAGENTA” (R + B + OUT1 + OUT2)
: Raster color “BLUE” (R + OUT1 + OUT2)
A
A'
HSYNC
OUT1
OUT2
R
Signals
across
A-A'
G
B
Fig. 8.10.36 Raster Flat Display Example
Rev. 1.0
83
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
When setting “0316” to SPRITE H register, it is need Tdef2 + 2TOSC ✕ 3
= 8TOSC intervals from a rising edge (negative polarity) of HSYNC signal
to a horizontal display start position.
SPRITE font
Raster color “BLUE” (B + OUT1)
SPRITE font 1 color “BLACK” (OUT1)
SPRITE font 2 color “WHITE” (R + G + B + OUT1)
H S YN C
Tdef2 2TO S C ~N H ’
(See note)
screen
NH' : Value of SPRITE H register (decimal) (See note)
TOSC : OSD oscillation cycle
Tdef2 : 2TOSC
Note: Do not set “0” to “2” to NH'.
Fig. 8.10.37 Raster Patterning Display Example
Rev. 1.0
84
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.11 SOFTWARE RUNAWAY DETECT FUNCTION
This microcomputer has a function to decode undefined instructions
to detect a software runaway.
When an undefined op-code is input to the CPU as an instruction
code during operation, the following processing is done.
➀ The CPU generates an undefined instruction decoding signal.
➁ The device is internally reset because of occurrence of the undefined instruction decoding signal.
➂ As a result of internal reset, the same reset processing as in the
case of ordinary reset operation is done, and the program restarts
from the reset vector.
Note, however, that the software runaway detecting function cannot
be invalid.
φ
SYNC
Address
Data
PC
01,S
?
?
01,S–1
PCH
PCL
01,S–2
PS
ADH,
ADL
FFFF16
FFFE16
ADL
ADH
Reset sequence
Undefined instruction decoding signal
occurs.Internal reset signal occurs.
: Undefined instruction decode
?
: Invalid
PC : Program counter
S : Stack pointer
ADL, ADH : Jump destination address of reset
Fig.8.11.1 Sequence at Detecting Software Runaway Detection
Rev. 1.0
85
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.12. RESET CIRCUIT
Poweron
When the oscillation of a quartz-crystal oscillator or a ceramic resonator is stable and the power source voltage is 5 V ± 10 %, hold the
RESET pin at LOW for 2 µs or more, then return is to HIGH. Then, as
shown in Figure 8.12.2, reset is released and the program starts form
the address formed by using the content of address FFFF 16 as the
high-order address and the content of the address FFFE16 as the
low-order address. The internal state of microcomputer at reset are
shown in Figures 8.2.3 to 8.2.6.
An example of the reset circuit is shown in Figure 8.12.1.
The reset input voltage must be kept 0.9 V or less until the power
source voltage surpasses 4.5 V.
4.5 V
Power source voltage 0 V
0.9 V
Reset input voltage 0 V
Vcc
1
5
M51953AL
RESET
4
3
0.1 µF
Vss
Microcomputer
Fig.8.12.1 Example of Reset Circuit
XIN
φ
RESET
Internal RESET
SYNC
Address
?
01, S
?
01, S-1 01, S-2
FFFE
FFFF
ADH ,
ADL
Reset address from the vector table
Data
?
32768 count of X IN
clock cycle (See note 3)
?
?
?
?
ADL
ADH
Notes 1 : f(XIN) and f(φ) are in the relation : f(X IN) = 2·f (φ).
2 : A question mark (?) indicates an undefined state that
depends on the previous state.
3 : Immediately after a reset, timer 3 and timer 4 are
connected by hardware. At this time, “FF 16” is set
in timer 3 and “07 16” is set to timer 4. Timer 3 counts down
with f(XIN)/16, and reset state is released by the timer 4
overflow signal.
Fig.8.12.2 Reset Sequence
Rev. 1.0
86
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.13 CLOCK GENERATING CIRCUIT
The built-in clock generating circuit is shown in Figure 8.13.3. When
the STP instruction is executed, the internal clock φ stops at HIGH.
At the same time, timers 3 and 4 are connected by hardware and
“FF16” is set in timer 3 and “0716” is set in the timer 4. Select f(XIN)/16
as the timer 3 count source (set bit 0 of the timer mode register 2 to
“0” before the execution of the STP instruction). Moreover, set the
timer 3 and timer 4 interrupt enable bits to disabled (“0”) before execution of the STP instruction). The oscillator restarts when external
interrupt is accepted. However, the internal clock φ keeps its HIGH
until timer 4 overflows, allowing time for oscillation stabilization when
a ceramic resonator or a quartz-crystal oscillator is used.
When the WIT instruction is executed, the internal clock φ stops in
the HIGH but the oscillator continues running. This wait state is released when an interrupt is accepted (See note). Since the oscillator
does not stop, the next instruction can be executed at once.
When returning from the stop or the wait state, to accept an interrupt,
set the corresponding interrupt enable bit to “1” before executing the
STP or the WIT instructions.
Microcomputer
XIN
XOUT
CIN
COUT
Fig.8.13.1 Ceramic Resonator Circuit Example
Microcomputer
Note: In the wait mode, the following interrupts are invalid.
• VSYNC interrupt
• OSD interrupt
• Timer 2 interrupt using external clock input from TIM2 pin as count
source
• Timer 3 interrupt using external clock input from TIM3 pin as count
source
• Timer 4 interrupt using f(XIN)/2 as count source
• Timer 1 interrupt using f(XIN)/4096 as count source
• f(XIN)/4096 interrupt
• Multi-master I2C-BUS interface interrupt
• A-D conversion interrupt
• SPRITE interrupt
X IN
Vcc
External oscillation circuit
Vss
Fig.8.13.2 External Clock Input Circuit Example
A circuit example using a ceramic resonator (or a quartz-crystal oscillator) is shown in Figure 8.13.1. Use the circuit constants in accordance with the resonator manufacture’s recommended values. A circuit example with external clock input is shown in Figure 8.13.2. Input the clock to the XIN pin, and open the XOUT pin.
Interrupt request
S
Interrupt disable
flag I
S
Q
Q
Reset
S
Q
Reset
STP instruction
Selection gate :
Connected to black
side at reset.
WIT
instruction
R
R
R
TM2 : Timer mode register 2
STP
instruction
Internal clock φ
1/2
1/8
Timer 3
Timer 4
TM20
TM22
XIN
XOUT
Fig.8.13.3 Clock Generating Circuit Block Diagram
Rev. 1.0
87
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.14 DISPLAY OSCILLATION CIRCUIT
8.16 ADDRESSING MODE
The OSD oscillation circuit has a built-in clock oscillation circuits, so
that a clock for OSD can be obtained simply by connecting an LC, a
ceramic resonator, or a quartz-crystal oscillator across the pins OSC1
and OSC2. Which of the sub-clock or the OSD oscillation circuit is
selected by setting bits 0 and 1 of the interrupt input polarity register
(address 00CD16).
The memory access is reinforced with 17 kinds of addressing modes.
Refer to SERIES 740 <Software> User’s Manual for details.
8.17 MACHINE INSTRUCTIONS
There are 71 machine instructions. Refer to SERIES 740 <Soft- ware>
User’s Manual for details.
9. PROGRAMMING NOTES
OSC1
• The divide ratio of the timer is 1/(n+1).
• Even though the BBC and BBS instructions are executed immediately after the interrupt request bits are modified (by the program), those instructions are only valid for the contents before
the modification. At least one instruction cycle is needed (such as
an NOP) between the modification of the interrupt request bits
and the execution of the BBC and BBS instructions.
• After the ADC and SBC instructions are executed (in the decimal
mode), one instruction cycle (such as an NOP) is needed before
the SEC, CLC, or CLD instruction is executed.
• An NOP instruction is needed immediately after the execution of
a PLP instruction.
• In order to avoid noise and latch-up, connect a bypass capacitor
(≈ 0.1µF) directly between the VCC pin–VSS pin, AVCC pin–VSS
pin, and the VCC pin–CNVSS pin, using a thick wire.
OSC2
L
C1
C2
Fig.8.14.1 Display Oscillation Circuit
8.15 AUTO-CLEAR CIRCUIT
When a power source is supplied, the auto-clear function will operate by connecting the following circuit to the RESET pin.
Circuit example 1
Vcc
RESET
Vss
Circuit example 2
RESET
Vcc
Vss
Note : Make the level change from “L” to “H” at the point at
which the power source voltage exceeds the specified
voltage.
Fig.8.15.1 Auto-clear Circuit Example
Rev. 1.0
88
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
10. ABSOLUTE MAXIMUM RATINGS
Symbol
VCC, AVCC
VI
VI
VO
VO
IOH
IOL1
IOL2
IOL3
IOL4
Pd
Topr
Tstg
Parametear
Power source voltage VCC
Input voltage
CNVSS
Input voltage
P00–P07, P10–P17, P20–P27,
P30–P35, OSC1, XIN, P50, P51,
______
RESET
Output voltage
P06, P07, P10–P17, P20–P27,
P30–P32, P35, P52–P55,
XOUT, OSC2
Output voltage
P00–P05
Circuit current
P52–P55, P10–P17,
P20–P27, P30, P31, P35
Circuit current
P52–P55, P06, P07, P10, P15–P17,
P20–P23, P30–P32, P35
Circuit current
P11–P14
Circuit current
P00–P05
Circuit current
P24, P27
Power dissipation
Operating temperature
Storage temperature
Conditions
All voltages are
based on VSS.
Output transistors
are cut off.
