MOTOROLA MC68HC908RF2

68HC08M6
HC08M68HC
8M68HC08M
MC68HC908RF2/D
REV 1
MC68HC908RF2
Advance Information
HCMOS
Microcontroller Unit
blank
MC68HC908RF2
Advance Information
Motorola reserves the right to make changes without further notice to any products
herein. Motorola makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Motorola assume any
liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental
damages. "Typical" parameters which may be provided in Motorola data sheets and/or
specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including "Typicals" must be validated for
each customer application by customer’s technical experts. Motorola does not convey
any license under its patent rights nor the rights of others. Motorola products are not
designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Motorola product could create a
situation where personal injury or death may occur. Should Buyer purchase or use
Motorola products for any such unintended or unauthorized application, Buyer shall
indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal
injury or death associated with such unintended or unauthorized use, even if such claim
alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
Motorola and
are registered trademarks of Motorola, Inc.
DigitalDNA is a trademark of Motorola, Inc.
MC68HC908RF2 — Rev. 1
MOTOROLA
© Motorola, Inc., 2001
Advance Information
3
Advance Information
To provide the most up-to-date information, the revision of our
documents on the World Wide Web will be the most current. Your printed
copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://www.motorola.com/mcu/
The following revision history table summarizes changes contained in
this document. For your convenience, the page number designators
have been linked to the appropriate location.
Revision History
Date
Revision
Level
June, 2001
Advance Information
4
Page
Number(s)
Description
First bulleted paragraph under the subsection 15.6 Interrupts
reworded for clarity
208
Revision to the description of the CHxMAX bit and the note that
follows that description
218
17.3 Absolute Maximum Ratings — ESD HBM and ESD MM
entries added
234
17.9 UHF Transmitter Module — Table entries and figures
revised throughout
239
17.12 LVI Characteristics — VLVS and VLVR specifications
updated — low voltage reset and detection entries deleted
247
17.13 Memory Characteristics — Maximum value for FLASH
page program pulses updated
248
1
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information — MC68HC908RF2
List of Sections
Section 1. General Description . . . . . . . . . . . . . . . . . . . . 25
Section 2. Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Section 3. Random-Access Memory (RAM) . . . . . . . . . . 43
Section 4. FLASH 2TS Memory . . . . . . . . . . . . . . . . . . . . 45
Section 5. Central Processor Unit (CPU) . . . . . . . . . . . . 65
Section 6. System Integration Module (SIM) . . . . . . . . . 81
Section 7. Break Module (BRK) . . . . . . . . . . . . . . . . . . . 103
Section 8. Internal Clock Generator Module (ICG). . . . 109
Section 9. Configuration Register (CONFIG) . . . . . . . . 147
Section 10. Monitor Read-Only Memory (MON) . . . . . . 151
Section 11. Computer Operating Properly
Module (COP) . . . . . . . . . . . . . . . . . . . . . . . 163
Section 12. Low-Voltage Inhibit (LVI) . . . . . . . . . . . . . . 169
Section 13. Input/Output (I/O) Ports . . . . . . . . . . . . . . . 175
Section 14. Keyboard/External Interrupt
Module (KBI) . . . . . . . . . . . . . . . . . . . . . . . . 183
Section 15. Timer Interface Module (TIM) . . . . . . . . . . . 197
Section 16. PLL Tuned UHF Transmitter Module . . . . . 221
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
List of Sections
5
List of Sections
Section 17. Preliminary Electrical Specifications . . . . 233
Section 18. Mechanical Specifications . . . . . . . . . . . . . 249
Section 19. Ordering Information . . . . . . . . . . . . . . . . . 251
Advance Information
6
MC68HC908RF2 — Rev. 1
List of Sections
MOTOROLA
Advance Information — MC68HC908RF2
Table of Contents
Section 1. General Description
1.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.4
MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.5
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.5.1
Power Supply Pins (VDD and VSS) . . . . . . . . . . . . . . . . . . . .29
1.5.2
Oscillator Pins (OSC1 and OSC2) . . . . . . . . . . . . . . . . . . . .30
1.5.3
External Reset (RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1.5.4
External Interrupt Pin (IRQ1) . . . . . . . . . . . . . . . . . . . . . . . .30
1.5.5
Port A Input/Output Pins
(PTA7, PTA6/KBD6–PTA1/KBD1, and PTA0) . . . . . . . . 31
1.5.6
Port B Input/Output Pins
(PTB3/TCLK, PTB2/TCH0, PTB1, and PTB0/MCLK) . . . 31
1.5.7
UHF Transmitter Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Section 2. Memory Map
2.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.3
Input/Output Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.4
Monitor ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Table of Contents
7
Table of Contents
Section 3. Random-Access Memory (RAM)
3.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Section 4. FLASH 2TS Memory
4.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.4
FLASH 2TS Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.5
FLASH 2TS Charge Pump Frequency Control. . . . . . . . . . . . . 49
4.6
FLASH 2TS Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.7
FLASH 2TS Program/Margin Read Operation . . . . . . . . . . . . . 50
4.8
FLASH 2TS Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.9
FLASH 2TS Block Protect Register . . . . . . . . . . . . . . . . . . . . . 54
4.10
Embedded Program/Erase Routines . . . . . . . . . . . . . . . . . . . . 55
4.11 Embedded Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . 56
4.11.1 RDVRRNG Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.11.2 PRGRNGE Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.11.3 ERARNGE Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.11.4 REDPROG Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.11.5 Example Routine Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
4.12 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.12.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
4.12.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Advance Information
8
MC68HC908RF2 — Rev. 1
Table of Contents
MOTOROLA
Table of Contents
Section 5. Central Processor Unit (CPU)
5.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4
CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4.1
Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.4.2
Index Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.4.3
Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
5.4.4
Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
5.4.5
Condition Code Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.5
Arithmetic/Logic Unit (ALU) . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5.6
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5.6.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
5.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
5.7
CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 72
5.8
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
5.9
Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Section 6. System Integration Module (SIM)
6.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.3
SIM Bus Clock Control and Generation . . . . . . . . . . . . . . . . . . 85
6.3.1
Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
6.3.2
Clock Startup from POR or LVI Reset . . . . . . . . . . . . . . . . . 85
6.3.3
Clocks in Stop Mode and Wait Mode . . . . . . . . . . . . . . . . . . 86
6.4
Reset and System Initialization. . . . . . . . . . . . . . . . . . . . . . . . . 86
6.4.1
External Pin Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.4.2
Active Resets from Internal Sources . . . . . . . . . . . . . . . . . . 88
6.4.2.1
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.4.2.2
Computer Operating Properly (COP) Reset. . . . . . . . . . . 90
6.4.2.3
Illegal Opcode Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Table of Contents
9
Table of Contents
6.4.2.4
6.4.2.5
Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Low-Voltage Inhibit (LVI) Reset . . . . . . . . . . . . . . . . . . . .90
6.5
SIM Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
6.5.1
SIM Counter During Power-On Reset . . . . . . . . . . . . . . . . . 91
6.5.2
SIM Counter During Stop Mode Recovery . . . . . . . . . . . . . . 91
6.5.3
SIM Counter and Reset States. . . . . . . . . . . . . . . . . . . . . . . 91
6.6
Program Exception Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.6.1
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.6.1.1
Hardware Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
6.6.1.2
SWI Instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.6.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.6.3
Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.6.4
Status Flag Protection in Break Mode . . . . . . . . . . . . . . . . . 96
6.7
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
6.7.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
6.7.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
6.8
SIM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
6.8.1
SIM Break Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . 99
6.8.2
SIM Reset Status Register . . . . . . . . . . . . . . . . . . . . . . . . 100
6.8.3
SIM Break Flag Control Register . . . . . . . . . . . . . . . . . . . . 101
Section 7. Break Module (BRK)
7.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.4
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
7.4.1
Flag Protection During Break Interrupts . . . . . . . . . . . . . . . 105
7.4.2
CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . .105
7.4.3
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . 106
7.4.4
COP During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . .106
7.5
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
7.5.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
7.5.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Advance Information
10
MC68HC908RF2 — Rev. 1
Table of Contents
MOTOROLA
Table of Contents
7.6
Break Module Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
7.6.1
Break Status and Control Register . . . . . . . . . . . . . . . . . . .107
7.6.2
Break Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Section 8. Internal Clock Generator Module (ICG)
8.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
8.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
8.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
8.4
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
8.4.1
Clock Enable Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
8.4.2
Internal Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . 113
8.4.2.1
Digitally Controlled Oscillator . . . . . . . . . . . . . . . . . . . . . 114
8.4.2.2
Modulo N Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
8.4.2.3
Frequency Comparator . . . . . . . . . . . . . . . . . . . . . . . . . 114
8.4.2.4
Digital Loop Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
8.4.3
External Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . 116
8.4.3.1
External Oscillator Amplifier . . . . . . . . . . . . . . . . . . . . . . 116
8.4.3.2
External Clock Input Path . . . . . . . . . . . . . . . . . . . . . . .117
8.4.4
Clock Monitor Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
8.4.4.1
Clock Monitor Reference Generator . . . . . . . . . . . . . . . 118
8.4.4.2
Internal Clock Activity Detector . . . . . . . . . . . . . . . . . . . 121
8.4.4.3
External Clock Activity Detector . . . . . . . . . . . . . . . . . . .121
8.4.5
Clock Selection Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
8.4.5.1
Clock Selection Switch. . . . . . . . . . . . . . . . . . . . . . . . . . 122
8.4.5.2
Clock Switching Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . 123
8.5
Usage Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
8.5.1
Switching Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . 125
8.5.2
Enabling the Clock Monitor . . . . . . . . . . . . . . . . . . . . . . . . 126
8.5.3
Clock Monitor Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
8.5.4
Quantization Error in DCO Output . . . . . . . . . . . . . . . . . . . 127
8.5.4.1
Digitally Controlled Oscillator . . . . . . . . . . . . . . . . . . . . . 128
8.5.4.2
Binary Weighted Divider . . . . . . . . . . . . . . . . . . . . . . . . 128
8.5.4.3
Variable-Delay Ring Oscillator . . . . . . . . . . . . . . . . . . . . 129
8.5.4.4
Ring Oscillator Fine-Adjust Circuit . . . . . . . . . . . . . . . . . 129
8.5.5
Switching Internal Clock Frequencies . . . . . . . . . . . . . . . . 130
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Table of Contents
11
Table of Contents
8.5.6
8.5.6.1
8.5.6.2
8.5.6.3
8.5.7
8.5.8
Nominal Frequency Settling Time . . . . . . . . . . . . . . . . . . . 131
Settling to Within 15 Percent . . . . . . . . . . . . . . . . . . . . . 131
Settling to Within 5 Percent . . . . . . . . . . . . . . . . . . . . . . 132
Total Settling Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Improving Settling Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Trimming Frequency on the Internal Clock Generator . . . . 135
8.6
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
8.6.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
8.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
8.7
Configuration Register Option . . . . . . . . . . . . . . . . . . . . . . . . 137
8.7.1
EXTSLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
8.8
I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
8.8.1
ICG Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
8.8.2
ICG Multiplier Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
8.8.3
ICG Trim Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
8.8.4
ICG DCO Divider Register . . . . . . . . . . . . . . . . . . . . . . . . . 145
8.8.5
ICG DCO Stage Register . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Section 9. Configuration Register (CONFIG)
9.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
9.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
9.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Section 10. Monitor Read-Only Memory (MON)
10.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
10.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
10.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
10.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
10.4.1 Monitor Mode Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
10.4.2 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
10.4.3 Echoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
10.4.4 Break Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Advance Information
12
MC68HC908RF2 — Rev. 1
Table of Contents
MOTOROLA
Table of Contents
10.4.5
10.4.6
10.4.7
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Section 11. Computer Operating Properly
Module (COP)
11.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
11.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
11.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
11.4 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
11.4.1 CGMXCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
11.4.2 STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
11.4.3 COPCTL Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.4.4 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
11.4.5 Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.4.6 Reset Vector Fetch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.4.7 COPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.4.8 COPRS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.5
COP Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
11.6
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
11.7
Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
11.8 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
11.8.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
11.8.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168
11.9
COP Module During Break Interrupts . . . . . . . . . . . . . . . . . . .168
Section 12. Low-Voltage Inhibit (LVI)
12.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
12.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
12.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Table of Contents
13
Table of Contents
12.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
12.4.1 False Trip Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
12.4.2 Short Stop Recovery Option. . . . . . . . . . . . . . . . . . . . . . . . 171
12.5
LVI Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
12.6
LVI Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
12.7 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
12.7.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
12.7.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
Section 13. Input/Output (I/O) Ports
13.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
13.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
13.3 Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
13.3.1 Port A Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
13.3.2 Data Direction Register A. . . . . . . . . . . . . . . . . . . . . . . . . . 178
13.4 Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
13.4.1 Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
13.4.2 Data Direction Register B . . . . . . . . . . . . . . . . . . . . . . . . . 181
Section 14. Keyboard/External Interrupt
Module (KBI)
14.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
14.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
14.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
14.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
14.4.1 External Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
14.4.2 IRQ1 Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
14.4.3 KBI Module During Break Interrupts. . . . . . . . . . . . . . . . . . 189
14.4.4 Keyboard Interrupt Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
14.4.5 Keyboard Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Advance Information
14
MC68HC908RF2 — Rev. 1
Table of Contents
MOTOROLA
Table of Contents
14.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
14.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
14.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
14.6 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
14.6.1 IRQ and Keyboard Status and Control Register . . . . . . . . 193
14.6.2 Keyboard Interrupt Enable Register . . . . . . . . . . . . . . . . . . 195
Section 15. Timer Interface Module (TIM)
15.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
15.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
15.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
15.4
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
15.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
15.5.1 TIM Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
15.5.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
15.5.3 Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
15.5.4 Unbuffered Output Compare . . . . . . . . . . . . . . . . . . . . . . .202
15.5.5 Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . 203
15.5.6 Pulse-Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . 204
15.5.7 Unbuffered PWM Signal Generation . . . . . . . . . . . . . . . . . 205
15.5.8 Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . 206
15.5.9 PWM Initialization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
15.6 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
15.6.1 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
15.6.2 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208
15.6.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
15.7
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 209
15.8 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
15.8.1 TIM Clock Pin (TCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
15.8.2 TIM Channel I/O Pins (TCH0) . . . . . . . . . . . . . . . . . . . . . . 210
15.9 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
15.9.1 TIM Status and Control Register . . . . . . . . . . . . . . . . . . . . 211
15.9.2 TIM Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Table of Contents
15
Table of Contents
15.9.3
15.9.4
15.9.5
TIM Counter Modulo Registers . . . . . . . . . . . . . . . . . . . . . 214
TIM Channel Status and Control Registers . . . . . . . . . . . . 214
TIM Channel Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . .218
Section 16. PLL Tuned UHF Transmitter Module
16.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
16.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
16.3
Transmitter Functional Description . . . . . . . . . . . . . . . . . . . . . 223
16.4
Phase-Lock Loop (PLL) and Local Oscillator . . . . . . . . . . . . . 223
16.5
RF Output Stage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
16.6
Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
16.7
Microcontroller Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
16.8
State Machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
16.9
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .228
16.10 Data Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
16.11 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
16.11.1 Application Schematics in OOK and FSK Modulation . . . .229
16.11.2 Complete Application Schematic . . . . . . . . . . . . . . . . . . . . 232
Section 17. Preliminary Electrical Specifications
17.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
17.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
17.3
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 234
17.4
Functional Operating Range. . . . . . . . . . . . . . . . . . . . . . . . . . 235
17.5
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
17.6
1.8-Volt to 3.3-Volt DC Electrical Characteristics
Excluding UHF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
17.7
3.0-Volt DC Electrical Characteristics
Excluding UHF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Advance Information
16
MC68HC908RF2 — Rev. 1
Table of Contents
MOTOROLA
Table of Contents
17.8
2.0-Volt DC Electrical Characteristics
Excluding UHF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
17.9 UHF Transmitter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
17.9.1 UHF Module Electrical Characteristics. . . . . . . . . . . . . . . . 239
17.9.2 UHF Module Output Power Measurement . . . . . . . . . . . . . 244
17.10 Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
17.11 Internal Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . 246
17.12 LVI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
17.13 Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Section 18. Mechanical Specifications
18.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
18.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
18.3
32-Pin LQFP Package (Case No. 873A) . . . . . . . . . . . . . . . . 250
Section 19. Ordering Information
19.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
19.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
19.3
MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Table of Contents
17
Table of Contents
Advance Information
18
MC68HC908RF2 — Rev. 1
Table of Contents
MOTOROLA
Advance Information — MC68HC908RF2
List of Figures
Figure
Title
1-1
1-2
1-3
MC68HC908RF2 MCU Block Diagram. . . . . . . . . . . . . . . . . . . 28
LQFP Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Power Supply Bypassing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2-1
2-2
Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Control, Status, and Data Registers . . . . . . . . . . . . . . . . . . . . . 36
4-1
4-2
4-3
FLASH 2TS Control Register (FLCR). . . . . . . . . . . . . . . . . . . .47
Smart Programming Algorithm Flowchart. . . . . . . . . . . . . . . . . 52
FLASH 2TS Block Protect Register (FLBPR) . . . . . . . . . . . . . . 54
5-1
5-2
5-3
5-4
5-5
5-6
CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Accumulator (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Index Register (H:X) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Stack Pointer (SP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Program Counter (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Condition Code Register (CCR) . . . . . . . . . . . . . . . . . . . . . . . .69
6-1
6-2
6-3
6-4
6-5
6-6
6-7
6-8
6-9
6-10
6-11
SIM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
SIM I/O Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
ICG Clock Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
External Reset Recovery Timing . . . . . . . . . . . . . . . . . . . . . . . 87
Internal Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Sources of Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
POR Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Interrupt Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Interrupt Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Interrupt Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Interrupt Recognition Example . . . . . . . . . . . . . . . . . . . . . . . . . 95
MC68HC908RF2 — Rev. 1
MOTOROLA
Page
Advance Information
List of Figures
19
List of Figures
Figure
Title
6-12
6-13
6-14
6-15
6-16
6-17
6-18
6-19
Wait Mode Entry Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Wait Recovery from Interrupt or Break . . . . . . . . . . . . . . . . . . . 97
Wait Recovery from Internal Reset. . . . . . . . . . . . . . . . . . . . . . 97
Stop Mode Entry Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Stop Mode Recovery from Interrupt or Break . . . . . . . . . . . . . . 98
SIM Break Status Register (SBSR) . . . . . . . . . . . . . . . . . . . . . 99
SIM Reset Status Register (SRSR) . . . . . . . . . . . . . . . . . . . . 100
SIM Break Flag Control Register (SBFCR) . . . . . . . . . . . . . . 101
7-1
7-2
7-3
7-4
Break Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 104
I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Break Status and Control Register (BSCR) . . . . . . . . . . . . . . 107
Break Address Registers (BRKH and BRKL) . . . . . . . . . . . . . 108
8-1
8-2
8-3
8-4
8-5
8-6
8-7
8-8
8-9
8-10
8-11
8-12
8-13
8-14
8-15
ICG Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Internal Clock Generator Block Diagram . . . . . . . . . . . . . . . . 113
External Clock Generator Block Diagram . . . . . . . . . . . . . . . . 116
Clock Monitor Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 119
Clock Selection Circuit Block Diagram . . . . . . . . . . . . . . . . . . 122
Synchronizing Clock Switcher Circuit Diagram. . . . . . . . . . . . 123
Code Example for Switching Clock Sources . . . . . . . . . . . . . 125
Code Example for Enabling the Clock Monitor . . . . . . . . . . . . 126
Code Example for Writing DDIV and DSTG . . . . . . . . . . . . . .135
ICG I/O Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . 139
ICG Control Register (ICGCR) . . . . . . . . . . . . . . . . . . . . . . . . 141
ICG Multiplier Register (ICGMR) . . . . . . . . . . . . . . . . . . . . . . 143
ICG Trim Register (ICGTR) . . . . . . . . . . . . . . . . . . . . . . . . . . 144
ICG DCO Divider Register (ICGDVR) . . . . . . . . . . . . . . . . . .145
ICG DCO Stage Register (ICGDSR) . . . . . . . . . . . . . . . . . . . 146
9-1
Configuration Register (CONFIG). . . . . . . . . . . . . . . . . . . . . . 148
10-1
10-2
10-3
10-4
Monitor Mode Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Monitor Data Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Sample Monitor Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Read Transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Advance Information
20
Page
MC68HC908RF2 — Rev. 1
List of Figures
MOTOROLA
List of Figures
Figure
Title
Page
10-5
10-6
Break Transaction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Monitor Mode Entry Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . 161
11-1
11-2
COP Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
COP Control Register (COPCTL) . . . . . . . . . . . . . . . . . . . . . . 167
12-1
12-2
LVI Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
LVI Status Register (LVISR) . . . . . . . . . . . . . . . . . . . . . . . . . . 172
13-1
13-2
13-3
13-4
13-5
13-6
13-7
I/O Port Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Port A Data Register (PTA) . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Data Direction Register A (DDRA) . . . . . . . . . . . . . . . . . . . . . 178
Port A I/O Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Port B Data Register (PTB) . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Data Direction Register B (DDRB) . . . . . . . . . . . . . . . . . . . . . 181
Port B I/O Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
14-1
14-2
14-3
14-4
14-5
IRQ Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185
IRQ and Keyboard I/O Register Summary . . . . . . . . . . . . . . . 185
IRQ Interrupt Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Keyboard Interrupt Block Diagram . . . . . . . . . . . . . . . . . . . . . 190
IRQ and Keyboard Status and Control
Register (INTKBSCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Keyboard Interrupt Enable Register (INTKBIER) . . . . . . . . . . 195
14-6
15-1
15-2
15-3
15-4
15-5
15-6
15-7
TIM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200
TIM I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
PWM Period and Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . 204
TIM Status and Control Register (TSC) . . . . . . . . . . . . . . . . . 211
TIM Counter Registers (TCNTH and TCNTL) . . . . . . . . . . . . 213
TIM Counter Modulo Registers (TMODH and TMODL) . . . . . 214
TIM Channel Status and Control Registers
(TSC0 and TSC1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
15-8 CHxMAX Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
15-9 TIM Channel 0 Registers (TCH0H and TCH0L) . . . . . . . . . . . 219
15-10 TIM Channel 1 Registers (TCH1H and TCH1L) . . . . . . . . . . . 219
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
List of Figures
21
List of Figures
Figure
Title
Page
16-1
16-2
16-3
16-4
Simplified Integrated RF Module Block Diagram . . . . . . . . . . 222
Main State Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .226
Signals, Waveforms, and Timing Definitions . . . . . . . . . . . . . 228
Application Schematic in OOK Modulation,
315-MHz and 434-MHz Frequency Bands . . . . . . . . . . . . 229
16-5 Application Schematic in FSK Modulation,
315-MHz and 434-MHz Frequency Bands . . . . . . . . . . . . 230
16-6 Complete Application Schematic in OOK Modulation,
434-MHz Frequency Band. . . . . . . . . . . . . . . . . . . . . . . . . 232
17-1
17-2
17-3
17-4
17-5
17-6
RF Spectrum at 434-MHz Frequency
Band Displayed with a 5-MHz Span . . . . . . . . . . . . . . . . . 242
RF Spectrum at 434-MHz Frequency Band
Displayed with a 50-MHz Span . . . . . . . . . . . . . . . . . . . . . 243
RF Spectrum at 434-MHz Frequency Band
Displayed with a 1.5-GHz Span. . . . . . . . . . . . . . . . . . . . . 243
Output Power Measurement Configurations. . . . . . . . . . . . . .244
Ouput Characteristic and Matching Network
for 434-MHz Frequency Band . . . . . . . . . . . . . . . . . . . . . . 245
Output Power at 434-MHz Frequency Band
versus REXT Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Advance Information
22
MC68HC908RF2 — Rev. 1
List of Figures
MOTOROLA
Advance Information — MC68HC908RF2
List of Tables
Table
Title
1-1
UHF Transmitter Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2-1
Vector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4-1
4-2
4-3
4-4
4-5
Charge Pump Clock Frequency . . . . . . . . . . . . . . . . . . . . . . . .49
Erase Block Sizes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Embedded FLASH Routines. . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Embedded FLASH Routine Global Variables. . . . . . . . . . . . . . 56
CTLBYTE-Erase Block Size . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
5-1
5-2
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6-1
Signal Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
8-1
8-2
8-3
8-4
8-5
Correction Sizes from DLF to DCO . . . . . . . . . . . . . . . . . . . . 115
Clock Monitor Reference Divider Ratios. . . . . . . . . . . . . . . . . 120
Quantization Error in ICLK . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Typical Settling Time Examples . . . . . . . . . . . . . . . . . . . . . . .133
ICG Module Register Bit Interaction Summary. . . . . . . . . . . . 140
10-1
10-2
10-3
10-4
10-5
10-6
10-7
10-8
Monitor Mode Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Mode Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
READ (Read Memory) Command . . . . . . . . . . . . . . . . . . . . . 157
WRITE (Write Memory) Command. . . . . . . . . . . . . . . . . . . . . 158
IREAD (Indexed Read) Command . . . . . . . . . . . . . . . . . . . . . 158
IWRITE (Indexed Write) Command . . . . . . . . . . . . . . . . . . . . 159
READSP (Read Stack Pointer) Command . . . . . . . . . . . . . . . 159
RUN (Run User Program) Command . . . . . . . . . . . . . . . . . . .160
MC68HC908RF2 — Rev. 1
MOTOROLA
Page
Advance Information
List of Tables
23
List of Tables
Table
Title
Page
12-1
LOWV Bit Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
13-1
13-2
Port A Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Port B Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
15-1
15-2
15-3
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Prescaler Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212
Mode, Edge, and Level Selection . . . . . . . . . . . . . . . . . . . . . . 217
16-1
Frequency Band Selection
and Associated Divider Ratios. . . . . . . . . . . . . . . . . . . . . . 223
16-2 DATACLK Frequency
versus Crystal Oscillator Frequency . . . . . . . . . . . . . . . . . 225
16-3 Component Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
16-4 Recommended Crystal Characteristics
(SMD Ceramic Package) . . . . . . . . . . . . . . . . . . . . . . . . . . 231
16-5 Crystal Pulling Capacitor Value
versus Carrier Frequency Total Deviation . . . . . . . . . . . . . 231
19-1
MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251
Advance Information
24
MC68HC908RF2 — Rev. 1
List of Tables
MOTOROLA
Advance Information — MC68HC908RF2
Section 1. General Description
1.1 Contents
1.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.4
MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.5
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.5.1
Power Supply Pins (VDD and VSS) . . . . . . . . . . . . . . . . . . . .29
1.5.2
Oscillator Pins (OSC1 and OSC2) . . . . . . . . . . . . . . . . . . . .30
1.5.3
External Reset (RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1.5.4
External Interrupt Pin (IRQ1) . . . . . . . . . . . . . . . . . . . . . . . .30
1.5.5
Port A Input/Output Pins
(PTA7, PTA6/KBD6–PTA1/KBD1, and PTA0) . . . . . . . . 31
1.5.6
Port B Input/Output Pins (PTB3/TCLK,
PTB2/TCH0, PTB1, and PTB0/MCLK) . . . . . . . . . . . . . . 31
1.5.7
UHF Transmitter Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1.2 Introduction
The MC68HC908RF2 MCU is a member of the low-cost,
high-performance M68HC08 Family of 8-bit microcontroller units
(MCUs). Optimized for low-power operation and available in a small
32-pin low-profile quad flat pack (LQFP), this MCU is well suited for
remote keyless entry (RKE) transmitter designs.
The M68HC08 Family is based on the customer-specified integrated
circuit (CSIC) design strategy. All MCUs in the family use the enhanced
M68HC08 central processor unit (CPU08) and are available with a
variety of modules, memory sizes and types, and package types.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
General Description
25
General Description
1.3 Features
Features of the MC68HC908RF2 MCU include:
•
High-performance M68HC08 architecture
•
Fully upward-compatible object code with M6805, M146805, and
M68HC05 Families
•
Maximum internal bus frequency of 4 MHz at 3.3 volts
•
Maximum internal bus frequency of 2 MHz at 1.8 volts
•
Internal oscillator requiring no external components:
– Software selectable bus frequencies
– ± 25 percent accuracy with trim capability to ±2 percent
– Option to allow use of external clock source or external
crystal/ceramic resonator
•
2 Kbytes of on-chip FLASH memory
•
FLASH program memory security(1)
•
128 bytes of on-chip RAM
•
16-bit, 2-channel timer interface module (TIM)
•
12 general-purpose input/output (I/O) ports:
– Six shared with keyboard wakeup function
– Two shared with the timer module
– Port A pins have 3-mA sink capabilities
•
Low-voltage inhibit (LVI) module:
– 1.85-V detection forces MCU into reset
– 2.0-V detection sets indicator flag
•
6-bit keyboard interrupt with wakeup feature
•
External asynchronous interrupt pin with internal pullup (IRQ1)
•
Ultra high frequency (UHF) transmitter
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
Advance Information
26
MC68HC908RF2 — Rev. 1
General Description
MOTOROLA
General Description
MCU Block Diagram
•
System protection features:
– Computer operating properly (COP) reset
– Low-voltage detection with reset
– Illegal opcode detection with reset
– Illegal address detection with reset
•
32-pin plastic LQFP package
•
Low-power design with stop and wait modes
•
Master reset pin and power-on reset (POR)
•
–40° to 85° Celsius operation
Features of the CPU08 include:
•
Enhanced HC05 programming model
•
Extensive loop control functions
•
16 addressing modes (eight more than the HC05)
•
16-bit index register and stack pointer
•
Memory-to-memory data transfers
•
Fast 8 × 8 multiply instruction
•
Fast 16/8 divide instruction
•
Binary-coded decimal (BCD) instructions
•
Optimization for controller applications
•
Third party C language support
1.4 MCU Block Diagram
Figure 1-1 shows the structure of the MC68HC908RF2 MCU.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
General Description
27
SECURITY
MODULE
CONTROL AND STATUS REGISTERS — 32 BYTES
PTA
ARITHMETIC/LOGIC
UNIT (ALU)
DDRA
CPU
REGISTERS
PTA1/KBD1‡**
PTA0**
DDRB
2-CHANNEL TIMER
MODULE
USER FLASH VECTOR SPACE — 14 BYTES
General Description
OSC2
OSC1
SOFTWARE SELECTABLE
INTERNAL OSCILLATOR
MODULE
VCC
MODE
RST*
SYSTEM INTEGRATION
MODULE
IRQ1*
KEYBOARD/INTERRUPT
MODULE
ENABLE
DATA
BAND
UHF
TRANSMITTER
RFOUT
GNDRF
REXT
POWER-ON RESET
MODULE
XTAL1
XTAL0
DATACLK
MOTOROLA
MC68HC908RF2 — Rev. 1
VDD
CFSK
POWER
VSS
* PIN CONTAINS INTEGRATED PULLUP RESISTOR
** HIGH CURRENT SINK PIN
‡
PIN CONTAINS SOFTWARE SELECTABLE PULLUP RESISTOR
Figure 1-1. MC68HC908RF2 MCU Block Diagram
PTB
LOW-VOLTAGE INHIBIT
MODULE
MONITOR ROM — 768 BYTES
PTA4/KBD4‡**
PTA3/KBD3‡**
PTA2/KBD2‡**
COMPUTER OPERATING PROPERLY
MODULE
USER FLASH — 2031 BYTES
USER RAM — 128 BYTES
PTA7**
PTA6/KBD6‡**
PTA5/KBD5‡ **
PTB3/TCLK
PTB2/TCH0
PTB1
PTB0/MCLK
General Description
Advance Information
28
INTERNAL BUS
M68HC08 CPU
General Description
Pin Assignments
1.5 Pin Assignments
PTA2/KBD
PTA3/KBD
PTA4/KBD
PTA5/KBD
PTA6/KBD
PTA7
RST
IRQ1
32
31
30
29
28
27
26
25
Figure 1-2 shows the pin assignments.
