MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY DESCRIPTION M61314SP is Semiconductor Integrated Circuit for CRT Display Monitor. It includes OSD Blanking,OSD Mixing,Retrace Blanking,Video detector,Sync Sepa ,Wide band Amplifer. Brightness Control, Main/Sub Contrast,OSD level, 4ch D/A OUT,Video response adjust can be controlled by I2C Bus. PIN CONFIGURATION (TOP VIEW) GND R IN Vcc 1(12V) G IN SonG IN GND1 B IN GND2 Sync Sepa.OUT Video det.OUT Vcc3(5V) OSD BLK IN FEATURES Frequency Band Width RGB: 180MHz (3Vp-p at -3dB) OSD: 80MHz OSD R IN OSD G IN OSD B IN GND3 Input RGB: 0.7Vp-p(typical) OSD: 3.5V~5V(positive) OSD BLK: 3.5V~5V(positive) Retrace BLK: 2.5V~5V(positive) Clamp Pulse: 2.5V~5V(positive) Output RGB: OSD: Sync OUT: NC(GND) ABL IN 1 2 3 4 5 6 7 8 9 32 10 23 R OUT Vcc 2(12V) G OUT GND4 B OUT NC(GND) D/A OUT 4 D/A OUT 3 11 22 D/A OUT 2 12 21 13 20 31 30 29 28 27 26 25 24 14 19 15 18 D/A OUT 1 SCL SDA Clamp pulse IN 16 17 Ret.BLK IN Package:32P4B 5Vp-p (at Brightness less than 2V DC) 4Vp-p (at Brightness less than 2V DC) 5Vp-p 32 pin plastic SDIP RECOMMENDED OPERATING CONDITIONS Supply Voltage Range Rated Supply Voltage 11.50V ~ 12.50V (V3,V29) 4.75V ~ 5.25V (V11) 12.00V (V3,V29) 5.00V (V11) APPLICATION EXAMPLE CRT Display Monitor MITSUBISHI ELECTRIC 1 MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY ABSOLUTE M AXIMUM RATINGS(Ambient temperature 25ºC) Symbol Rating Unit Vcc12 13.0 V Vcc5 6.0 V Pd 2358 mW Ambient temperature Topr -20 ~ +75 ºC Storage temperature Tstg -40 ~ +150 ºC Recommend supply 12 Vopr12 12.0 V Recommend supply 5 Vopr5 5.0 V Vopr'12 11.5 ~ 12.5 V 4.75 ~ 5.25 V Parameter Supply voltage(Pin3,29) Supply voltage(Pin11) Power dissipation Voltage range 12 Voltage range 5 Vopr'5 THERM AL DERATING 2800 2400 2358 2000 1600 1415 1200 800 400 -25 0 25 50 75 100 125 150 Ambient Temperature Ta (ºC) MITSUBISHI ELECTRIC 2 MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY BLOCK DIAGRAM MITSUBISHI ELECTRIC 3 MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY BUS CONTROL TABLE (1)Slave address: D7 D6 D5 D4 D3 D2 D1 R/W 1 0 0 0 1 0 0 0 (2) Slave receiver format: normal mode 8bit S SLAVE ADDRESS =88H 8bit A SUB ADDRESS 8bit DATA BY TE A A P auto increment mode 8bit S SLAVE ADDRESS 8bit DATA (SUB ADD.=0(X+1)H) 8bit A A SUB ADDRESS (0XH)+10H 8bit DATA (SUB ADD.=0(X+2)H) MITSUBISHI ELECTRIC A A 8bit DATA (SUB ADD.=0XH) A S : Start condition A : Acknowledge P : Stop condition 4 MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY SDA, SCL CHARACTERISTIC parameter sy m bol MIN MAX unit min. input LOW voltage V IL -0.5 1.5 V max. input HIGH voltage V IH 3.0 5.5 V SCL clock frequency. fSCL 0 400 KHz Time the bus must be free before a new transmission can start. tBUF 1.3 - µs tHD:STA 0.6 - µs The LOW period of the clock tLOW 1.3 - µs The HIGH period of the clock tHIGH 0.6 - µs Set -up time for start condition.(Only relevant for a repeated Start condition. tSU:STA 0.6 - µs Hold time DATA. tHD:DAT 0 0.9 µs Set-up time DATA tSU:DAT 100 - ns Rise time both SDA and SCL lines. tR 300 ns Fall time both SDA and SCL lines. tF 300 ns Set-up time for stop condition tSU:STO Hold time start condition.After this period the first clock pulse is generated. 