Ta = 25 °C
Ratings
–0.3 to 6
–0.3 to 6
–0.3 to VCC + 0.3
Unit
V
V
V
–0.3 to VCC + 0.3
V
–0.3 to 13
0 to 1 (See note 1)
V
mA
0 to 2 (See note 2)
mA
0 to 6 (See note 2)
0 to 1 (See note 2)
0 to 10 (See note 3)
550
–10 to 70
–40 to 125
mA
mA
mA
mW
°C
°C
11. RECOMMENDED OPERATING CONDITIONS (Ta = –10 °C to 70 °C, VCC = 5 V ± 10 %, unless otherwise noted)
Symbol
VCC
VSS
VIH1
VIH2
VIL1
VIL2
VIL3
IOH
IOL1
IOL2
IOL3
IOL4
f(XIN)
fosc
fhs1
fhs2
fhs3
Parameter
Power source voltage (See note 4), During CPU, OSD, data slicer operation
Power source voltage
HIGH input voltage
P00–P07, P10–P17, P20–P27, P30–P35,
SIN, SCLK, P50, P51, RESET, XIN, OSC1,
TIM2, TIM3, INT1–INT3
HIGH input voltage
SCL1, SCL2, SDA1, SDA2
LOW input voltage
P00–P07, P10–P17, P20–P27, P30–P35
LOW input voltage
SCL1, SCL2, SDA1, SDA2
LOW input voltage (See note 6)
P50, P51, RESET, TIM2, TIM3, INT1–INT3,
XIN, OSC1, SIN, SCLK
HIGH average output current (See note 1)
P52–P55, P10–P17, P20–P27,
P30, P31, P35
LOW average output current (See note 2)
P52–P55, P06, P07, P10,
P15–P17, P30–P32, P35
LOW average output current (See note 2)
P11–P14
LOW average output current (See note 2)
P00–P05
LOW average output current (See note 3)
P24–P27
Oscillation frequency (for CPU operation) (See note 5) XIN
RC oscillating mode
Oscillation frequency (for OSD)
OSC1
LC oscillating mode
Ceramic oscillating mode
Input frequency
Input frequency
Input frequency
TIM2, TIM3
SCLK
SCL1, SCL2
Limits
Min.
4.5
0
0.8VCC
Typ.
5.0
0
0.7VCC
0
0
0
7.9
5.0
5.0
7.9
Max.
5.5
0
VCC
VCC
0.4 VCC
0.3 VCC
0.2 VCC
8.0
8.0
8.0
8.0
Unit
V
V
V
V
V
V
V
1
mA
2
mA
6
1
10
8.1
9.0
17.0
8.1
100
1
400
mA
mA
mA
MHz
MHz
kHz
MHz
MHz
Rev. 1.0
89
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
12. ELECTRIC CHARACTERISTICS (VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = –10 °C to 70 °C, unless otherwise noted)
Symbol
ICC
VOH
VOL
Parameter
Power source current
Test conditions
System operation
Stop mode
HIGH output voltage P52–P55, P10–P17,
P20–P27,P30, P31, P35
LOW output voltage P52–P55, P00–P07, P10,
P15–P17, P20–P23, P30–P32,
P35
LOW output voltage P24–P27
OSD OFF
OSD ON
VCC = 5.5 V, f(XIN) = 0
VCC = 4.5 V
IOH = –0.5 mA
VCC = 4.5 V
IOL = 0.5 mA
Min.
VCC = 5.5 V,
f(XIN) = 8 MHz
VCC = 4.5 V
IOL = 10.0 mA
LOW output voltage P11–P14
VCC = 4.5 V IOL = 3 mA
IOL = 6 mA
____________
VT+ – VT– Hysteresis (See note 6) RESET, P50, P51, TIM2, TIM3, VCC = 5.0 V
INT1–INT3, SCL1, SCL2,
SDA1, SDA2, SIN, SCLK
____________
HIGH input leak current RESET, P00–P07, P10–P17,
VCC = 5.5 V
IIZH
P20–P27, P30–P35, P50, P51
VI = 5.5 V
____________
LOW input leak current RESET, P00–P07, P10–P17,
VCC = 5.5 V
IIZL
P20–P27, P30–P35, P50, P51
VI = 0 V
HIGH input leak current P00–P05
VCC = 5.5 V
IOZH
VI = 12 V
I2C-BUS·BUS switch connection resistor
VCC = 4.5 V
RBS
(between SCL1 and SCL2, SDA1 and SDA2)
Limits
Typ. Max.
20
40
30
60
300
2.4
0.4
Unit
mA
1
mA
V
V
2
3.0
0.5
Test
circuit
0.4
0.6
1.3
V
5
µA
5
µA
10
µA
5
130
Ω
6
3
4
Notes 1: The total current that flows out of the IC must be 20 mA or less.
2: The total input current to IC (IOL1 + IOL2 + IOL3) must be 30 mA or less.
3: The total average input current for ports P24–P27 to IC must be 20 mA or less.
4: Connect 0.1 µF or more capacitor externally between the power source pins VCC–VSS so as to reduce power source noise.
Also connect 0.1 µF or more capacitor externally between the pins VCC–CNVSS.
5: Use a quartz-crystal oscillator or a ceramic resonator for the CPU oscillation circuit. When using the data slicer, use 8 MHz.
6: P06, P07, P15, P23, P24 have the hysteresis when these pins are used as interrupt input pins or timer input pins. P1 1–P14 have the hysteresis when these
pins are used as multi-master I2C-BUS interface ports. P20–P22 have the hysteresis when these pins are used as serial I/O pins.
7: Pin names in each parameter is described as below.
(1) Dedicated pins: dedicated pin names.
(2) Duble-/triple-function ports
• When the same limits: I/O port name.
• When the limits of functins except ports are different from I/O port limits: function pin name.
Rev. 1.0
90
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
+ Power source voltage
1
2
4.5 V
A
Icc
XIN
Vcc
Vcc
8.00 MHz
OSC1
XOUT
Each output pin
OSC2
VOH
Vss
V
Vss
Pin VCC is made the operation state and is
measured the current, with a ceramic
resonator.
3
IOH
or
or
VO L
IOL
After setting each output pin to HIGH level when measuring VOH
and to LOW level when measuring VOL, each pin is measured.
5.0 V
4
5.5 V
Vcc
V cc
IIZH
or
IIZL
Each input pin
Each input pin
A
Vss
V ss
5.5 V
5
6
4.5V
12 V
Vcc
Vcc
IOZH
Each output pin
IBS
SCL1 or SDA1
A
A
RB S
SCL2 or SDA2
VBS
Vss
Vss
After setting each output pin OFF state, each
pin is measured
RBS = VBS/IBS
Fig.12.1 Measure Circuits
Rev. 1.0
91
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
13. A-D CONVERTER CHARACTERISTICS
(VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = –10 °C to 70 °C, unless otherwise noted)
Symbol
—
—
TCONV
RLADDER
VIA
Parameter
Test conditions
Resolution
Absolute accuracy (excludig guantization error)
Conversion time
Ladder resistor
Analog input voltage
Min.
Limits
Typ.
Max.
8
±2.5
12.5
Vcc = 5 V
12.25
25
0
VREF
Unit
bits
LSB
µs
kΩ
V
14. MULTI-MASTER I2C-BUS BUS LINE CHARACTERISTICS
Symbol
tBUF
Standard clock mode High-speed clock mode
Unit
Min.
Max.
Min.
Max.
4.7
1.3
µs
4.0
0.6
µs
4.7
1.3
µs
1000
20+0.1Cb
300
ns
0
0
0.9
µs
4.0
0.6
µs
300
20+0.1Cb
300
ns
250
100
ns
4.7
0.6
µs
4.0
0.6
µs
Parameter
Bus free time
Hold time for START condition
LOW period of SCL clock
Rising time of both SCL and SDA signals
Data hold time
HIGH period of SCL clock
Falling time of both SCL and SDA signals
Data set-up time
Set-up time for repeated START condition
Set-up time for STOP condition
tHD; STA
tLOW
tR
tHD; DAT
tHIGH
tF
tSU; DAT
tSU; STA
tSU; STO
Note: Cb = total capacitance of 1 bus line
SDA
tHD;STA
tBUF
tLOW
P
tR
tSU;STO
tF
Sr
S
P
SCL
tHD;STA
tHD;DAT
tHIGH
tSU;DAT
tSU;STA
S : Start condition
Sr : Restart condition
P : Stop condition
Fig.14.1 Definition Diagram of Timing on Multi-master I2C-BUS
Rev. 1.0
92
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
15. PROM PROGRAMMING METHOD
The built-in PROM of the One Time PROM version (blank) and the
built-in EPROM version can be read or programmed with a generalpurpose PROM programmer using a special programming adapter.
Product
M37225ECSP
Name of Programming Adapter
PCA7408
The PROM of the One Time PROM version (blank) is not tested or
screened in the assembly process nor any following processes. To
ensure proper operation after programming, the procedure shown in
Figure 15.1 is recommended to verify programming.
Programming with
PROM programmer
Screening (Caution)
(150°C for 40 hours)
Verification with
PROM programmer
Functional check in target device
Caution : The screening temperature is far higher
than the storage temperature. Never
expose to 150°C exceeding 100 hours.
Fig. 15.1 Programming and Testing of One Time PROM Version
Rev. 1.0
93
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
16. DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM production:
• Mask ROM Order Confirmation Form
• Mark Specification Form
• Data to be written to ROM, in EPROM form (32-pin DIP Type 27C101,
three identical copies) or FDK
Rev. 1.0
94
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
17. MASK CONFIRMATION FORM
GZZ–SH53–91B < 88A0 >
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37225M6-XXXSP
MITSUBISHI ELECTRIC
Receipt
Date:
Section head Supervisor
signature
signature
Note : Please fill in all items marked ✽.