PTB2/TCH0
5
20
PTB3/TCLK
GND
6
19
DATACLK
XTAL1
7
18
DATA
XTAL0
8
17
BAND
16
OSC1
MODE
21
15
4
ENABLE
PTB1
14
OSC2
VCC
22
13
3
GNDRF
PTB0/MCLK
12
VSS
RFOUT
23
11
2
VCC
PTA0
10
VDD
CFSK
24
9
1
REXT
PTA1/KBD1
Figure 1-2. LQFP Pin Assignments
1.5.1 Power Supply Pins (VDD and VSS)
VDD and VSS are the power supply and ground pins. The MCU operates
from a single power supply.
Fast signal transitions on MCU pins place high, short-duration current
demands on the power supply. To prevent noise problems, take special
care to provide power supply bypassing at the MCU as shown in
Figure 1-3. Place the bypass capacitors as close to the MCU power pins
as possible. Use high-frequency-response ceramic capacitors for
CBypass. CBulk are optional bulk current bypass capacitors for use in
applications that require the port pins to source high-current levels.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
General Description
29
General Description
MCU
VDD
VSS
CBypass
0.1 µF
+
CBulk
VDD
Note: Component values shown represent typical applications.
Figure 1-3. Power Supply Bypassing
1.5.2 Oscillator Pins (OSC1 and OSC2)
The OSC1 and OSC2 pins are the connections to an external clock
source or crystal/ceramic resonator.
1.5.3 External Reset (RST)
A logic 0 on the RST pin forces the MCU to a known startup state. RST
is bidirectional, allowing a reset of the entire system. It is driven low when
any internal reset source is asserted.
The RST pin contains an internal pullup resistor.
For additional information, see Section 6. System Integration Module
(SIM).
1.5.4 External Interrupt Pin (IRQ1)
IRQ1 is an asynchronous external interrupt pin.
The IRQ1 pin contains an internal pullup resistor.
Advance Information
30
MC68HC908RF2 — Rev. 1
General Description
MOTOROLA
General Description
Pin Assignments
1.5.5 Port A Input/Output Pins (PTA7, PTA6/KBD6–PTA1/KBD1, and PTA0)
Port A is an 8-bit special function port that shares its pins with the
keyboard interrupt.
Six port A pins (PTA6–PTA1) can be programmed to serve as an
external interrupt. Once enabled, that pin will contain an internal pullup
resistor.
All port A pins are high-current sink pins.
1.5.6 Port B Input/Output Pins (PTB3/TCLK, PTB2/TCH0, PTB1, and PTB0/MCLK)
Port B is a 4-bit, general-purpose, bidirectional I/O port, with some of its
pins shared with the timer (TIM) module.
1.5.7 UHF Transmitter Pins
The MC68HC908RF2 — Rev. 1 uses dedicated pins for its UHF module.
These pins are described in Table 1-1.
Table 1-1. UHF Transmitter Pins
Pin
Function
Description
6
GND
7
XTAL1
Reference oscillator input
8
XTAL0
Reference oscillator output
9
REXT
Output amplifier current setting resistor
10
CFSK
FSK switch output
11
VCC
12
RFOUT
Power amplifier output
13
GNDRF
Power amplifier ground
14
VCC
Power supply
15
ENABLE
Enable input
16
MODE
Modulation type selection input
17
BAND
Frequency band selection
18
DATA
Data input
19
DATACLK
Ground
Power supply
Clock output to the microcontroller
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
General Description
31
General Description
Advance Information
32
MC68HC908RF2 — Rev. 1
General Description
MOTOROLA
Advance Information — MC68HC908RF2
Section 2. Memory Map
2.1 Contents
2.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.3
Input/Output Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.4
Monitor ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
2.2 Introduction
The memory map, shown in Figure 2-1, includes:
•
2031 bytes of user FLASH memory
•
128 bytes of random-access memory (RAM)
•
14 bytes of user-defined vectors in FLASH memory
•
768 bytes of monitor read-only memory (ROM)
These definitions apply to the memory map representation of reserved
and unimplemented locations:
•
Reserved — Accessing a reserved location can have
unpredictable effects on MCU operation.
•
Unimplemented — Accessing an unimplemented location causes
an illegal address reset.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Memory Map
33
Memory Map
$0000
↓
$003F
I/O REGISTERS (28 BYTES)
$0040
↓
$007F
UNIMPLEMENTED (64 BYTES)
$0080
↓
$00FF
RAM (128 Bytes)
$0100
↓
$77FF
UNIMPLEMENTED (30,464 BYTES)
$7800
↓
$7FEE
FLASH MEMORY (2031 BYTES)
$7FEF
OPTIONAL FACTORY DETERMINED ICG TRIM VALUE(1)
$7FF0
↓
$EFFF
UNIMPLEMENTED (28,688 BYTES)
$F000
↓
$F2EF
MONITOR ROM (752 BYTES)
$F2F0
↓
$FDFF
UNIMPLEMENTED (2832 BYTES)
$FE00
SIM BREAK STATUS REGISTER (SBSR)
$FE01
SIM RESET STATUS REGISTER (SRSR)
$FE02
SIM BREAK FLAG CONTROL REGISTER (SBFCR)
$FE03
↓
$FE06
RESERVED (4 BYTES)
$FE07
UNIMPLEMENTED (1 BYTE)
$FE08
FLASH CONTROL REGISTER (FLCR)
$FE09
RESERVED (1 BYTE)
$FE0A
↓
$FE0B
UNIMPLEMENTED (2 BYTES)
$FE0C
BREAK ADDRESS REGISTER HIGH (BRKH)
$FE0D
BREAK ADDRESS REGISTER LOW (BRKL)
1. Address $7FEF is reserved for an optional factory-determined ICG
trim value. Consult with a local Motorola representative for more
information and availability of this option.
Figure 2-1. Memory Map
Advance Information
34
MC68HC908RF2 — Rev. 1
Memory Map
MOTOROLA
Memory Map
Input/Output Section
$FE0E
BREAK STATUS AND CONTROL REGISTER (BSCR)
$FE0F
LVI STATUS REGISTER (LVISR)
$FE10
↓
$FEEF
UNIMPLEMENTED (222 BYTES)
$FEF0
↓
$FEFF
MONITOR ROM (16 BYTES)
$FF00
↓
$FFEF
UNIMPLEMENTED (240 BYTES)
$FFF0
FLASH BLOCK PROTECT REGISTER (FLBPR)
$FFF1
RESERVED (1 BYTE)
$FFF2
↓
$FFFF
FLASH VECTORS
(14 Bytes)
Figure 2-1. Memory Map (Continued)
2.3 Input/Output Section
Addresses $0000–$003F, shown in Figure 2-2, contain most of the
control, status, and data registers. Additional I/O registers have these
addresses:
•
$FE00 — SIM break status register, SBSR
•
$FE01 — SIM reset status register, SRSR
•
$FE02 — SIM break flag control register, BFCR
•
$FE08 — FLASH control register, FLCR
•
$FE0C — BREAK address register high, BRKH
•
$FE0D — BREAK address register low, BRKL
•
$FE0E — BREAK status and control register, BSCR
•
$FE0F — LVI status register, LVISR
•
$FFF0 — FLASH block protection register, FLBPR
•
$FFFF — COP control register, COPCTL
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Memory Map
35
Memory Map
Addr.
$0000
$0001
Register Name
Read:
Port A Data Register
(PTA) Write:
See page 177.
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
PTB2
PTB1
PTB0
Unaffected by reset
Read:
Port B Data Register
(PTB) Write:
See page 180.
Reset:
$0002
Unimplemented
$0003
Unimplemented
PTB3
Unaffected by reset
Read:
Data Direction Register A
DDRA7
$0004
(DDRA) Write:
See page 178.
Reset:
0
Read:
Data Direction Register B
MCLKEN
$0005
(DDRB) Write:
See page 181.
Reset:
0
$0006
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
KEYF
0
IMASKK
MODEK
R
ACKK
0
0
0
0
0
IMASKI
MODEI
Unimplemented
↓
$0019
Unimplemented
IRQ and Keyboard Status Read:
and Control Register
Write:
$001A
(INTKBSCR)
See page 193. Reset:
IRQ1F
Read:
Keyboard Interrupt Enable
$001B
Register (INTKBIER) Write:
See page 196.
Reset:
0
0
R
ACKI
0
0
0
0
0
0
0
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
0
0
0
0
0
0
= Unimplemented
R
0
0
0
= Reserved U = Unaffected X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 1 of 6)
Advance Information
36
MC68HC908RF2 — Rev. 1
Memory Map
MOTOROLA
Memory Map
Input/Output Section
Addr.
Register Name
$001C
Bit 7
6
5
4
3
2
1
Bit 0
LVIRST
LVIPWR
COPRS
SSREC
STOP
COPD
1
1
0
0
0
0
0
0
PS2
PS1
PS0
Unimplemented
↓
$001E
$001F
Unimplemented
Read:
Configuration Register
EXTSLOW LVISTOP
(CONFIG) Write:
See page 148.
Reset:
0
0
Read:
Timer Status and Control
$0020
Register (TSC) Write:
See page 213.
Reset:
TOF
0
0
1
0
0
0
0
0
Read:
Timer Counter Register
High (TCNTH) Write:
See page 215.
Reset:
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Read:
Timer Counter Register
Low (TCNTL) Write:
See page 215.
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
6
5
4
3
2
1
Bit 0
1
1
1
1
1
1
1
1
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
= Unimplemented
R
$0021
$0022
$0023
Read:
Timer Counter Modulo
Register High (TMODH) Write:
See page 216.
Reset:
Timer Counter Read:
Modulo Register Low
$0024
Write:
(TMODL)
See page 216. Reset:
$0025
Read:
Timer Channel 0 Status
and Control Register Write:
(TSC0) See page 217.
Reset:
TOIE
TSTOP
0
TRST
CH0F
0
0
= Reserved U = Unaffected X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 2 of 6)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Memory Map
37
Memory Map
Addr.
Register Name
Read:
Timer Channel 0 Register
$0026
High (TCH0H) Write:
See page 221.
Reset:
Read:
Timer Channel 0 Register
$0027
Low (TCH0L) Write:
See page 221.
Reset:
$0028
Read:
Timer Channel 1 Status
and Control Register Write:
(TSC1) See page 217.
Reset:
Read:
Timer Channel 1 Register
$0029
High (TCH1H) Write:
See page 221.
Reset:
Read:
Timer Channel 1 Register
$002A
Low (TCH1L) Write:
See page 221.
Reset:
$002B
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
CH1F
0
CH1IE
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
Unimplemented
↓
$0035
Unimplemented
$0036
Read:
Internal Clock Generator
Control Register Write:
(ICGCR) See page 141.
Reset:
$0037
Read:
Internal Clock Generator
Multiplier Register Write:
(ICGMR) See page 143.
Reset:
CMF
CMIE
ICGS
CMON
CS
ICGON
ECGS
ECGON
0
0
0
0
1
0
0
0
R
N6
N5
N4
N3
N2
N1
N0
0
0
0
1
0
1
0
1
= Unimplemented
R
= Reserved U = Unaffected X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 3 of 6)
Advance Information
38
MC68HC908RF2 — Rev. 1
Memory Map
MOTOROLA
Memory Map
Input/Output Section
Addr.
$0038
Register Name
Read:
Internal Clock Generator
Trim Register (ICGTR) Write:
See page 144.
Reset:
ICG DCO Divider Read:
Control Register
$0039
(ICGDVR)
Bit 7
6
5
4
3
2
1
Bit 0
TRIM7
TRIM6
TRIM5
TRIM4
TRIM3
TRIM2
TRIM1
TRIM0
1
0
0
0
0
0
0
0
R
R
R
R
DDIV3
DDIV2
DDIV1
DDIV0
0
0
0
0
U
U
U
U
DSTG6
DSTG5
DSTG4
DSTG3
DSTG2
DSTG1
DSTG0
R
R
Write:
See page 145. Reset:
Read:
ICG DCO Stage Register
DSTG7
$003A
(ICGDSR) Write:
See page 146.
Reset:
$003B
Reserved
$003C
Unimplemented
↓
$003F
Unimplemented
Read:
SIM Break Status Register
$FE00
(SBSR) Write:
See page 99.
Reset:
Unaffected by reset
R
R
R
R
R
R
R
R
R
R
R
R
SBSW
R
See Note
0
Note: Writing a logic 0 clears SBSW
Read:
SIM Reset Status Register
$FE01
(SRSR) Write:
See page 100.
POR:
$FE02
Read:
SIM Break Flag Control
Register (SBFCR) Write:
See page 101.
Reset:
$FE03
Reserved
POR
PIN
COP
ILOP
ILAD
0
LVI
0
1
X
X
X
X
X
X
X
BCFE
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
R
R
R
R
R
R
R
R
= Unimplemented
R
= Reserved U = Unaffected X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 4 of 6)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Memory Map
39
Memory Map
Addr.
Register Name
$FE04
Reserved
$FE05
Unimplemented
Bit 7
6
5
4
3
2
1
Bit 0
R
R
R
R
R
R
R
R
FDIV0
BLK1
BLK0
HVEN
MARGIN
ERASE
PGM
0
0
0
0
0
0
0
0
R
R
R
R
R
R
R
R
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BRKE
BRKA
0
0
0
0
0
0
0
0
0
LOWV
0
0
0
0
0
0
0
0
0
0
0
0
= Unimplemented
R
↓
$FE07
$FE08
Unimplemented
Read:
FLASH 2TS Control
Register (FLCR) Write:
See page 47.
Reset:
$FE09
Reserved
$FE0A
Unimplemented
$FE0B
Unimplemented
$FE0C
Read:
Break Address Register
High (BRKH) Write:
See page 108.
Reset:
$FE0D
Read:
Break Address Register
Low (BRKL) Write:
See page 108.
Reset:
Read:
Break Status and Control
$FE0E
Register (BSCR) Write:
See page 107.
Reset:
$FE0F
0
Read: LVIOUT
LVI Status Register
(LVISR) Write:
See page 172.
Reset:
0
= Reserved U = Unaffected X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 5 of 6)
Advance Information
40
MC68HC908RF2 — Rev. 1
Memory Map
MOTOROLA
Memory Map
Input/Output Section
Addr.
Register Name
FLASH 2TS Block Protect Read:
Register (FLBPR)†
$FFF0
Write:
See page 54.
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
R
R
R
R
BPR3
BPR2
BPR1
BPR0
Unaffected by reset
† Non-volatile FLASH register
$FFFF
Read:
COP Control Register
(COPCTL) Write:
See page 167.
Reset:
Low byte of reset vector
Writing clears COP counter (any value)
Unaffected by reset
= Unimplemented
R
= Reserved U = Unaffected X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 6 of 6)
Table 2-1 is a list of vector locations.
Table 2-1. Vector Locations
High
Priority
Low
Address
Vector
$FFF2
ICG vector (high)
$FFF3
ICG vector (low)
$FFF4
TIM overflow vector (high)
$FFF5
TIM overflow vector (low)
$FFF6
TIM channel 1 vector (high)
$FFF7
TIM channel 1 vector (low)
$FFF8
TIM channel 0 vector (high)
$FFF9
TIM channel 0 vector (low)
$FFFA
IRQ1/keyboard vector (high)
$FFFB
IRQ1/keyboard vector (low)
$FFFC
SWI vector (high)
$FFFD
SWI vector (low)
$FFFE
Reset vector (high)
$FFFF
Reset vector (low)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Memory Map
41
Memory Map
2.4 Monitor ROM
The 768 bytes at addresses $F000–F2EF and $FEF0–$FEFF are
utilized by the monitor ROM.
The address range $F000–F2EF is reserved for the monitor code
functions, FLASH memory programming, and erase algorithms.
The address range $FEF0–$FEFF holds reserved ROM addresses that
contain the monitor code reset vectors.
Advance Information
42
MC68HC908RF2 — Rev. 1
Memory Map
MOTOROLA
Advance Information — MC68HC908RF2
Section 3. Random-Access Memory (RAM)
3.1 Contents
3.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.2 Introduction
This section describes the 128 bytes of random-access memory (RAM).
3.3 Functional Description
Addresses $0080–$00FF are RAM locations. The location of the stack
RAM is programmable.
NOTE:
For correct operation, the stack pointer must point only to RAM
locations.
Before processing an interrupt, the CPU uses five bytes of the stack to
save the contents of the CPU registers.
NOTE:
For M68HC05, M6805, and M146805 compatibility, the H register is not
stacked.
During a subroutine call, the CPU uses two bytes of the stack to store
the return address. The stack pointer decrements during pushes and
increments during pulls.
NOTE:
Be careful when using nested subroutines. The CPU could overwrite
data in the RAM during a subroutine or during the interrupt stacking
operation.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Random-Access Memory (RAM)
43
Random-Access Memory (RAM)
Advance Information
44
MC68HC908RF2 — Rev. 1
Random-Access Memory (RAM)
MOTOROLA
Advance Information — MC68HC908RF2
Section 4. FLASH 2TS Memory
4.1 Contents
4.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.4
FLASH 2TS Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.5
FLASH 2TS Charge Pump Frequency Control. . . . . . . . . . . . . 49
4.6
FLASH 2TS Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.7
FLASH 2TS Program/Margin Read Operation . . . . . . . . . . . . . 50
4.8
FLASH 2TS Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.9
FLASH 2TS Block Protect Register . . . . . . . . . . . . . . . . . . . . . 54
4.10
Embedded Program/Erase Routines . . . . . . . . . . . . . . . . . . . . 55
4.11 Embedded Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . 56
4.11.1 RDVRRNG Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.11.2 PRGRNGE Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.11.3 ERARNGE Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.11.4 REDPROG Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.11.5 Example Routine Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
4.12 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.12.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
4.12.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
4.2 Introduction
This section describes the operation of the embedded FLASH 2TS
memory. This memory can be read, programmed, and erased from a
single external supply. The program and erase operations are enabled
through the use of an internal charge pump.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
45
FLASH 2TS Memory
4.3 Functional Description
The FLASH 2TS memory is appropriately named to describe its
2-transistor source-select bit cell. The FLASH 2TS memory is an array
of 2031 bytes with an additional 14 bytes of user vectors and one byte
for block protection. An erased bit reads as a logic 0 and a programmed
bit reads as a logic 1.
The address ranges for the user memory, control register, and vectors
are:
•
$7800–$7FEE, user space
•
$7FEF, reserved — optional ICG trim value, see 8.8.3 ICG Trim
Register
•
$FFF0, block protect register
•
$FE08, FLASH 2TS control register
•
$FFF2–$FFFF, these locations are reserved for user-defined
interrupt and reset vectors
This list is the row architecture for the user space array:
$7800–$7807 (Row 0)
$7808–$780F (Row 1)
$7810–$7817 (Row 2)
$7818–$781F (Row 3)
$7820–$7827 (Row 4)
-------------------------$7FE8–$7FEF (Row 253)
Program and erase operations are facilitated through control bits in a
memory mapped register. Details for these operations appear later in
this section. Memory in the FLASH 2TS array is organized into pages
within rows. For the 2-Kbyte array on the MC68HC908RF2, the page
size is one byte. There are eight pages (or eight bytes) per row.
Programming operations are performed on a page basis, one byte at a
time. Erase operations are performed on a block basis. The minimum
Advance Information
46
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
FLASH 2TS Control Register
block size is one row of eight bytes. Refer to Table 4-2 for additional
block size options.
NOTE:
Sometimes a program disturb condition, in which case an erased bit on
the row being programmed unintentionally becomes programmed,
occurs. The embedded smart programming algorithm implements a
margin read technique to avoid program disturb. The margin read step
of the smart programming algorithm is used to ensure programmed bits
are programmed to sufficient margin for data retention over the device’s
lifetime. In the application code, perform an erase operation after eight
program operations (on the same row) to further avoid program disturb.
For availability of programming tools and more information, contact a
local Motorola representative.
NOTE:
A security feature prevents viewing of the FLASH 2TS contents.(1)
4.4 FLASH 2TS Control Register
The FLASH 2TS control register (FLCR) controls program, erase, and
margin read operations.
Address:
$FE08
Bit 7
Read:
6
5
4
3
2
1
Bit 0
FDIV0
BLK1
BLK0
HVEN
MARGIN
ERASE
PGM
0
0
0
0
0
0
0
0
Write:
Reset:
0
= Unimplemented
Figure 4-1. FLASH 2TS Control Register (FLCR)
FDIV0 — Frequency Divide Control Bit
This read/write bit selects the factor by which the charge pump clock
is divided from the system clock. See 4.5 FLASH 2TS Charge Pump
Frequency Control.
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH 2TS difficult for unauthorized users.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
47
FLASH 2TS Memory
BLK1 — Block Erase Control Bit
This read/write bit together with BLK0 allows erasing of blocks of
varying size. See 4.6 FLASH 2TS Erase Operation for a description
of available block sizes.
BLK0 — Block Erase Control Bit
This read/write bit together with BLK1 allows erasing of blocks of
varying size. See 4.6 FLASH 2TS Erase Operation for a description
of available block sizes.
HVEN — High-Voltage Enable Bit
This read/write bit enables the charge pump to drive high voltages for
program and erase operations in the array. HVEN can be set only if
either PGM = 1 or ERASE = 1 and the proper sequence for smart
programming or erase is followed.
1 = High voltage enabled to array and charge pump on
0 = High voltage disabled to array and charge pump off
MARGIN — Margin Read Control Bit
This read/write bit configures the memory for margin read operation.
MARGIN cannot be set if the HVEN = 1. MARGIN will automatically
return to unset (0) if asserted when HVEN = 1.
1 = Margin read operation selected
0 = Margin read operation unselected
ERASE — Erase Control Bit
This read/write bit configures the memory for erase operation.
ERASE is interlocked with the PGM bit such that both bits cannot be
set at the same time.
1 = Erase operation selected
0 = Erase operation unselected
PGM — Program Control Bit
This read/write bit configures the memory for program operation.
PGM is interlocked with the ERASE bit such that both bits cannot be
set at the same time.
1 = Program operation selected
0 = Program operation unselected
Advance Information
48
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
FLASH 2TS Charge Pump Frequency Control
4.5 FLASH 2TS Charge Pump Frequency Control
The internal charge pump, required for program, margin read, and erase
operations, is designed to operate most efficiently with a 2-MHz clock.
The charge pump clock is derived from the bus clock. Table 4-1 shows
how the FDIV bits are used to select a charge pump frequency based on
the bus clock frequency. Program, margin read, and erase operations
cannot be performed if the bus clock frequency is below 2 MHz.
Table 4-1. Charge Pump Clock Frequency
NOTE:
FDIV0
Pump Clock Frequency
0
Bus frequency ÷ 1
1
Bus frequency ÷ 2
The charge pump is optimized for 2-MHz operation.
4.6 FLASH 2TS Erase Operation
Use this step-by-step procedure to erase a block of FLASH 2TS
memory. Refer to 17.13 Memory Characteristics for a detailed
description of the times used in this algorithm.
1. Set the ERASE, BLK0, BLK1, and FDIV0 bits in the FLASH 2TS
control register. Refer to Table 4-1 for FDIV settings and to
Table 4-2 for block sizes.
2. Ensure target portion of array is unprotected by reading the block
protect register at address $FFF0. Refer to 4.8 FLASH 2TS Block
Protection and 4.9 FLASH 2TS Block Protect Register for more
information.
3. Write to any FLASH 2TS address with any data within the block
address range desired.
4. Set the HVEN bit.
5. Wait for a time, tErase.
6. Clear the HVEN bit.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
49
FLASH 2TS Memory
7. Wait for a time, tKill, for the high voltages to dissipate.
8. Clear the ERASE bit.
9. After a time, tHVD, the memory can be accessed in read mode
again.
NOTE:
While these operations must be performed in the order shown, other
unrelated operations may occur between the steps.
Table 4-2 shows the various block sizes which can be erased in one
erase operation.
Table 4-2. Erase Block Sizes
BLK1
BLK0
Block Size, Addresses Cared
0
0
Full array: 2 Kbytes
0
1
One-half array: 1 Kbyte
1
0
Eight rows: 64 bytes
1
1
Single row: 8 bytes
In step 3 of the erase operation, the cared addresses are latched and
used to determine the location of the block to be erased. For instance,
with BLK0 = BLK1 = 0, writing to any FLASH 2TS address in the range
$7800 to $78F0 will enable the erase of all FLASH memory.
4.7 FLASH 2TS Program/Margin Read Operation
NOTE:
After a total of eight program operations have been applied to a row, the
row must be erased before further programming to avoid program
disturb. An erased byte will read $00.
The FLASH 2TS memory is programmed on a page basis. A page
consists of one byte. The smart programming algorithm (Figure 4-2) is
recommended to program every page in the FLASH 2TS memory.
Advance Information
50
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
FLASH 2TS Program/Margin Read Operation
The embedded smart programming algorithm uses this step-by-step
sequence to program the data into the FLASH memory. The algorithm
optimizes the time required to program each page. Refer to 4.10
Embedded Program/Erase Routines for information on utilizing
embedded routines.
1. Set the FDIV bits. These bits determine the charge pump
frequency.
2. Set PGM = 1. This configures the memory for program operation
and enables the latching of address and data for programming.
3. Read the FLASH 2TS block protect register (FLBPR).
4. Write data to the one byte being programmed.
5. Set HVEN = 1.
6. Wait for a time, tStep.
7. Set HVEN = 0.
8. Wait for a time, tHVTV.
9. Set MARGIN = 1.
10. Wait for a time, tVTP.
11. Set PGM = 0.
12. Wait for a time, tHVD.
13. Read back data in margin read mode. This read operation is
stretched by eight cycles.
14. Clear the MARGIN bit. If the margin read data is identical to
write data, the program operation is complete; otherwise, jump to
step 2.
NOTE:
While these operations must be performed in the order shown, other
unrelated operations may occur between the steps.
The smart programming algorithm guarantees the minimum possible
program time.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
51
FLASH 2TS Memory
PROGRAM FLASH 2TS
Page Program/Margin Read Procedure
Note: This algorithm is mandatory for
programming the FLASH 2TS.
SET INTERRUPT MASK:
SEI INSTRUCTION
Note: This page program algorithm
assumes the page/s to be programmed
are initially erased.
INITIALIZE ATTEMPT COUNTER
TO 0
SET PGM BIT AND FDIV BITS
READ FLASH BLOCK PROTECT REG.
WRITE DATA TO
SELECTED PAGE
SET HVEN BIT
WAIT tSTEP
CLEAR HVEN BIT
WAIT tHVTV
SET MARGIN BIT
WAIT tVTP
CLEAR PGM BIT
WAIT tHVD
MARGIN READ PAGE OF DATA
CLEAR MARGIN BIT
INCREMENT ATTEMPT COUNTER
N
MARGIN READ DATA
EQUAL TO
WRITE DATA?
Y
N
CLEAR MARGIN BIT
ATTEMPT COUNT
EQUAL TO
flsPulses?
CLEAR INTERRUPT MASK:
CLI INSTRUCTION
Y
PROGRAMMING OPERATION
FAILED
PROGRAMMING OPERATION
COMPLETE
Figure 4-2. Smart Programming Algorithm Flowchart
Advance Information
52
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
FLASH 2TS Block Protection
4.8 FLASH 2TS Block Protection
NOTE:
In performing a program or erase operation, the FLASH 2TS block
protect register must be read after setting the PGM or ERASE bit and
before asserting the HVEN bit.
Due to the ability of the on-board charge pump to erase and program the
FLASH 2TS memory in the target application, provision is made for
protecting blocks of memory from unintentional erase or program
operations due to system malfunction. This protection is implemented by
a reserved location in the memory for block protect information. This
block protect register must be read before setting HVEN = 1. When the
block protect register is read, its contents are latched by the FLASH 2TS
control logic. If the address range for an erase or program operation
includes a protected block, the PGM or ERASE bit is cleared which
prevents the HVEN bit in the FLASH 2TS control register from being set
such that no high-voltage operation is allowed in the array.
When the block protect register is erased (all 0s), the entire memory is
accessible for program and erase. When bits within the register are
programmed, they lock blocks of memory address ranges as shown in
4.9 FLASH 2TS Block Protect Register. The block protect register
itself can be erased or programmed only with an external voltage VHI
present on the IRQ1 pin. The presence of VHI on the IRQ1 pin also
allows entry into monitor mode out of reset. Therefore, the ability to
change the block protect register is voltage-level dependent and can
occur in either user or monitor modes.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
53
FLASH 2TS Memory
4.9 FLASH 2TS Block Protect Register
The block protect register (FLBPR) is implemented as a byte within the
FLASH 2TS memory. Each bit, when programmed, protects a range of
addresses in the FLASH 2TS.
Address:
$FFF0
Bit 7
6
5
4
3
2
1
Bit 0
R
R
R
R
BPR3
BPR2
BPR1
BPR0
Read:
Write:
Reset:
Unaffected by reset
R
= Reserved
Figure 4-3. FLASH 2TS Block Protect Register (FLBPR)
BPR3 — Block Protect Register Bit 3
This bit protects the memory contents in the address ranges
$7A00–$7FEF and $FFF0–$FFFF.
1 = Address range protected from erase or program
0 = Address range open to erase or program
BPR2 — Block Protect Register Bit 2
This bit protects the memory contents in the address ranges
$7900–$7FEF and $FFF0–$FFFF.
1 = Address range protected from erase or program
0 = Address range open to erase or program
BPR1 — Block Protect Register Bit 1
This bit protects the memory contents in the address ranges
$7880–$7FEF and $FFF0–$FFFF.
1 = Address range protected from erase or program
0 = Address range open to erase or program
BPR0 — Block Protect Register Bit 0
This bit protects the FLASH memory contents in the address ranges
$7800–$7FEF and $FFF0–$FFFF.
1 = Address range protected from erase or program
0 = Address range open to erase or program
Advance Information
54
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
Embedded Program/Erase Routines
By programming the block protect bits, a portion of the memory will be
locked so that no further erase or program operations may be
performed. Programming more than one bit at a time is redundant. If
both bit 1 and bit 2 are set, for instance, the FLASH address ranges
between $7880–$FFFF are locked. If all bits are erased, then all of the
memory is available for erase and program.
The presence of a voltage VHI on the IRQ1 pin will bypass the block
protection so that all of memory, including the block protect register, can
be programmed or erased.
4.10 Embedded Program/Erase Routines
The MC68HC908RF2 monitor ROM contains numerous routines for
programming and erasing the FLASH memory. These embedded
routines are intended to assist the programmer with modifying the
FLASH memory array. These routines will implement the smart
programming algorithm as defined in Figure 4-2. The functions are listed
in Table 4-3.