20+ 0.1Cb 20+ 0.1Cb 0.6 µs - tR, tF tBUF V IH SDA V IL tHD:STA tHD:DAT tSU:DAT tSU:STO tSU:STA V IH SCL V IL tLOW S tHIGH S MITSUBISHI ELECTRIC P S 5 MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY (3) Pre - Amp Block sub address byte and data byte format sub add. 00H f unction Main contrast Brightness 01H control bit Data Byte (top:byte format under:start condition) D7 D6 D5 D4 D3 D2 D1 D0 8 A07 0 A06 0 A05 0 A04 0 A03 0 A02 0 A01 0 A00 1 8 A17 0 A16 0 A15 0 A14 0 A13 0 A12 0 A11 0 A10 1 02H Sub contrast R 8 A27 0 A26 0 A25 0 A24 0 A23 0 A22 0 A21 0 A20 1 03H Sub contrast G 8 A37 0 A36 0 A35 0 A34 0 A33 0 A32 0 A31 0 A30 1 04H Sub contrast B 8 A47 A46 0 0 A45 0 A44 0 A43 0 A42 0 A41 0 A40 1 A56 0 A55 A54 0 0 A53 0 A52 0 A51 0 A50 1 A66 A65 A64 A63 A62 A61 A60 0 A77 0 0 A76 0 0 A75 0 0 A74 0 0 A73 0 0 A72 0 0 A71 0 1 A70 1 A87 0 A86 0 A85 0 A84 0 A83 0 A82 0 A81 0 A80 1 A97 A96 A95 A94 A93 A92 A91 A90 0 - 0 - 0 - 0 - - - - - - - - AA4 - - AA5 0 05H OSD lev el 7 06H D/A OUT1 8 07H D/A OUT2 8 08H D/A OUT3 8 09H D/A OUT4 8 Sharpness 0AH control 4 Sy nc Sepa SW 1 Video Det SW 1 Test mode 2 A67 AA7 AA6 0 0 0 0 0 1 AA3 AA2 AA1 AA0 0 - 0 - 0 - 1 - - - - - - 0 - - - - - - - - - - - - *)pre-data *)subadd. 0AH Sync Sepa SW AA4 0:Sync Sepa ON 1:Sync Sepa OFF Video Det SW AA5 0:Video Det ON 1:Video Det OFF Always set up as AA6 and AA7 in 0 For IIC Data, please transfer in the period of Vertical. MITSUBISHI ELECTRIC 6 MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY ELECTRICAL CHARACTERISTICS Sub Contrast Control Characteristics Main Contrast Control Characteristics 6 6 4 4 2 2 Main Contrast : Max ABL : 5V Sub Contrast : Max ABL : 5V 0 00H 6 Main Contrast Control Data FFH 0 00H Sub Contrast Control Data FFH ABL Characteristics Brightness Control Characteristics 6 4 4 2 2 Main Contrast:Max Sub Contrast :Max 0 00H 6 Brightness Control Data 0 FFH 0 OSD Adjust Control Characteristics 5 D/A OUT Control Characteristics 6 4 4 2 2 0 00H ABL Control Voltage (VDC) OSD Adjust Control Data 7FH 0 00H MITSUBISHI ELECTRIC D/A OUT Control Data FFH 7 MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY APPLICATION EXAMPLE CRT 110V Cut Off Adj 12V DAC OUT ×4 3K 3K 3K 0.01µ ABL IN 0~5VDC SCL 47µ 100 0.01µ 32 31 0.01µ 0.01µ 0.01µ SDA 0.01µ 100µH 29 30 28 27 26 25 24 23 21 22 20 19 18 17 BLK IN (for retrace) M61314SP 1 2 3 4 6 5 8 7 9 10 11 12 1µ 50K 75 0.01µ 75 ClampPulse IN 1K + 75 0.01µ 47µ 13 14 15 16 15 OSD (B) OSD OSD (G) OSD (R) BLK + 47µ INPUT 12V INPUT (G) (R) SonG IN INPUT (B) Sync Video 5V Sepa. Det. OUT OUT "Purchase of Mitsubishi electric corporation's I 2C components conv ey s a licence under the Philips I 2C Patent Rights to use these components in an I 2C sy stem, prov ided that the sy stem conf orms the I 2C Standard Specif ication as def ined by Philips" MITSUBISHI ELECTRIC 8 SEATING PLANE 1 32 EIAJ Package Code SDIP32-P-400-1.78 A L MITSUBISHI ELECTRIC e JEDEC Code – D b1 Weight(g) 2.2 b Lead Material Alloy 42/Cu Alloy 16 17 b2 A2 A1 A A1 A2 b b1 b2 c D E e e1 L Symbol Plastic 32pin 400mil SDIP c Dimension in Millimeters Min Nom Max – – 5.08 0.51 – – – 3.8 – 0.35 0.45 0.55 0.9 1.0 1.3 0.63 0.73 1.03 0.22 0.27 0.34 27.8 28.0 28.2 8.75 8.9 9.05 – 1.778 – – 10.16 – 3.0 – – 0° – 15° e1 32P4B MITSUBISHI ICs (MONITOR) M61314SP I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY 2 DETAILED DIAGRAM OF PACKAGE OUTLINE 9 E MITSUBISHI ICs (MONITOR) M61314SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY Keep safety first in your circuit designs! lMitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials lThese materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer´s application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. lMitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party´s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. lAll information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com). lWhen using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. lMitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. lThe prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. lIf these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. lPlease contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein. MITSUBISHI ELECTRIC 10