Customer
Date
issued
Date :
Submitted by Supervisor
)
Issuance
signature
✽
TEL
(
Company
name
✽1. Confirmation
Three EPROMs are required for each pattern if this order is performed by EPROMs.
One floppy disk is required for each pattern if this order is performed by a floppy disk.
Ordering by EPROMs
If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data.
We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this
data. Thus, extreme care must be taken to verify the data in the submitted EPROMs.
Checksum code for entire EPROM
(hexadecimal notation)
EPROM type (indicate the type used)
27C101
EPROM address
0000016 Product nameASCII code:
'M37225M6-'
0000F161234567890123456
1234567890123456
1234567890123456
0A00016
Program ROM
24K bytes
0FFFF161234567890123456
1234567890123456
1140016 1234567890123456
OSD ROM 1
13BFF16 1234567890123456
15400161234567890123456
OSD ROM 2
17AFF16 1234567890123456
17B00161234567890123456
1234567890123456
1234567890123456
1FFFF161234567890123456
(1)
Set “FF16” in the shaded area.
1/3
Rev. 1.1
95
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH53–91B < 88A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37225M6-XXXSP
MITSUBISHI ELECTRIC
(2)
Write the ASCII codes that indicate the product name of “M37225M6–” to addresses 0000016 to 0000F16.
Addresses 0000016 to 0000F16 store the product name.
ASCII codes ‘M37225M6-’ are listed on the right.
The addresses and data are in hexadecimal notation.
address and data are described in hexadecimal notation.
Note: If the name of the product contained in the EPROMs does
not match the name on the mask ROM confirmation form,
the ROM processing is disabled. Please make sure the
data is written correctly.
Address
0000016
0000116
0000216
0000316
0000416
0000516
0000616
0000716
‘M ’ =
‘3’ =
‘7’ =
‘2’ =
‘2’ =
‘5’ =
‘M ’ =
‘6’ =
4 D 16
3 3 16
3 7 16
3 2 16
3 2 16
3 5 16
4 D 16
3 6 16
Address
0000816
0000916
0000A16
0000B16
0000C16
0000D16
0000E16
0000F16
‘–’ = 2 D 16
F F 16
F F 16
F F 16
F F 16
F F 16
F F 16
F F 16
✽2. Mark specification
Mark specification must be submitted using the correct form for the type of package being ordered. Fill the appropriate
mark specification form (42P4B for M37225M6-XXXSP) and attach to the mask ROM confirmation form.
(2/3)
Rev. 1.0
96
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH53–91B < 88A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37225M6-XXXSP
MITSUBISHI ELECTRIC
Inputting the character ROM
OSD ROM address of character font data
OSD ROM
address bit
AD16 AD15 AD14 AD13 AD12 AD11 AD10
Line number /
Character code /
Font bit
1
0
Ch aracter
cod e
(highorder 1)
AD9
AD8
Line number
AD7
AD6
AD5
AD4
AD3
AD2
Character code (low-order 8 bits)
AD1
AD0
Font
bit
Line number = “0A16” to “1D16”
Character code = “00016” to “17F16” (“07F16”, “08016” and “17F16 ” cannot be used.)
Font bit = 0: Left area
1: Right area
Example) The font data “60” (shaded area
) of the character code “0AA16” is stored in address
1 0 0 1 0 0 1 0 1 0 1 0 1 0 1 0 0 2 = 1255416.
Left area
Right area
Line number
DB 7 DB 6 DB 5DB 4 DB 3 DB 2 DB 1 DB 0DB 7 DB 6 DB 5 DB 4 DB 3DB 2 DB 1 DB 0
Line number 0A16
0B16
0C16
0D16
0E16
0 F1 6
1016
1116
1216
1316
1416
1516
1616
1716
1816
1916
1A16
1B16
1C16
1D16
Character code “0AA16”
Note: The 120-byte addresses corresponding to the character codes “07F16,” “08016” and “1F16” in OSD ROM are the test
data storning area. Set “FF16” to the area (We stores the test data to this area and the different data from “FF16” is
stored for the actual products.)
The test data storing area :
• addresses 1100016 + (4 + 2n) ✕ 10016 + FE16 to 1100016 + (5 + 2n) ✕ 10016 + 0116 (n = 0 to 19)
• addresses 1500016 + (4 + 2n) ✕ 10016 + FE16 and 1500016 + (4 + 2n) ✕ 10016 + FF16 n( = 0 to 19)
addresses 154FE16 and 154FF16
addresses 156FE16 and 156FF16
addresses 114FE16 to 1150116
addresses 116FE16 to 1170116
•
•
•
•
•
•
addresses 178FE16 and 178FF16
addresses 17AFE16 and 17AFF16
addresses 138FE16 to 1390116
addresses 13AFE16 to 13B0116
The 5120-byte addresses corresponding to the character codes “18016” to “1FF16” are not in OSD ROM. Set “FF16”
to the area, too.
• addresses 1500016 + (5 + 2n) ✕ 10016 + 0016 to 1500016 + (5 + 2n) ✕ 10016 + FF16 (n = 0 to 19)
addresses 1550016 to 155FF16
addresses 1570016 to 157FF16
•
•
•
addresses 1790016 to 179FF16
addresses 17B0016 to 17BFF16
3/3
Rev. 1.1
97
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH54–34B < 89A0 >
Mask ROM number
Date:
Receipt
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37225M8-XXXSP
MITSUBISHI ELECTRIC
Section head Supervisor
signature
signature
Note : Please fill in all items marked ✽.
Customer
Date
issued
Date :
Submitted by Supervisor
)
Issuance
signature
✽
TEL
(
Company
name
✽1. Confirmation
Three EPROMs are required for each pattern if this order is performed by EPROMs.
One floppy disk is required for each pattern if this order is performed by a floppy disk.
Ordering by EPROMs
If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data.
We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this
data. Thus, extreme care must be taken to verify the data in the submitted EPROMs.
Checksum code for entire EPROM
(hexadecimal notation)
EPROM type (indicate the type used)
27C101
EPROM address
0000016 Product nameASCII code:
'M37225M8-'
0000F161234567890123456
1234567890123456
0800016
Program ROM
32K bytes
0FFFF161234567890123456
1234567890123456
1140016
OSD ROM 1
13BFF16 1234567890123456
1234567890123456
15400161234567890123456
OSD
ROM 2
17AFF161234567890123456
17B00161234567890123456
1234567890123456
1234567890123456
1234567890123456
1FFFF16 1234567890123456
(1)
Set “FF16” in the shaded area.
Rev. 1.1
98
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH54–34B < 89A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37225M8-XXXSP
MITSUBISHI ELECTRIC
(2)
Write the ASCII codes that indicate the product name of “M37225M8–” to addresses 0000016 to 0000F16.
Addresses 0000016 to 0000F16 store the product name.
ASCII codes ‘M37225M8-’ are listed on the right.
The addresses and data are in hexadecimal notation.
address and data are described in hexadecimal notation.
Note: If the name of the product contained in the EPROMs does
not match the name on the mask ROM confirmation form,
the ROM processing is disabled. Please make sure the
data is written correctly.
Address
0000016
0000116
0000216
0000316
0000416
0000516
0000616
0000716
‘M ’ =
‘3’ =
‘7’ =
‘2’ =
‘2’ =
‘5’ =
‘M ’ =
‘8’ =
4 D 16
3 3 16
3 7 16
3 2 16
3 2 16
3 5 16
4 D 16
3 8 16
Address
0000816
0000916
0000A16
0000B16
0000C16
0000D16
0000E16
0000F16
‘–’ = 2 D 16
F F 16
F F 16
F F 16
F F 16
F F 16
F F 16
F F 16
✽2. Mark specification
Mark specification must be submitted using the correct form for the type of package being ordered. Fill the appropriate
mark specification form (42P4B for M37225M8-XXXSP) and attach to the mask ROM confirmation form.
(2/3)
Rev. 1.0
99
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH54–34B < 89A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37225M8-XXXSP
MITSUBISHI ELECTRIC
Inputting the character ROM
OSD ROM address of character font data
OSD ROM
address bit
AD16 AD15 AD14 AD13 AD12 AD11 AD10
Line number /
Character code /
Font bit
1
0
Ch aracter
cod e
(highorder 1)
AD9
AD8
Line number
AD7
AD6
AD5
AD4
AD3
AD2
Character code (low-order 8 bits)
AD1
AD0
Font
bit
Line number = “0A16” to “1D16”
Character code = “00016” to “17F16” (“07F16”, “08016” and “17F16 ” cannot be used.)
Font bit = 0: Left area
1: Right area
Example) The font data “60” (shaded area
) of the character code “0AA16” is stored in address
1 0 0 1 0 0 1 0 1 0 1 0 1 0 1 0 0 2 = 1255416.
Left area
Right area
Line number
DB 7 DB 6 DB 5DB 4DB 3 DB 2 DB 1 DB 0DB 7 DB 6 DB 5 DB 4 DB 3DB 2 DB 1 DB 0
Line number 0A16
0B16
0C16
0D16
0E16
0 F1 6
1016
1116
1216
1316
1416
1516
1616
1716
1816
1916
1A16
1B16
1C16
1D16
Character code “0AA16”
Note: The 120-byte addresses corresponding to the character codes “07F16,” “08016” and “1F16” in OSD ROM are the test
data storning area. Set “FF16” to the area (We stores the test data to this area and the different data from “FF16” is
stored for the actual products.)