Table 4-3. Embedded FLASH Routines
Call
JSR to Address(1)
Read/verify a range
RDVRRNG
ROMSTRT + 0
Program range of FLASH
PRGRNGE
ROMSTRT + 3
Erase range of FLASH
ERARNGE
ROMSTRT + 6
Redundant program FLASH
REDPROG
ROMSTRT + 9
Function Description
1. ROMSTRT is defined as the starting address of the monitor ROM in the memory map. This
is address $F000.
The functions shown in Table 4-3 accept data through the CPU registers
and global variables in RAM. Table 4-4 shows the RAM locations that
are used for passing parameters.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
55
FLASH 2TS Memory
Table 4-4. Embedded FLASH Routine Global Variables
Variable Location
Variable Address(1)
CTRLBYT
RAMSTART + 8
CPUSPD
RAMSTART + 9
LADDR
RAMSTART + 10
BUMPS
RAMSTART + 12
DERASE
RAMSTART + 13
DATA
RAMSTART + 15
1. RAMSTART is defined as the starting address of the RAM in the memory map.
This is address $0080.
4.11 Embedded Function Descriptions
This subsection describes the embedded functions.
4.11.1 RDVRRNG Routine
Name:
Purpose:
Entry conditions:
Exit conditions:
RDVRRNG
Read and/or verify a range of FLASH memory
H:X
Contains the first address of the range
LADDR
Contains the last address of the range
DATA
Contains the data to compare the read data against for
read/verify to RAM only (length is user determined)
ACC
Non-zero for read/verify to RAM, 0 for output to PA0
C bit
Set if good compare for read/verify to RAM only
ACC
Contains checksum
DATA
Contains read FLASH data for read/verify to RAM only
Advance Information
56
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
Embedded Function Descriptions
Ready/verify
RAM option:
Output to PA0
option:
NOTE:
This subroutine both compares data passed in the DATA array to the
FLASH data and reads the data from FLASH into the DATA array. It also
calculates the checksum of the data.
This subroutine dumps the data from the range to PA0 in the same
format as monitor data. It also calculates the checksum of the data.
This serial dump does not circumvent security because the security
vectors must still be passed to make FLASH readable in monitor mode.
4.11.2 PRGRNGE Routine
Name:
Purpose:
Entry conditions:
Exit conditions:
PRGRNGE
Programs a range of addresses in FLASH memory
H:X
Contains the first address in the range
LADDR
Contains the last address in the range
DATA
Contains the data to be programmed (length is user
determined)
CPUSPD
Contains the bus frequency times 4 in MHz
BUMPS
Contains the maximum allowable number of programming
bumps to use
C bit
Set if successful program; cleared otherwise
I bit
Set, masking interrupts
This routine programs a range of FLASH defined by H:X and LADDR.
The range can be from one byte to as much RAM as can be allocated to
DATA. The smart programming algorithm defined in 4.7 FLASH 2TS
Program/Margin Read Operation is used.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
57
FLASH 2TS Memory
4.11.3 ERARNGE Routine
Name:
Purpose:
Entry conditions:
ERARNGE
Erase a range of addresses in FLASH memory
H:X
Contains an address in the range to be erased; range size
specified by control byte
CTLBYTE Contains the erase block size in bits 5 and 6 (see Table 4-5)
DERASE
Contains the erase delay time in µs/24
CPUSPD
CPU frequency times 4 in MHz
Table 4-5. CTLBYTE-Erase Block Size
Exit conditions:
I bit
Bit 6
Bit 5
Block Size
0
0
Full array
0
1
One half array
1
0
Eight rows: 64 pages
1
1
Single row: 8 pages
Set, masking interrupts.
This routine erases the block of FLASH defined by H:X and CTLBYTE.
The algorithm defined in 4.6 FLASH 2TS Erase Operation is used.
Preserves the contents of H:X (address passed)
Advance Information
58
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
Embedded Function Descriptions
4.11.4 REDPROG Routine
Name:
Purpose:
Entry conditions:
Exit conditions:
REDPROG
This routine will use a range of multiple rows in the FLASH array to
emulate increased write/erase cycling capability of one row.
H:X
Contains the address of the first row in the range. This
address must be the first address of a row (multiple of eight
bytes)
LADDR
Address of last row in the range; must be the first address
of a row (multiple of eight bytes)
DATA
Data to program in the row (bit 7 of DATA + 0 is used
internally and will be overwritten). Routine will always use
eight bytes starting at DATA.
BUMPS
Contains the maximum allowable number of programming
bumps to use
CPUSPD
Contains the bus frequency times 4 in MHz
DERASE
Contains the erase delay time in µs/24
C bit
Set if successful program; cleared otherwise
I bit
Set, masking interrupts
This routine uses a range of the FLASH array containing multiple rows
to emulate increased write/erase cycling capability for data storage. The
routine will write data to each row of the FLASH array (in the range
defined) upon subsequent calls. The number of rows is the difference
between the value in H:X and LADDR, divided by 8.
A row is the minimum range that can be programmed with the
REDPROG routine. All rows in the range will be programmed once
before any are programmed again. This approach is taken to ensure that
all rows reach the end of lifetime at approximately the same time.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
59
FLASH 2TS Memory
A special bit will be maintained by the routine, called a cycling bit, in each
row. This bit is used to ensure that the data is programmed to all the rows
defined in the range. This is the high bit of the first byte in each row. This
bit cannot be used to store user data. It will be modified by the
REDPROG routine. This is at bit 7 of the byte at address DATA+0.
To determine which row to program, the algorithm will step from the first
to the last row in a range looking for the first row whose cycling bit is
different from the first. If all rows contain the same cycling bit, then the
first row will be used.
The row whose cycling bit is different will be erased and the entire row
will be programmed with the given data, including a toggled version of
the cycling bit.
4.11.5 Example Routine Calls
This code is for illustrative purposes only and does not represent valid
syntax for any particular assembler.
RAM
EQU
$80
RDVRRNG
EQU
$F000
PRGRNGE
EQU
$F003
ERANRGE
EQU
$F006
REDPROG
EQU
$F009
;*************************************************************
RAM Definitions for Subroutines
;**************************************************************
ORG
CTRLBYT
CPUSPD
LADDR
BUMPS
DERASE
RAM+8
RMB
RMB
RMB
RMB
RMB
1
1
2
1
2
;Allocation of “DATA” space is dependent on the device and
;application
Advance Information
60
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
Embedded Function Descriptions
DATA
RMB
8
;*************************************************************
; CALLING EXAMPLE FOR READ/VERIFY A RANGE (RDVRRNG)
;**************************************************************
LDA
#$FF
;TARGET IS RAM
LDHX
#$7807
;END AFTER FIRST ROW
STHX
LADDR
LDHX
#$7800
;START AT FIRST ROW
JSR
RDVRRNG
;DATA WILL CONTAIN FLASH INFO
;*************************************************************;
CALLING EXAMPLE FOR ERASE A RANGE (ERARNGE)
;**************************************************************
MOV
#$08,CPUSPD
;Load Bus frequency in MHz * 4
MOV
#$60,CTRLBYT
;Bits 5&6 hold the block size to erase
;00 Full Array
;20 One-Half Array
;40 Eight Rows
;60 Singe Row
;Remember a Row is 1 byte
;Set erase time in uS/24, number in
;decimal
LDHX
STHX
LDHX
JSR
#100000/24
DERASE
#$7800
ERARNGE
;Address in the range to erase
;Call through jump table
;************************************************************;
; CALLING EXAMPLE FOR PROGRAM A RANGE (PRGRNGE)
;*************************************************************
MOV
#’P’,DATA
MOV
#’R’,DATA+1
MOV
#’O’,DATA+2
MOV
#’G’,DATA+3
MOV
#’T’,DATA+4
MOV
#’E’,DATA+5
MOV
#’S’,DATA+6
MOV
#’T’,DATA+7
MOV
MOV
#$08,CPUSPD
#$0A,BUMPS
LDHX
STHX
LDHX
#$7807
LADDR
#$7800
JSR
PRGRNGE
;Load Bus frequency in MHz * 4
;Load max number of programming steps
;before a failure is returned
;Load the last address to program
;into LADDR
;Load the first address to program
;into H:X
;This range may cross page boundaries
;and may be any length, so long as the
;data to program is loaded in RAM
;beginning at DATA.
;Call through jump table.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
61
FLASH 2TS Memory
;**************************************************************
; CALLING EXAMPLE FOR REDUNDANT PROGRAM A ROW (REDPROG)
;**************************************************************
MOV
#$56,DATA
MOV
#’P’,DATA+1
MOV
#’R’,DATA+2
MOV
#’O’,DATA+3
MOV
#’G’,DATA+4
MOV
#’R’,DATA+5
MOV
#’E’,DATA+6
MOV
#’D’,DATA+7
MOV
MOV
#$08,CPUSPD
#$0A,BUMPS
LDHX
STHX
#100000/24
DERASE
LDHX
#$7808
STHX
LDHX
LADDR
#$7800
JSR
REDPROG
;Load Bus frequency in MHz * 4
;Load max number of programming steps
;before a failure is returned
;Set erase time in uS/24
;Load the last address of the multi-row
;range; (in this case, 2 rows)
;into LADDR
;Load the first address of the
;multi-row range into H:X
;Call through jump table.
4.12 Low-Power Modes
The WAIT and STOP instructions put the MCU in low powerconsumption standby modes.
4.12.1 Wait Mode
Putting the MCU into wait mode while the FLASH 2TS is in read mode
does not affect the operation of the FLASH 2TS memory directly, but
there will be no memory activity since the CPU is inactive.
The WAIT instruction should not be executed while performing a
program or erase operation on the FLASH 2TS. When the MCU is put
into wait mode, the charge pump for the FLASH 2TS is disabled so that
either a program or erase operation will not continue. If the memory is in
either program mode (PGM = 1, HVEN = 1) or erase mode (ERASE = 1,
HVEN = 1), then it will remain in that mode during wait. Exit from wait
mode must now be done with a reset rather than an interrupt because if
Advance Information
62
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
FLASH 2TS Memory
Low-Power Modes
exiting wait with an interrupt, the memory will not be in read mode and
the interrupt vector cannot be read from the memory.
4.12.2 Stop Mode
When the MCU is put into stop mode, if the FLASH 2TS is in read mode,
it will be put into low-power standby.
The STOP instruction should not be executed while performing a
program or erase operation on the FLASH 2TS. When the MCU is put
into stop mode, the charge pump for the FLASH 2TS is disabled so that
either a program or erase operation will not continue. If the memory is in
either program mode (PGM = 1, HVEN = 1) or erase mode (ERASE = 1,
HVEN = 1), then it will remain in that mode during stop. Exit from stop
mode now must be done with a reset rather than an interrupt because if
exiting stop with an interrupt, the memory will not be in read mode and
the interrupt vector cannot be read from the memory.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
FLASH 2TS Memory
63
FLASH 2TS Memory
Advance Information
64
MC68HC908RF2 — Rev. 1
FLASH 2TS Memory
MOTOROLA
Advance Information — MC68HC908RF2
Section 5. Central Processor Unit (CPU)
5.1 Contents
5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4
CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4.1
Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.4.2
Index Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.4.3
Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
5.4.4
Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
5.4.5
Condition Code Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.5
Arithmetic/Logic Unit (ALU) . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5.6
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5.6.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
5.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
5.7
CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 72
5.8
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
5.9
Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Central Processor Unit (CPU)
65
Central Processor Unit (CPU)
5.2 Introduction
The M68HC08 CPU is an enhanced and fully object-code-compatible
version of the M68HC05 CPU. The CPU08 Reference Manual, Motorola
document order number CPU08RM/AD, contains a description of the
CPU instruction set, addressing modes, and architecture.
5.3 Features
Features of the CPU include:
•
Object code fully upward-compatible with M68HC05 Family
•
16-bit stack pointer with stack manipulation instructions
•
16-bit index register with X-register manipulation instructions
•
4-MHz CPU internal bus frequency
•
64-Kbyte program/data memory space
•
16 addressing modes
•
Memory-to-memory data moves without using accumulator
•
Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions
•
Enhanced binary-coded decimal (BCD) data handling
•
Modular architecture with expandable internal bus definition for
extension of addressing range beyond 64 Kbytes
•
Low-power stop and wait modes
5.4 CPU Registers
Figure 5-1 shows the five CPU registers. CPU registers are not part of
the memory map.
Advance Information
66
MC68HC908RF2 — Rev. 1
Central Processor Unit (CPU)
MOTOROLA
Central Processor Unit (CPU)
CPU Registers
7
0
ACCUMULATOR (A)
15
0
H
INDEX REGISTER (H:X)
X
0
15
STACK POINTER (SP)
15
0
PROGRAM COUNTER (PC)
7
0
V 1 1 H I N Z C
CONDITION CODE REGISTER (CCR)
CARRY/BORROW FLAG
ZERO FLAG
NEGATIVE FLAG
INTERRUPT MASK
HALF-CARRY FLAG
TWO’S COMPLEMENT OVERFLOW FLAG
Figure 5-1. CPU Registers
5.4.1 Accumulator
The accumulator is a general-purpose 8-bit register. The CPU uses the
accumulator to hold operands and the results of arithmetic/logic
operations.
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
Unaffected by reset
Figure 5-2. Accumulator (A)
5.4.2 Index Register
The 16-bit index register allows indexed addressing of a 64-Kbyte
memory space. H is the upper byte of the index register, and X is the
lower byte. H:X is the concatenated 16-bit index register.
In the indexed addressing modes, the CPU uses the contents of the
index register to determine the conditional address of the operand.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Central Processor Unit (CPU)
67
Central Processor Unit (CPU)
The index register can serve also as a temporary data storage location.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Bit
0
0
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
Read:
Write:
Reset:
X = Indeterminate
Figure 5-3. Index Register (H:X)
5.4.3 Stack Pointer
The stack pointer is a 16-bit register that contains the address of the next
location on the stack. During a reset, the stack pointer is preset to
$00FF. The reset stack pointer (RSP) instruction sets the least
significant byte (LSB) to $FF and does not affect the most significant
byte (MSB). The stack pointer decrements as data is pushed onto the
stack and increments as data is pulled from the stack.
In the stack pointer 8-bit offset and 16-bit offset addressing modes, the
stack pointer can function as an index register to access data on the
stack. The CPU uses the contents of the stack pointer to determine the
conditional address of the operand.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Bit
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Read:
Write:
Reset:
Figure 5-4. Stack Pointer (SP)
NOTE:
For correct operation, the stack pointer must point only to RAM
locations.
Advance Information
68
MC68HC908RF2 — Rev. 1
Central Processor Unit (CPU)
MOTOROLA
Central Processor Unit (CPU)
CPU Registers
5.4.4 Program Counter
The program counter is a 16-bit register that contains the address of the
next instruction or operand to be fetched.
Normally, the program counter automatically increments to the next
sequential memory location every time an instruction or operand is
fetched. Jump, branch, and interrupt operations load the program
counter with an address other than that of the next sequential location.
During reset, the program counter is loaded with the reset vector
address located at $FFFE and $FFFF. The vector address is the
address of the first instruction to be executed after exiting the reset state.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
Bit
0
1
Read:
Write:
Reset:
Loaded with vector from $FFFE and $FFFF
Figure 5-5. Program Counter (PC)
5.4.5 Condition Code Register
The 8-bit condition code register (CCR) contains the interrupt mask and
five flags that indicate the results of the instruction just executed. Bits 6
and 5 are set permanently to logic 1. The following paragraphs describe
the functions of the condition code register.
Bit 7
6
5
4
3
2
1
Bit 0
V
1
1
H
I
N
Z
C
X
1
1
X
1
X
X
X
Read:
Write:
Reset:
X = Indeterminate
Figure 5-6. Condition Code Register (CCR)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Central Processor Unit (CPU)
69
Central Processor Unit (CPU)
V — Overflow Flag
The CPU sets the overflow flag when a two's complement overflow
occurs. The signed branch instructions BGT, BGE, BLE, and BLT use
the overflow flag.
1 = Overflow
0 = No overflow
H — Half-Carry Flag
The CPU sets the half-carry flag when a carry occurs between
accumulator bits 3 and 4 during an add-without-carry (ADD) or
add-with-carry (ADC) operation. The half-carry flag is required for
binary-coded decimal (BCD) arithmetic operations. The DAA
instruction uses the states of the H and C flags to determine the
appropriate correction factor.
1 = Carry between bits 3 and 4
0 = No carry between bits 3 and 4
I — Interrupt Mask Bit
When the interrupt mask is set, all maskable CPU interrupts are
disabled. CPU interrupts are enabled when the interrupt mask is
cleared. When a CPU interrupt occurs, the interrupt mask is set
automatically after the CPU registers are saved on the stack, but
before the interrupt vector is fetched.
1 = Interrupts disabled
0 = Interrupts enabled
NOTE:
To maintain M6805 compatibility, the upper byte of the index register (H)
is not stacked automatically. If the interrupt service routine modifies H,
then the user must stack and unstack H using the PSHH and PULH
instructions.
After the I bit is cleared, the highest-priority interrupt request is
serviced first.
A return-from-interrupt (RTI) instruction pulls the CPU registers from
the stack and restores the interrupt mask from the stack. After any
reset, the interrupt mask is set and can be cleared only by the clear
interrupt mask software instruction (CLI).
Advance Information
70
MC68HC908RF2 — Rev. 1
Central Processor Unit (CPU)
MOTOROLA
Central Processor Unit (CPU)
Arithmetic/Logic Unit (ALU)
N — Negative Flag
The CPU sets the negative flag when an arithmetic operation, logic
operation, or data manipulation produces a negative result, setting bit
7 of the result.
1 = Negative result
0 = Non-negative result
Z — Zero Flag
The CPU sets the zero flag when an arithmetic operation, logic
operation, or data manipulation produce a result of $00.
1 = Zero result
0 = Non-zero result
C — Carry/Borrow Flag
The CPU sets the carry/borrow flag when an addition operation
produces a carry out of bit 7 of the accumulator or when a subtraction
operation requires a borrow. Some instructions — such as bit test and
branch, shift, and rotate — also clear or set the carry/borrow flag.
1 = Carry out of bit 7
0 = No carry out of bit 7
5.5 Arithmetic/Logic Unit (ALU)
The ALU performs the arithmetic and logic operations defined by the
instruction set.
Refer to the CPU08 Reference Manual, Motorola document order
number CPU08RM/AD, for a description of the instructions and
addressing modes and more detail about the architecture of the CPU.
5.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low
power-consumption standby modes.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Central Processor Unit (CPU)
71
Central Processor Unit (CPU)
5.6.1 Wait Mode
The WAIT instruction:
•
Clears the interrupt mask (I bit) in the condition code register,
enabling interrupts. After exit from wait mode by interrupt, the I bit
remains clear. After exit by reset, the I bit is set.
•
Disables the CPU clock
5.6.2 Stop Mode
The STOP instruction:
•
Clears the interrupt mask (I bit) in the condition code register,
enabling external interrupts. After exit from stop mode by external
interrupt, the I bit remains clear. After exit by reset, the I bit is set.
•
Disables the CPU clock
After exiting stop mode, the CPU clock begins running after the oscillator
stabilization delay.
5.7 CPU During Break Interrupts
If the break module is enabled, a break interrupt causes the CPU to
execute the software interrupt instruction (SWI) at the completion of the
current CPU instruction. (See Section 7. Break Module (BRK).) The
program counter vectors to $FFFC–$FFFD ($FEFC–$FEFD in monitor
mode).
A return-from-interrupt instruction (RTI) in the break routine ends the
break interrupt and returns the MCU to normal operation if the break
interrupt has been deasserted.
5.8 Instruction Set Summary
Table 5-1 provides a summary of the M68HC08 instruction set.
Advance Information
72
MC68HC908RF2 — Rev. 1
Central Processor Unit (CPU)
MOTOROLA
Central Processor Unit (CPU)
Instruction Set Summary
V H I N Z C
ADC #opr
ADC opr
ADC opr
ADC opr,X
ADC opr,X
ADC ,X
ADC opr,SP
ADC opr,SP
A ← (A) + (M) + (C)
Add with Carry
IMM
DIR
EXT
– IX2
IX1
IX
SP1
SP2
A9
B9
C9
D9
E9
F9
9EE9
9ED9
ii
dd
hh ll
ee ff
ff
IMM
DIR
EXT
– IX2
IX1
IX
SP1
SP2
AB
BB
CB
DB
EB
FB
9EEB
9EDB
ii
dd
hh ll
ee ff
ff
ADD #opr
ADD opr
ADD opr
ADD opr,X
ADD opr,X
ADD ,X
ADD opr,SP
ADD opr,SP
Add without Carry
AIS #opr
Add Immediate Value (Signed) to SP
SP ← (SP) + (16 « M)
– – – – – – IMM
AIX #opr
Add Immediate Value (Signed) to H:X
H:X ← (H:X) + (16 « M)
A ← (A) & (M)
AND #opr
AND opr
AND opr
AND opr,X
AND opr,X
AND ,X
AND opr,SP
AND opr,SP
ASL opr
ASLA
ASLX
ASL opr,X
ASL ,X
ASL opr,SP
Arithmetic Shift Left
(Same as LSL)
C
b7
ASR opr
ASRA
ASRX
ASR opr,X
ASR opr,X
ASR opr,SP
Arithmetic Shift Right
BCC rel
Branch if Carry Bit Clear
ff
ee ff
A7
ii
2
– – – – – – IMM
AF
ii
2
IMM
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
A4
B4
C4
D4
E4
F4
9EE4
9ED4
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
0
DIR
INH
– – INH
IX1
IX
SP1
38 dd
48
58
68 ff
78
9E68 ff
4
1
1
4
3
5
C
DIR
INH
– – INH
IX1
IX
SP1
37 dd
47
57
67 ff
77
9E67 ff
4
1
1
4
3
5
b0
b7
2
3
4
4
3
2
4
5
2
3
4
4
3
2
4
5
A ← (A) + (M)
Logical AND
ff
ee ff
Cycles
Description
Operand
Operation
Effect
on CCR
Opcode
Source
Form
Address
Mode
Table 5-1. Instruction Set Summary (Sheet 1 of 7)
b0
PC ← (PC) + 2 + rel ? (C) = 0
– – – – – – REL
Mn ← 0
DIR
DIR
DIR
DIR
– – – – – –
DIR
DIR
DIR
DIR
(b0)
(b1)
(b2)
(b3)
(b4)
(b5)
(b6)
(b7)
ff
ee ff
24
rr
3
11
13
15
17
19
1B
1D
1F
dd
dd
dd
dd
dd
dd
dd
dd
4
4
4
4
4
4
4
4
BCLR n, opr
Clear Bit n in M
BCS rel
Branch if Carry Bit Set (Same as BLO)
PC ← (PC) + 2 + rel ? (C) = 1
– – – – – – REL
25
rr
3
BEQ rel
Branch if Equal
PC ← (PC) + 2 + rel ? (Z) = 1
– – – – – – REL
27
rr
3
BGE opr
Branch if Greater Than or Equal To
(Signed Operands)
PC ← (PC) + 2 + rel ? (N ⊕ V) = 0
– – – – – – REL
90
rr
3
BGT opr
Branch if Greater Than (Signed
Operands)
PC ← (PC) + 2 + rel ? (Z) | (N ⊕ V) = 0 – – – – – – REL
92
rr
3
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Central Processor Unit (CPU)
73
Central Processor Unit (CPU)
Effect
on CCR
V H I N Z C
Cycles
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 5-1. Instruction Set Summary (Sheet 2 of 7)
BHCC rel
Branch if Half Carry Bit Clear
PC ← (PC) + 2 + rel ? (H) = 0
– – – – – – REL
28
rr
BHCS rel
Branch if Half Carry Bit Set
PC ← (PC) + 2 + rel ? (H) = 1
– – – – – – REL
29
rr
BHI rel
Branch if Higher
PC ← (PC) + 2 + rel ? (C) | (Z) = 0
– – – – – – REL
22
rr
3
BHS rel
Branch if Higher or Same
(Same as BCC)
PC ← (PC) + 2 + rel ? (C) = 0
– – – – – – REL
24
rr
3
BIH rel
Branch if IRQ Pin High
PC ← (PC) + 2 + rel ? IRQ = 1
– – – – – – REL
2F
rr
3
BIL rel
Branch if IRQ Pin Low
PC ← (PC) + 2 + rel ? IRQ = 0
– – – – – – REL
2E
rr
3
(A) & (M)
IMM
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
A5
B5
C5
D5
E5
F5
9EE5
9ED5
ii
dd
hh ll
ee ff
ff
ff
ee ff
2
3
4
4
3
2
4
5
93
rr
3
BIT #opr
BIT opr
BIT opr
BIT opr,X
BIT opr,X
BIT ,X
BIT opr,SP
BIT opr,SP
Bit Test
BLE opr
Branch if Less Than or Equal To
(Signed Operands)
BLO rel
Branch if Lower (Same as BCS)
BLS rel
PC ← (PC) + 2 + rel ? (Z) | (N ⊕ V) = 1 – – – – – – REL
3
3
PC ← (PC) + 2 + rel ? (C) = 1
– – – – – – REL
25
rr
3
Branch if Lower or Same
PC ← (PC) + 2 + rel ? (C) | (Z) = 1
– – – – – – REL
23
rr
3
BLT opr
Branch if Less Than (Signed Operands)
PC ← (PC) + 2 + rel ? (N ⊕ V) =1
– – – – – – REL
91
rr
3
BMC rel
Branch if Interrupt Mask Clear
PC ← (PC) + 2 + rel ? (I) = 0
– – – – – – REL
2C
rr
3
BMI rel
Branch if Minus
PC ← (PC) + 2 + rel ? (N) = 1
– – – – – – REL
2B
