SEMICONDUCTOR TECHNICAL DATA The MC10H160 is a 12–bit parity generator–checker. The output goes high when an odd number of inputs are high providing the odd parity function. Unconnected inputs are pulled to a logic low allowing parity detection and generation for less than 12 bits. The MC10H160 is a functional pin duplication of the standard 10K family part with 100% improvement in propagation delay and no increase in power–supply current. L SUFFIX CERAMIC PACKAGE CASE 620–10 P SUFFIX PLASTIC PACKAGE CASE 648–08 • Propagation Delay, 2.5 ns Typical • Power Dissipation, 320 mW Typical • Improved Noise Margin 150 mV (Over Operating Voltage and Temperature Range) • Voltage Compensated • MECL 10K–Compatible FN SUFFIX PLCC CASE 775–02 LOGIC DIAGRAM MAXIMUM RATINGS Characteristic Symbol Rating Unit VEE VI –8.0 to 0 Vdc 0 to VEE Vdc Power Supply (VCC = 0) Input Voltage (VCC = 0) Output Current — Continuous — Surge Iout 50 100 mA Operating Temperature Range TA Tstg 0 to +75 °C –55 to +150 –55 to +165 °C °C Storage Temperature Range — Plastic — Ceramic ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note) 0° 25° Symbol Min Max Min Max Min Max Unit Power Supply Current IE — 88 — 78 — 88 mA Input Current High Pins 3,5,7,10,12,14 Pins 4,6,9,11,13,15 IinH — — 391 457 — — 246 285 — — 246 285 Input Current Low IinL VOH 0.5 — 0.5 — 0.3 — µA 6 7 9 10 2 11 12 13 14 TRUTH TABLE µA –1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc –1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc High Input Voltage VOL VIH –1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc Low Input Voltage VIL –1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc Low Output Voltage 4 5 15 75° Characteristic High Output Voltage VCC1 = PIN 1 VCC2 = PIN 16 VEE = PIN 8 3 INPUT OUTPUT Sum of High Level Inputs Pin 2 Even Low Odd High DIP PIN ASSIGNMENT AC PARAMETERS VCC1 1 16 VCC2 1.1 3.1 1.1 3.3 1.2 3.5 ns OUT 2 15 IN12 Rise Time tpd tr 0.55 1.5 0.55 1.6 0.75 1.7 ns IN1 3 14 IN11 Fall Time tf 0.55 1.5 0.55 1.6 0.75 1.7 ns IN2 4 13 IN10 IN3 5 12 IN9 IN4 6 11 IN8 IN5 7 10 IN7 VEE 8 9 IN6 Propagation Delay NOTE: Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through a 50–ohm resistor to –2.0 volts. Pin assignment is for Dual–in–Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6–11 of the Motorola MECL Data Book (DL122/D). 3/93 Motorola, Inc. 1996 2–246 REV 5 MC10H160 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 775–02 ISSUE C 0.007 (0.180) M T L–M B Y BRK –N– U N S 0.007 (0.180) M T L–M S S N S D –L– –M– Z W 20 D 1 V 0.010 (0.250) G1 X S T L–M S N S VIEW D–D A 0.007 (0.180) M T L–M S N S R 0.007 (0.180) M T L–M S N S Z C H –T– SEATING PLANE F VIEW S G1 0.010 (0.250) S T L–M S 0.007 (0.180) M T L–M S N S VIEW S S N S NOTES: 1. DATUMS –L–, –M–, AND –N– DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM –T–, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). MECL Data DL122 — Rev 6 N K 0.004 (0.100) J S K1 E G 0.007 (0.180) M T L–M 2–247 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 ––– 0.025 ––– 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 ––– 0.020 2_ 10 _ 0.310 0.330 0.040 ––– MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 ––– 0.64 ––– 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 ––– 0.50 2_ 10 _ 7.88 8.38 1.02 ––– MOTOROLA MC10H160 OUTLINE DIMENSIONS L SUFFIX CERAMIC DIP PACKAGE CASE 620–10 ISSUE V –A– 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. –B– C L DIM A B C D E F G H K L M N –T– K N SEATING PLANE M E F J G D 16 PL 0.25 (0.010) 16 PL 0.25 (0.010) M T A T B M –A– 9 1 8 B F C L S –T– SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 ––– 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01 S P SUFFIX PLASTIC DIP PACKAGE CASE 648–08 ISSUE R 16 S INCHES MIN MAX 0.750 0.785 0.240 0.295 ––– 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 T A M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405; Denver, Colorado 80217. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 2–248 MC10H160/D MECL Data DL122 — Rev 6