The test data storing area :
• addresses 1100016 + (4 + 2n) ✕ 10016 + FE16 to 1100016 + (5 + 2n) ✕ 10016 + 0116 (n = 0 to 19)
• addresses 1500016 + (4 + 2n) ✕ 10016 + FE16 and 1500016 + (4 + 2n) ✕ 10016 + FF16 n( = 0 to 19)
addresses 114FE16 to 1150116
addresses 116FE16 to 1170116
addresses 154FE16 and 154FF16
addresses 156FE16 and 156FF16
•
•
•
•
•
•
addresses 138FE16 to 1390116
addresses 13AFE16 to 13B0116
addresses 178FE16 and 178FF16
addresses 17AFE16 and 17AFF16
The 5120-byte addresses corresponding to the character codes “18016” to “1FF16” are not in OSD ROM. Set “FF16”
to the area, too.
• addresses 1500016 + (5 + 2n) ✕ 10016 + 0016 to 1500016 + (5 + 2n) ✕ 10016 + FF16 (n = 0 to 19)
addresses 1550016 to 155FF16
addresses 1570016 to 157FF16
•
•
•
addresses 1790016 to 179FF16
addresses 17B0016 to 17BFF16
3/3
Rev. 1.1
100
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
18. MARK SPECIFICATION FORM
Rev. 1.0
101
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
19. ONE TIME PROM VERSION M37225ECSP MARKING
M37225ECSP
XXXXXXX
XXXXXXX is mitsubishi lot number
Rev. 1.0
102
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
20. APPENDIX
Pin Configuration (TOP VIEW)
1
42
R/P52
VSYNC/P51
P00/PWM0
P01/PWM1
P02/PWM2
P03/PWM3
P04/PWM4
P05/PWM5
P06/INT2/A-D4
P07/INT1
P23/TIM3
P24/TIM2
P25
P26
P27
DA1/P35
P32/A-D7
2
41
3
40
4
39
5
38
6
37
7
36
G/P53
B/P54
OUT1/P55
P20/SCLK
P21/SOUT(/SIN)
P22/SIN
8
9
10
11
12
13
14
M37225M6-XXXSP
M37225M8-XXXSP
M37225ECSP
HSYNC/P50
35
34
33
32
31
30
29
P10/OUT2/A-D8
P11/SCL1
P12/SCL2
P13/SDA1
P14/SDA2
P15/INT3/A-D1
P16/A-D2
P17/DA2/A-D3
P30/A-D5
15
28
16
27
17
26
CNVSS
XIN
XOUT
18
25
19
24
20
23
P31/A-D6
RESET
OSC1/P33
OSC2/P34
VSS
21
22
VC C
Outline 42P4B
Rev. 1.0
103
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Memory Map
¡M37255M6-XXXSP, M37255M8-XXXSP
000016
1000016
Zero page
SFR area
OSD ROM
(15K bytes)
00FF16
010016
01FF16
021716
021D16
(1024 bytes)
13BFF16
Not used
1540016
Not used
154FF16
2 page register (1)
1560016
Not used
Not used
156FF16
024016
Not used
2 page register (2)
024F16
Not used
1140016
00BF16
00C016
1580016
Not used
158FF16
02C016
Not used
ROM correction function
Vector 1: address 02C016
02E016
Vector 2: address 02E016
030016
15A0016
15AFF16
Not used
Vector 3: address 030016
15C0016
15CFF16
Not used
15E0016
04FF16
OSD RAM
(96 byres)
(See note)
Not used
15EFF16
080016
Not used
1600016
087716
160FF16
Not used
1620016
162FF16
Not used
1640016
164FF16
Not used
1660016
166FF16
Not used
1680016
168FF16
Not used
16A0016
16AFF16
Not used
16C0016
16CFF16
Not used
16E0016
Not used
16EFF16
Not used
1700016
170FF16
Not used
1720016
172FF16
Not used
1740016
174FF16
Not used
1760016
176FF16
Not used
1780016
178FF16
Not used
17A0016
17AFF16
M37225M8XXXSP
ROM
(32K bytes)
M37225M6XXXSP
ROM
(24K bytes)
800016
A00016
Not used
FF0016
FFDE16
FFFF16
Interrupt vector area
Special page
Note: Refer to Table 8.10.3 OSD RAM.
1FFFF16
Rev. 1.0
104
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
¡M37255ECSP
000016
1000016
Not used
1140016
00BF16
00C016
Zero page
SFR area
OSD ROM
(15K bytes)
00FF16
010016
01FF16
RAM
(2048 bytes)
021716
021D16
13BFF16
Not used
1540016
Not used
154FF16
2 page register (1)
1560016
Not used
156FF16
Not used
024016
Not used
2 page register (2)
024F16
1580016
Not used
158FF16
02C016
Not used
ROM correction function
02E016
030016
Vector 1: address 02C016
15A0016
Vector 2: address 02E016
15AFF16
Not used
Vector 3: address 030016
15C0016
15CFF16
Not used
OSD RAM
(96 bytes)
(See note)
15E0016
07FF16
080016
15EFF16
Not used
087716
1600016
Not used
090016
160FF16
Not used
09FF16
1620016
162FF16
Not used
1640016
164FF16
Not used
1660016
166FF16
Not used
1680016
168FF16
Not used
16A0016
16AFF16
Not used
16C0016
16CFF16
Not used
Not used
16E0016
16EFF16
Not used
1700016
170FF16
Not used
1720016
172FF16
Not used
1740016
174FF16
Not used
1760016
176FF16
Not used
1780016
178FF16
Not used
17A0016
17AFF16
400016
Not used
ROM
(48K byte)
Note: Refer to Table 8.10.13 OSD RAM.
FF0016
FFDE16
FFFF16
Interrupt vector area
Special page
1FFFF16
Rev. 1.0
105
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Memory Map of Special Function
Register (SFR)
■ SFR area (addresses C016 to DF16)
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
C016
C116
C216
C316
C416
C516
C616
C716
C816
C916
CA16
CB16
CC16
CD16
CE16
CF16
D016
D116
D216
D316
D416
D516
D616
D716
D816
D916
DA16
DB16
DC16
DD16
DE16
DF16
Register
Bit allocation
State immediately after reset
b0 b7
b7
b0
Port P0 (P0)
Port P0 direction register (D0)
Port P1 (P1)
Port P1 direction register (D1)
Port P2 (P2)
Port P2 direction register (D2)
Port P3 (P3)
Port P3 direction register (D3)
Port P35 output mode control register (P3S)
Port P5 (P5)
OSD port control register (PF)
P35 P34IN P33IN P32
P31S P30S P35D
0
0
0
P35S
P55 P54
OUT OUT
OUT2 P55 P54
SEL SEL SEL
Test register
Interrupt input polarity register (IP)
P53
OUT
P53
SEL
1
0
0
P31 P30
P32D P31D P30D
POL3 POL2 POL1
P52 P51
OUT IN
P52
SEL 0
1
0
P50
IN
0
0
0
0
0
0
0
0
?
0
0
0
0
0
?
0
0
0
0
OCG1OCG0
DA1-H register (DA1-H)
DA1-L register (DA1-L)
PWM0 register (PWM0)
PWM1 register (PWM1)
PWM2 register (PWM2)
PWM3 register (PWM3)
PWM4 register (PWM4)
PWM output control register 1 (PW)
PW7 PW6 PW5 PW4 PW3 PW2 PW1 PW0
PWM output control register 2 (PN)
0
0
I2C data shift register (S0)
D7
D6
I2C address register (S0D)
I2C status register (S1)
I2C control register (S1D)
I2C clock control register (S2)
Serial I/O mode register (SM)
P N5 P N4 P N3 P N2
D5
D4
D3
D2
0
0
D1
D0
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
MST TRX BB
PIN
AL AAS AD0 LRB
BSEL1 BSEL0 10BIT ALS ESO BC2 BC1 BC0
SAD
ST
ACK ABCITK MFA
ODE CCR4 CCR3 CCR2 CCR1 CCR0
SM6 SM5
0
SM3 SM2 SM1 SM0
Serial I/O register (SIO)
AD conversion register (AD)
AD control register (ADCON)
0
0
ADVREF ADSTR ADIN2 ADIN1 ADIN0
?
0016
?
0016
?
0016
?
? ?
?
0 ?
? ?
0016
0 1
0016
?
? ?
?
?
?
?
?
0016
0016
?
0016
1 0
0016
0016
0016
?
?
0816
0
0
0
?
?
?
?
?
?
1
?
?
?
?
?
0
0
?