rr
3
BMS rel
Branch if Interrupt Mask Set
PC ← (PC) + 2 + rel ? (I) = 1
– – – – – – REL
2D
rr
3
BNE rel
Branch if Not Equal
PC ← (PC) + 2 + rel ? (Z) = 0
– – – – – – REL
26
rr
3
BPL rel
Branch if Plus
PC ← (PC) + 2 + rel ? (N) = 0
– – – – – – REL
2A
rr
3
BRA rel
Branch Always
PC ← (PC) + 2 + rel
– – – – – – REL
20
rr
3
PC ← (PC) + 3 + rel ? (Mn) = 0
DIR
DIR
DIR
DIR
– – – – – DIR
DIR
DIR
DIR
01
03
05
07
09
0B
0D
0F
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
5
5
5
5
5
5
5
5
PC ← (PC) + 2
– – – – – – REL
21
rr
3
PC ← (PC) + 3 + rel ? (Mn) = 1
DIR
DIR
DIR
DIR
– – – – – DIR
DIR
DIR
DIR
00
02
04
06
08
0A
0C
0E
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
5
5
5
5
5
5
5
5
BRCLR n,opr,rel Branch if Bit n in M Clear
BRN rel
Branch Never
BRSET n,opr,rel Branch if Bit n in M Set
Advance Information
74
(b0)
(b1)
(b2)
(b3)
(b4)
(b5)
(b6)
(b7)
(b0)
(b1)
(b2)
(b3)
(b4)
(b5)
(b6)
(b7)
MC68HC908RF2 — Rev. 1
Central Processor Unit (CPU)
MOTOROLA
Central Processor Unit (CPU)
Instruction Set Summary
V H I N Z C
BSET n,opr
Set Bit n in M
BSR rel
Branch to Subroutine
10
12
14
16
18
1A
1C
1E
dd
dd
dd
dd
dd
dd
dd
dd
4
4
4
4
4
4
4
4
rr
4
dd rr
ii rr
ii rr
ff rr
rr
ff rr
5
4
4
5
4
6
Mn ← 1
DIR
DIR
DIR
– – – – – – DIR
DIR
DIR
DIR
DIR
PC ← (PC) + 2; push (PCL)
SP ← (SP) – 1; push (PCH)
SP ← (SP) – 1
PC ← (PC) + rel
– – – – – – REL
AD
DIR
IMM
IMM
– – – – – – IX1+
IX+
SP1
31
41
51
61
71
9E61
PC ← (PC)
PC ← (PC)
PC ← (PC)
PC ← (PC)
PC ← (PC)
PC ← (PC)
CBEQ opr,rel
CBEQA #opr,rel
CBEQX #opr,rel
CBEQ opr,X+,rel Compare and Branch if Equal
CBEQ X+,rel
CBEQ opr,SP,rel
+ 3 + rel ? (A)
+ 3 + rel ? (A)
+ 3 + rel ? (X)
+ 3 + rel ? (A)
+ 2 + rel ? (A)
+ 4 + rel ? (A)
– (M)
– (M)
– (M)
– (M)
– (M)
– (M)
= $00
= $00
= $00
= $00
= $00
= $00
(b0)
(b1)
(b2)
(b3)
(b4)
(b5)
(b6)
(b7)
Cycles
Effect
on CCR
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 5-1. Instruction Set Summary (Sheet 3 of 7)
CLC
Clear Carry Bit
C←0
– – – – – 0 INH
98
1
CLI
Clear Interrupt Mask
I←0
– – 0 – – – INH
9A
2
M ← $00
A ← $00
X ← $00
H ← $00
M ← $00
M ← $00
M ← $00
DIR
INH
INH
0 – – 0 1 – INH
IX1
IX
SP1
3F dd
4F
5F
8C
6F ff
7F
9E6F ff
(A) – (M)
IMM
DIR
EXT
– – IX2
IX1
IX
SP1
SP2
A1
B1
C1
D1
E1
F1
9EE1
9ED1
DIR
INH
INH
0 – – 1
IX1
IX
SP1
33 dd
43
53
63 ff
73
9E63 ff
CLR opr
CLRA
CLRX
CLRH
CLR opr,X
CLR ,X
CLR opr,SP
CMP #opr
CMP opr
CMP opr
CMP opr,X
CMP opr,X
CMP ,X
CMP opr,SP
CMP opr,SP
Clear
Compare A with M
COM opr
COMA
COMX
COM opr,X
COM ,X
COM opr,SP
Complement (One’s Complement)
CPHX #opr
CPHX opr
Compare H:X with M
CPX #opr
CPX opr
CPX opr
CPX ,X
CPX opr,X
CPX opr,X
CPX opr,SP
CPX opr,SP
Compare X with M
DAA
Decimal Adjust A
M←
A←
X←
M←
M←
M←
(M) = $FF – (M)
(A) = $FF – (M)
(X) = $FF – (M)
(M) = $FF – (M)
(M) = $FF – (M)
(M) = $FF – (M)
ff
ee ff
2
3
4
4
3
2
4
5
4
1
1
4
3
5
(H:X) – (M:M + 1)
– – IMM
DIR
65
75
ii ii+1
dd
3
4
(X) – (M)
IMM
DIR
EXT
– – IX2
IX1
IX
SP1
SP2
A3
B3
C3
D3
E3
F3
9EE3
9ED3
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
U – – INH
72
(A) 10
MC68HC908RF2 — Rev. 1
MOTOROLA
ii
dd
hh ll
ee ff
ff
3
1
1
1
3
2
4
ff
ee ff
2
Advance Information
Central Processor Unit (CPU)
75
Central Processor Unit (CPU)
V H I N Z C
DBNZ opr,rel
DBNZA rel
Decrement and Branch if Not Zero
DBNZX rel
DBNZ opr,X,rel
DBNZ X,rel
DBNZ opr,SP,rel
DEC opr
DECA
DECX
DEC opr,X
DEC ,X
DEC opr,SP
Decrement
DIV
Divide
EOR #opr
EOR opr
EOR opr
EOR opr,X
EOR opr,X
EOR ,X
EOR opr,SP
EOR opr,SP
INC opr
INCA
INCX
INC opr,X
INC ,X
INC opr,SP
JMP
JMP
JMP
JMP
JMP
opr
opr
opr,X
opr,X
,X
JSR opr
JSR opr
JSR opr,X
JSR opr,X
JSR ,X
LDA
LDA
LDA
LDA
LDA
LDA
LDA
LDA
#opr
opr
opr
opr,X
opr,X
,X
opr,SP
opr,SP
LDHX #opr
LDHX opr
LDX
LDX
LDX
LDX
LDX
LDX
LDX
LDX
#opr
opr
opr
opr,X
opr,X
,X
opr,SP
opr,SP
Exclusive OR M with A
Increment
Jump
Jump to Subroutine
Load A from M
Load H:X from M
Load X from M
A ← (A) – 1 or M ← (M) – 1 or X ← (X) – 1
DIR
PC ← (PC) + 3 + rel ? (result) ≠ 0
INH
PC ← (PC) + 2 + rel ? (result) ≠ 0
– – – – – – INH
PC ← (PC) + 2 + rel ? (result) ≠ 0
IX1
PC ← (PC) + 3 + rel ? (result) ≠ 0
IX
PC ← (PC) + 2 + rel ? (result) ≠ 0
SP1
PC ← (PC) + 4 + rel ? (result) ≠ 0
3B
4B
5B
6B
7B
9E6B
dd rr
rr
rr
ff rr
rr
ff rr
5
3
3
5
4
6
M ← (M) – 1
A ← (A) – 1
X ← (X) – 1
M ← (M) – 1
M ← (M) – 1
M ← (M) – 1
DIR
INH
– – – INH
IX1
IX
SP1
A ← (H:A)/(X)
H ← Remainder
– – – – INH
52
A ← (A ⊕ M)
IMM
DIR
EXT
0 – – – IX2
IX1
IX
SP1
SP2
A8
B8
C8
D8
E8
F8
9EE8
9ED8
M ← (M) + 1
A ← (A) + 1
X ← (X) + 1
M ← (M) + 1
M ← (M) + 1
M ← (M) + 1
DIR
INH
– – – INH
IX1
IX
SP1
3C dd
4C
5C
6C ff
7C
9E6C ff
PC ← Jump Address
DIR
EXT
– – – – – – IX2
IX1
IX
BC
CC
DC
EC
FC
dd
hh ll
ee ff
ff
2
3
4
3
2
PC ← (PC) + n (n = 1, 2, or 3)
Push (PCL); SP ← (SP) – 1
Push (PCH); SP ← (SP) – 1
PC ← Unconditional Address
DIR
EXT
– – – – – – IX2
IX1
IX
BD
CD
DD
ED
FD
dd
hh ll
ee ff
ff
4
5
6
5
4
A ← (M)
IMM
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
A6
B6
C6
D6
E6
F6
9EE6
9ED6
ii
dd
hh ll
ee ff
ff
ff
ee ff
2
3
4
4
3
2
4
5
H:X ← (M:M + 1)
IMM
0 – – – DIR
45
55
ii jj
dd
3
4
X ← (M)
IMM
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
AE
BE
CE
DE
EE
FE
9EEE
9EDE
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
Advance Information
76
Effect
on CCR
Cycles
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 5-1. Instruction Set Summary (Sheet 4 of 7)
3A dd
4A
5A
6A ff
7A
9E6A ff
4
1
1
4
3
5
7
ii
dd
hh ll
ee ff
ff
ff
ee ff
ff
ee ff
2
3
4
4
3
2
4
5
4
1
1
4
3
5
MC68HC908RF2 — Rev. 1
Central Processor Unit (CPU)
MOTOROLA
Central Processor Unit (CPU)
Instruction Set Summary
LSL opr
LSLA
LSLX
LSL opr,X
LSL ,X
LSL opr,SP
Logical Shift Left
(Same as ASL)
Logical Shift Right
MOV
MOV
MOV
MOV
Move
MUL
0
NOP
No Operation
NSA
Nibble Swap A
4
1
1
4
3
5
C
DIR
INH
– – 0 INH
IX1
IX
SP1
34 dd
44
54
64 ff
74
9E64 ff
4
1
1
4
3
5
b0
dd dd
dd
ii dd
dd
5
4
4
4
H:X ← (H:X) + 1 (IX+D, DIX+)
DD
0 – – – DIX+
IMD
IX+D
4E
5E
6E
7E
X:A ← (X) × (A)
– 0 – – – 0 INH
42
M ← –(M) = $00 – (M)
A ← –(A) = $00 – (A)
X ← –(X) = $00 – (X)
M ← –(M) = $00 – (M)
M ← –(M) = $00 – (M)
DIR
INH
– – INH
IX1
IX
SP1
None
– – – – – – INH
9D
1
A ← (A[3:0]:A[7:4])
– – – – – – INH
62
3
A ← (A) | (M)
IMM
DIR
EXT
IX2
0 – – –
IX1
IX
SP1
SP2
AA
BA
CA
DA
EA
FA
9EEA
9EDA
(M)Destination ← (M)Source
Unsigned multiply
Negate (Two’s Complement)
38 dd
48
58
68 ff
78
9E68 ff
b0
b7
NEG opr
NEGA
NEGX
NEG opr,X
NEG ,X
NEG opr,SP
0
DIR
INH
– – INH
IX1
IX
SP1
C
b7
Cycles
V H I N Z C
LSR opr
LSRA
LSRX
LSR opr,X
LSR ,X
LSR opr,SP
opr,opr
opr,X+
#opr,opr
X+,opr
Effect
on CCR
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 5-1. Instruction Set Summary (Sheet 5 of 7)
5
30 dd
40
50
60 ff
70
9E60 ff
4
1
1
4
3
5
2
3
4
4
3
2
4
5
ORA #opr
ORA opr
ORA opr
ORA opr,X
ORA opr,X
ORA ,X
ORA opr,SP
ORA opr,SP
Inclusive OR A and M
PSHA
Push A onto Stack
Push (A); SP ← (SP) – 1
– – – – – – INH
87
2
PSHH
Push H onto Stack
Push (H); SP ← (SP) – 1
– – – – – – INH
8B
2
PSHX
Push X onto Stack
Push (X); SP ← (SP) – 1
– – – – – – INH
89
2
PULA
Pull A from Stack
SP ← (SP + 1); Pull (A)
– – – – – – INH
86
2
PULH
Pull H from Stack
SP ← (SP + 1); Pull (H)
– – – – – – INH
8A
2
PULX
Pull X from Stack
SP ← (SP + 1); Pull (X)
– – – – – – INH
88
2
C
DIR
INH
– – INH
IX1
IX
SP1
39 dd
49
59
69 ff
79
9E69 ff
4
1
1
4
3
5
DIR
INH
– – INH
IX1
IX
SP1
36 dd
46
56
66 ff
76
9E66 ff
4
1
1
4
3
5
ROL opr
ROLA
ROLX
ROL opr,X
ROL ,X
ROL opr,SP
ROR opr
RORA
RORX
ROR opr,X
ROR ,X
ROR opr,SP
Rotate Left through Carry
b7
b0
C
Rotate Right through Carry
b7
b0
MC68HC908RF2 — Rev. 1
MOTOROLA
ii
dd
hh ll
ee ff
ff
ff
ee ff
Advance Information
Central Processor Unit (CPU)
77
Central Processor Unit (CPU)
Effect
on CCR
V H I N Z C
Cycles
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 5-1. Instruction Set Summary (Sheet 6 of 7)
Reset Stack Pointer
SP ← $FF
– – – – – – INH
9C
1
RTI
Return from Interrupt
SP ← (SP) + 1; Pull (CCR)
SP ← (SP) + 1; Pull (A)
SP ← (SP) + 1; Pull (X)
SP ← (SP) + 1; Pull (PCH)
SP ← (SP) + 1; Pull (PCL)
INH
80
7
RTS
Return from Subroutine
SP ← SP + 1; Pull (PCH)
SP ← SP + 1; Pull (PCL)
– – – – – – INH
81
4
A ← (A) – (M) – (C)
IMM
DIR
EXT
– – IX2
IX1
IX
SP1
SP2
A2
B2
C2
D2
E2
F2
9EE2
9ED2
RSP
SBC
SBC
SBC
SBC
SBC
SBC
SBC
SBC
#opr
opr
opr
opr,X
opr,X
,X
opr,SP
opr,SP
Subtract with Carry
ii
dd
hh ll
ee ff
ff
ff
ee ff
2
3
4
4
3
2
4
5
SEC
Set Carry Bit
C←1
– – – – – 1 INH
99
1
SEI
Set Interrupt Mask
I←1
– – 1 – – – INH
9B
2
M ← (A)
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
B7
C7
D7
E7
F7
9EE7
9ED7
(M:M + 1) ← (H:X)
0 – – – DIR
35
I ← 0; Stop Oscillator
– – 0 – – – INH
8E
M ← (X)
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
BF
CF
DF
EF
FF
9EEF
9EDF
dd
hh ll
ee ff
ff
IMM
DIR
EXT
– – IX2
IX1
IX
SP1
SP2
A0
B0
C0
D0
E0
F0
9EE0
9ED0
ii
dd
hh ll
ee ff
ff
– – 1 – – – INH
83
9
STA opr
STA opr
STA opr,X
STA opr,X
STA ,X
STA opr,SP
STA opr,SP
Store A in M
STHX opr
Store H:X in M
STOP
Enable IRQ Pin; Stop Oscillator
STX
STX
STX
STX
STX
STX
STX
opr
opr
opr,X
opr,X
,X
opr,SP
opr,SP
SUB #opr
SUB opr
SUB opr
SUB opr,X
SUB opr,X
SUB ,X
SUB opr,SP
SUB opr,SP
Store X in M
Subtract
A ← (A) – (M)
ff
ee ff
3
4
4
3
2
4
5
dd
4
dd
hh ll
ee ff
ff
1
ff
ee ff
ff
ee ff
3
4
4
3
2
4
5
2
3
4
4
3
2
4
5
SWI
Software Interrupt
PC ← (PC) + 1; Push (PCL)
SP ← (SP) – 1; Push (PCH)
SP ← (SP) – 1; Push (X)
SP ← (SP) – 1; Push (A)
SP ← (SP) – 1; Push (CCR)
SP ← (SP) – 1; I ← 1
PCH ← Interrupt Vector High Byte
PCL ← Interrupt Vector Low Byte
TAP
Transfer A to CCR
CCR ← (A)
INH
84
2
TAX
Transfer A to X
X ← (A)
– – – – – – INH
97
1
Advance Information
78
MC68HC908RF2 — Rev. 1
Central Processor Unit (CPU)
MOTOROLA
Central Processor Unit (CPU)
Opcode Map
TPA
Transfer CCR to A
Test for Negative or Zero
TSX
Transfer SP to H:X
TXA
Transfer X to A
TXS
Transfer H:X to SP
Cycles
V H I N Z C
TST opr
TSTA
TSTX
TST opr,X
TST ,X
TST opr,SP
A
C
CCR
dd
dd rr
DD
DIR
DIX+
ee ff
EXT
ff
H
H
hh ll
I
ii
IMD
IMM
INH
IX
IX+
IX+D
IX1
IX1+
IX2
M
N
Effect
on CCR
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 5-1. Instruction Set Summary (Sheet 7 of 7)
A ← (CCR)
– – – – – – INH
(A) – $00 or (X) – $00 or (M) – $00
DIR
INH
INH
0 – – – IX1
IX
SP1
H:X ← (SP) + 1
– – – – – – INH
95
2
A ← (X)
– – – – – – INH
9F
1
(SP) ← (H:X) – 1
– – – – – – INH
94
2
Accumulator
Carry/borrow bit
Condition code register
Direct address of operand
Direct address of operand and relative offset of branch instruction
Direct to direct addressing mode
Direct addressing mode
Direct to indexed with post increment addressing mode
High and low bytes of offset in indexed, 16-bit offset addressing
Extended addressing mode
Offset byte in indexed, 8-bit offset addressing
Half-carry bit
Index register high byte
High and low bytes of operand address in extended addressing
Interrupt mask
Immediate operand byte
Immediate source to direct destination addressing mode
Immediate addressing mode
Inherent addressing mode
Indexed, no offset addressing mode
Indexed, no offset, post increment addressing mode
Indexed with post increment to direct addressing mode
Indexed, 8-bit offset addressing mode
Indexed, 8-bit offset, post increment addressing mode
Indexed, 16-bit offset addressing mode
Memory location
Negative bit
n
opr
PC
PCH
PCL
REL
rel
rr
SP1
SP2
SP
U
V
X
Z
&
|
⊕
()
–( )
#
«
←
?
:
—
85
3D dd
4D
5D
6D ff
7D
9E6D ff
1
3
1
1
3
2
4
Any bit
Operand (one or two bytes)
Program counter
Program counter high byte
Program counter low byte
Relative addressing mode
Relative program counter offset byte
Relative program counter offset byte
Stack pointer, 8-bit offset addressing mode
Stack pointer 16-bit offset addressing mode
Stack pointer
Undefined
Overflow bit
Index register low byte
Zero bit
Logical AND
Logical OR
Logical EXCLUSIVE OR
Contents of
Negation (two’s complement)
Immediate value
Sign extend
Loaded with
If
Concatenated with
Set or cleared
Not affected
5.9 Opcode Map
The opcode map is provided in Table 5-2.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Central Processor Unit (CPU)
79
MSB
Branch
REL
DIR
INH
3
4
0
2
3
4
5
6
7
8
9
A
B
C
D
MOTOROLA
MC68HC908RF2 — Rev. 1
1
2
5
BRSET0
3 DIR
5
BRCLR0
3 DIR
5
BRSET1
3 DIR
5
BRCLR1
3 DIR
5
BRSET2
3 DIR
5
BRCLR2
3 DIR
5
BRSET3
3 DIR
5
BRCLR3
3 DIR
5
BRSET4
3 DIR
5
BRCLR4
3 DIR
5
BRSET5
3 DIR
5
BRCLR5
3 DIR
5
BRSET6
3 DIR
5
BRCLR6
3 DIR
5
BRSET7
3 DIR
5
BRCLR7
3 DIR
4
BSET0
2 DIR
4
BCLR0
2 DIR
4
BSET1
2 DIR
4
BCLR1
2 DIR
4
BSET2
2 DIR
4
BCLR2
2 DIR
4
BSET3
2 DIR
4
BCLR3
2 DIR
4
BSET4
2 DIR
4
BCLR4
2 DIR
4
BSET5
2 DIR
4
BCLR5
2 DIR
4
BSET6
2 DIR
4
BCLR6
2 DIR
4
BSET7
2 DIR
4
BCLR7
2 DIR
3
BRA
2 REL
3
BRN
2 REL
3
BHI
2 REL
3
BLS
2 REL
3
BCC
2 REL
3
BCS
2 REL
3
BNE
2 REL
3
BEQ
2 REL
3
BHCC
2 REL
3
BHCS
2 REL
3
BPL
2 REL
3
BMI
2 REL
3
BMC
2 REL
3
BMS
2 REL
3
BIL
2 REL
3
BIH
2 REL
5
6
1
NEGX
1 INH
4
CBEQX
3 IMM
7
DIV
1 INH
1
COMX
1 INH
1
LSRX
1 INH
4
LDHX
2 DIR
1
RORX
1 INH
1
ASRX
1 INH
1
LSLX
1 INH
1
ROLX
1 INH
1
DECX
1 INH
3
DBNZX
2 INH
1
INCX
1 INH
1
TSTX
1 INH
4
MOV
2 DIX+
1
CLRX
1 INH
4
NEG
2
IX1
5
CBEQ
3 IX1+
3
NSA
1 INH
4
COM
2 IX1
4
LSR
2 IX1
3
CPHX
3 IMM
4
ROR
2 IX1
4
ASR
2 IX1
4
LSL
2 IX1
4
ROL
2 IX1
4
DEC
2 IX1
5
DBNZ
3 IX1
4
INC
2 IX1
3
TST
2 IX1
4
MOV
3 IMD
3
CLR
2 IX1
SP1
IX
9E6
7
Control
INH
INH
8
9
IMM
DIR
EXT
A
B
C
Register/Memory
IX2
SP2
IX1
SP1
IX
D
9ED
E
9EE
F
4
SUB
IX2
4
CMP
IX2
4
SBC
IX2
4
CPX
IX2
4
AND
IX2
4
BIT
IX2
4
LDA
IX2
4
STA
IX2
4
EOR
IX2
4
ADC
IX2
4
ORA
IX2
4
ADD
IX2
4
JMP
IX2
6
JSR
IX2
4
LDX
IX2
4
STX
IX2
5
SUB
4 SP2
5
CMP
4 SP2
5
SBC
4 SP2
5
CPX
4 SP2
5
AND
4 SP2
5
BIT
4 SP2
5
LDA
4 SP2
5
STA
4 SP2
5
EOR
4 SP2
5
ADC
4 SP2
5
ORA
4 SP2
5
ADD
4 SP2
3
SUB
IX1
3
CMP
IX1
3
SBC
IX1
3
CPX
IX1
3
AND
IX1
3
BIT
IX1
3
LDA
IX1
3
STA
IX1
3
EOR
IX1
3
ADC
IX1
3
ORA
IX1
3
ADD
IX1
3
JMP
IX1
5
JSR
IX1
3
LDX
IX1
3
STX
IX1
4
SUB
3 SP1
4
CMP
3 SP1
4
SBC
3 SP1
4
CPX
3 SP1
4
AND
3 SP1
4
BIT
3 SP1
4
LDA
3 SP1
4
STA
3 SP1
4
EOR
3 SP1
4
ADC
3 SP1
4
ORA
3 SP1
4
ADD
3 SP1
2
SUB
IX
2
CMP
IX
2
SBC
IX
2
CPX
IX
2
AND
IX
2
BIT
IX
2
LDA
IX
2
STA
IX
2
EOR
IX
2
ADC
IX
2
ORA
IX
2
ADD
IX
2
JMP
IX
4
JSR
IX
2
LDX
IX
2
STX
IX
LSB
1
Central Processor Unit (CPU)
0
Read-Modify-Write
INH
IX1
E
F
1
4
NEGA
NEG
2 DIR 1 INH
4
5
CBEQ CBEQA
3 DIR 3 IMM
5
MUL
1 INH
1
4
COMA
COM
2 DIR 1 INH
1
4
LSRA
LSR
2 DIR 1 INH
3
4
LDHX
STHX
2 DIR 3 IMM
1
4
RORA
ROR
2 DIR 1 INH
1
4
ASRA
ASR
2 DIR 1 INH
1
4
LSLA
LSL
2 DIR 1 INH
1
4
ROLA
ROL
2 DIR 1 INH
1
4
DECA
DEC
2 DIR 1 INH
3
5
DBNZ DBNZA
3 DIR 2 INH
1
4
INCA
INC
2 DIR 1 INH
1
3
TSTA
TST
2 DIR 1 INH
5
MOV
3 DD
1
3
CLRA
CLR
2 DIR 1 INH
INH Inherent
REL Relative
IMM Immediate
IX
Indexed, No Offset
DIR Direct
IX1 Indexed, 8-Bit Offset
EXT Extended
IX2 Indexed, 16-Bit Offset
DD Direct-Direct
IMD Immediate-Direct
IX+D Indexed-Direct DIX+ Direct-Indexed
*Pre-byte for stack pointer indexed instructions
3
5
NEG
NEG
3 SP1 1 IX
4
6
CBEQ
CBEQ
4 SP1 2 IX+
2
DAA
1 INH
3
5
COM
COM
3 SP1 1 IX
3
5
LSR
LSR
3 SP1 1 IX
4
CPHX
2 DIR
3
5
ROR
ROR
3 SP1 1 IX
3
5
ASR
ASR
3 SP1 1 IX
3
5
LSL
LSL
3 SP1 1 IX
3
5
ROL
ROL
3 SP1 1 IX
3
5
DEC
DEC
3 SP1 1 IX
4
6
DBNZ
DBNZ
4 SP1 2 IX
3
5
INC
INC
3 SP1 1 IX
2
4
TST
TST
3 SP1 1 IX
4
MOV
2 IX+D
2
4
CLR
CLR
3 SP1 1 IX
SP1 Stack Pointer, 8-Bit Offset
SP2 Stack Pointer, 16-Bit Offset
IX+ Indexed, No Offset with
Post Increment
IX1+ Indexed, 1-Byte Offset with
Post Increment
3
7
BGE
RTI
1 INH 2 REL
3
4
BLT
RTS
1 INH 2 REL
3
BGT
2 REL
3
9
BLE
SWI
1 INH 2 REL
2
2
TXS
TAP
1 INH 1 INH
2
1
TSX
TPA
1 INH 1 INH
2
PULA
1 INH
1
2
TAX
PSHA
1 INH 1 INH
1
2
CLC
PULX
1 INH 1 INH
1
2
SEC
PSHX
1 INH 1 INH
2
2
CLI
PULH
1 INH 1 INH
2
2
SEI
PSHH
1 INH 1 INH
1
1
RSP
CLRH
1 INH 1 INH
1
NOP
1 INH
1
STOP
*
1 INH
1
1
TXA
WAIT
1 INH 1 INH
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
SUB
2 DIR
3
CMP
2 DIR
3
SBC
2 DIR
3
CPX
2 DIR
3
AND
2 DIR
3
BIT
2 DIR
3
LDA
2 DIR
3
STA
2 DIR
3
EOR
2 DIR
3
ADC
2 DIR
3
ORA
2 DIR
3
ADD
2 DIR
2
JMP
2 DIR
4
4
JSR
BSR
REL 2 DIR
3
2
LDX
LDX
IMM 2 DIR
3
2
STX
AIX
IMM 2 DIR
2
SUB
IMM
2
CMP
IMM
2
SBC
IMM
2
CPX
IMM
2
AND
IMM
2
BIT
IMM
2
LDA
IMM
2
AIS
IMM
2
EOR
IMM
2
ADC
IMM
2
ORA
IMM
2
ADD
IMM
MSB
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
SUB
EXT
4
CMP
EXT
4
SBC
EXT
4
CPX
EXT
4
AND
EXT
4
BIT
EXT
4
LDA
EXT
4
STA
EXT
4
EOR
EXT
4
ADC
EXT
4
ORA
EXT
4
ADD
EXT
3
JMP
EXT
5
JSR
EXT
4
LDX
EXT
4
STX
EXT
0
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
2
2
2
2
2
2
2
2
2
2
2
2
2
2
5
LDX
4 SP2 2
5
STX
4 SP2 2
0
1
1
1
1
1
1
1
1
1
1
1
1
1
4
LDX
3 SP1 1
4
STX
3 SP1 1
High Byte of Opcode in Hexadecimal
LSB
Low Byte of Opcode in Hexadecimal
1
Cycles
5
BRSET0 Opcode Mnemonic
3 DIR Number of Bytes / Addressing Mode
Central Processor Unit (CPU)
Advance Information
80
Table 5-2. Opcode Map
Bit Manipulation
DIR
DIR
Advance Information — MC68HC908RF2
Section 6. System Integration Module (SIM)
6.1 Contents
6.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.3
SIM Bus Clock Control and Generation . . . . . . . . . . . . . . . . . . 85
6.3.1
Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
6.3.2
Clock Startup from POR or LVI Reset . . . . . . . . . . . . . . . . . 85
6.3.3
Clocks in Stop Mode and Wait Mode . . . . . . . . . . . . . . . . . . 86
6.4
Reset and System Initialization. . . . . . . . . . . . . . . . . . . . . . . . . 86
6.4.1
External Pin Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.4.2
Active Resets from Internal Sources . . . . . . . . . . . . . . . . . . 88
6.4.2.1
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.4.2.2
Computer Operating Properly (COP) Reset. . . . . . . . . . . 90
6.4.2.3
Illegal Opcode Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
6.4.2.4
Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
6.4.2.5
Low-Voltage Inhibit (LVI) Reset . . . . . . . . . . . . . . . . . . . .90
6.5
SIM Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
6.5.1
SIM Counter During Power-On Reset . . . . . . . . . . . . . . . . . 91
6.5.2
SIM Counter During Stop Mode Recovery . . . . . . . . . . . . . . 91
6.5.3
SIM Counter and Reset States. . . . . . . . . . . . . . . . . . . . . . . 91
6.6
Program Exception Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.6.1
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.6.1.1
Hardware Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
6.6.1.2
SWI Instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.6.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.6.3
Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.6.4
Status Flag Protection in Break Mode . . . . . . . . . . . . . . . . . 96
6.7
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
6.7.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
6.7.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
81
System Integration Module (SIM)
6.8
SIM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
6.8.1
SIM Break Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . 99
6.8.2
SIM Reset Status Register . . . . . . . . . . . . . . . . . . . . . . . . 100
6.8.3
SIM Break Flag Control Register . . . . . . . . . . . . . . . . . . . . 101
6.2 Introduction
This section describes the system integration module (SIM). Together
with the central processor unit (CPU), the SIM controls all MCU
activities. The SIM is a system state controller that coordinates CPU and
exception timing. A block diagram of the SIM is shown in Figure 6-1.
Figure 6-2 is a summary of the SIM input/output (I/O) registers.
The SIM is responsible for:
•
Bus clock generation and control for CPU and peripherals:
– Stop/wait/reset/break entry and recovery
– Internal clock control
•
Master reset control, including power-on reset (POR) and
computer operating properly (COP) timeout
•
Interrupt control:
– Acknowledge timing
– Arbitration control timing
– Vector address generation
•
CPU enable/disable timing
Advance Information
82
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
Introduction
MODULE STOP
MODULE WAIT
CPU STOP (FROM CPU)
CPU WAIT (FROM CPU)
STOP/WAIT
CONTROL
SIMOSCEN (TO ICG)
SIM
COUNTER
COP CLOCK
CGMXCLK (FROM ICG)
CGMOUT (FROM ICG)
÷2
CLOCK
CONTROL
RESET
PIN LOGIC
CLOCK GENERATORS
INTERNAL CLOCKS
LVI (FROM LVI MODULE)
POR CONTROL
MASTER
RESET
CONTROL
RESET PIN CONTROL
SIM RESET STATUS REGISTER
ILLEGAL OPCODE (FROM CPU)
ILLEGAL ADDRESS (FROM ADDRESS
MAP DECODERS)
COP (FROM COP MODULE)
RESET
INTERRUPT CONTROL
AND PRIORITY DECODE
INTERRUPT SOURCES
CPU INTERFACE
Figure 6-1. SIM Block Diagram
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
83
System Integration Module (SIM)
Addr.
Register Name
Bit 7
6
5
4
3
2
R
R
R
R
R
R
Read:
SIM Break Status Register
$FE00
(SBSR) Write:
See page 99.
Reset:
1
Bit 0
SBSW
R
See Note
0
Note: Writing a logic 0 clears SBSW
Read:
SIM Reset Status Register
$FE01
(SRSR) Write:
See page 100.
POR:
$FE02
Read:
SIM Break Flag Control
Register (SBFCR) Write:
See page 101.
Reset:
POR
PIN
COP
ILOP
ILAD
0
LVI
0
1
X
X
X
X
X
X
X
BCFE
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
= Unimplemented
R
= Reserved
X = Indeterminate
Figure 6-2. SIM I/O Register Summary
Table 6-1 shows the internal signal names used in this section.
Table 6-1. Signal Name Conventions
Signal Name
Description
CGMXCLK
Selected clock source from internal clock generator module (ICG)
CGMOUT
Clock output from ICG module
Bus clock = CGMOUT divided by two
ICLK
Output from internal clock generator
ECLK
External clock source
IAB
Internal address bus
IDB
internal data bus
PORRST
Signal from the power-on reset module to the SIM
IRST
Internal reset signal
R/W
Read/write signal
Advance Information
84
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
SIM Bus Clock Control and Generation
6.3 SIM Bus Clock Control and Generation
The bus clock generator provides system clock signals for the CPU and
peripherals on the MCU. The system clocks are generated from an
incoming clock, CGMOUT, as shown in Figure 6-3. This clock can come
from either an external oscillator or from the internal clock generator
(ICG) module.
6.3.1 Bus Timing
In user mode, the internal bus frequency is either the crystal oscillator
output (ECLK) divided by four or the ICG output (ICLK) divided by four.
6.3.2 Clock Startup from POR or LVI Reset
When the power-on reset (POR) module or the low-voltage inhibit (LVI)
module generates a reset, the clocks to the CPU and peripherals are
inactive and held in an inactive phase until after 4096 CGMXCLK cycles.
The RST pin is driven low by the SIM during this entire period. The bus
clocks start upon completion of the timeout.
CGMXCLK
ECLK
CLOCK
SELECT
CIRCUIT
ICLK
ICG
GENERATOR
÷2
A
CGMOUT
B S*
*When S = 1,
CGMOUT = B
CS
SIM COUNTER
BUS CLOCK
GENERATORS
÷2
SIM
PTB3
MONITOR MODE
USER MODE
ICG
Figure 6-3. ICG Clock Signals
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
85
System Integration Module (SIM)
6.3.3 Clocks in Stop Mode and Wait Mode
Upon exit from stop mode by an interrupt, break, or reset, the SIM allows
CGMXCLK to clock the SIM counter. The CPU and peripheral clocks do
not become active until after the stop delay timeout. This timeout is
selectable as 4096 or 32 CGMXCLK cycles. (See 6.7.2 Stop Mode.)
In wait mode, the CPU clocks are inactive. Refer to the wait mode
subsection of each module to see if the module is active or inactive in
wait mode. Some modules can be programmed to be active in wait
mode.
6.4 Reset and System Initialization
The MCU has these reset sources:
•
Power-on reset module (POR)
•
External reset pin (RST)
•
Computer operating properly module (COP)
•
Low-voltage inhibit module (LVI)
•
Illegal opcode
•
Illegal address
All of these resets produce the vector $FFFE–FFFF ($FEFE–FEFF in
monitor mode) and assert the internal reset signal (IRST). IRST causes
all registers to be returned to their default values and all modules to be
returned to their reset states.
An internal reset clears the SIM counter (see 6.5 SIM Counter), but an
external reset does not. Each of the resets sets a corresponding bit in
the SIM reset status register (SRSR). (See 6.8 SIM Registers.)
Advance Information
86
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
Reset and System Initialization
6.4.1 External Pin Reset
Pulling the asynchronous RST pin low halts all processing. The PIN bit
of the SIM reset status register (SRSR) is set as long as RST is held low
for a minimum of 67 CGMXCLK cycles, assuming that neither the POR
nor the LVI was the source of the reset.
Figure 6-4 shows the relative timing of an external reset recovery.
PULLED LOW EXTERNAL
RST
PULLED HIGH EXTERNAL
CGMOUT
IAB
PC
VECT H
VECT L
Figure 6-4. External Reset Recovery Timing
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
87
System Integration Module (SIM)
6.4.2 Active Resets from Internal Sources
All internal reset sources actively pull the RST pin low for 32 CGMXCLK
cycles to allow resetting of external peripherals. The internal reset signal
IRST continues to be asserted for an additional 32 cycles.