Rev. 1.0
106
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ SFR area (addresses E016 to FF16)
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
Bit allocation
Register
State immediately after reset
b0 b7
b7
E016
E116
E216
E316
E416
E516
E616
E716
E816
E916
EA16
EB16
EC16
ED16
EE16
EF16
F016
F116
F216
F316
F416
F516
F616
F716
F816
F916
FA16
FB16
FC16
FD16
FE16
FF16
Block H register (BHP)
b0
BHP5 BHP4 BHP3 BHP2 BHP1 BHP0
Block 1V register (B1VP)
B1VP7 B1VP6 B1VP5 B1VP4 B1VP3 B1VP2 B1VP1 B1VP0
Block 2V register (B2VP)
B2VP7 B2VP6 B2VP5 B2VP4 B2VP3 B2VP2 B2VP1 B2VP0
SPRITE control register (SC)
SC7 SC6 SC5 SC4 SC3 SC2 SC1 SC0
SPRITE H register (SHP)
SPRITE V register (SVP)
Color register 1 (CO1)
SHP7 SHP6 SHP5 SHP4 SHP3 SHP2 SHP1 SHP0
SVP7 SVP6 SVP5 SVP4 SVP3 SVP2 SVP1 SVP0
CO16 CO15 CO14 CO13 CO12 CO11 CO10
Color register 2 (CO2)
CO26 CO25 CO24 CO23 CO22 CO21 CO20
Color register 3 (CO3)
CO36 CO35 CO34 CO33 CO32 CO31 CO30
CO46 CO45 CO44 CO43 CO42 CO41 CO40
Color register 4 (CO4)
OSD control register (OC)
OC7 OC6 OC5 OC4 OC3 OC2 OC1 OC0
OSD I/O polarity control register (OPC)
Color register 5 (CO5)
OPC7 OPC6 OPC5 OPC4 OPC3 OPC2 OPC1 OPC0
CO56 CO55 CO54 CO53 CO52 CO51 CO50
Color register 6 (CO6)
CO66 CO65 CO64 CO63 CO62 CO61 CO60
Color register 7 (CO7)
CO76 CO75 CO74 CO73 CO72 CO71 CO70
Color register 8 (CO8)
CO86 CO85 CO84 CO83 CO82 CO81 CO80
0
0
0
0
?
?
?
?
?
?
?
?
0
0
0
0
?
?
?
?
?
?
?
?
0
0
0
0
0
0
Timer 1 (T1)
Timer 2 (T2)
Timer 3 (T3)
Timer 4 (T4)
Timer mode register 1 (TM1)
TM15 TM14 TM13 TM12 TM11 TM10
Timer mode register 2 (TM2)
TM25 TM24 TM23 TM22 TM21 TM20
PWM5 register (PWM5)
0016
0016
Test register
Test register
B1C4 B1C3 B1C2 B1C1 B1C0
Block 1 control register (B1C)
Block 2 control register (B2C)
B2C4 B2C3 B2C2 B2C1 B2C0
0
0
1
1
1
CM2
0
0
CPU mode register (CM)
Interrupt request register 1 (IREQ1)
IT3R IICR VSCR OSDR TM4R TM3R TM2R TM1R
Interrupt request register 2 (IREQ2)
Interrupt control register 1 (ICON1)
IT3E IICE VSCE OSDE TM4E TM3E TM2E TM1E
Interrupt control register 2 (ICON2)
0
MCSKR0 SPR S1R IT2R IT1R
A DR
A DE
0
MSE SPE S1E IT2E IT1E
0016
?
?
0016
0016
?
? ?
? ?
? ?
? ?
0016
0016
? ?
? ?
? ?
? ?
FF16
0716
FF16
0716
0016
0016
?
?
?
C?K0 ?
C?K0 ?
3C16
0016
0016
0016
0016
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
Rev. 1.0
107
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ 2 page register area (addresses 21016 to 21F16, 24016 to 24F16)
Bit allocation
:
Name
State immediately after reset
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
21016
21116
21216
21316
21416
21516
21616
21716
21816
21916
21A16
21B16
21C16
21D16
21E16
21F16
24016
24116
24216
24316
24416
24516
24616
24716
24816
24916
24A16
24B16
24C16
24D16
24E16
24F16
Register
Bit allocation
b7
State immediately after reset
b0 b7
b0
ROM correction address 1 (high-order)
ROM correction address 1 (low-order)
ROM correction address 2 (high-order)
ROM correction address 2 (low-order)
ROM correction enable register (RCR)
0
0
0
0
0
RCR2 RCR1RCR0
ROM correction address 3 (high-order)
ROM correction address 3 (low-order)
Left border control register (LBR)
Right border control register (RBR)
LBR6 LBR5 LBR4 LBR3 LBR2 LBR1 LBR0
RBR6 RBR5 RBR4 RBR3 RBR2 RBR1 RBR0
Top border control register (TBR) TBR7 TBR6 TBR5 TBR4 TBR3 TBR2 TBR1 TBR0
Bottom border control register (BBR) BBR7 BBR6 BBR5 BBR4 BBR3 BBR2 BBR1 BBR0
0016
Test register
DA2-H register (DA2H)
DA2-L register (DA2L)
0
0
?
?
?
?
?
?
?
?
0016
0016
0016
0016
0016
0016
0016
?
?
0016
0016
?
?
?
?
?
0016
?
?
?
?
?
?
?
? ?
?
?
?
Rev. 1.0
108
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Internal State of Processor Status Register and
Program Counter at Reset
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Register
Bit allocation
State immediately after reset
b0 b7
b7
Processor status register (PS)
Program counter (PCH)
Program counter (PCL)
N
V
T
B
D
I
Z
C
b0
? ? ? ? ? 1 ? ?
Contents of address FFFF16
Contents of address FFFE16
Rev. 1.0
109
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Structure of Register
The figure of each register structure describes its functions, contents
at reset, and attributes as follows:
<Example>
Bit position
Bit attributes(Note 2)
Values immediately after reset release (Note 1)
CPU Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
1 1
0 0
CPU mode register (CPUM) (CM) [Address 00FB16]
B
Name
0, 1 Processor mode bits
(CM0, CM1)
Stack page selection
bit (See note) (CM2)
Functions
b1 b0
0
0
1
1
A f t er r e R W
0
R W
0: Single-chip mode
1:
0:
Not available
1:
0: 0 page
1: 1 page
1
RW
3, 4 Fix these bits to “1.”
1
RW
5 Nothing is assigned. This bit is write disable bit.
When this bit is read out, the value is “1.”
C
b7 b6
6, 7 lock switch bits
(CM6, CM7)
0 0: f(XIN) = 8 MHz
0 1: f(XIN) = 12 MHz
1 0: f(XIN) = 16 MHz
1 1: Do not set
1
R W
0
RW
2
: Bit in which nothing is assigned
Notes 1: Values immediately after reset release
0 ••••••••••••••••••“0” after reset release
1 ••••••••••••••••••“1” after reset release
Indeterminate•••Indeterminate after reset release
2: Bit attributes••••••The attributes of control register bits are classified into 3 types : read-only, write-only
and read and write. In the figure, these attributes are represented as follows :
R••••••Read
W••••••Write
W ••••••Write enabled
R ••••••Read enabled
– ••••••Write disabled
– ••••••Read disabled
✽ ••••••“0” can be set by software, but “1”
cannot be set.
Rev. 1.0
110
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Addresses 00C116, 00C316, 00C516
Port Pi Direction Register
b7 b6 b5 b4 b3 b2 b1 b0
Port Pi direction register (Di) (i=0,1,2) [Addresses 00C1 16, 00C316, 00C516]
B
Name
0
Functions
After reset R W
0 : Port Pi0 input mode
1 : Port Pi0 output mode
0
R W
1
0 : Port Pi1 input mode
1 : Port Pi1 output mode
0
R W
2
0 : Port Pi2 input mode
1 : Port Pi2 output mode
0
R W
3
0 : Port Pi3 input mode
1 : Port Pi3 output mode
0
R W
4
0 : Port Pi4 input mode
1 : Port Pi4 output mode
0
R W
5
0 : Port Pi5 input mode
1 : Port Pi5 output mode
0
R W
6
0 : Port Pi6 input mode
1 : Port Pi6 output mode
0
R W
7
0 : Port Pi7 input mode
1 : Port Pi7 output mode
0
R W
Port Pi direction register
Address 00C716
Port P3 Direction Register
b7 b6 b5 b4 b3 b2 b1 b0
Port P3 direction register (D3) [Address 00C716 ]
B
0
Name
Functions
After reset R W
0 : Port P30 input mode
1 : Port P30 output mode
0
R W
1
0 : Port P31 input mode
1 : Port P31 output mode
0
R W
2
0 : Port P32 input mode
1 : Port P32 output mode
0
R W
Port P3 direction register
indeterminate R —
3, 4 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are indeterminate.
5
Port P3 direction register
0 : Port P35 input mode
1 : Port P35 output mode
0
R W
6
Port P30 output mode
selection bit (P30S)
0 : CMOS output
1 : N-channel open-drain output
0
R W
7
Port P31 output mode
selection bit (P31S)
0 : CMOS output
1 : N-channel open-drain output
0
R W
Rev. 1.0
111
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00C916
Port P35 Output Mode Control Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0
Port P35 output mode control register (P3S) [Address 00C916 ]
0
B
Name
Functions
0 to 3 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are in determinate.
4
Fix this bit to “0”
5
Port P35 output mode
selection bit (P35S)
6, 7
Fix these bits to “0”
0 : CMOS output
1 : N-channel open-drain
output
After reset
R W
Indeterminate R —
0
R W
0
R W
0
R W
Address 00CB16
OSD Port Control Register
b7 b6 b5 b4 b3 b2 b1 b0
0
0 0
OSD port control register (PF ) [Address 00CB16]
b
Name
Functions
0, 1 Fix these bits to “0”
After reset R W
0
R W
2
Port P52 output signal
selection bit (P52SEL)
0 : R signal output
1 : Port P52 output
0
R W
3
Port P53 output signal
selection bit (P53SEL)
0 : G signal output
1 : Port P53 output
0
R W
4
Port P54 output signal
selection bit (P54SEL)
0 : B signal output
1 : Port P54 output
0
R W
5
Port P55 output signal
selection bit (P55SEL)
0 : OUT1 signal output
1 : Port P55 output
0
R W
6
Port P10 output signal
selection bit (OUT2SEL)
0 : Port P10 signal output
1 : OUT2 output
0
R W
7
Fix this bit to “0”
0
R W
Rev. 1.0
112
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00CD16
Interrupt Input Polarity Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0
0
Interrupt input polarity register (IP) [Address 00CD16]
b
Name
0, 1 OSD clock
selection bits
(OCG0, OCG1)
Function
After reset R W
Function
b1 b0
0 0 The clock for OSD is supplied by connecting RC
or LC across the pins OSC1 and OSC2. However,
it is not corresponding to the bi-scan mode.
0
1 Since the main clock is used as the
clock for OSD, the oscillation
frequency is limited. Because of
this, the character size in width
(horizonal) direction is also limited.
In this case, pins OSC1 and OSC2
are also used as input ports P33
and P34 respectively.
1
0
1
1
0
R W
0
R W
OSD
oscillation
frequency =
f(XIN)
The clock for OSD is supplied by connecting LC
across the pins OSC1 and OSC2. In the bi-scan
mode, be sure to set this.
The clock for OSD is supplied by connecting the
following across the pins OSC1 and OSC2.
However, it is not corresponding to the bi-scan
mode.
• a ceramic resonator only for OSD and a
feedback resistor
• a quartz-crystal oscillator only for OSD and a
feedback resistor
2
Fix this bit to “0.”
3
INT1 polarity
switch bit (POL1)
0 : Positive polarity
1 : Negative polarity
0
R W
4
INT2 polarity
switch bit (POL2)
0 : Positive polarity
1 : Negative polarity
0
R W
5
INT3 polarity
switch bit (POL3)
0 : Positive polarity
1 : Negative polarity
0
R W
0
R W
6, 7 Fix these bits to “0.”
Rev. 1.0
113
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00D516
PWM Output Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0
PWM output control register 1 (PW) [Address 00D516]
B
Name
Functions
0 : Count source supply
0 DA1, DA2, PWM count
source selection bit (PW0) 1 : Count source stop
0 : DA1 output
1 DA1 output/P35
1 : P35 output
selection bit (PW1)
After reset R W
0
R W
0
R W
2 P00/PWM0 output
selection bit (PW2)
0: P00 output
1: PWM0 output
0
R W
3 P01/PWM1 output
selection bit (PW3)
0: P01 output
1: PWM1 output
0
R W
4 P02/PWM2 output
selection bit (PW4)
0: P02 output
1: PWM2 output
0
R W
5 P03/PWM3 output
selection bit (PW5)
0: P03 output
1: PWM3 output
0
R W
6 P04/PWM4 output
selection bit (PW6)
0: P04 output
1: PWM4 output
0
R W
7 P05/PWM5 output
selection bit (PW7)
0: P05 output
1: PWM5 output
0
R W
Address 00D616
PWM Output Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0 0
0 0
PWM output control register 2 (PN) [Address 00D616]
B
Name
0, 1 Fix these bits to “0.”
Functions
After reset R W
0
R W
2 DA1 output polarity
selection bit (PN3)
0 : Positive polarity
1 : Negative polarity
0
R W
3 PWM output polarity
selection bit (PN4)
0 : Positive polarity
1 : Negative polarity
0
R W
4 DA2 output polarity
selection bit (PN5)
0 : Output LOW
1 : Output HIGH
0
R W
5 P17/DA2 output
selection bit (PN5)
0 : P17
1 : DA2
0
R W
0
R W
6, 7 Fix these bits to “0.”
Rev. 1.0
114
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00D716
I2C Data Shift Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C data shift register (S0) [Address 00D716 ]
B
0
to
7
Name
Functions
D0 to D7 This is an 8-bit shift register to store
receive data and write transmit data.
After reset
R W
Indeterminate
R W
Note: To write data into the I2C data shift register after setting the MST bit to
“0” (slave mode), keep an interval of 8 machine cycles or more.
Address 00D816
I2C Address Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C address register (S0D) [Address 00D816]
B
Name
Functions
After reset R W
0
Read/write bit
(RBW)
<Only in 10-bit addressing (in slave) mode>
The last significant bit of address data is
compared.
0: Wait the first byte of slave address after
START condition
(read state)
1: Wait the first byte of slave address after
RESTART condition
(write state)
0
R —
1
to
7
Slave address
(SAD0 to SAD6)
<In both modes>
The address data is compared.
0
R W
Rev. 1.0
115
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00D916
I2C Status Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C status register (S1) [Address 00D916]
B
Name
0
Functions
Last receive bit (LRB)
(See note)
0 : Last bit = “0 ”
1 : Last bit = “1 ”
1
General call detecting flag
(AD0) (See note)
2
3
After reset R W
Indeterminate
R —
0 : No general call detected
1 : General call detected
(See note)
0
R —
Slave address comparison
flag (AAS) (See note)
0 : Address mismatch
1 : Address match
0
R —
Arbitration lost detecting flag
(AL) (See note)
0 : Not detected
1 : Detected
0
R —
1
R W
0 : Bus free
1 : Bus busy
0
R W
b7
0
0
1
1
0
R W
4
I2C-BUS interface interrupt
request bit (PIN)
5
Bus busy flag (BB)
6, 7 Communication mode
specification bits
(TRX, MST)
(See note)
(See note)
(See note)
0 : Interrupt request issued
1 : No interrupt request issued
b6
0 : Slave recieve mode
1 : Slave transmit mode
0 : Master recieve mode
1 : Master transmit mode
Note : These bits and flags can be read out, but cannnot be written.
Address 00DA16
I2C Control Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C control register (S1D) [Address 00DA16]
B
Name
Functions
After reset R W
0
to
2
Bit counter
(Number of transmit/recieve
bits)
(BC0 to BC2)
b2
0
0
0
0
1
1
1
1
b0
0: 8
1: 7
0: 6
1: 5
0: 4
1: 3
0: 2
1: 1
0
R W
3
I2C-BUS interface use
enable bit (ESO)
0: Disabled
1: Enabled
0
R W
4
Data format selection
bit(ALS)
0: Addressing format
1: Free data format
0
R W
5
Addressing format selection
bit (10BIT SAD)
0: 7-bit addressing format
1: 10-bit addressing format
0
R W
b7 b6 Connection port (See note)
0 0: None
0 1: SCL1, SDA1
1 0: SCL2, SDA2
1 1: SCL1, SDA1, SCL2, SDA2
0
R W
6, 7 Connection control bits
between I2C-BUS interface
and ports
(BSEL0, BSEL1)
b1
0
0
1
1
0
0
1
1
Note: When using ports P11-P14 as I2C-BUS interface, the output structure changes
automatically from CMOS output to N-channel open-drain output.
Rev. 1.0
116
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00DB16
I2C Clock Control Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C clock control register (S2) [Address 00DB16]
B
0
to
4
Name
Functions
After reset R W
SCL frequency control bits Setup value of Standard clock High speed
(CCR0 to CCR4)
CCR4–CCR0
mode
clock mode
0 0 to 0 2
Setup disabled
04
Setup disabled
250
05
100
83.3
400 (See note)
333
166
...
500/CCR value 1000/CCR value
1D
17.2
34.5
1E
16.6
33.3
32.3
1F
R W
Setup disabled Setup disabled
03
06
0
16.1
(at φ = 4 MHz, unit : kHz)
5
SCL mode
specification bit
(FAST MODE)
0: Standard clock mode
1: High-speed clock mode
0
R W
6
ACK bit
(ACK BIT)
0: ACK is returned.
1: ACK is not returned.
0
R W
7
ACK clock bit
(ACK)
0: No ACK clock
1: ACK clock
0
R W
Note: At 400 kHz in the high-speed clock mode, the duty is as below .
“0” period : “1” period = 3 : 2
In the other cases, the duty is as below.
“0” period : “1” period = 1 : 1
Rev. 1.0
117
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00DC16
Serial I/O Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0
Serial I/O mode register (SM) [Address 00DC16]
B
Name
0, 1 Internal synchronous
clock selection bits
(SM0, SM1)
Functions
b1 b0
0 0: f(XIN)/4
0 1: f(XIN)/16
1 0: f(XIN)/32
1 1: f(XIN)/64
After reset R W
0
R W
2
Synchronous clock
selection bit (SM2)
0: External clock
1: Internal clock
0
R W
3
Serial I/O port
selection bit (SM3)
0: P20, P21
1: SCLK, SOUT
0
R W
0
R W
4 Fix this bit to “0.”
5
Transfer direction
selection bit (SM5)
0: LSB first
1: MSB first
0
R W
6
Serial input pin
selection bit (SM6)
0: Input signal from SIN pin.
1: Input signal from SOUT pin.
0
R W
7
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
0
R —
Address 00DF16
A-D Control Register
b7 b6 b5 b4 b3 b2 b1 b0
0
0
A-D control register (ADCON) [Address 00DF16]
B
Name
Functions
After reset R W
0
R W
0: Conversion in progress
1: Convertion completed
1
R W
0: OFF
1 : ON
0
R W
0
R W
Indeterm inate
R —
0
R W
0
to
2
Analog input pin selection
bits
(ADIN0 to ADIN2)
b2
0
0
0
0
1
1
1
1
b1
0
0
1
1
0
0
1
1
b0
0 : A-D1
1 : A-D2
0 : A-D3
1 : A-D4
0 : A-D5
1 : A-D6
0 : A-D7
1 : A-D8
3
A-D conversion completion
bit (ADSTR)
4
VCC connection selection bit
(ADVREF)
5
Fix this bit to “0.”
6
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is indeterminate.
7
Fix this bit to “0.”