(See Figure 6-5.) An internal reset can be caused by an illegal address,
illegal opcode, COP timeout, LVI, or POR. (See Figure 6-6.) Note that
for LVI or POR resets, the SIM cycles through 4096 CGMXCLK cycles
during which the SIM forces the RST pin low. The internal reset signal
then follows the sequence from the falling edge of RST shown in
Figure 6-5.
The COP reset is asynchronous to the bus clock.
The active reset feature allows the part to issue a reset to peripherals
and other chips within a system built around the MCU.
IRST
RST
RST PULLED LOW BY MCU
32 CYCLES
32 CYCLES
CGMXCLK
IAB
VECTOR HIGH
Figure 6-5. Internal Reset Timing
ILLEGAL ADDRESS RST
ILLEGAL OPCODE RST
COPRST
LVI
POR
INTERNAL RESET
Figure 6-6. Sources of Internal Reset
Advance Information
88
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
Reset and System Initialization
6.4.2.1 Power-On Reset
When power is first applied to the MCU, the power-on reset module
(POR) generates a pulse to indicate that power-on has occurred. The
external reset pin (RST) is held low while the SIM counter counts out
4096 CGMXCLK cycles. Another 64 CGMXCLK cycles later, the CPU
and memories are released from reset to allow the reset vector
sequence to occur.
At power-on, these events occur:
•
A POR pulse is generated.
•
The internal reset signal is asserted.
•
The SIM enables CGMOUT.
•
Internal clocks to the CPU and modules are held inactive for 4096
CGMXCLK cycles to allow stabilization of the oscillator.
•
The RST pin is driven low during the oscillator stabilization time.
•
The POR bit of the SIM reset status register (SRSR) is set and all
other bits in the register are cleared.
OSC1
PORRST
4096
CYCLES
32
CYCLES
32
CYCLES
CGMXCLK
CGMOUT
RST
$FFFE
IAB
$FFFF
Figure 6-7. POR Recovery
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
89
System Integration Module (SIM)
6.4.2.2 Computer Operating Properly (COP) Reset
The overflow of the COP counter causes an internal reset and sets the
COP bit in the SIM reset status register (SRSR) if the COPD bit in the
CONFIG register is at logic 0. (See Section 11. Computer Operating
Properly Module (COP).)
6.4.2.3 Illegal Opcode Reset
The SIM decodes signals from the CPU to detect illegal instructions. An
illegal instruction sets the ILOP bit in the SIM reset status register
(SRSR) and causes a reset.
If the stop enable bit, STOP, in the configuration register (CONFIG) is
logic 0, the SIM treats the STOP instruction as an illegal opcode and
causes an illegal opcode reset.
6.4.2.4 Illegal Address Reset
An opcode fetch from an unmapped address generates an illegal
address reset. The SIM verifies that the CPU is fetching an opcode prior
to asserting the ILAD bit in the SIM reset status register (SRSR) and
resetting the MCU. A data fetch from an unmapped address does not
generate a reset.
6.4.2.5 Low-Voltage Inhibit (LVI) Reset
The low-voltage inhibit module (LVI) asserts its output to the SIM when
the VDD voltage falls to the VLVR voltage. The LVI bit in the SIM reset
status register (SRSR) is set and a chip reset is asserted if the LVIPWRD
and LVIRSTD bits in the CONFIG register are at logic 0. The RST pin will
be held low until the SIM counts 4096 CGMXCLK cycles after VDD rises
above VLVR+ HLVR. Another 64 CGMXCLK cycles later, the CPU is
released from reset to allow the reset vector sequence to occur. (See
Section 12. Low-Voltage Inhibit (LVI).)
Advance Information
90
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
SIM Counter
6.5 SIM Counter
The SIM counter is used by the power-on reset module (POR) and in
stop mode recovery to allow the oscillator time to stabilize before
enabling the internal bus (IBUS) clocks. The SIM counter also serves as
a prescaler for the computer operating properly module (COP). The SIM
counter overflow supplies the clock for the COP module. The SIM
counter is 12 bits long and is clocked by the falling edge of CGMXCLK.
6.5.1 SIM Counter During Power-On Reset
The power-on reset module (POR) detects power applied to the MCU.
At power-on, the POR circuit asserts the signal PORRST. Once the SIM
is initialized, it enables the internal clock generation module (ICG) to
drive the bus clock state machine.
6.5.2 SIM Counter During Stop Mode Recovery
The SIM counter also is used for stop mode recovery. The STOP
instruction clears the SIM counter. After an interrupt, break, or reset, the
SIM senses the state of the short stop recovery bit, SSREC, in the
CONFIG register. If the SSREC bit is a logic 1, then the stop recovery is
reduced from the normal delay of 4096 CGMXCLK cycles down to 32
CGMXCLK cycles. This is ideal for applications using canned oscillators
that do not require long startup times from stop mode. External crystal
applications should use the full stop recovery time, that is, with SSREC
cleared.
6.5.3 SIM Counter and Reset States
External reset has no effect on the SIM counter. See 6.7.2 Stop Mode
for details. The SIM counter is free-running after all reset states. See
6.4.2 Active Resets from Internal Sources for counter control and
internal reset recovery sequences.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
91
System Integration Module (SIM)
6.6 Program Exception Control
Normal, sequential program execution can be changed in three different
ways:
1. Interrupts:
a. Maskable hardware CPU interrupts
b. Non-maskable software interrupt instruction (SWI)
2. Reset
3. Break interrupts
6.6.1 Interrupts
At the beginning of an interrupt, the CPU saves the CPU register
contents on the stack and sets the interrupt mask (I bit) to prevent
additional interrupts. At the end of an interrupt, the RTI instruction
recovers the CPU register contents from the stack so that normal
processing can resume. Figure 6-8 shows interrupt entry timing.
Figure 6-10 shows interrupt recovery timing.
Interrupts are latched, and arbitration is performed in the SIM at the start
of interrupt processing. The arbitration result is a constant that the CPU
uses to determine which vector to fetch. Once an interrupt is latched by
the SIM, no other interrupt can take precedence, regardless of priority,
until the latched interrupt is serviced (or the I bit is cleared).
(See Figure 6-9.)
MODULE
INTERRUPT
I BIT
IAB
DUMMY
IDB
DUMMY
SP
SP – 1
PC – 1[7:0]
SP – 2
PC–1[15:8]
SP – 3
X
SP – 4
A
VECT H
CCR
VECT L
V DATA H
START ADDR
V DATA L
OPCODE
R/W
Figure 6-8. Interrupt Entry
Advance Information
92
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
Program Exception Control
FROM RESET
YES
BREAK
INTERRUPT?
I BIT
SET?
NO
YES
I BIT SET?
NO
IRQ
INTERRUPT?
YES
NO
STACK CPU REGISTERS
SET I BIT
LOAD PC WITH INTERRUPT VECTOR
AS MANY INTERRUPTS
AS EXIST ON CHIP
FETCH NEXT
INSTRUCTION
SWI
INSTRUCTION?
YES
NO
RTI
INSTRUCTION?
YES
UNSTACK CPU REGISTERS
NO
EXECUTE INSTRUCTION
Figure 6-9. Interrupt Processing
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
93
System Integration Module (SIM)
MODULE
INTERRUPT
I BIT
IAB
SP – 4
IDB
SP – 3
CCR
SP – 2
A
SP – 1
X
SP
PC – 1 [15:8]
PC
PC–1[7:0]
PC + 1
OPCODE
OPERAND
R/W
Figure 6-10. Interrupt Recovery
6.6.1.1 Hardware Interrupts
A hardware interrupt does not stop the current instruction. Processing of
a hardware interrupt begins after completion of the current instruction.
When the current instruction is complete, the SIM checks all pending
hardware interrupts. If interrupts are not masked (I bit clear in the
condition code register), and if the corresponding interrupt enable bit is
set, the SIM proceeds with interrupt processing; otherwise, the next
instruction is fetched and executed.
If more than one interrupt is pending at the end of an instruction
execution, the highest priority interrupt is serviced first. Figure 6-11
demonstrates what happens when two interrupts are pending. If an
interrupt is pending upon exit from the original interrupt service routine,
the pending interrupt is serviced before the LDA instruction is executed.
The LDA opcode is prefetched by both the INT1 and INT2 RTI
instructions. However, in the case of the INT1 RTI prefetch, this is a
redundant operation.
NOTE:
To maintain compatibility with the M68HC05, M6805, and M146805
Families, the H register is not pushed on the stack during interrupt entry.
If the interrupt service routine modifies the H register or uses the indexed
addressing mode, software should save the H register and then restore
it prior to exiting the routine.
Advance Information
94
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
Program Exception Control
CLI
BACKGROUND
ROUTINE
LDA #$FF
INT1
PSHH
INT1 INTERRUPT SERVICE ROUTINE
PULH
RTI
INT2
PSHH
INT2 INTERRUPT SERVICE ROUTINE
PULH
RTI
Figure 6-11. Interrupt Recognition Example
6.6.1.2 SWI Instruction
The SWI instruction is a non-maskable instruction that causes an
interrupt regardless of the state of the interrupt mask (I bit) in the
condition code register.
NOTE:
A software interrupt pushes PC onto the stack. A software interrupt does
not push PC – 1, as a hardware interrupt does.
6.6.2 Reset
All reset sources always have higher priority than interrupts and cannot
be arbitrated.
6.6.3 Break Interrupts
The break module can stop normal program flow at a softwareprogrammable break point by asserting its break interrupt output. (See
Section 7. Break Module (BRK).) The SIM puts the CPU into the break
state by forcing it to the SWI vector location. Refer to the break interrupt
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
95
System Integration Module (SIM)
subsection of each module to see how each module is affected by the
break state.
6.6.4 Status Flag Protection in Break Mode
The SIM controls whether status flags contained in other modules can
be cleared during break mode. The user can select whether flags are
protected from being cleared by properly initializing the break clear flag
enable bit (BCFE) in the break flag control register (BFCR).
Protecting flags in break mode ensures that set flags will not be cleared
while in break mode. This protection allows registers to be freely read
and written during break mode without losing status flag information.
Setting the BCFE bit enables the clearing mechanisms. Once cleared in
break mode, a flag remains cleared even when break mode is exited.
Status flags with a 2-step clearing mechanism — for example, a read of
one register followed by the read or write of another — are protected,
even when the first step is accomplished prior to entering break mode.
Upon leaving break mode, execution of the second step will clear the flag
as normal.
6.7 Low-Power Modes
Executing the WAIT or STOP instruction puts the MCU in a low powerconsumption mode for standby situations. The SIM holds the CPU in a
non-clocked state. The operation of each of these modes is described
here. Both STOP and WAIT clear the interrupt mask (I) in the condition
code register, allowing interrupts to occur.
6.7.1 Wait Mode
In wait mode, the CPU clocks are inactive while one set of peripheral
clocks continues to run. Figure 6-12 shows the timing for wait mode
entry.
A module that is active during wait mode can wake up the CPU with an
interrupt if the interrupt is enabled. Stacking for the interrupt begins one
Advance Information
96
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
Low-Power Modes
cycle after the WAIT instruction during which the interrupt occurred.
Refer to the wait mode subsection of each module to see if the module
is active or inactive in wait mode. Some modules can be programmed to
be active in wait mode.
Wait mode can also be exited by a reset or break. A break interrupt
during wait mode sets the SIM break stop/wait bit, SBSW, in the SIM
break status register (SBSR). If the COP disable bit, COPD, in the mask
option register is logic 0, then the computer operating properly module
(COP) is enabled and remains active in wait mode.
IAB
WAIT ADDR
IDB
WAIT ADDR + 1
PREVIOUS DATA
SAME
NEXT OPCODE
SAME
SAME
SAME
R/W
Note: Previous data can be operand data or the WAIT opcode, depending on the last instruction.
Figure 6-12. Wait Mode Entry Timing
Figure 6-13 and Figure 6-14 show the timing for WAIT recovery.
IAB
IDB
$6E0B
$A6
$A6
$6E0C
$A6
$01
$00FF
$00FE
$0B
$00FD
$00FC
$6E
EXITSTOPWAIT
Note: EXITSTOPWAIT = RST pin or CPU interrupt or break interrupt
Figure 6-13. Wait Recovery from Interrupt or Break
32
CYCLES
IAB
IDB
$6E0B
$A6
$A6
32
CYCLES
RSTVCT H
RSTVCTL
$A6
RST
CGMXCLK
Figure 6-14. Wait Recovery from Internal Reset
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
97
System Integration Module (SIM)
6.7.2 Stop Mode
In stop mode, the SIM counter is reset and the system clocks are
disabled. An interrupt request from a module can cause an exit from stop
mode. Stacking for interrupts begins after the selected stop recovery
time has elapsed. Reset or break also causes an exit from stop mode.
The SIM disables the clock generator module outputs (CGMOUT and
CGMXCLK) in stop mode, stopping the CPU and peripherals. Stop
recovery time is selectable using the SSREC bit in the CONFIG register.
If SSREC is set, stop recovery is reduced from the normal delay of 4096
CGMXCLK cycles down to 32. This is ideal for applications using canned
oscillators that do not require long startup times from stop mode.
NOTE:
External crystal applications should use the full stop recovery time by
clearing the SSREC bit.
A break interrupt during stop mode sets the SIM break stop/wait bit
(SBSW) in the SIM break status register (SBSR).
The SIM counter is held in reset from the execution of the STOP
instruction until the beginning of stop recovery. It is then used to time the
recovery period. Figure 6-15 shows stop mode entry timing.
CPUSTOP
IAB
IDB
STOP ADDR
STOP ADDR + 1
PREVIOUS DATA
SAME
NEXT OPCODE
SAME
SAME
SAME
R/W
Note: Previous data can be operand data or the STOP opcode, depending on the last instruction.
Figure 6-15. Stop Mode Entry Timing
STOP RECOVERY PERIOD
CGMXCLK
INT/BREAK
IAB
STOP +1
STOP + 2
STOP + 2
SP
SP – 1
SP – 2
SP – 3
Figure 6-16. Stop Mode Recovery from Interrupt or Break
Advance Information
98
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
SIM Registers
6.8 SIM Registers
The SIM has three memory mapped registers:
•
SIM break status register, SBSR
•
SIM reset status register, SRSR
•
SIM break flag control register, SBFCR
6.8.1 SIM Break Status Register
The SIM break status register (SBSR) contains a flag to indicate that a
break caused an exit from stop or wait mode.
Address:
$FE00
Bit 7
6
5
4
3
2
R
R
R
R
R
R
Read:
Write:
Reset:
1
SBSW
See Note
Bit 0
R
0
R
= Reserved
Note: Writing a logic 0 clears SBSW.
Figure 6-17. SIM Break Status Register (SBSR)
SBSW — SIM Break Stop/Wait Bit
This status bit is useful in applications requiring a return to wait or stop
mode after exiting from a break interrupt. Clear SBSW by writing a
logic 0 to it. Reset clears SBSW.
1 = Stop mode or wait mode was exited by break interrupt.
0 = Stop mode or wait mode was not exited by break interrupt.
SBSW can be read within the break state SWI routine. The user can
modify the return address on the stack by subtracting one from it.
(See code example.) Writing 0 to the SBSW bit clears it.
;This code works if the H register has been pushed onto the stack in the break
;service routine software. This code should be executed at the end of the
;break service routine software.
HIBYTE
LOBYTE
;
DOLO
RETURN
EQU
5
EQU
6
If not SBSW, do RTI
BRCLR
SBSW, SBSR, RETURN
TST
BNE
DEC
DEC
PULH
RTI
LOBYTE,SP
DOLO
HIBYTE,SP
LOBYTE,SP
;See if wait mode or stop mode was exited
;by break.
;If RETURNLO is not zero,
;then just decrement low byte.
;Else deal with high byte, too.
;Point to WAIT/STOP opcode.
;Restore H register.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
99
System Integration Module (SIM)
6.8.2 SIM Reset Status Register
This register contains six flags that show the source of the last reset. The
status register will clear automatically after reading it. A power-on reset
sets the POR bit.
Address:
Read:
$FE01
Bit 7
6
5
4
3
2
1
Bit 0
POR
PIN
COP
ILOP
ILAD
0
LVI
0
1
X
X
X
X
X
X
X
Write:
POR:
= Unimplemented
X = Indeterminate
Figure 6-18. SIM Reset Status Register (SRSR)
POR — Power-On Reset Bit
1 = Last reset caused by POR circuit
0 = Read of SRSR
PIN — External Reset Bit
1 = Last reset caused by external reset pin (RST)
0 = Read of SRSR
COP — Computer Operating Properly Reset Bit
1 = Last reset caused by COP counter
0 = Read of SRSR
ILOP — Illegal Opcode Reset Bit
1 = Last reset caused by an illegal opcode
0 = Read of SRSR
ILAD — Illegal Address Reset Bit (opcode fetches only)
1 = Last reset caused by an opcode fetch from an illegal address
0 = Read of SRSR
LVI — Low-Voltage Inhibit Reset Bit
1 = Last reset was caused by the LVI circuit
0 = Read of SRSR
Advance Information
100
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
System Integration Module (SIM)
SIM Registers
6.8.3 SIM Break Flag Control Register
The SIM break control register contains a bit that enables software to
clear status bits while the MCU is in a break state.
Address:
$FE02
Bit 7
6
5
4
3
2
1
Bit 0
BCFE
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
R
= Reserved
Figure 6-19. SIM Break Flag Control Register (SBFCR)
BCFE — Break Clear Flag Enable Bit
This read/write bit enables software to clear status bits by accessing
status registers while the MCU is in a break state. To clear status bits
during the break state, the BCFE bit must be set.
1 = Status bits clearable during break
0 = Status bits not clearable during break
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
System Integration Module (SIM)
101
System Integration Module (SIM)
Advance Information
102
MC68HC908RF2 — Rev. 1
System Integration Module (SIM)
MOTOROLA
Advance Information — MC68HC908RF2
Section 7. Break Module (BRK)
7.1 Contents
7.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.4
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
7.4.1
Flag Protection During Break Interrupts . . . . . . . . . . . . . . . 105
7.4.2
CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . .105
7.4.3
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . 106
7.4.4
COP During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . .106
7.5
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
7.5.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
7.5.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
7.6
Break Module Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
7.6.1
Break Status and Control Register . . . . . . . . . . . . . . . . . . .107
7.6.2
Break Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 108
7.2 Introduction
The break module can generate a break interrupt that stops normal
program flow at a defined address to enter a background program.
7.3 Features
Features of the break module (BRK) include:
•
Accessible input/output (I/O) registers during break interrupts
•
CPU-generated break interrupts
•
Software-generated break interrupts
•
COP disabling during break interrupts
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Break Module (BRK)
103
Break Module (BRK)
7.4 Functional Description
When the internal address bus matches the value written in the break
address registers, the break module issues a breakpoint signal to the
CPU. The CPU then loads the instruction register with a software
interrupt instruction (SWI) after completion of the current CPU
instruction. The program counter vectors to $FFFC and $FFFD ($FEFC
and $FEFD in monitor mode).
These events can cause a break interrupt to occur:
•
A CPU-generated address (the address in the program counter)
matches the contents of the break address registers.
•
Software writes a logic 1 to the BRKA bit in the break status and
control register.
When a CPU-generated address matches the contents of the break
address registers, the break interrupt begins after the CPU completes its
current instruction. A return-from-interrupt instruction (RTI) in the break
routine ends the break interrupt and returns the MCU to normal
operation. Figure 7-1 shows the structure of the break module.
IAB[15:8]
BREAK ADDRESS REGISTER HIGH
8-BIT COMPARATOR
IAB[15:0]
CONTROL
BREAK
8-BIT COMPARATOR
BREAK ADDRESS REGISTER LOW
IAB[7:0]
Figure 7-1. Break Module Block Diagram
Advance Information
104
MC68HC908RF2 — Rev. 1
Break Module (BRK)
MOTOROLA
Break Module (BRK)
Functional Description
Addr.
$FE0C
$FE0D
Register Name
Read:
Break Address Register
High (BRKH) Write:
See page 108.
Reset:
Read:
Break Address Register
Low (BRKL) Write:
See page 108.
Reset:
Read:
Break Status and Control
$FE0E
Register (BSCR) Write:
See page 107.
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BRKE
BRKA
0
0
0
0
0
0
0
0
= Unimplemented
Figure 7-2. I/O Register Summary
7.4.1 Flag Protection During Break Interrupts
The system integration module (SIM) controls whether module status
bits can be cleared during the break state. The BCFE bit in the SIM break
flag control register (BFCR) enables software to clear status bits during
the break state. (See 6.8.3 SIM Break Flag Control Register and the
Break Interrupts subsection for each module.)
7.4.2 CPU During Break Interrupts
The CPU starts a break interrupt by:
•
Loading the instruction register with the SWI instruction
•
Loading the program counter with $FFFC and $FFFD ($FEFC and
$FEFD in monitor mode)
The break interrupt begins after completion of the CPU instruction in
progress. If the break address register match occurs on the last cycle of
a CPU instruction, the break interrupt begins immediately.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Break Module (BRK)
105
Break Module (BRK)
7.4.3 TIM During Break Interrupts
A break interrupt stops the timer counter.
7.4.4 COP During Break Interrupts
The COP is disabled during a break interrupt when VHI is present on the
RST pin.
7.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low powerconsumption standby modes.
7.5.1 Wait Mode
If enabled, the break module is active in wait mode.
7.5.2 Stop Mode
The break module is inactive in stop mode. The STOP instruction does
not affect break module register states.
7.6 Break Module Registers
These registers control and monitor operation of the break module:
•
Break status and control register, BSCR
•
Break address register high, BRKH
•
Break address register low, BRKL
Advance Information
106
MC68HC908RF2 — Rev. 1
Break Module (BRK)
MOTOROLA
Break Module (BRK)
Break Module Registers
7.6.1 Break Status and Control Register
The break status and control register (BSCR) contains break module
enable and status bits.
Address:
$FE0E
Bit 7
6
BRKE
BRKA
0
0
Read:
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 7-3. Break Status and Control Register (BSCR)
BRKE — Break Enable Bit
This read/write bit enables breaks on break address register matches.
Clear BRKE by writing a logic 0 to bit 7. Reset clears the BRKE bit.
1 = Breaks enabled on 16-bit address match
0 = Breaks disabled on 16-bit address match
BRKA — Break Active Bit
This read/write status and control bit is set when a break address
match occurs. Writing a logic 1 to BRKA generates a break interrupt.
Clear BRKA by writing a logic 0 to it before exiting the break routine.
1 = Break address match
0 = No break address match
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Break Module (BRK)
107
Break Module (BRK)
7.6.2 Break Address Registers
The break address registers contain the high and low bytes of the
desired breakpoint address. Reset clears the break address registers.
Register Name and Address: BRKH — $FE0C
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Register Name and Address: BRKL — $FE0D
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 7-4. Break Address Registers (BRKH and BRKL)
Advance Information
108
MC68HC908RF2 — Rev. 1
Break Module (BRK)
MOTOROLA
Advance Information — MC68HC908RF2
Section 8. Internal Clock Generator Module (ICG)
8.1 Contents
8.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
8.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
8.4
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
8.4.1
Clock Enable Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
8.4.2
Internal Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . 113
8.4.2.1
Digitally Controlled Oscillator . . . . . . . . . . . . . . . . . . . . . 114
8.4.2.2
Modulo N Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
8.4.2.3
Frequency Comparator . . . . . . . . . . . . . . . . . . . . . . . . . 114
8.4.2.4
Digital Loop Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
8.4.3
External Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . 116
8.4.3.1
External Oscillator Amplifier . . . . . . . . . . . . . . . . . . . . . . 116
8.4.3.2
External Clock Input Path . . . . . . . . . . . . . . . . . . . . . . .117
8.4.4
Clock Monitor Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
8.4.4.1
Clock Monitor Reference Generator . . . . . . . . . . . . . . . 118
8.4.4.2
Internal Clock Activity Detector . . . . . . . . . . . . . . . . . . . 121
8.4.4.3
External Clock Activity Detector . . . . . . . . . . . . . . . . . . .121
8.4.5
Clock Selection Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
8.4.5.1
Clock Selection Switch. . . . . . . . . . . . . . . . . . . . . . . . . . 122
8.4.5.2
Clock Switching Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . 123
8.5
Usage Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
8.5.1
Switching Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . 125
8.5.2
Enabling the Clock Monitor . . . . . . . . . . . . . . . . . . . . . . . . 126
8.5.3
Clock Monitor Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
8.5.4
Quantization Error in DCO Output . . . . . . . . . . . . . . . . . . . 127
8.5.4.1
Digitally Controlled Oscillator . . . . . . . . . . . . . . . . . . . . . 128
8.5.4.2
Binary Weighted Divider . . . . . . . . . . . . . . . . . . . . . . . . 128
8.5.4.3
Variable-Delay Ring Oscillator . . . . . . . . . . . . . . . . . . . . 129
8.5.4.4
Ring Oscillator Fine-Adjust Circuit . . . . . . . . . . . . . . . . . 129
8.5.5
Switching Internal Clock Frequencies . . . . . . . . . . . . . . . . 130
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
109
Internal Clock Generator Module (ICG)
8.5.6
8.5.6.1
8.5.6.2
8.5.6.3
8.5.7
8.5.8
Nominal Frequency Settling Time . . . . . . . . . . . . . . . . . . . 131
Settling to Within 15 Percent . . . . . . . . . . . . . . . . . . . . . 131
Settling to Within 5 Percent . . . . . . . . . . . . . . . . . . . . . . 132
Total Settling Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Improving Settling Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Trimming Frequency on the Internal Clock Generator . . . . 135
8.6
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
8.6.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
8.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
8.7
Configuration Register Option . . . . . . . . . . . . . . . . . . . . . . . . 137
8.7.1
EXTSLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
8.8
I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
8.8.1
ICG Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
8.8.2
ICG Multiplier Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
8.8.3
ICG Trim Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
8.8.4
ICG DCO Divider Register . . . . . . . . . . . . . . . . . . . . . . . . . 145
8.8.5
ICG DCO Stage Register . . . . . . . . . . . . . . . . . . . . . . . . . . 146
8.2 Introduction
The internal clock generator module (ICG) is used to create a stable
clock source for the microcontroller without using any external
components. The ICG generates the oscillator output clock
(CGMXCLK), which is used by the COP, LVI, and other modules. The
ICG also generates the clock generator output (CGMOUT), which is fed
to the system integration module (SIM) to create the bus clocks. The bus
frequency will be one-fourth the frequency of CGMXCLK and one-half
the frequency of CGMOUT.
8.3 Features
The ICG has these features:
•
External clock generator, either 1-pin external source or 2-pin
crystal
•
Internal clock generator with programmable frequency output in
integer multiples of a nominal frequency (307.2 kHz ±25 percent)
Advance Information
110
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Functional Description
•
Frequency adjust (trim) register to improve variability to ±2 percent
•
Bus clock software selectable from either internal or external clock
•
Clock monitor for both internal and external clocks
8.4 Functional Description
The ICG, shown in Figure 8-1, contains these major submodules:
•
Clock enable circuit
•
Internal clock generator
•
External clock generator
•
Clock monitor circuit
•
Clock selection circuit
8.4.1 Clock Enable Circuit
The clock enable circuit is used to enable the internal clock (ICLK) or
external clock (ECLK). The clock enable circuit generates an ICG stop
(ICGSTOP) signal which stops all clocks (ICLK, ECLK, and the lowfrequency base clock, IBASE) low. ICGSTOP is set and the ICG is
disabled in stop mode.
The internal clock enable signal (ICGEN) turns on the internal clock
generator which generates ICLK. ICGEN is set (active) whenever the
ICGON bit is set and the ICGSTOP signal is clear. When ICGEN is clear,
ICLK and IBASE are both low.
The external clock enable signal (ECGEN) turns on the external clock
generator which generates ECLK. ECGEN is set (active) whenever the
ECGON bit is set and the ICGSTOP signal is clear. When ECGEN is
clear, ECLK is low.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
111
Internal Clock Generator Module (ICG)
CS
CGMOUT
RESET
CGMXCLK
CLOCK SELECTION
CIRCUIT
IOFF
EOFF
CMON
CPU_INT
CMF
ECGS
CLOCK
MONITOR/SWITCHER
CIRCUIT
ICGS
DDIV
INTERNAL CLOCK
GENERATOR
N[6:0]
DSTG
TRIM[7:0]
ICLK
IBASE
ICGEN
SIMOSCEN
CLOCK ENABLE CIRCUIT
ECGON
ICGON
ECGEN
EXTERNAL CLOCK
GENERATOR
EXTSLOW
INTERNAL
TO MCU
OSC1
ECLK
OSC2
EXTERNAL
NAME
CONFIGURATION REGISTER BIT
NAME
REGISTER BIT
NAME
TOP LEVEL SIGNAL
NAME
MODULE SIGNAL
Figure 8-1. ICG Module Block Diagram
Advance Information
112
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Functional Description
8.4.2 Internal Clock Generator
The internal clock generator, shown in Figure 8-2, creates a lowfrequency base clock (IBASE), which operates at a nominal frequency
(fNOM) of 307.2 kHz ±25 percent, and an internal clock (ICLK) which is
an integer multiple of IBASE. This multiple is the ICG multiplier factor
(N), which is programmed in the ICG multiplier register (ICGMR). The
internal clock generator is turned off and the output clocks (IBASE and
ICLK) are held low when the internal clock generator enable signal
(ICGEN) is clear.
The internal clock generator contains:
•
A digitally controlled oscillator
•
A modulo N divider
•
A frequency comparator, which contains voltage and current
references, a frequency to voltage converter, and comparators
•
A digital loop filter
ICGEN
VOLTAGE &
CURRENT
REFERENCES
++
DSTG[7:0]
+
DIGITAL
LOOP
FILTER
–
DDIV[3:0]
DIGITALLY
CONTROLLED
OSCILLATOR
ICLK
––
TRIM[7:0]
FREQUENCY
COMPARATOR
CLOCK GENERATOR
N[6:0]
MODULO
N
DIVIDER
IBASE
NAME
REGISTER BIT
NAME
MODULE SIGNAL
Figure 8-2. Internal Clock Generator Block Diagram
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
113
Internal Clock Generator Module (ICG)
8.4.2.1 Digitally Controlled Oscillator
The digitally controlled oscillator (DCO) is an inaccurate oscillator which
generates the internal clock (ICLK). The clock period of ICLK is
dependent on the digital loop filter outputs (DSTG[7:0] and DDIV[3:0]).
Because there is only a limited number of bits in DDIV and DSTG, the
precision of the output (ICLK) is restricted to a long-term precision of
approximately ±0.202 percent to ±0.368 percent when measured over
several cycles (of the desired frequency). Additionally, since the
propagation delays of the devices used in the DCO ring oscillator are a
measurable fraction of the bus clock period, reaching the long-term
precision may require alternately running faster and slower than desired,
making the worst case cycle-to-cycle frequency variation ±6.45 percent
to ±11.8 percent (of the desired frequency). The valid values of
DDIV:DSTG range from $000 to $9FF. For more information on the
quantization error in the DCO, see 8.5.4 Quantization Error in DCO
Output.
8.4.2.2 Modulo N Divider
The modulo N divider creates the low-frequency base clock (IBASE) by
dividing the internal clock (ICLK) by the ICG multiplier factor (N)
contained in the ICG multiplier register (ICGMR). When N is
programmed to a $01 or $00, the divider is disabled and ICLK is passed
through to IBASE undivided. When the internal clock generator is stable,
the frequency of IBASE will be equal to the nominal frequency (fNOM) of
307.2 kHz ±25 percent.
8.4.2.3 Frequency Comparator
The frequency comparator effectively compares the low-frequency base
clock (IBASE) to a nominal frequency, fNOM. First, the frequency
comparator converts IBASE to a voltage by charging a known capacitor
with a current reference for a period dependent on IBASE. This voltage
is compared to a voltage reference with comparators, whose outputs are
fed to the digital loop filter. The dependence of these outputs on the
capacitor size, current reference, and voltage reference causes up to
±25 percent error in fNOM.
Advance Information
114
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Functional Description
8.4.2.4 Digital Loop Filter
The digital loop filter (DLF) uses the outputs of the frequency comparator
to adjust the internal clock (ICLK) clock period. The DLF generates the
DCO divider control bits (DDIV[3:0]) and the DCO stage control bits
(DSTG[7:0]), which are fed to the DCO. The DLF first concatenates the
DDIV and DSTG registers (DDIV[3:0]:DSTG[7:0]) and then adds or
subtracts a value dependent on the relative error in the low-frequency
base clock’s period, as shown in Table 8-1. In some extreme error
conditions, such as operating at a VDD level which is out of specification,
the DLF may attempt to use a value above the maximum ($9FF) or
below the minimum ($000). In both cases, the value for DDIV will be
between $A and $F. In this range, the DDIV value will be interpreted the
same as $9 (the slowest condition). Recovering from this condition
requires subtracting (increasing frequency) in the normal fashion until
the value is again below $9FF (if the desired value is $9xx, the value may
settle at $Axx through $Fxx, an acceptable operating condition). If the
error is less than ±5 percent, the internal clock generator’s filter stable
indicator (FICGS) is set, indicating relative frequency accuracy to the
clock monitor.
Table 8-1. Correction Sizes from DLF to DCO
Frequency Error
of IBASE Compared
to fNOM
DDVI[3:0]:DSTG[7:0]
Correction
IBASE < 0.85 fNOM
–32 (–$020)
0.85 fNOM < IBASE
IBASE < 0.95 fNOM
–8 (–$008)
0.95 fNOM < IBASE
IBASE < fNOM
–1 (–$001)
fNOM < IBASE
IBASE < 1.05 fNOM
+1 (+$001)
1.05 fNOM < IBASE
IBASE < 1.15 fNOM
+8 (+$008)
1.15 fNOM < IBASE
+32 (+$020)
Current to New
DDIV[3:0]:DSTG[7:0]
Relative Correction
in DCO
Min
$xFF to $xDF
–2/31
–6.45%
Max
$x20 to $x00
–2/19
–10.5%
Min
$xFF to $xF7
–0.5/31
–1.61%
Max
$x08 to $x00
–0.5/17.5
–2.86%
Min
$xFF to $xFE
–0.0625/31
–0.202%
Max
$x01 to $x00
–0.0625/17.0625
–0.366%
Min
$xFE to $xFF
+0.0625/30.9375
+0.202%
Max
$x00 to $x01
+0.0625/17
+0.368%
Min
$xF7 to $xFF
+0.5/30.5
+1.64%
Max
$x00 to $x08
+0.5/17
+2.94%
Min
$xDF to $xFF
+2/29
+6.90%
Max
$x00 to $x20
+2/17
+11.8%
x: Maximum error is independent of value in DDIV[3:0]. DDIV increments or decrements when an addition to DSTG[7:0]
carries or borrows.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
115
Internal Clock Generator Module (ICG)
8.4.3 External Clock Generator
The ICG also provides for an external oscillator or clock source, if
desired. The external clock generator, shown in Figure 8-3, contains an
external oscillator amplifier and an external clock input path.
STOP
ECLK
INPUT PATH
ECGON
AMPLIFIER
EXTERNAL
CLOCK
GENERATOR
EXTSLOW
INTERNAL TO MCU
OSC1
OSC2
EXTERNAL
NAME
CONFIGURATION REGISTER BIT
NAME
TOP LEVEL SIGNAL
NAME
REGISTER BIT
NAME
MODULE SIGNAL
RB
RS*
*RS can be 0 (shorted) when used
with higher-frequency crystals.
Refer to manufacturer’s data.
X1
C1
C2
COMPONENTS REQUIRED FOR
EXTERNAL CRYSTAL USE ONLY
Figure 8-3. External Clock Generator Block Diagram
8.4.3.1 External Oscillator Amplifier
The external oscillator amplifier provides the gain required by an
external crystal connected in a Pierce oscillator configuration. The
amount of this gain is controlled by the slow external (EXTSLOW) bit in
the configuration register. When EXTSLOW is set, the amplifier gain is
reduced for operating low-frequency crystals (32 kHz to 100 kHz). When
EXTSLOW is clear, the amplifier gain will be sufficient for 1-MHz to
8-MHz crystals. EXTSLOW must be configured correctly for the given
crystal or the circuit may not operate.
Advance Information
116
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Functional Description
The amplifier is enabled when the ECGON bit is set and stop mode is
not enabled. When the amplifier is enabled, it will be connected between
the OSC1 and OSC2 pins. In its typical configuration, the external
oscillator requires five external components:
1. Crystal, X1
2. Fixed capacitor, C1
3. Tuning capacitor, C2 (can also be a fixed capacitor)
4. Feedback resistor, RB
5. Series resistor, RS (included in the diagram to follow strict Pierce
oscillator guidelines and may not be required for all ranges of
operation, especially with high frequency crystals). Refer to the
crystal manufacturer’s data for more information.
8.4.3.2 External Clock Input Path
The external clock input path is the means by which the microcontroller
uses an external clock source. The input to the path is the OSC1 pin and
the output is the external clock (ECLK). The path, which contains input
buffering, is enabled when the ECGON bit is set and stop mode is not
enabled.
8.4.4 Clock Monitor Circuit
The ICG contains a clock monitor circuit which, when enabled, will
continuously monitor both the external clock (ECLK) and the internal
clock (ICLK) to determine if either clock source has failed based on these
conditions:
•
Either ICLK or ECLK has stopped.
•
The frequency of IBASE < frequency EREF divided by 4
•
The frequency of ECLK < frequency of IREF divided by 4
Using the clock monitor requires both clocks to be active (ECGON and
ICGON are both set). To enable the clock monitor, both clocks must also
be stable (ECGS and ICGS both set). This is to prevent the use of the
clock monitor when a clock is first turned on and potentially unstable
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
117
Internal Clock Generator Module (ICG)
NOTE:
Although the clock monitor can be enabled only when the both clocks are
stable (ICGS or ECGS is set), the clock monitor will remain enabled if
one of the clocks goes unstable.
The clock monitor only works if the external slow (EXTSLOW) bit in the
configuration register is properly defined with respect to the external
frequency source.
The clock monitor circuit, shown in Figure 8-4, contains these blocks:
•
Clock monitor reference generator
•
Internal clock activity detector
•
External clock activity detector
8.4.4.1 Clock Monitor Reference Generator
The clock monitor uses a reference based on one clock source to
monitor the other clock source. The clock monitor reference generator
generates the external reference clock (EREF) based on the external
clock (ECLK) and the internal reference clock (IREF) based on the
internal clock (ICLK). To simplify the circuit, the low-frequency base
clock (IBASE) is used in place of ICLK because it always operates at or
near 307.2 kHz. For proper operation, EREF must be at least twice as
slow as IBASE and IREF must be at least twice as slow as ECLK.
To guarantee that IREF is slower than ECLK and EREF is slower than
IBASE, one of the signals is divided down. Which signal is divided and
by how much is determined by the external slow (EXTSLOW) bit in the
configuration register, according to the rules in Table 8-2. Note that each
signal (IBASE and ECLK) is always divided by four. A longer divider is
used on either IBASE or ECLK based on the EXTSLOW bit.
NOTE:
If EXTSLOW is not set according to the rules defined in Table 8-2, the
clock monitor could switch clock sources unexpectedly.
Advance Information
118
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Functional Description
CMON
IOFF
CMON
FICGS
IBASE
IBASE
ICGEN
ICGEN
IOFF
ICLK
ACTIVITY
DETECTOR
EREF
ICGS
IBASE
EREF
ICGS
ICGON
EXTXTALEN
EXTSLOW
EXTSLOW
ESTBCLK
ECGS
DIVIDER
ECGON
ECLK
IREF
STOP
ECGS
ESTBCLK
ECGS
IREF
ECGON
ECLK
ECGEN
ECLK
ECLK
CMON
ACTIVITY
DETECTOR
EOFF
EOFF
NAME
CONFIGURATION REGISTER BIT
NAME
REGISTER BIT
NAME
TOP LEVEL SIGNAL
NAME
MODULE SIGNAL
Figure 8-4. Clock Monitor Block Diagram
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
119
Internal Clock Generator Module (ICG)
ICGON
ECGON
ECGS
EXTSLOW
External
Frequency
EREF
Divider
Ratio
EREF
Frequency
ESTBCLK
Divider
Ratio
ESTBCLK
Frequency
IREF
Divider
Ratio
IREF
Frequency
Table 8-2. Clock Monitor Reference Divider Ratios
0
x
x
x
U
U
U
U
U
Off
0
x
0
0
x
0
Off
0
Off
0
U
U
x
0
x
Off
0
4096
(ECLK)
1.875 kHz
x
1*4
76.8 kHz
±25%
4096
(ECLK)
244 Hz
1*4
1.953 kHz
76.8 kHz
±25%
4096
(IBASE)
75 Hz
±25%
16*4
4.8 kHz
±25%
Min
x
x
x
x
1
1
30 kHz
Max
8 MHz
Min
1 MHz
0
1.953 kHz
128*4
Max
8 MHz
Min
30 kHz
1
15.63 kHz
7.5 kHz
1*4
Max
100 kHz
25.0 kHz
500 kHz
U: Unaffected. Refer to section of table where ICGON or ECGON is set to x (don’t care).
IBASE is always used as the internal frequency (307.2 kHz).
The long divider (divide by 4096) is also used as an external crystal
stabilization divider. The divider is reset when the external clock
generator is off (ECGEN is clear). When the external clock generator is
first turned on, the external clock generator stable bit (ECGS) will be
clear. This condition automatically selects ECLK as the input to the long
divider. The external stabilization clock (ESTBCLK) will be ECLK divided
by 4096. This timeout allows the crystal to stabilize. The falling edge of
ESTBCLK is used to set ECGS. (ECGS will set after a full 16 or 4096
cycles.) When ECGS is set, the divider returns to its normal function.
ESTBCLK may be generated by either IBASE or ECLK, but any clocking
will reinforce only the set condition. If ECGS is cleared because the clock
monitor determined that ECLK was inactive, the divider will revert to a
stabilization divider. Since this will change the EREF and IREF divide
ratios, it is important to turn the clock monitor off (CMON = 0) after
inactivity is detected to ensure valid recovery.
Advance Information
120
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Functional Description
8.4.4.2 Internal Clock Activity Detector
The internal clock activity detector looks for at least one falling edge on
the low-frequency base clock (IBASE) every time the external reference
(EREF) is low. Since EREF is less than half the frequency of IBASE, this
should occur every time. If it does not occur two consecutive times, the
internal clock inactivity indicator (IOFF) is set. IOFF will be cleared the
next time there is a falling edge of IBASE while EREF is low.
The internal clock stable bit (ICGS) is set when IBASE is within
approximately 5 percent of the target 307.2 kHz ±25 percent for two
consecutive measurements. ICGS is cleared when IBASE is outside the
5 percent of the target 307.2 kHz ±25 percent, the internal clock
generator is disabled (ICGEN is clear), or when IOFF is set.
8.4.4.3 External Clock Activity Detector
The external clock activity detector looks for at least one falling edge on
the external clock (ECLK) every time the internal reference (IREF) is low.
Since IREF is less than half the frequency of ECLK, this should occur
every time. If it does not occur two consecutive times, the external clock
inactivity indicator (EOFF) is set. EOFF will be cleared the next time
there is a falling edge of ECLK while IREF is low.
The external clock stable bit (ECGS) is also generated in the external
clock activity detector. ECGS is set on a falling edge of the external
stabilization clock (ESTBCLK). This will be 4096 ECLK cycles after the
external clock generator on bit (ECGON) is set. ECGS is cleared when
the external clock generator is disabled (ECGON is clear) or when EOFF
is set.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
121
Internal Clock Generator Module (ICG)
8.4.5 Clock Selection Circuit
The clock selection circuit, shown in Figure 8-5, contains two clock
switches which generate the oscillator output clock (CGMXCLK) from
either the internal clock (ICLK) or the external clock (ECLK). The clock
selection circuit also contains a divide-by-two circuit which creates the
clock generator output clock (CGMOUT), which generates the bus
clocks.
CS
SELECT
ICLK
ICLK
ECLK
ECLK
IOFF
IOFF
EOFF
EOFF
RESET
VSS
NAME
OUTPUT
SYNCHRONIZING
CLOCK
CGMXCLK
DIV2
SWITCHER
CGMOUT
FORCE_I
FORCE_E
TOP LEVEL SIGNAL
NAME
REGISTER BIT
NAME
MODULE SIGNAL
Figure 8-5. Clock Selection Circuit Block Diagram
8.4.5.1 Clock Selection Switch
The clock select switch creates the oscillator output clock (CGMXCLK)
from either the internal clock (ICLK) or the external clock (ECLK), based
on the clock select bit (CS; set selects ECLK, clear selects ICLK). When
switching the CS bit, both ICLK and ECLK must be on (ICGON and
ECGON set). The clock being switched to must also be stable (ICGS or
ECGS set).
Advance Information
122
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Functional Description
8.4.5.2 Clock Switching Circuit
To robustly switch between the internal clock (ICLK) and the external
clock (ECLK), the switch assumes the clocks are completely
asynchronous, so a synchronizing circuit is required to make the
transition (see Figure 8-6). When the clock select bit is changed, the
switch will continue to operate off the original clock for between 1 and 2
cycles as the select input transitions through one side of the
synchronizer. Next, the output will be held low for between 1 and 2
cycles of the new clock as the select input transitions through the other
side. Then the output starts switching at the new clock’s frequency. This
transition guarantees that no glitches will be seen on the output even
though the select input may change asynchronously to the clocks. The
unpredictably of the transition period is a necessary result of the
asynchronicity.
IOFF
D
Q
D
QB
CK
DFF
CK
Q
DFF
QB
ICLK
FORCE_I
OUTPUT
ECLK
CK
FORCE_E
QB
CK
DFF
D
SELECT
QB
DFF
Q
D
Q
EOFF
FORCE_I = Force internal; reset condition
FORCE_E = Force external
Figure 8-6. Synchronizing Clock Switcher Circuit Diagram
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
123
Internal Clock Generator Module (ICG)
The switch automatically selects ICLK during reset. When the clock
monitor is on (CMON is set) and it determines one of the clock sources
is inactive (as indicated by the IOFF or EOFF signals), the circuit is
forced to select the active clock. There are no clocks for the inactive side
of the synchronizer to properly operate, so that side is forced deselected.
However, the active side will not be selected until one to two clock cycles
after the IOFF or EOFF signal transitions.
8.5 Usage Notes
The ICG has several features which can provide protection to the
microcontroller if properly used. There are other features which can
greatly simplify usage of the ICG if certain techniques are employed.
This section will describe several possible ways to use the ICG and its
features. These techniques are not the only ways to use the ICG, and
may not be optimum for all environments. In any case, these techniques
should be used only as a template, and the user should modify them
according to the application’s requirements.
These notes include:
•
Switching clock sources
•
Enabling the clock monitor
•
Using clock monitor interrupts
•
Quantization error in DCO output
•
Switching internal clock frequencies
•
Nominal frequency settling time
•
Improving frequency settling time
•
Trimming frequency
Advance Information
124
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Usage Notes
8.5.1 Switching Clock Sources
Switching from one clock source to another requires both clock sources
to be enabled and stable. A simple flow requires:
1. Enable desired clock source
2. Wait for it to become stable
3. Switch clocks
4. Disable previous clock source
The key point to remember in this flow is that the clock source cannot be
switched (CS cannot be written) unless the desired clock is on and
stable.
A short assembly code example of how to employ this flow is shown in
Figure 8-7. This code is for illustrative purposes only and does not
represent valid syntax for any particular assembler.
start
lda
#$13
loop
**
**
sta
icgcr
cmpa
bne
icgcr
loop
;Clock Switching Code Example
;This code switches from Internal to External clock
;Clock Monitor and interrupts are not enabled
;Mask for CS, ECGON, ECGS
;If switching from External to Internal, mask is $0C.
;Other code here, such as writing the COP, since ECGS may
;take some time to set
;Try to set CS, ECGON and clear ICGON. ICGON will not
;clear until CS is set, and CS will not set until
;ECGON and ECGS are set.
;Check to see if ECGS set, then CS set, then ICGON clear
;Keep looping until ICGON is clear.
Figure 8-7. Code Example for Switching Clock Sources
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
125
Internal Clock Generator Module (ICG)
8.5.2 Enabling the Clock Monitor
Many applications require the clock monitor to determine if one of the
clock sources has become inactive, so the other can be used to recover
from a potentially dangerous situation. Using the clock monitor requires
both clocks to be active (ECGON and ICGON both set). To enable the
clock monitor, both clocks also must be stable (ECGS and ICGS both
set). This is to prevent the use of the clock monitor when a clock is first
turned on and potentially unstable.
Enabling the clock monitor and clock monitor interrupts requires a flow
similar to this flow:
1. Enable the alternate clock source
2. Wait for both clock sources to be stable
3. Switch to the desired clock source if necessary
4. Enable the clock monitor
5. Enable clock monitor interrupts
These events must happen in sequence. A short assembly code
example of how to employ this flow is shown in Figure 8-8. This code is
for illustrative purposes only and does not represent valid syntax for any
particular assembler.
start
lda
loop
**
sta
brset
cmpa
bne
;Clock Monitor Enabling Code Example
;This code turns on both clocks, selects the desired
; one, then turns on the Clock Monitor and Interrupts
#$AF
;Mask for CMIE, CMON, ICGON, ICGS, ECGON, ECGS
; If Internal Clock desired, mask is $AF
; If External Clock desired, mask is $BF
; If interrupts not desired mask is $2F int; $3F ext
**
;Other code here, such as writing the COP, since ECGS
; and ICGS may take some time to set.
icgcr
;Try to set CMIE. CMIE wont set until CMON set; CMON
; won’t set until ICGON, ICGS, ECGON, ECGS set.
6,ICGCR,error ;Verify CMF is not set
icgcr
;Check if ECGS set, then CMON set, then CMIE set
loop
;Keep looping until CMIE is set.
Figure 8-8. Code Example for Enabling the Clock Monitor
Advance Information
126
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Usage Notes
8.5.3 Clock Monitor Interrupts
The clock monitor circuit can be used to recover from perilous situations
such as crystal loss. To use the clock monitor effectively, these notes
should be observed:
•
Enable the clock monitor and clock monitor interrupts.
•
The first statement in the clock monitor interrupt service routine
should be a read to the ICG control register (ICGCR) to verify that
the clock monitor flag (CMF) is set. This is also the first step in
clearing the CMF bit.
•
Never use BSET or BCLR instructions on the ICGCR, as this may
inadvertently clear CMF. Only use the BRSET and BRCLR
instructions to check the CMF bit and not to check any other bits
in the ICGCR.
•
When the clock monitor detects inactivity on the selected clock
source (defined by the CS bit of the ICG control register), the
inactive clock is deselected automatically and the remaining active
clock is selected as the source for CGMXCLK. The interrupt
service routine can use the state of the CS bit to check which clock
is inactive.
•
When the clock monitor detects inactivity, the application may
have been subjected to extreme conditions which may have
affected other circuits. The clock monitor interrupt service routine
should take any appropriate precautions.
8.5.4 Quantization Error in DCO Output
The digitally controlled oscillator (DCO) is comprised of three major subblocks:
1. Binary weighted divider
2. Variable-delay ring oscillator
3. Ring oscillator fine-adjust circuit
Each of these blocks affects the clock period of the internal clock (ICLK).
Since these blocks are controlled by the digital loop filter (DLF) outputs
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
127
Internal Clock Generator Module (ICG)
DDIV and DSTG, the output of the DCO can change only in quantized
steps as the DLF increments or decrements its output. The following
sections describe how each block will affect the output frequency.
8.5.4.1 Digitally Controlled Oscillator
The digitally controlled oscillator (DCO) is an inaccurate oscillator which
generates the internal clock (ICLK), whose clock period is dependent on
the digital loop filter outputs (DSTG[7:0] and DDIV[3:0]). Because of the
digital nature of the DCO, the clock period of ICLK will change in
quantized steps. This will create a clock period difference or quantization
error (Q-ERR) from one cycle to the next. Over several cycles or for
longer periods, this error is divided out until it reaches a minimum error
of 0.202 percent to 0.368 percent. The dependence of this error on the
DDIV[3:0] value and the number of cycles the error is measured over is
shown in Table 8-3.
Table 8-3. Quantization Error in ICLK
DDIV[3:0]
ICLK Cycles
Bus Cycles
tICLK Q-ERR
%0000 (min)
4
1
1.61%–2.94%
%0000 (min)
≥ 32
≥8
0.202%–0.368%
%0001
4
1
0.806%–1.47%
%0001
≥ 16
≥4
0.202%–0.368%
%0010
4
1
0.403%–0.735%
%0010
≥8
≥2
0.202%–0.368%
%0011
≥4
≥1
0.202%–0.368%
%0100
≥2
≥1
0.202%–0.368%
%0101–%1001 (max)
≥1
≥1
0.202%–0.368%
8.5.4.2 Binary Weighted Divider
The binary weighted divider divides the output of the ring oscillator by a
power of 2, specified by the DCO divider control bits (DDIV[3:0]). DDIV
maximizes at %1001 (values of %1010 through %1111 are interpreted
as %1001), which corresponds to a divide by 512. When DDIV is %0000,
Advance Information
128
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Usage Notes
the ring oscillator’s output is divided by 1. Incrementing DDIV by 1 will
double the period; decrementing DDIV will halve the period. The DLF
cannot directly increment or decrement DDIV; DDIV is only incremented
or decremented when an addition or subtraction to DSTG carries or
borrows.
8.5.4.3 Variable-Delay Ring Oscillator
The variable-delay ring oscillator’s period is adjustable from 17 to 31
stage delays, in increments of two, based on the upper three DCO stage
control bits (DSTG[7:5]). A DSTG[7:5] of %000 corresponds to 17 stage
delays; DSTG[7:5] of %111 corresponds to 31 stage delays. Adjusting
the DSTG[5] bit has a 6.45 percent to 11.8 percent effect on the output
frequency. This also corresponds to the size correction made when the
frequency error is greater than ±15 percent. The value of the binary
weighted divider does not affect the relative change in output clock
period for a given change in DSTG[7:5].
8.5.4.4 Ring Oscillator Fine-Adjust Circuit
The ring oscillator fine-adjust circuit causes the ring oscillator to
effectively operate at non-integer numbers of stage delays by operating
at two different points for a variable number of cycles specified by the
lower five DCO stage control bits (DSTG[4:0]). For example, when
DSTG[7:5] is %011, the ring oscillator nominally operates at 23 stage
delays. When DSTG[4:0] is %00000, the ring will always operate at 23
stage delays. When DSTG[4:0] is %00001, the ring will operate at 25
stage delays for one of 32 cycles and at 23 stage delays for 31 of 32
cycles. Likewise, when DSTG[4:0] is %11111, the ring operates at 25
stage delays for 31 of 32 cycles and at 23 stage delays for one of 32
cycles. When DSTG[7:5] is %111, similar results are achieved by
including a variable divide-by-two, so the ring operates at 31 stages for
some cycles and at 17 stage delays, with a divide-by-two for an effective
34 stage delays, for the remainder of the cycles. Adjusting the DSTG[0]
bit has a 0.202 percent to 0.368 percent effect on the output clock period.
This corresponds to the minimum size correction made by the DLF, and
the inherent, long-term quantization error in the output frequency.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
129
Internal Clock Generator Module (ICG)
8.5.5 Switching Internal Clock Frequencies
The frequency of the internal clock (ICLK) may need to be changed for
some applications. For example, if the reset condition does not provide
the correct frequency, or if the clock is slowed down for a low-power
mode (or sped up after a low-power mode), the frequency must be
changed by programming the internal clock multiplier factor (N). The
frequency of ICLK is N times the frequency of IBASE, which is 307.2 kHz
±25 percent.
Before switching frequencies by changing the N value, the clock monitor
must be disabled. This is because when N is changed, the frequency of
the low-frequency base clock (IBASE) will change proportionally until the
digital loop filter has corrected the error. Since the clock monitor uses
IBASE, it could erroneously detect an inactive clock. The clock monitor
cannot be re-enabled until the internal clock is stable again (ICGS is set).
NOTE:
There is no hardware mechanism to prevent changing bus frequency
dynamically. Be careful when changing bus frequency and consider the
impact on the system.
This flow is an example of how to change the clock frequency:
1. Verify there is no clock monitor interrupt by reading the CMF bit.
2. Turn off the clock monitor.
3. If desired, switch to the external clock (see 8.5.1 Switching Clock
Sources).
4. Change the value of N.
5. Switch back to internal (see 8.5.1 Switching Clock Sources),
if desired.
6. Turn on the clock monitor (see 8.5.2 Enabling the Clock
Monitor), if desired.
Advance Information
130
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Usage Notes
8.5.6 Nominal Frequency Settling Time
Because the clock period of the internal clock (ICLK) is dependent on the
digital loop filter outputs (DDIV and DSTG) which cannot change
instantaneously, ICLK will temporarily operate at an incorrect clock
period when any of the operating condition changes. This happens
whenever the part is reset, the ICG multiply factor (N) is changed, the
ICG trim factor (TRIM) is changed, or the internal clock is enabled after
inactivity (STOP or disabled operation). The time that the ICLK takes to
adjust to the correct period is known as the settling time.
Settling time depends primarily on how many corrections it takes to
change the clock period, and the period of each correction. Since the
corrections require four periods of the low-frequency base clock
(4*tIBASE), and since ICLK is N (the ICG multiply factor for the desired
frequency) times faster than IBASE, each correction takes 4*N*tICLK.
The period of ICLK, however, will vary as the corrections occur.
8.5.6.1 Settling to Within 15 Percent
When the error is greater than 15 percent, the filter takes eight
corrections to double or halve the clock period. Due to how the DCO
increases or decreases the clock period, the total period of these eight
corrections is approximately 11 times the period of the fastest correction.
(If the corrections were perfectly linear, the total period would be 11.5
times the minimum period; however, the ring must be slightly non-linear.)
Therefore, the total time it takes to double or halve the clock period is
44*N*tICLKFAST.
If the clock period needs more than doubled or halved, the same
relationship applies, only for each time the clock period needs doubled,
the total number of cycles doubles.
That is, when transitioning from fast to slow:
•
Going from the initial speed to half speed takes 44*N*tICLKFAST
•
From half speed to quarter speed takes 88*N*tICLKFAST
•
Going from quarter speed to eighth speed takes 176*N*tICLKFAST,
and so on.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
131
Internal Clock Generator Module (ICG)
This series can be expressed as (2x–1)*44*N*tICLKFAST, where x is the
number of times the speed needs doubled or halved. Since 2x happens
to be equal to tICLKSLOW/tICLKFAST, the equation reduces to
44*N*(tICLKSLOW-tICLKFAST). Note that increasing speed takes much
longer than decreasing speed since N is higher. This can be expressed
in terms of the initial clock period (t1) minus the final clock period (t2) as
such:
t 15 = abs [ 44N ( t 1 – t 2 ) ]
8.5.6.2 Settling to Within 5 Percent
Once the clock period is within 15 percent of the desired clock period,
the filter starts making smaller adjustments. When between 15 percent
and 5 percent error, each correction will adjust the clock period between
1.61 percent and 2.94 percent. In this mode, a maximum of eight
corrections will be required to get to less than 5 percent error. Since the
clock period is relatively close to desired, each correction takes
approximately the same period of time, or 4*tIBASE. At this point, the
internal clock stable bit (ICGS) will be set and the clock frequency is
usable, although the error will be as high as 5 percent. The total time to
this point is:
t 5 = abs [ 44N ( t1 – t2 ) ] + 32tIBASE
8.5.6.3 Total Settling Time
Once the clock period is within 5 percent of the desired clock period, the
filter starts making minimum adjustments. In this mode, each correction
will adjust the frequency between 0.202 percent and 0.368 percent. A
maximum of 24 corrections will be required to get to the minimum error.
Each correction takes approximately the same period of time or 4*tIBASE.
Added to the corrections for 15 percent to 5 percent, this makes 32
corrections (128*tIBASE) to get from 15 percent to the minimum error.
The total time to the minimum error is:
t tot = abs [ 44N ( t1 – t 2 ) ] + 128tIBASE
Advance Information
132
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Usage Notes
The equations for t15, t5, and ttot are dependent on the actual initial and
final clock periods t1 and t2, not the nominal. This means the variability
in the ICLK frequency due to process, temperature, and voltage must be
considered. Additionally, other process factors and noise can affect the
actual tolerances of the points at which the filter changes modes. This
means a worst case adjustment of up to 35 percent (ICLK clock period
tolerance plus 10 percent) must be added. This adjustment can be
reduced with trimming. Table 8-4 shows some typical values for settling
time.
Table 8-4. Typical Settling Time Examples
t1
t2
N
t15
t5
ttot
1/ (6.45 MHz)
1/ (25.8 MHz)
84
430 µs
535 µs
850 µs
1/ (25.8 MHz)
1/ (6.45 MHz)
21
107 µs
212 µs
525 µs
1/ (25.8 MHz)
1/ (307.2 kHz)
1
141 µs
246 µs
560 µs
1/ (307.2 kHz)
1/ (25.8 MHz)
84
11.9 ms
12.0 ms
12.3 ms
8.5.7 Improving Settling Time
The settling time of the internal clock generator can be vastly improved
if an external clock source can be used during the settling time. When
the internal clock generator is disabled (ICGON is low), the DDIV[3:0]
and DSTG[7:0] bits can be written. Then, when the internal clock
generator is re-enabled, the clock period will automatically start at the
point written in the DDIV and DSTG bits.
Since a change in the DDIV and DSTG bits only cause a change in the
clock period relative to the starting point, the starting point must first be
captured. The initial clock period can be expressed as in the next
example, where tX is a process, temperature, and voltage dependent
constant and DDIV1 and DSTG1 are the values of DDIV and DSTG
when operating at t1.
t1 = tX ⋅ 2
DDIV1
MC68HC908RF2 — Rev. 1
MOTOROLA
⋅ DSTG1
Advance Information
Internal Clock Generator Module (ICG)
133
Internal Clock Generator Module (ICG)
Finding the new values for DDIV and DSTG is easy if the new clock
period is a binary multiple or fraction of the original. In this case, DSTG
is unchanged and DDIV2 is DDIV1 + log2(t2/t1).