Rev. 1.0
118
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00E016
Block H Register
b7 b6 b5 b4 b3 b2 b1 b0
Horizontal position register (HP) [Address 00E016]
B
Name
Functions
After reset R W
0 Control bits of horizontal Horizontal display start positions = Tdef1 + 4TOSC ✕ n
to display start positions (n: setting value, Tdef1: 31TOSC,
5 (BHP0 to BHP5)
TOSC: OSD oscillation cycle)
(See note 1)
6, 7 Nothing is assigned. These bits are write disable bits.
W h en t h e s e b i t s a r e re a d o u t, t h e v a l u e s a r e “0 . ”
0
RW
0
R—
Note: The setting value synchronizes with the VSYNC.
Addresses 00E116 and 00E216
Block i V Register
b7 b6 b5 b4 b3 b2 b1 b0
Block i V register (BiVP) (i = 1, 2) [Addresses 00E116 and 00E216]
B
Name
Functions
0 Control bits of
Vertical display start positions = Hdef + H ✕ n
to vertical display
(n: setting value, Hdef: 17H, H: HSYNC)
7 start positions
(BiVP0 to BiVP7)
(See note 1)
After reset R W
Indeterminate R W
Note: Set values except “0016” to BiVP.
Rev. 1.0
119
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00E316
SPRITE Control Register
b7 b6 b5 b4 b3 b2 b1 b0
SPRITE control register (SC) [Address 00E316]
B
Name
Functions
After reset R W
0, 1 SPRITE font 1
color register
specification bit
(SC0, SC1)
SC1
0
0
1
1
@SC0
0: Color
1: Color
0: Color
1: Color
register 1
register 2
register 3
register 4
2, 3 SPRITE font 2
color register
specification bit
(SC2, SC3)
SC3
0
0
1
1
@SC2
0: Color
1: Color
0: Color
1: Color
register 1
register 2
register 3
register 4
4, 5 SPRITE font selection bit
(SC4, SC5)
SC5 SC4 Character code
SPRITE1 SPRITE2
0
0
1
1
6, 7 SPRITE/raster patterning
control bit
(SC6, SC7)
(See note)
SC7
0
0
1
1
0
1
0
1
F816
FA16
FC16
FE16
0
R W
0
R W
0
R W
0
R W
F916
FB16
FD16
FF16
@SC6
0: Display OFF
1: Do not set
0: SPRITE display
1: Raster patterning
display
Note : This bit is valid when bit 0 of the OSD control register to “1.”
Rev. 1.0
120
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00E416
SPRITE H Register
b7 b6 b5 b4 b3 b2 b1 b0
SPRITE H register (SHP) [Address 00E416]
B
Name
Functions
0 Horizontal display Horizontal display start position
to start position
= Tdef2 + 2TOSC ✕ n
7 control bits of
(n: setting value, Tdef2: 2TOSC,
TOSC: OSD oscillation cycle)
SPRITE OSD
(SHP0 to SHP7)
After reset R W
0
R W
Notes 1: Set values except “0016” to “0216” to SHP.
2: When selecting raster patterning display, setting value is
synchronized with VSYNC signal; when selecting SPRITE
display, it is not synchronized.
Address 00E516
SPRITE V Register
b7 b6 b5 b4 b3 b2 b1 b0
SPRITE V register (SVP) [Address 00E516]
B
Name
Functions
After reset R W
0 Horizontal display Horizontal display start position Indeterminate R W
to start position
= Hdef + H ✕ n
7 control bits of
(n: setting value, Hdef: 17H, H: HSYNC)
SPRITE OSD
(SVP0 to SVP7)
(See note 1)
Note: Set values except “0016” to the SVP.
Rev. 1.0
121
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Addresses 00E616 to 00E916 and 00EC16 to 00EF16
Color Register i
b7 b6 b5 b4 b3 b2 b1 b0
Color register i (CO1 to CO8) (i=1 to 8) [Addresses 00E616 to 00E916, 00EC16 to 00EF16]
B
Name
@
Functions
After re set
R W
0
R signal output selection
bit (COi0)
0: No output
1: Output
Indeterminate R W
1
G signal output selection
bit (COi1)
0: No output
1: Output
Indeterminate R W
2
B signal output selection
bit (COi2)
0: No output
1: Output
Indeterminate R W
3
R signal output (background) 0: No output
selection bit (COi3)
1: Output
Indeterminate R W
4
G signal output (background) 0: No output
selection bit (COi4)
1: Output
Indeterminate R W
5
B signal output (background) 0: No output
1: Output
selection bit (COi5)
Indeterminate R W
6
OUT1 output control bit
(COi6)
Indeterminate R W
7
Nothing is assined. This bit is a write disable bit.
When this bit is read out, the value is “0.”
0: Character output
1: Blank output
0
R —
Rev. 1.0
122
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00EA16
OSD Control Register
b7 b6 b5 b4 b3 b2 b1 b0
OSD control register (OC) [Address 00EA16]
B
0
1
Name
OSD control bit
(OC0) (See note 1)
Border type selection
bit (OC1)
2, 3 Window horizontal
position minute
adjustment bit
(OC2, OC3)
4 Window control bit
(OC4)
Functions
0 : All-blocks display OFF
1 : All-blocks display ON
0 : All bordered
1 : Shadow bordered (See note 2)
b3
0
0
1
1
b2
(See notes 3 and 4)
0 : Standard
1 : Standard + 1TOSC
0 : Standard + 2TOSC
1 : Standard + 3TOSC
0 : Window OFF
1 : Window ON
5 Scan mode selection 0 : Normal scan mode
bit (OC5)
1 : Bi-scan mode (See note 5)
After reset R W
0
R W
0
R W
0
R W
0
R W
0
R W
6
Raster color OUT1
control bit (OC6)
0 : No output
1 : Output
0
R W
7
Raster color OUT2
control bit (OC7)
0 : No output
1 : Output
0
R W
Notes 1 : Even this bit is switched during display, the display screen
remains unchanged until a rising (falling) of the next VSYNC.
2 : Shadow border is output at right and bottom side of the font.
3 : TOSC = OSD oscillation cycle
4 : These bits are vallid for both left border and right border (for detail, refer
to “(8) Window Function.”)
5 : When setting to bi-scan mode, connect LC between pins OSC1 and
OSC2.
Rev. 1.0
123
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00EB16
OSD I/O Polarity Register
b7 b6 b5 b4 b3 b2 b1 b0
OSD I/O polarity register (OPC) [Address 00EB16]
B
Name
Functions
Af t er r e R W
0
HSYNC input polarity
switch bit (OPC0)
0 : Positive polarity input
1 : Negative polarity input
0
R W
1
VSYNC input polarity
switch bit (OPC1)
0 : Positive polarity input
1 : Negative polarity input
0
R W
2
R/G/B output polarity switch 0 : Positive polarity output
1 : Negative polarity output
bit (OPC2)
0
R W
3
OUT1 output polarity
switch bit (OPC3)
0 : Positive polarity output
1 : Negative polarity output
0
R
4
OUT2 output polarity
switch bit (OPC4)
0 : Positive polarity output
1 : Negative polarity output
0
R W
5
Raster color R control
bit (OPC5)
0 : No output
1 : Output
0
R W
6
Raster color G control bit
(OPC6)
0 : No output
1 : Output
0
R W
7
Raster color B control bit
(OPC7)
0 : No output
1 : Output
0
R W
W
Rev. 1.0
124
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00F416
Timer Mode Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Timer mode register 1 (TM1) [Address 00F416]
B
Name
Functions
0
Timer 1 count source
selection bit 1 (TM10)
0: f(XIN)/16
1: f(XIN)/4096
0
R W
1
Timer 2 count source
selection bit 1 (TM11)
0: Interrupt clock source
1: External clock from TIM2 pin
0
R W
2 Timer 1 count
stop bit (TM12)
0: Count start
1: Count stop
0
R W
3 Timer 2 count stop bit
(TM13)
0: Count start
1: Count stop
0
R W
4 Timer 2 internal count source 0: f(XIN)/16
1: Timer 1 overflow
selection bit 2 (TM14)
0
R W
5 <At execution of STP
instruction>
Timers 3 and 4 auto
set disable bit (TM15)
0
R W
0
R —
0: Auto set enabled
1: Auto set disabled
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
After reset R W
Address 00F516
Timer Mode Register 2
b7 b6 b5 b4 b3 b2 b1 b0
Timer mode register 2 (TM2) [Address 00F516]
B
Name
0 Timer 3 count source
selection bit (TM20)
1
Functions
0 : f(XIN)/16
1 : External clock source
After reset R W
0
R W
0 : Timer 3 overflow signal
1 : f(XIN)/16
0
R W
2 Timer 3 count stop bit
(TM22)
0: Count start
1: Count stop
0
R W
3 Timer 4 count stop bit
(TM23)
0: Count start
1: Count stop
0
R W
4 Timer 4 count source
selection bit (TM24)
0: Internal clock source
1: f(XIN)/2
0
R W
0
R W
0
R —
5
Timer 4 internal
interrupt count source
selection bit (TM21)
Timer 3 external count
0: TIM3 pin input
source selection bit (TM25) 1: HSYNC pin input
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
Rev. 1.0
125
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Addresses 00F916 and 00FA16
Block i Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Block i control register (BiC) (i = 1, 2) [Addresses 00F916, 00FA16]
B
0
to
2
3, 4
Name
b2
Display mode
✕
selection bits
0
(BiC0 to BiC2)
0
1
1
Dot size selection bit b4
(BiC3, BiC4)
0
0
1
1
b1
0
0
1
0
1
b3
0
1
0
1
b0
0
1
0
1
0
Functions
After reset R W
Display mode
Indeterminate R W
Display OFF
OSD mode (no border)
BUTTON mode (no border)
OSD mode (border)
BUTTON mode (border)
Indeterminate R W
Dot size
1TOSC ✕ 1H
Do not set
2TOSC ✕ 2H
3TOSC ✕ 3H
5 Nothing is assigned. These bits are write disable bits.
to When these bits are read out, the values are “0.”