If the new clock period is not a binary multiple or fraction of the original,
both DSTG and DDIV may need to change according to these
equations:
log ( t 2 ⁄ t 1 )
DVFACT = int --------------------------log ( 2 )
DDIV2 = DDIV1 + DVFACT
( t2 ⁄ t 1 )
DSFACT = ---------------------------------------------------( DDIV2 – DDIV1 )
2
DSTG2 = DSFACT ⋅ DSTG1
If DSTG2 is greater than 255:
DDIV2 = DDIV2 + 1
DSTG2
DSTG2 = --------------------2
The software required to do this is relatively simple, since most of the
math can be done before coding because the initial and final clock
periods are known. An example of how to code this in assembly code is
shown in Figure 8-9. This example is for illustrative purposes only and
does not represent a valid syntax for any particular assembler.
Advance Information
134
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Usage Notes
;DDIV and DSTG modification code example
;Changes DDIV and DSTG according to the initial and
; desired clock period values
;Requires ICGON to be clear (disabled)
;User must previously calculate DVFACT and STFACT by
; the equations listed in the specification
;Modifies X and A registers
start
store
exit
lda
cmp
lda
add
sta
lda
icgcr
#13
#dvfact
icgdvr
icgdvr
#stfact
ldx
mul
rola
rolx
bcc
rorx
inc
stx
lda
cmp
bhi
lda
sta
jmp
jmp
icgdsr
store
icgdsr
icgdvr
#09
exit
#09
icgdvr
error
enable
;Verify ICGON clear (this will require
; CMIE,CMF,CMON,ICGON,ICGS clear and CS,ECGON,ECGS set)
;Add the DDIV factor (calculated before
; coding by the DDIV2 equation)
;Load the DSTG factor (calculated before coding and
; multiplied by 128 to make it 0-255 for maximum precision
;Load current stage register contents
;Multiply factor times current value
;Since factor was multiplied by 128,
; result is x6-x0:a7, so put it all in X
;If result is >255, rolx will set carry
; so divide result by two and
; add one to DDIV
;Store value
;Test to see if DDIV too high or low
;Valid range 0-9; too low is FF/FE; too high is 0A/0B
;If DDIV is 0-9, you’re almost done
;Otherwise, maximize period and execute error code
;Jump to code which turns on desired
;clock, clock monitor, interrupts, etc.
Figure 8-9. Code Example for Writing DDIV and DSTG
8.5.8 Trimming Frequency on the Internal Clock Generator
The unadjusted frequency of the low-frequency base clock (IBASE),
when the comparators in the frequency comparator indicate zero error,
will vary as much as ±25 percent due to process, temperature, and
voltage dependencies. These dependencies are in the voltage and
current references, the offset of the comparators, and the internal
capacitor. The voltage and temperature dependencies have been
designed to be a maximum of approximately ±1 percent error. The
process dependencies account for the rest.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
135
Internal Clock Generator Module (ICG)
Fortunately, for an individual part, the process dependencies are
constant. An individual part can operate at approximately ±2 percent
variance from its unadjusted operating point over the entire specification
range of the application. If the unadjusted operating point can be
changed, the entire variance can be limited to ±2 percent.
The method of changing the unadjusted operating point is by changing
the size of the capacitor. This capacitor is designed with 639 equally
sized units, 384 of which are always connected. The remaining 255 units
are put in by adjusting the ICG trim factor (TRIM). The default value for
TRIM is $80, or 128 units, making the default capacitor size 512. Each
unit added or removed will adjust the output frequency by about ±0.195
percent of the unadjusted frequency (adding to TRIM will decrease
frequency). Therefore, the frequency of IBASE can be changed to ±25
percent of its unadjusted value, which is enough to cancel the process
variability mentioned before.
The best way to trim the internal clock is to use the timer to measure the
width of an input pulse on an input capture pin (this pulse must be
supplied by the application and should be as long or wide as possible).
Considering the prescale value of the timer and the theoretical (zero
error) frequency of the bus (307.2 kHz *N/4), the error can be calculated.
This error, expressed as a percentage, can be divided by 0.195 percent
and the resultant factor added or subtracted from TRIM. This process
should be repeated to eliminate any residual error.
NOTE:
It is recommended that the user preserve a copy of the contents of the
ICG trim register (ICGTR) in non-volitale memory.
Address $7FEF is reserved for an optional factory-determined value.
Consult with a local Motorola representative for more information and
availability of this option.
Advance Information
136
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
Low-Power Modes
8.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low powerconsumption standby modes.
8.6.1 Wait Mode
The ICG remains active in wait mode. If enabled, the ICG interrupt to the
CPU can bring the MCU out of wait mode.
In some applications, low-power consumption is desired in wait mode
and a high-frequency clock is not needed. In these applications, reduce
power consumption by either selecting a low-frequency external clock
and turning the internal clock generator off, or reducing the bus
frequency by minimizing the ICG multiplier factor (N) before executing
the WAIT instruction.
8.6.2 Stop Mode
The ICG is disabled in stop mode. Upon execution of the STOP
instruction, all ICG activity will cease and the output clocks (CGMXCLK
and CGMOUT) will be held low. Power consumption will be minimal.
The STOP instruction does not affect the values in the ICG registers.
Normal execution will resume after the MCU exits stop mode.
8.7 Configuration Register Option
One configuration register option affects the functionality of the ICG:
EXTSLOW (slow external clock).
All configuration register options will have a default setting. Refer to
Section 9. Configuration Register (CONFIG) on how the configuration
register is used.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
137
Internal Clock Generator Module (ICG)
8.7.1 EXTSLOW
Slow external clock (EXTSLOW), when set, will decrease the drive
strength of the oscillator amplifier, enabling low-frequency crystal
operation (30 kHz–100 kHz). When clear, EXTSLOW enables high
frequency crystal operation (1 MHz to 8 MHz).
EXTSLOW, when set, also configures the clock monitor to expect an
external clock source that is slower than the low-frequency base clock
(60 Hz–307.2 kHz). When EXTSLOW is clear, the clock monitor will
expect an external clock faster than the low-frequency base clock
(307.2 kHz–32 MHz).
The default state for this option is clear.
8.8 I/O Registers
The ICG contains five registers, summarized in Figure 8-10. These
registers are:
•
ICG control register, ICGCR
•
ICG multiplier register, ICGMR
•
ICG trim register, ICGTR
•
ICG DCO divider control register, ICGDVR
•
ICG DCO stage control register, ICGDSR
Several of the bits in these registers have interaction where the state of
one bit may force another bit to a particular state or prevent another bit
from being set or cleared. A summary of this interaction is shown in
Table 8-5.
Advance Information
138
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
I/O Registers
Addr.
$0036
$0037
$0038
Register Name
Bit 7
Internal Clock Generator Read:
Control Register
Write:
(ICGCR)
See page 141. Reset:
Internal Clock Generator Read:
Multiplier Register
Write:
(ICGMR)
See page 143. Reset:
Read:
Internal Clock Generator
Trim Register (ICGTR) Write:
See page 144.
Reset:
ICG DCO Divider Control
$0039
6
5
4
3
CMON
CS
ICGON
CMF
CMIE
2
1
ICGS
Bit 0
ECGS
ECGON
0
0
0
0
1
0
0
0
R
N6
N5
N4
N3
N2
N1
N0
0
0
0
1
0
1
0
1
TRIM7
TRIM6
TRIM5
TRIM4
TRIM3
TRIM2
TRIM1
TRIM0
1
0
0
0
0
0
0
0
R
R
R
R
DDIV3
DDIV2
DDIV1
DDIV0
0
0
0
0
U
U
U
U
DSTG6
DSTG5
DSTG4
DSTG3
DSTG2
DSTG1
DSTG0
Read:
Register (ICGDVR) Write:
See page 145.
Reset:
Read:
ICG DCO Stage Register
DSTG7
$003A
(ICGDSR) Write:
See page 146.
Reset:
Unaffected by reset
= Unimplemented
R
= Reserved
U = Unaffected
Figure 8-10. ICG I/O Register Summary
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
139
Internal Clock Generator Module (ICG)
Table 8-5. ICG Module Register Bit Interaction Summary
CMIE
CMF
CMON
CS
ICGON
ICGS
ECGON
ECGS
N[6:0]
TRIM[7:0]
DDIV[3:0]
DSTG[7:0]
Register Bit Results for Given Condition
Reset
0
0
0
0
1
0
0
0
$15
$80
—
—
CMF = 1
—
(1)
1
—
1
—
1
—
uw
uw
uw
uw
CMON = 0
0
0
(0)
—
—
—
—
—
—
—
—
—
CMON = 1
—
—
(1)
—
1
—
1
—
uw
uw
uw
uw
CS = 0
—
—
—
(0)
1
—
—
—
—
—
uw
uw
CS = 1
—
—
—
(1)
—
—
1
—
—
—
—
—
ICGON = 0
0
0
0
1
(0)
0
1
—
—
—
—
—
ICGON = 1
—
—
—
—
(1)
—
—
—
—
—
uw
uw
ICGS = 0
us
—
us
uc
—
(0)
—
—
—
—
—
—
ECGON = 0
0
0
0
0
1
—
(0)
0
—
—
uw
uw
ECGS = 0
us
—
us
us
—
—
—
(0)
—
—
—
—
IOFF = 1
—
1*
(1)
1
(1)
0
(1)
—
uw
uw
uw
uw
EOFF = 1
—
1*
(1)
0
(1)
—
(1)
0
uw
uw
uw
uw
N = written
(0)
(0)
(0)
—
—
0*
—
—
—
—
—
—
TRIM = written
(0)
(0)
(0)
—
—
0*
—
—
—
—
—
—
Condition
—
0, 1
0*, 1*
(0), (1)
us, uc, uw
Register bit is unaffected by the given condition.
Register bit is forced clear or set, respectively, in the given condition.
Register bit is temporarily forced clear or set, respectively, in the given condition.
Register bit must be clear or set, respectively, for the given condition to occur.
Register bit cannot be set, cleared, or written, respectively, in the given condition.
Advance Information
140
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
I/O Registers
8.8.1 ICG Control Register
The ICG control register (ICGCR) contains the control and status bits for
the internal clock generator, external clock generator, and clock monitor
as well as the clock select and interrupt enable bits.
Address: $0036
Bit 7
Read:
6
5
4
3
CMON
CS
ICGON
0
0
1
CMF
CMIE
2
1
ICGS
Bit 0
ECGS
ECGON
Write:
Reset:
0
0
0
0
0
= Unimplemented
Figure 8-11. ICG Control Register (ICGCR)
CMIE — Clock Monitor Interrupt Enable Bit
This read/write bit enables clock monitor interrupts. An interrupt will
occur when both CMIE and CMF are set. CMIE can be set when the
CMON bit has been set for at least one cycle. CMIE is forced clear
when CMON is clear or during reset.
1 = Clock monitor interrupts enabled
0 = Clock monitor interrupts disabled
CMF — Clock Monitor Interrupt Flag
This read-only bit is set when the clock monitor determines that either
ICLK or ECLK becomes inactive and the CMON bit is set. This bit is
cleared by first reading the bit while it is set, followed by writing the bit
low. This bit is forced clear when CMON is clear or during reset.
1 = Either ICLK or ECLK has become inactive.
0 = ICLK and ECLK have not become inactive since the last read
of the ICGCR or the clock monitor is disabled.
CMON — Clock Monitor On Bit
This read/write bit enables the clock monitor. CMON can be set when
both ICLK and ECLK have been on and stable for at least one bus
cycle (ICGON, ECGON, ICGS, and ECGS are all set). CMON is
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
141
Internal Clock Generator Module (ICG)
forced set when CMF is set, to avoid inadvertent clearing of CMF.
CMON is forced clear when either ICGON or ECGON is clear or
during reset.
1 = Clock monitor output enabled
0 = Clock monitor output disabled
CS — Clock Select Bit
This read/write bit determines which clock will generate the oscillator
output clock (CGMXCLK). This bit can be set when ECGON and
ECGS have been set for at least one bus cycle and can be cleared
when ICGON and ICGS have been set for at least one bus cycle. This
bit is forced set when the clock monitor determines the internal clock
(ICLK) is inactive or when ICGON is clear. This bit is forced clear
when the clock monitor determines that the external clock (ECLK) is
inactive, when ECGON is clear, or during reset.
1 = External clock (ECLK) sources CGMXCLK
0 = Internal clock (ICLK) sources CGMXCLK
ICGON — Internal Clock Generator On Bit
This read/write bit enables the internal clock generator. ICGON can
be cleared when the CS bit has been set and the CMON bit has been
clear for at least one bus cycle. ICGON is forced set when the CMON
bit is set, the CS bit is clear, or during reset.
1 = Internal clock generator enabled
0 = Internal clock generator disabled
ICGS — Internal Clock Generator Stable Bit
This read-only bit indicates when the internal clock generator has
determined that the internal clock (ICLK) is within about 5 percent of
the desired value. This bit is forced clear when the clock monitor
determines the ICLK is inactive, when ICGON is clear, when the ICG
multiplier factor is written, or during reset.
1 = Internal clock is within 5 percent of the desired value.
0 = Internal clock may not be within 5 percent of the desired value.
Advance Information
142
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
I/O Registers
ECGON — External Clock Generator On Bit
This read/write bit enables the external clock generator. ECGON can
be cleared when the CS and CMON bits have been clear for at least
one bus cycle. ECGON is forced set when the CMON bit or the CS bit
is set. ECGON is forced clear during reset.
1 = External clock generator enabled
0 = External clock generator disabled
ECGS — External Clock Generator Stable Bit
This read-only bit indicates when at least 4096 external clock (ECLK)
cycles have elapsed since the external clock generator was enabled.
This is not an assurance of the stability of ECLK but is meant to
provide a startup delay. This bit is forced clear when the clock monitor
determines ECLK is inactive, when ECGON is clear, or during reset.
1 = 4096 ECLK cycles have elapsed since ECGON was set.
0 = External cock is unstable, inactive, or disabled.
8.8.2 ICG Multiplier Register
Address: $0037
Bit 7
6
5
4
3
2
1
Bit 0
R
N6
N5
N4
N3
N2
N1
N0
0
0
0
1
0
1
0
1
R
= Reserved
Read:
Write:
Reset:
Figure 8-12. ICG Multiplier Register (ICGMR)
N6–N0 — ICG Multiplier Factor Bits
These read/write bits change the multiplier used by the internal
clock generator. The internal clock (ICLK) will be
(307.2 kHz ±25 percent) * N. A value of $00 in this register is
interpreted the same as a value of $01. This register cannot be written
when the CMON bit is set. Reset sets this factor to $15 (decimal 21)
for default frequency of 6.45 MHz ±25 percent (1.613 MHz ±25
percent bus).
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
143
Internal Clock Generator Module (ICG)
8.8.3 ICG Trim Register
Address: $0038
Bit 7
6
5
4
3
2
1
Bit 0
TRIM7
TRIM6
TRIM5
TRIM4
TRIM3
TRIM2
TRIM1
TRIM0
1
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 8-13. ICG Trim Register (ICGTR)
TRIM7–TRIM0 — ICG Trim Factor Bits
These read/write bits change the size of the internal capacitor used
by the internal clock generator. By testing the frequency of the internal
clock and incrementing or decrementing this factor accordingly, the
accuracy of the internal clock can be improved to ±2 percent.
Incrementing this register by 1 decreases the frequency by
0.195 percent of the unadjusted value. Decrementing this register by
one increases the frequency by 0.195 percent. This register cannot
be written when the CMON bit is set. Reset sets these bits to $80,
centering the range of possible adjustment.
NOTE:
It is recommended that the user preserve a copy of the contents of the
ICG trim register (ICGTR) in non-volitale memory.
Address $7FEF is reserved for an optional factory-determined ICG trim
value. Consult with a local Motorola representative for more information
and availability of this option.
Advance Information
144
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Internal Clock Generator Module (ICG)
I/O Registers
8.8.4 ICG DCO Divider Register
Address: $0039
Bit 7
6
5
4
3
2
1
Bit 0
R
R
R
R
DDIV3
DDIV2
DDIV1
DDIV0
0
0
0
0
U
U
U
U
Read:
Write:
Reset:
R
= Reserved
U = Unaffected
Figure 8-14. ICG DCO Divider Register (ICGDVR)
DDIV3–DDIV0 — ICG DCO Divider Control Bits
These bits indicate the number of divide-by-twos (DDIV) that follow
the digitally controlled oscillator. Incrementing DDIV will add another
divide-by-two, doubling the period (halving the frequency).
Decrementing has the opposite effect. DDIV cannot be written when
ICGON is set to prevent inadvertent frequency shifting. When ICGON
is set, DDIV is controlled by the digital loop filter. The range of valid
values for DDIV is from $0 to $9. Values of $A–$F are interpreted the
same as $9. Since the DCO is active during reset, reset has no effect
on DSTG and the value may vary.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Internal Clock Generator Module (ICG)
145
Internal Clock Generator Module (ICG)
8.8.5 ICG DCO Stage Register
Address: $003A
Bit 7
6
5
4
3
2
1
Bit 0
DSTG7
DSTG6
DSTG5
DSTG4
DSTG3
DSTG2
DSTG1
DSTG0
Read:
Write:
Reset:
Unaffected by reset
Figure 8-15. ICG DCO Stage Register (ICGDSR)
DSTG7–DSTG0 — ICG DCO Stage Control Bits
These bits indicate the number of stages DSTG (above the minimum)
in the digitally controlled oscillator. The total number of stages is
approximately equal to $1FF, so changing DSTG from $00 to $FF will
approximately double the period. Incrementing DSTG will increase
the period (decrease the frequency) by 0.202 percent to 0.368
percent (decrementing has the opposite effect). DSTG cannot be
written when ICGON is set to prevent inadvertent frequency shifting.
When ICGON is set, DSTG is controlled by the digital loop filter. Since
the DCO is active during reset, reset has no effect on DSTG and the
value may vary.
Advance Information
146
MC68HC908RF2 — Rev. 1
Internal Clock Generator Module (ICG)
MOTOROLA
Advance Information — MC68HC908RF2
Section 9. Configuration Register (CONFIG)
9.1 Contents
9.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
9.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
9.2 Introduction
This section describes the configuration register (CONFIG). The
configuration register enables or disables these options:
•
Stop mode recovery time (32 CGMXCLK cycles or 4,096
CGMXCLK cycles)
•
COP timeout period (218 – 24 or 213 – 24 CGMXCLK cycles)
•
STOP instruction
•
Computer operating properly module (COP)
•
Low-voltage inhibit (LVI) module control
9.3 Functional Description
The CONFIG register is used in the initialization of various options and
can be written once after each reset. The register is set to the
documented value during reset. Since the various options affect the
operation of the MCU, it is recommended that these registers be written
immediately after reset. The configuration register is located at $001F.
NOTE:
On a FLASH device, the options are one-time writable by the user after
each reset. The CONFIG register is not in the FLASH memory but is a
special register containing one-time writable latches after each reset.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Configuration Register (CONFIG)
147
Configuration Register (CONFIG)
Upon a reset, the CONFIG register defaults to predetermined settings as
shown in Figure 2-1. Memory Map.
Address: $001F
BIt 7
6
5
4
3
2
1
Bit 0
LVIRST
LVIPWR
COPRS
SSREC
STOP
COPD
1
1
0
0
0
0
Read:
EXTSLOW LVISTOP
Write:
Reset:
0
0
Figure 9-1. Configuration Register (CONFIG)
EXTSLOW — Slow External Crystal Enable Bit
The EXTSLOW bit has two functions. It configures the ICG module for
a fast (1 MHz–8 MHz) or slow (30 kHz–100 kHz) speed crystal. The
option also configures the clock monitor operation in the ICG module
to expect an external frequency higher (307.2 kHz–32 MHz) or lower
(60 Hz–307.2 kHz) than the base frequency of the internal oscillator.
(See Section 8. Internal Clock Generator Module (ICG).)
1 = ICG set for slow external crystal operation
0 = ICG set for fast external crystal operation
LVISTOP — LVI Enable in Stop Mode Bit
When the LVIPWR bit is set, setting the LVISTOP bit enables the LVI
to operate during stop mode. Reset clears LVISTOP.
1 = LVI enabled during stop mode
0 = LVI disabled during stop mode
LVIRST — LVI Reset Enable Bit
LVIRST enables the reset signal from the LVI module.
(See Section 12. Low-Voltage Inhibit (LVI).)
1 = LVI module resets enabled
0 = LVI module resets disabled
LVIPWR — LVI Power Enable Bit
LVIPWR disables the LVI module. (See Section 12. Low-Voltage
Inhibit (LVI).)
1 = LVI module power enabled
0 = LVI module power disabled
Advance Information
148
MC68HC908RF2 — Rev. 1
Configuration Register (CONFIG)
MOTOROLA
Configuration Register (CONFIG)
Functional Description
COPRS — COP Rate Select Bit
COPRS selects the COP timeout period. Reset clears COPRS. (See
Section 11. Computer Operating Properly Module (COP).)
1 = COP timeout period = 213 – 24 CGMXCLK cycles
0 = COP timeout period = 218 – 24 CGMXCLK cycles
SSREC — Short Stop Recovery Bit
SSREC enables the CPU to exit stop mode with a delay of 32
CGMXCLK cycles instead of a 4096-CGMXCLK cycle delay.
1 = Stop mode recovery after 32 CGMXCLK cycles
0 = Stop mode recovery after 4096 CGMXCLK cycles
NOTE:
Exiting stop mode by pulling reset will result in the long stop recovery.
If using the internal clock generator module or an external crystal
oscillator, do not set the SSREC bit.
The LVI has an enable time of ten. The system stabilization time for
power-on reset and long stop recovery (both 4096 CGMXCLK cycles)
gives a delay longer than the LVI enable time for these startup scenarios.
There is no period where the MCU is not protected from a low-power
condition. However, when using the short stop recovery configuration
option, the 32 CGMXCLK delay must be greater than the LVI’s turn on
time to avoid a period in startup where the LVI is not protecting the MCU.
STOP — STOP Instruction Enable Bit
STOP enables the STOP instruction.
1 = STOP instruction enabled
0 = STOP instruction treated as illegal opcode
COPD — COP Disable Bit
COPD disables the COP module. (See Section 11. Computer
Operating Properly Module (COP).)
1 = COP module disabled
0 = COP module enabled
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Configuration Register (CONFIG)
149
Configuration Register (CONFIG)
Advance Information
150
MC68HC908RF2 — Rev. 1
Configuration Register (CONFIG)
MOTOROLA
Advance Information — MC68HC908RF2
Section 10. Monitor Read-Only Memory (MON)
10.1 Contents
10.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
10.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
10.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
10.4.1 Monitor Mode Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
10.4.2 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
10.4.3 Echoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
10.4.4 Break Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
10.4.5 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
10.4.6 Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
10.4.7 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
10.2 Introduction
This section describes the monitor read-only memory (MON). The MON
allows complete testing of the MCU through a single-wire interface with
a host computer.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Monitor Read-Only Memory (MON)
151
Monitor Read-Only Memory (MON)
10.3 Features
Features of the monitor ROM include:
•
Normal user-mode pin functionality
•
One pin dedicated to serial communication between monitor ROM
and host computer
•
Standard mark/space non-return-to-zero (NRZ) communication
with host computer
•
9600 baud communication with host computer when using a
9.8304-MHz crystal
•
Execution of code in random-access memory (RAM) or FLASH
•
FLASH security
•
FLASH programming
10.4 Functional Description
Monitor ROM receives and executes commands from a host computer.
Figure 10-1 shows a sample circuit used to enter monitor mode and
communicate with a host computer via a standard RS-232 interface.
While simple monitor commands can access any memory address, the
MC68HC908RF2 has a FLASH security feature to prevent external
viewing of the contents of FLASH. Proper procedures must be followed
to verify FLASH content. Access to the FLASH is denied to unauthorized
users of customer-specified software (see 10.4.7 Security).
In monitor mode, the MCU can execute host-computer code in RAM
while all MCU pins except PTA0 retain normal operating mode functions.
All communication between the host computer and the MCU is through
the PTA0 pin. A level-shifting and multiplexing interface is required
between PTA0 and the host computer. PTA0 is used in a wired-OR
configuration and requires a pullup resistor.
Advance Information
152
MC68HC908RF2 — Rev. 1
Monitor Read-Only Memory (MON)
MOTOROLA
Monitor Read-Only Memory (MON)
Functional Description
VDD
68HC908RK2
10 kΩ
RST
0.1 µF
VHI
10 kΩ
IRQ1
1
10 µF
+
3
4
10 µF
MC145407
20
+
OSC1
20 pF
17
+
+
10 µF
18
2
19
DB-25
2
5
16
3
6
15
10 µF
X1
9.8304 MHz
10 MΩ
OSC2
VDD
20 pF
VSS
VDD
VDD
0.1 µF
7
VDD
1
MC74HC125
14
2
3
6
5
VDD
10 kΩ
PTA0
4
VDD
7
10 kΩ
10 kΩ
PTB0
PTB2
Figure 10-1. Monitor Mode Circuit
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Monitor Read-Only Memory (MON)
153
Monitor Read-Only Memory (MON)
10.4.1 Monitor Mode Entry
Table 10-1 shows the pin conditions for entering monitor mode.
IRQ Pin
PTB0 Pin
PTB2 Pin
PTA0 Pin
Table 10-1. Monitor Mode Entry
CGMOUT(2)
VHI(1)
1
0
1
CGMXCLK
----------------------------2
Bus
Frequency
CGMOUT
-------------------------2
1. For V HI, see 17.7 3.0-Volt DC Electrical Characteristics Excluding UHF Module and
17.3 Absolute Maximum Ratings.
2. If the high voltage (VHI) is removed from the IRQ1 pin while in monitor mode, the clock
select bit (CS) controls the source of CGMOUT.
Enter monitor mode by either:
NOTE:
•
Executing a software interrupt instruction (SWI), or
•
Applying a logic 0 and then a logic 1 to the RST pin
Upon entering monitor mode, an interrupt stack frame plus a stacked H
register will leave the stack pointer at address $00F9.
Once out of reset, the MCU waits for the host to send eight security bytes
(see 10.4.7 Security). After the security bytes, the MCU sends a break
signal (10 consecutive logic 0s) to the host computer, indicating that it is
ready to receive a command.
Monitor mode uses alternate vectors for reset, SWI, and break interrupt.
The alternate vectors are in the $FE page instead of the $FF page and
allow code execution from the internal monitor firmware instead of user
code. The COP module is disabled in monitor mode as long as VHI (see
Section 17. Preliminary Electrical Specifications) is applied to either
the IRQ1 pin or the RST pin. (See Section 6. System Integration
Module (SIM) for more information on modes of operation.) The ICG
module is bypassed in monitor mode as long as VHI is applied to the
IRQ1 pin. RST does not affect the ICG.
Advance Information
154
MC68HC908RF2 — Rev. 1
Monitor Read-Only Memory (MON)
MOTOROLA
Monitor Read-Only Memory (MON)
Functional Description
Table 10-2 is a summary of the differences between user mode and
monitor mode.
Table 10-2. Mode Differences
Functions
Modes
COP
Reset
Vector
High
Reset
Vector
Low
Break
Vector
High
Break
Vector
Low
SWI
Vector
High
SWI
Vector
Low
User
Enabled
$FFFE
$FFFF
$FFFC
$FFFD
$FFFC
$FFFD
Monitor
Disabled(1)
$FEFE
$FEFF
$FEFC
$FEFD
$FEFC
$FEFD
1. If the high voltage (VHI) is removed from the IRQ1 pin while in monitor mode, the SIM
asserts its COP enable output. The COP is a mask option enabled or disabled by the
COPD bit in the configuration register. See 17.7 3.0-Volt DC Electrical Characteristics
Excluding UHF Module.
10.4.2 Data Format
Communication with the monitor ROM is in standard non-return-to-zero
(NRZ) mark/space data format. (See Figure 10-2 and Figure 10-3.)
The data transmit and receive rate is determined by the crystal. Transmit
and receive baud rates must be identical.
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
STOP
BIT
NEXT
START
BIT
1, 2, 3
Notes: 1 = Echo delay (2 bit times)
2 = Data return delay (2 bit times)
3 = Wait 1 bit time before sending next byte.
Figure 10-2. Monitor Data Format
$A5
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
STOP
BIT
NEXT
START
BIT
1, 2, 3
BREAK
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
Notes: 1 = Echo delay (2 bit times)
2 = Data return delay (2 bit times)
3 = Wait 1 bit time before sending next byte.
STOP
BIT
NEXT
START
BIT
1, 2, 3
Figure 10-3. Sample Monitor Waveforms
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Monitor Read-Only Memory (MON)
155
Monitor Read-Only Memory (MON)
10.4.3 Echoing
As shown in Figure 10-4, the monitor ROM immediately echoes each
received byte back to the PTA0 pin for error checking.
Any result of a command appears after the echo of the last byte of the
command.
SENT TO
MONITOR
READ
READ
ADDR. HIGH
1
3
ADDR. HIGH
1
ADDR. LOW
3
ADDR. LOW
1
DATA
2
ECHO
RESULT
Notes: 1 = Echo delay (2 bit times)
2 = Data return delay (2 bit times)
3 = Wait 1 bit time before sending next byte.
Figure 10-4. Read Transaction
10.4.4 Break Signal
A start bit followed by nine low bits is a break signal. (See Figure 10-5.)
When the monitor receives a break signal, it drives the PTA0 pin high for
the duration of two bits before echoing the break signal.
MISSING STOP BIT
2-STOP-BIT DELAY BEFORE ZERO ECHO
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Figure 10-5. Break Transaction
Advance Information
156
MC68HC908RF2 — Rev. 1
Monitor Read-Only Memory (MON)
MOTOROLA
Monitor Read-Only Memory (MON)
Functional Description
10.4.5 Commands
The monitor ROM uses these commands:
•
READ, read memory
•
WRITE, write memory
•
IREAD, indexed read
•
IWRITE, indexed write
•
READSP, read stack pointer
•
RUN, run user program
A sequence of IREAD or IWRITE commands can access a block of
memory sequentially over the full 64-Kbyte memory map.
Table 10-3. READ (Read Memory) Command
Description
Read byte from memory
Operand
Specifies 2-byte address in high byte:low byte order
Data Returned
Returns contents of specified address
Opcode
$4A
Command Sequence
SENT TO
MONITOR
READ
READ
1
ADDR. HIGH
3
ADDR. HIGH
1
ADDR. LOW
3
ECHO
ADDR. LOW
1
DATA
2
RESULT
Notes: 1 = Echo delay (2 bit times)
2 = Data return delay (2 bit times)
3 = Wait 1 bit time before sending next byte.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Monitor Read-Only Memory (MON)
157
Monitor Read-Only Memory (MON)
Table 10-4. WRITE (Write Memory) Command
Description
Write byte to memory
Operand
Specifies 2-byte address in high byte:low byte order; low byte followed by data byte
Data Returned
None
Opcode
$49
Command Sequence
SENT TO
MONITOR
WRITE
WRITE
1
ADDR. HIGH
2
ADDR. HIGH
1
ADDR. LOW
2
ADDR. LOW
DATA
1
2
DATA
1
ECHO
Notes: 1 = Echo delay (2 bit times)
2 = Wait 1 bit time before sending next byte.