7
0
R—
Notes 1 : TOSC = OSD oscillation cycle
2 : H = HSYNC
Address 00FB16
CPU Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0 1 1 1
0 0
CPU mode register (CM) [Address 00FB16]
B
Name
Functions
After reset R W
0
R W
1
R W
3 to 5 Fix these bits to “1.”
1
R W
6, 7 Fix these bits to “0.”
0
R W
0, 1 Processor mode bits
(CM0, CM1)
2 Stack page selection
bit (CM2) (See note)
b1 b0
0
0
1
1
0: Single-chip mode
1:
0:
Not available
1:
0: 0 page
1: 1 page
Note: This bit is set to “1” after the reset release.
Rev. 1.0
126
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00FC16
Interrupt Request Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Interrupt request register 1 (IREQ1) [Address 00FC16]
B
Name
0 Timer 1 interrupt
request bit (TM1R)
Functions
After reset
0
0 : No interrupt request issued
1 : Interrupt request issued
Timer 2 interrupt
0
0 : No interrupt request issued
request bit (TM2R) 1 : Interrupt request issued
0
Timer 3 interrupt
0 : No interrupt request issued
request bit (TM3R) 1 : Interrupt request issued
0
Timer 4 interrupt
0 : No interrupt request issued
request bit (TM4R) 1 : Interrupt request issued
OSD interrupt request 0 : No interrupt request issued
0
1 : Interrupt request issued
bit (OSDR)
VSYNC interrupt
0
0 : No interrupt request issued
request bit (VSCR) 1 : Interrupt request issued
0
Multi-master I2C-BUS interface 0 : No interrupt request issued
interrupt request bit (IICR)
1 : Interrupt request issued
INT3 external interrupt 0 : No interrupt request issued
0
request bit (IT3R)
1 : Interrupt request issued
R W
R ✽
1
R ✽
2
3
4
5
6
7
R ✽
R ✽
R ✽
R ✽
R ✽
R ✽
✽: “0” can be set by software, but “1” cannot be set.
Address 00FD16
Interrupt Request Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt request register 2 (IREQ2) [Address 00FD16]
B
Name
Functions
After reset
0 INT1 external interrupt 0 : No interrupt request issued
0
1 : Interrupt request issued
request bit (IT1R)
0
1 INT2 external interrupt 0 : No interrupt request issued
1 : Interrupt request issued
request bit (IT2R)
2 Serial I/O interrupt
0
0 : No interrupt request issued
request bit (S1R)
1 : Interrupt request issued
0
3 SPRITE OSD interrupt 0 : No interrupt request issued
request bit (SPR)
1 : Interrupt request issued
0
4 f(XIN)/4096 interrupt 0 : No interrupt request issued
request bit (MSR)
1 : Interrupt request issued
5 Nothing is assigned. This bit is a write disable bit.
0
When this bit is read out, the value is “0.”
0
6 A-D conversion interrupt 0 : No interrupt request issued
request bit (ADR)
1 : Interrupt request issued
7
Fix this bit to “0.”
0
R W
R ✽
R ✽
R ✽
R ✽
R ✽
R —
R ✽
R W
✽: “0” can be set by software, but “1” cannot be set.
Rev. 1.0
127
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Addresses 00FE16
Interrupt Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Interrupt control register 1 (ICON1) [Address 00FE16]
B
Name
Functions
After reset R W
0 Timer 1 interrupt
enable bit (TM1E)
1 Timer 2 interrupt
enable bit (TM2E)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
2 Timer 3 interrupt
enable bit (TM3E)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
3 Timer 4 interrupt
enable bit (TM4E)
4 OSD interrupt enable bit
(OSDE)
5 VSYNC interrupt enable
bit (VSCE)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
6 Multi-master I2C-BUS interface 0 : Interrupt disabled
interrupt enable bit (IICE)
1 : Interrupt enabled
0
R W
7 INT3 external interrupt
enable bit (IT3E)
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
Address 00FF16
Interrupt Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt control register 2 (ICON2) [Address 00FF16]
B
Name
0 INT1 external interrupt
enable bit (IT1E)
1 INT2 external interrupt
enable bit (IT2E)
2 Serial I/O interrupt
enable bit (S1E)
S
PRITE OSD interrupt
3
enable bit (SPE)
4 f(XIN)/4096 interrupt
enable bit (MSE)
5 Fix this bit to “0.”
Functions
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
6 A-D conversion interrupt 0 : Interrupt disabled
enable bit (ADE)
1 : Interrupt enabled
N
o
t
h
i
n
g
i
s
a
s
s
i
g
n
e
d
.
T
h
i
s
b
it is a write disable
7
bit. When this bit is read out, the value is “0.”
After reset R W
0
R W
0
R W
0
R W
0
R W
0
R W
0
R W
0
R W
0
R —
Rev. 1.0
128
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 021B16
ROM Correction Enable Register
b7 b6 b5 b4 b3 b2 b1 b0
ROM correction enable register (RCR) [Address 021B16]
0 0 0 0 0
B
Name
Functions
After reset R W
0
Vector 1 enable bit (RCR0)
0: Disabled
1: Enabled
0
R W
1
Vector 2 enable bit (RCR1)
0: Disabled
1: Enabled
0
R W
2
Vector 3 enable bit (RCR2)
0: Disabled
1: Enabled
0
R W
3
to
7
Fix these bits to “0.”
0
R W
Address 024016
Left Border Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Left border control register (LBR) [Address 024016]
B
Name
Functions
0
to
6
Control bits of
left border
(LBR0 to LBR6)
7
Nothing is assigned. This bit is write disable bit.
When this bit is read out, the value is indeterminate.
Left border position = Tdef4 + 4TOSC ✕ n + 1TOSC ✕ WH
(n: setting value, Tde f4: 4TOSC,
TOSC: OSD oscillation cycle,
After re set R W
0
R
W
0
R
—
WH: value (0 to 3) of window horizontal position minute adjustment bit)
Note: Set values fit for LBR ≤ RBR.
Address 024116
Right Border Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Right border control register (RBR) [Address 024116]
B
Name
0
to
6
Control bits of
left border
(RBR0 to RBR6)
Functions
Right border position = Tdef4 + 4TOSC ✕ n + 1TOSC ✕WH
(n: setting value, Tde f4: 4TOSC,
TOSC: OSD oscillation cycle,
After re set R W
0
R
W
0
R
—
WH: value (0 to 3) of window horizontal position minute adjustment bit)
7
Nothing is assigned. This bit is write disable bit.
When this bit is read out, the value is indeterminate.
Note: Set values fit for LBR ≤ RBR.
Rev. 1.0
129
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 024516
Top Border Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Top border control register (TBR) [Address 024516]
B
Name
Functions
0 Control bits of
Top border position = Hdef + H ✕ n
to top border
(n: setting value, Hdef: 17H, H: HSYNC)
7 (TBR0 to TBR7)
After reset R W
Indeterminate R W
Notes 1: Set values except “0016” to TBR.
2: Set values fit for TBR ≤ BBR.
Address 024616
Bottom Border Control Register
b7 b6 b5 b4 b3 b2 b1 b0
Bottom border control register (BBR) [Address 024616]
B
Name
Functions
0 Control bits of
Bottom border position = Hdef + H ✕ n
to bottom border
(n: setting value, Hdef: 17H, H: HSYNC)
7 (BBR0 to BBR7)
After reset R W
Indeterminate R W
Notes 1: Set values except “0016” to BBR.
2: Set values fit for TBR ≤ BBR.
Rev. 1.0
130
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
21. PACKAGE OUTLINE
42P4B
Plastic 42pin 600mil SDIP
Weight(g)
4.1
JEDEC Code
–
Lead Material
Alloy 42/Cu Alloy
22
1
21
E
42
e1
c
EIAJ Package Code
SDIP42-P-600-1.78
Symbol
L
A1
A
A2
D
e
SEATING PLANE
b1
b
b2
A
A1
A2
b
b1
b2
c
D
E
e
e1
L
Dimension in Millimeters
Min
Nom
Max
–
–
5.5
0.51
–
–
–
3.8
–
0.35
0.45
0.55
0.9
1.0
1.3
0.63
0.73
1.03
0.22
0.27
0.34
36.5
36.7
36.9
12.85
13.0
13.15
–
1.778
–
–
15.24
–
3.0
–
–
0°
–
15°
Rev. 1.0
131
MITSUBISHI MICROCOMPUTERS
M37225M6–XXXSP, M37225M8–XXXSP
M37225ECSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
HEAD OFFICE: 2-2-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Keep safety first in your circuit designs!
•
Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable
material or (iii) prevention against any malfunction or mishap.
•
These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property
rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party.
Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples
contained in these materials.
All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by
Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product
distributor for the latest product information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com).
When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision
on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein.
Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric
Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical,
aerospace, nuclear, or undersea repeater use.
The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials.
If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved
destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
Notes regarding these materials
•
•
•
•
•
•
•
© 1999 MITSUBISHI ELECTRIC CORP.
New publication, effective Sep. 1999.
Specifications subject to change without notice.
REVISION DESCRIPTION LIST
Rev.
No.
1.0
M37225M6-XXXSP, M37225M8-XXXSP
M37225ECSP (Rev.1.0) TENTATIVE SPECIFICATIONS
Revision Description
First Edition
Rev.
date
9909
(1/1)