Table 10-5. IREAD (Indexed Read) Command
Description
Read next 2 bytes in memory from last address accessed
Operand
Specifies 2-byte address in high byte:low byte order
Data Returned
Returns contents of next two addresses
Opcode
$1A
Command Sequence
SENT TO
MONITOR
IREAD
IREAD
1
DATA
2
DATA
2
RESULT
ECHO
Notes: 1 = Echo delay (2 bit times)
2 = Data return delay (2 bit times)
Advance Information
158
MC68HC908RF2 — Rev. 1
Monitor Read-Only Memory (MON)
MOTOROLA
Monitor Read-Only Memory (MON)
Functional Description
Table 10-6. IWRITE (Indexed Write) Command
Description
Write to last address accessed + 1
Operand
Specifies single data byte
Data Returned
None
Opcode
$19
Command Sequence
SENT TO
MONITOR
IWRITE
IWRITE
1
DATA
DATA
2
1
ECHO
Notes: 1 = Echo delay (2 bit times)
2 = Wait 1 bit time before sending next byte.
Table 10-7. READSP (Read Stack Pointer) Command
Description
Reads stack pointer
Operand
None
Data Returned
Returns stack pointer plus one in high byte:low byte order. The plus one is due to the
use of the TSX instruction.
Opcode
$0C
Command Sequence
SENT TO
MONITOR
READSP
READSP
1
SP HIGH
2
SP LOW
2
RESULT
ECHO
Notes: 1 = Echo delay (2 bit times)
2 = Data return delay (2 bit times)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Monitor Read-Only Memory (MON)
159
Monitor Read-Only Memory (MON)
Table 10-8. RUN (Run User Program) Command
Description
Executes RTI instruction
Operand
None
Data Returned
None
Opcode
$28
Command Sequence
SENT TO
MONITOR
RUN
RUN
1
ECHO
Note 1 = Echo delay (2 bit times)
10.4.6 Baud Rate
With a 9.8304-MHz crystal, data is transferred between the monitor and
host at 9600 baud. If a 14.7456-MHz crystal is used, the monitor baud
rate is 14400.
NOTE:
While in monitor mode with VHI applied to IRQ1, the MCU bus clock is
always driven from the external clock.
10.4.7 Security
A security feature discourages unauthorized reading of FLASH locations
while in monitor mode. The host can bypass the security feature at
monitor mode entry by sending eight consecutive security bytes that
match the bytes at locations $FFF6–$FFFD. Locations $FFF6–$FFFD
contain user-defined data.
NOTE:
Do not leave locations $FFF6–$FFFD blank. For security reasons,
program locations $FFF6–$FFFD even if they are not used for vectors.
If FLASH is unprogrammed, the eight security byte values to be sent are
$00, the unprogrammed state of the FLASH.
During monitor mode entry, the MCU waits after the power-on reset for
the host to send the eight security bytes on pin PA0.
Advance Information
160
MC68HC908RF2 — Rev. 1
Monitor Read-Only Memory (MON)
MOTOROLA
Monitor Read-Only Memory (MON)
Functional Description
IRQ1
SEE NOTE
VDD
4096 + 32 CGMXCLK CYCLES
RST
24 CGMXCLK CYCLES
COMMAND
BYTE 8
$FFFD
BYTE 2
$FFF7
BYTE 1
$FFF6
Note: Any delay between rising IRQ1 and rising VDD will guarantee that the MCU bus is driven by the external clock.
FROM HOST
PA0
3
BYTE 8 ECHO
2
1
COMMAND ECHO
1
BREAK
1
BYTE 2 ECHO
FROM MCU
3
1
BYTE 1 ECHO
256 CGMXCLK CYCLES
ONE BIT TIME
Notes: 1 = Echo delay (2 bit times)
2 = Data return delay (2 bit times)
3 = Wait 1 bit time before sending next byte.
Figure 10-6. Monitor Mode Entry Timing
If the received bytes match those at locations $FFF6–$FFFD, the host
bypasses the security feature and can read all FLASH locations and
execute code from FLASH. Security remains bypassed until a power-on
reset occurs. After the host bypasses security, any reset other than a
power-on reset requires the host to send another eight bytes, but
security remains bypassed regardless of the data that the host sends.
If the received bytes do not match the data at locations $FFF6–$FFFD,
the host fails to bypass the security feature. The MCU remains in monitor
mode, but reading FLASH locations returns undefined data, and trying
to execute code from FLASH causes an illegal address reset. After the
host fails to bypass security, any reset other than a power-on reset
causes an endless loop of illegal address resets.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Monitor Read-Only Memory (MON)
161
Monitor Read-Only Memory (MON)
After receiving the eight security bytes from the host, the MCU transmits
a break character signalling that it is ready to receive a command.
NOTE:
The MCU does not transmit a break character until after the host sends
the eight security bytes.
Advance Information
162
MC68HC908RF2 — Rev. 1
Monitor Read-Only Memory (MON)
MOTOROLA
Advance Information — MC68HC908RF2
Section 11. Computer Operating Properly Module (COP)
11.1 Contents
11.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
11.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
11.4 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
11.4.1 CGMXCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
11.4.2 STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
11.4.3 COPCTL Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.4.4 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
11.4.5 Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.4.6 Reset Vector Fetch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.4.7 COPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.4.8 COPRS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
11.5
COP Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
11.6
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
11.7
Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
11.8 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
11.8.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
11.8.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168
11.9
COP Module During Break Interrupts . . . . . . . . . . . . . . . . . . .168
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Computer Operating Properly Module (COP)
163
Computer Operating Properly Module (COP)
11.2 Introduction
The computer operating properly (COP) module contains a free-running
counter that generates a reset if allowed to overflow. The COP module
helps software recover from runaway code. Prevent a COP reset by
periodically clearing the COP counter.
11.3 Functional Description
12-BIT COP PRESCALER
CLEAR STAGES 5–12
STOP INSTRUCTION
INTERNAL RESET SOURCES
RESET VECTOR FETCH
CLEAR ALL STAGES
CGMXCLK
COPCTL WRITE
RESET
RESET STATUS
REGISTER
6-BIT COP COUNTER
COPD FROM CONFIG
RESET
COPCTL WRITE
CLEAR COP
COUNTER
COPRS FROM CONFIG
Figure 11-1. COP Block Diagram
Advance Information
164
MC68HC908RF2 — Rev. 1
Computer Operating Properly Module (COP)
MOTOROLA
Computer Operating Properly Module (COP)
I/O Signals
The COP counter is a free-running 6-bit counter preceded by a 12-bit
prescaler. If not cleared by software, the COP counter overflows and
generates an asynchronous reset after 213 – 24 or 218 – 24 CGMXCLK
cycles, depending on the state of the COP rate select bit, COPRS, in the
configuration register. When COPRS = 1, a 4.9152-MHz crystal gives a
COP timeout period of 53.3 ms. Writing any value to location $FFFF
before an overflow occurs prevents a COP reset by clearing the COP
counter and stages 5 through 12 of the prescaler.
NOTE:
Service the COP immediately after reset and before entering or after
exiting stop mode to guarantee the maximum time before the first COP
counter overflow.
A COP reset pulls the RST pin low for 32 CGMXCLK cycles and sets the
COP bit in the SIM reset status register (SRSR).
In monitor mode, the COP is disabled if the RST pin or the IRQ1 pin is
held at VHI. During the break state, VHI on the RST pin disables the COP.
NOTE:
Place COP clearing instructions in the main program and not in an
interrupt subroutine. Such an interrupt subroutine could keep the COP
from generating a reset even while the main program is not working
properly.
11.4 I/O Signals
The following paragraphs describe the signals shown in Figure 11-1.
11.4.1 CGMXCLK
CGMXCLK is the oscillator output signal. See 8.4.5 Clock Selection
Circuit for a description of CGMXCLK.
11.4.2 STOP Instruction
The STOP instruction clears the COP prescaler.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Computer Operating Properly Module (COP)
165
Computer Operating Properly Module (COP)
11.4.3 COPCTL Write
Writing any value to the COP control register (COPCTL) (see 11.5 COP
Control Register) clears the COP counter and clears stages 12 through
5 of the COP prescaler. Reading the COP control register returns the
reset vector.
11.4.4 Power-On Reset
The power-on reset (POR) circuit clears the COP prescaler 4096
CGMXCLK cycles after power-up.
11.4.5 Internal Reset
An internal reset clears the COP prescaler and the COP counter.
11.4.6 Reset Vector Fetch
A reset vector fetch occurs when the vector address appears on the data
bus. A reset vector fetch clears the COP prescaler.
11.4.7 COPD
The COPD signal reflects the state of the COP disable bit (COPD) in the
configuration register. (See Section 9. Configuration Register
(CONFIG)).
11.4.8 COPRS
The COPRS signal reflects the state of the COP rate select bit (COPRS)
in the configuration register. (See Section 9. Configuration Register
(CONFIG)).
Advance Information
166
MC68HC908RF2 — Rev. 1
Computer Operating Properly Module (COP)
MOTOROLA
Computer Operating Properly Module (COP)
COP Control Register
11.5 COP Control Register
The COP control register is located at address $FFFF and overlaps the
reset vector. Writing any value to $FFFF clears the COP counter and
starts a new timeout period. Reading location $FFFF returns the low
byte of the reset vector.
Address: $FFFF
Bit 7
6
5
4
3
Read:
Low byte of reset vector
Write:
Clear COP counter
Reset:
Unaffected by reset
2
1
Bit 0
Figure 11-2. COP Control Register (COPCTL)
11.6 Interrupts
The COP does not generate CPU interrupt requests.
11.7 Monitor Mode
The COP is disabled in monitor mode when VHI is present on the IRQ1
pin or on the RST pin.
11.8 Low-Power Modes
The WAIT and STOP instructions put the MCU in low powerconsumption standby modes.
11.8.1 Wait Mode
The COP remains active in wait mode. To prevent a COP reset during
wait mode, periodically clear the COP counter in a CPU interrupt routine.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Computer Operating Properly Module (COP)
167
Computer Operating Properly Module (COP)
11.8.2 Stop Mode
Stop mode turns off the CGMXCLK input to the COP and clears the COP
prescaler. Service the COP immediately before entering or after exiting
stop mode to ensure a full COP timeout period after entering or exiting
stop mode.
The STOP bit (see Section 9. Configuration Register (CONFIG))
enables the STOP instruction. To prevent inadvertently turning off the
COP with a STOP instruction, disable the STOP instruction by clearing
the STOP bit.
11.9 COP Module During Break Interrupts
The COP is disabled during a break interrupt when VHI is present on the
RST pin.
Advance Information
168
MC68HC908RF2 — Rev. 1
Computer Operating Properly Module (COP)
MOTOROLA
Advance Information — MC68HC908RF2
Section 12. Low-Voltage Inhibit (LVI)
12.1 Contents
12.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
12.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
12.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
12.4.1 False Trip Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
12.4.2 Short Stop Recovery Option. . . . . . . . . . . . . . . . . . . . . . . . 171
12.5
LVI Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
12.6
LVI Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
12.7 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
12.7.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
12.7.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
12.2 Introduction
The low-voltage inhibit (LVI) module monitors the voltage on the VDD pin
and will set a low voltage sense bit when VDD voltage falls to the LVI
sense voltage. The LVI will force a reset when the VDD voltage falls to
the LVI trip voltage.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Low-Voltage Inhibit (LVI)
169
Low-Voltage Inhibit (LVI)
12.3 Features
Features of the LVI module include:
•
Two levels of low-voltage condition are detected:
– Low-voltage detection
– Low-voltage reset
•
User-configurable for stop mode
12.4 Functional Description
Figure 12-1 shows the structure of the LVI module. The LVI module
contains a bandgap reference circuit and two comparators. The LVI
monitors VDD voltage during normal MCU operation. When enabled, the
LVI module generates a reset when VDD falls below the VLVR threshold.
In addition to forcing a reset condition, the LVI module has a second
circuit dedicated to low-voltage detection. When VDD falls below VLVS,
the output of the low-voltage comparator asserts the LOWV flag in the
LVI status register (LVISR). In applications that require detecting low
batteries, software can monitor by polling the LOWV bit.
VDD
STOP INSTRUCTION
LVI STOP BIT IN CONFIGURATION REGISTER
LVI PWR BIT IN CONFIGURATION REGISTER
LVIRST BIT IN CONFIGURATION REGISTER
WEAK
BATTERY
DETECTOR
DEAD
BATTERY
DETECTOR
VDD > VLVR = 0
VDD ≤ VLVR = 1
VDD
DIGITAL FILTER
RESET
LVITRIP
CGMXCLK
VDD > VLVS = 0
LOWV
VDD ≤ VLVS = 1
LOWV FLAG
Figure 12-1. LVI Module Block Diagram
Advance Information
170
MC68HC908RF2 — Rev. 1
Low-Voltage Inhibit (LVI)
MOTOROLA
Low-Voltage Inhibit (LVI)
Functional Description
12.4.1 False Trip Protection
The VDD pin level is digitally filtered to reduce false dead battery
detection due to power supply noise. For the LVI module to reset due to
a low-power supply, VDD must remain at or below the VLVR level for a
minimum 32–40 CGMXCLK cycles. See Table 12-1.
Table 12-1. LOWV Bit Indication
VDD
Result
At Level:
For Number of
CGMXCLK Cycles:
VDD > VLVR
ANY
Filter counter remains
clear
VDD < VLVR
< 32 CGMXCLK cycles
No reset, continue
counting CGMXCLK
VDD < VLVR
Between 32 & 40 CGMXCLK
cycles
LVI may generate
a reset after
32 CGMXCLK cycles
VDD < VLVR
> 40 CGMXCLK cycles
LVI is guaranteed to
generate a reset
12.4.2 Short Stop Recovery Option
The LVI has an enable time of tEN. The system stabilization time for
power-on reset and long stop recovery (both 4096 CGMXCLK cycles)
gives a delay longer than the LVI enable time for these startup scenarios.
There is no period where the MCU is not protected from a low-power
condition. However, when using the short stop recovery configuration
option, the 32 CGMXCLK delay must be greater than the LVI turn on
time to avoid a period in startup where the LVI is not protecting the MCU.
NOTE:
The LVI is enabled automatically after reset or stop recovery, if the
LVISTOP of the CONFIG register is set. (See Section 9. Configuration
Register (CONFIG).)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Low-Voltage Inhibit (LVI)
171
Low-Voltage Inhibit (LVI)
12.5 LVI Status Register
The LVI status register flags VDD voltages below the VLVR and VLVS
levels.
Address: $FE0F
Bit 7
Read: LVIOUT
6
5
4
3
2
1
Bit 0
0
LOWV
0
0
0
0
0
0
0
0
0
0
0
0
Write:
Reset:
0
= Unimplemented
Figure 12-2. LVI Status Register (LVISR)
LVIOUT — LVI Output Bit
The read-only flag becomes set when the VDD voltage falls below the
VLVR voltage for 32 to 40 CGMXCLK cycles. Reset clears the LVIOUT
bit.
LOWV— LVI Low Indicator Bit
This read-only flag becomes set when the LVI is detecting VDD
voltage below the VLVS threshold.
12.6 LVI Interrupts
The LVI module does not generate CPU interrupt requests.
12.7 Low-Power Modes
The STOP and WAIT instructions put the MCU in low powerconsumption standby modes.
Advance Information
172
MC68HC908RF2 — Rev. 1
Low-Voltage Inhibit (LVI)
MOTOROLA
Low-Voltage Inhibit (LVI)
Low-Power Modes
12.7.1 Wait Mode
The LVI module remains active in wait mode. The LVI module can
generate a reset if a VDD voltage below the VLVR voltage is detected.
12.7.2 Stop Mode
The LVI can be enabled or disabled in stop mode by setting the
LVISTOP bit in the CONFIG register. (See Section 9. Configuration
Register (CONFIG).)
NOTE:
To minimize STOP IDD, disable the LVI in stop mode.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Low-Voltage Inhibit (LVI)
173
Low-Voltage Inhibit (LVI)
Advance Information
174
MC68HC908RF2 — Rev. 1
Low-Voltage Inhibit (LVI)
MOTOROLA
Advance Information — MC68HC908RF2
Section 13. Input/Output (I/O) Ports
13.1 Contents
13.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
13.3 Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
13.3.1 Port A Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
13.3.2 Data Direction Register A. . . . . . . . . . . . . . . . . . . . . . . . . . 178
13.4 Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
13.4.1 Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
13.4.2 Data Direction Register B . . . . . . . . . . . . . . . . . . . . . . . . . 181
13.2 Introduction
Twelve bidirectional input/output (I/O) pins form two parallel ports in the
32-pin low-profile quad flat pack (LQFP). All I/O pins are programmable
as inputs or outputs. Port A bits PTA6–PTA1 have keyboard wakeup
interrupts and internal pullup resistors.
NOTE:
Connect any unused I/O pins to an appropriate logic level, either VDD or
VSS. Although the I/O ports do not require termination for proper
operation, termination reduces excess current consumption and the
possibility of electrostatic damage.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Input/Output (I/O) Ports
175
Input/Output (I/O) Ports
Addr.
$0000
$0001
Register Name
Read:
Port A Data Register
(PTA) Write:
See page 177.
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
PTB2
PTB1
PTB0
Unaffected by reset
Read:
Port B Data Register
(PTB) Write:
See page 180.
Reset:
Read:
Data Direction Register A
DDRA7
$0004
(DDRA) Write:
See page 178.
Reset:
0
Read:
Data Direction Register B
MCLKEN
$0005
(DDRB) Write:
See page 181.
Reset:
0
PTB3
Unaffected by reset
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 13-1. I/O Port Register Summary
Advance Information
176
MC68HC908RF2 — Rev. 1
Input/Output (I/O) Ports
MOTOROLA
Input/Output (I/O) Ports
Port A
13.3 Port A
Port A is an 8-bit special function port that shares six of its pins with the
keyboard interrupt module (KBD). PTA6–PTA1 contain pullup resistors
enabled when the port pin is enabled as a keyboard interrupt. Port A pins
are also high-current port pins with 3-mA sink capabilities.
13.3.1 Port A Data Register
The port A data register (PTA) contains a data latch for each of the eight
port A pins.
Address:
$0000
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
KBD2
KBD1
Read:
Write:
Reset:
Alternate
Function:
Unaffected by reset
KBD6
KBD5
KBD4
KBD3
= Unimplemented
Figure 13-2. Port A Data Register (PTA)
PTA[7:0] — Port A Data Bits
These read/write bits are software programmable. Data direction of
each port A pin is under the control of the corresponding bit in data
direction register A. Reset has no effect on port A data.
KBD[6:1] — Keyboard Wakeup Pins
The keyboard interrupt enable bits, KBIE[6:1], in the keyboard
interrupt control register enable the port A pin as external interrupt
pins and related internal pullup resistor. See Section 14.
Keyboard/External Interrupt Module (KBI).
NOTE:
The enabling of a keyboard interrupt pin will override the corresponding
definition of the pin in the data direction register. However, the data
direction register bit must be a logic 0 for software to read the pin.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Input/Output (I/O) Ports
177
Input/Output (I/O) Ports
13.3.2 Data Direction Register A
Data direction register A (DDRA) determines whether each port A pin is
an input or an output. Writing a logic 1 to a DDRA bit enables the output
buffer for the corresponding port A pin; a logic 0 disables the output
buffer.
Address:
$0004
Bit 7
6
5
4
3
2
1
Bit 0
DDRA7
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 13-3. Data Direction Register A (DDRA)
DDRA[7:0] — Data Direction Register A Bits
These read/write bits control port A data direction. Reset clears
DDRA[7:0], configuring all port A pins as inputs.
1 = Corresponding port A pin configured as output
0 = Corresponding port A pin configured as input
NOTE:
Avoid glitches on port A pins by writing to the port A data register before
changing data direction register A bits from 0 to 1.
Figure 13-4 shows the port A I/O logic.
When bit DDRAx is a logic 1, reading address $0000 reads the PTAx
data latch. When bit DDRAx is a logic 0, reading address $0000 reads
the voltage level on the pin. The data latch can always be written,
regardless of the state of its data direction bit. Table 13-1 summarizes
the operation of the port A pins.
Advance Information
178
MC68HC908RF2 — Rev. 1
Input/Output (I/O) Ports
MOTOROLA
Input/Output (I/O) Ports
Port A
READ DDRA ($0004)
VDD
INTERNAL DATA BUS
WRITE DDRA ($0004)
KBIEX
INTERNAL
PULLUP
DEVICE
DDRAx
RESET
WRITE PTA ($0000)
PTAx
PTAx
READ PTA ($0000)
Figure 13-4. Port A I/O Circuit
Table 13-1. Port A Pin Functions
KBIE(2)
Bit
DDRA Bit
1
X
X(1)
0
0
0
1
PTA Bit
I/O Pin Mode
Accesses
to DDRA
Accesses to PTA
Read/Write
Read
Write
Input, VDD(4)
DDRA[7:0]
Pin
PTA[7:0](3)
X
Input, Hi-Z(5)
DDRA[7:0]
Pin
PTA[7:0](3)
X
Output
DDRA[7:0]
PTA[7:0]
PTA[7:0]
Notes:
1. X = Don’t care
2. Keyboard interrupt enable bit (see 14.6.2 Keyboard Interrupt Enable Register)
3. Writing affects data register, but does not affect input.
4. I/O pin pulled up to VDD by internal pullup device
5. Hi-Z = High impedance
NOTE:
Setting a keyboard interrupt enable bit (KBIEx) forces the corresponding
keyboard interrupt pin to be an input, overriding the data direction
register. However, the data direction register bit must be a logic 0 for
software to read the pin.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Input/Output (I/O) Ports
179
Input/Output (I/O) Ports
13.4 Port B
Port B is a 4-bit special function port that shares two of its pins with the
timer (TIM) module and one with the buffered internal bus clock MCLK.
13.4.1 Port B Data Register
The port B data register (PTB) contains a data latch for each of the four
port B pins.
Address:
$0001
Bit 7
6
5
4
3
2
1
Bit 0
PTB3
PTB2
PTB1
PTB0
Read:
Write:
Reset:
Unaffected by reset
Alternate
Functions:
TCLK
TCH0
MCLK
= Unimplemented
Figure 13-5. Port B Data Register (PTB)
PTB[3:0] — Port B Data Bits
These read/write bits are software-programmable. Data direction of
each port B pin is under the control of the corresponding bit in data
direction register B. Reset has no effect on port B data.
TCH0 — Timer Channel I/O Bit
The PTB2/TCH0 pin is the TIM channel 0 input capture/output
compare pin. The edge/level select bits, ELS0B:ELS0A, determine
whether the PTB2/TCH0 pin is a timer channel I/O or a generalpurpose I/O pin. See Section 15. Timer Interface Module (TIM).
TCLK — Timer Clock Bit
The PTB3/TCLK pin is the external clock input for TIM. The prescaler
select bits, PS[2:0], select PTB3/TCLK as the TIM clock input. (See
15.9.1 TIM Status and Control Register.) When not selected as the
TIM clock, PTB3/TCLK is available for general-purpose I/O.
Advance Information
180
MC68HC908RF2 — Rev. 1
Input/Output (I/O) Ports
MOTOROLA
Input/Output (I/O) Ports
Port B
MCLK — Bus Clock Bit
The bus clock (MCLK) is driven out of pin PTB0/MCLK when enabled
by the MCLKEN bit in port B data direction register bit 7.
13.4.2 Data Direction Register B
Data direction register B (DDRB) determines whether each port B pin is
an input or an output. Writing a logic 1 to a DDRB bit enables the output
buffer for the corresponding port B pin; a logic 0 disables the output
buffer.
Address:
$0005
Bit 7
Read:
6
5
4
3
2
1
Bit 0
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
0
MCLKEN
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 13-6. Data Direction Register B (DDRB)
MCLKEN — MCLK Enable Bit
This read/write bit enables MCLK to be an output signal on PTB0. If
MCLK is enabled, PTB0 is under the control of MCLKEN. Reset
clears this bit.
1 = MCLK output enabled
0 = MCLK output disabled
DDRB[3:0] — Data Direction Register B Bits
These read/write bits control port B data direction. Reset clears
DDRB[3:0], configuring all port B pins as inputs.
1 = Corresponding port B pin configured as output
0 = Corresponding port B pin configured as input
NOTE:
Avoid glitches on port B pins by writing to the port B data register before
changing data direction register B bits from 0 to 1.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Input/Output (I/O) Ports
181
Input/Output (I/O) Ports
Figure 13-7 shows the port B I/O logic.
READ DDRB ($0005)
INTERNAL DATA BUS
WRITE DDRB ($0005)
DDRBx
RESET
WRITE PTB ($0001)
PTBx
PTBx
READ PTB ($0001)
Figure 13-7. Port B I/O Circuit
When bit DDRBx is a logic 1, reading address $0001 reads the PTBx
data latch. When bit DDRBx is a logic 0, reading address $0001 reads
the voltage level on the pin. The data latch can always be written,
regardless of the state of its data direction bit. Table 13-2 summarizes
the operation of the port B pins.
Table 13-2. Port B Pin Functions
DDRB
Bit
PTB
Bit
I/O Pin
Mode
Accesses
to DDRB
Accesses to PTB
Read/Write
Read
Write
0
X
Input, Hi-Z
DDRB[7]
DDRB[3:0]
Pin
PTB[3:0](1)
1
X
Output
DDRB[7]
DDRB[3:0]
PTB[3:0]
PTB[3:0]
X = Don’t care
Hi-Z = High impedance
1. Writing affects data register, but does not affect input.
Advance Information
182
MC68HC908RF2 — Rev. 1
Input/Output (I/O) Ports
MOTOROLA
Advance Information — MC68HC908RF2
Section 14. Keyboard/External Interrupt Module (KBI)
14.1 Contents
14.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
14.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
14.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
14.4.1 External Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
14.4.2 IRQ1 Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
14.4.3 KBI Module During Break Interrupts. . . . . . . . . . . . . . . . . . 189
14.4.4 Keyboard Interrupt Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
14.4.5 Keyboard Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
14.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
14.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
14.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
14.6 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
14.6.1 IRQ and Keyboard Status and Control Register . . . . . . . . 193
14.6.2 Keyboard Interrupt Enable Register . . . . . . . . . . . . . . . . . . 195
14.2 Introduction
This section describes the maskable external interrupt (IRQ1) input and
six independently maskable keyboard wakeup interrupt pins.
MC68HC908RF2
MOTOROLA
Advance Information
Keyboard/External Interrupt Module (KBI)
183
Keyboard/External Interrupt Module (KBI)
14.3 Features
Features of the KBI include:
•
Dedicated external interrupt pin (IRQ1)
•
Six keyboard interrupt pins with separate keyboard interrupt
enable bits and one keyboard interrupt mask
•
Internal pullup resistor
•
Hysteresis buffer
•
Programmable edge-only or edge- and level-interrupt sensitivity
•
Automatic interrupt acknowledge
14.4 Functional Description
This section provides a functional description of the keyboard/external
interrupt module (KBI).
14.4.1 External Interrupt
A logic 0 applied to the external interrupt pin (IRQ1) can latch a CPU
interrupt request. Figure 14-1 shows the structure of the external (IRQ1)
interrupt of the KBI module.
A logic 0 applied to one or more of the keyboard interrupt pins can latch
a CPU interrupt request. Figure 14-4 shows the structure of the
keyboard interrupts of the KBI module
See Figure 14-2 for a summary of the interrupt and keyboard
input/output (I/O) registers.
Advance Information
184
MC68HC908RF2
Keyboard/External Interrupt Module (KBI)
MOTOROLA
Keyboard/External Interrupt Module (KBI)
Functional Description
ACKI
INTERNAL ADDRESS BUS
RESET
TO CPU FOR
BIL/BIH
INSTRUCTIONS
VECTOR
FETCH
DECODER
VDD
INTERNAL
PULLUP
DEVICE
VDD
IRQ1F
D
CLR
Q
CK
IRQ1
IRQ1
INTERRUPT
REQUEST
SYNCHRONIZER
IRQ1
LATCH
IMASKI
KEYBOARD
INTERRUPT
REQUEST
IRQ1/KEYBOARD
INTERRUPT
REQUEST
MODEI
HIGH
VOLTAGE
DETECT
TO MODE
SELECT
LOGIC
Figure 14-1. IRQ Block Diagram
Addr.
Register Name
Bit 7
6
IRQ and Keyboard Status Read:
and Control Register
$001A
Write:
(INTKBSCR)
See page 193. Reset:
IRQ1F
0
Read:
Keyboard Interrupt Enable
$001B
Register (INTKBIER) Write:
See page 195.
Reset:
0
5
4
IMASKI
MODEI
3
2
KEYF
0
R
ACKK
1
Bit 0
IMASKK
MODEK
0
R
ACKI
0
0
0
0
0
0
0
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
0
0
0
0
0
0
= Unimplemented
R
0
0
0
= Reserved
Figure 14-2. IRQ and Keyboard I/O Register Summary
MC68HC908RF2
MOTOROLA
Advance Information
Keyboard/External Interrupt Module (KBI)
185
Keyboard/External Interrupt Module (KBI)
Interrupt signals on the IRQ1 pin are latched into the IRQ1 latch.
Keyboard interrupts are latched in the keyboard interrupt latch. An
interrupt latch remains set until one of these actions occurs:
•
Vector fetch — A vector fetch automatically generates an interrupt
acknowledge signal that clears IRQ1 latch and keyboard interrupt
latch.
•
Software clear — Software can clear an interrupt latch by writing
to the appropriate acknowledge bit in the interrupt status and
control register (INTKBSCR). Writing a logic 1 to the ACKI bit
clears the IRQ1 latch. Writing a logic 1 to the ACKK bit clears the
keyboard interrupt latch.
•
Reset — A reset automatically clears both interrupt latches.
The IRQ1 pin and keyboard interrupt pins are falling-edge triggered and
are software-configurable to be both falling-edge and low-level triggered.
The MODEI and MODEK bits in the INTKBSCR controls the triggering
sensitivity of the IRQ1 pin and keyboard interrupt pins.
When an interrupt pin is edge-triggered only, the interrupt latch remains
set until a vector fetch, software clear, or reset occurs.
When an interrupt pin is both falling-edge and low-level-triggered, the
interrupt latch remains set until both of these occur:
•
Vector fetch or software clear
•
Return of the interrupt pin to logic 1
The vector fetch or software clear may occur before or after the interrupt
pin returns to logic 1. As long as the pin is low, the interrupt request
remains pending. A reset will clear the latch, the MODEI and MODEK
control bits, thereby clearing the interrupt even if the pin stays low.
When set, the IMASKI and IMASKK bits in the INTKBSCR mask all
external interrupt requests. A latched interrupt request is not presented
to the interrupt priority logic unless the corresponding IMASK<x> bit is
clear.
Advance Information
186
MC68HC908RF2
Keyboard/External Interrupt Module (KBI)
MOTOROLA
Keyboard/External Interrupt Module (KBI)
Functional Description
NOTE:
The interrupt mask (I) in the condition code register (CCR) masks all
interrupt requests, including external interrupt requests.
See Figure 14-3.
FROM RESET
YES
I BIT SET?
NO
INTERRUPT?
YES
NO
STACK CPU REGISTERS
SET I BIT
LOAD PC WITH INTERRUPT VECTOR
FETCH NEXT
INSTRUCTION
SWI
INSTRUCTION?
YES
NO
RTI
INSTRUCTION?
YES
UNSTACK CPU REGISTERS
NO
EXECUTE INSTRUCTION
Figure 14-3. IRQ Interrupt Flowchart
MC68HC908RF2
MOTOROLA
Advance Information
Keyboard/External Interrupt Module (KBI)
187
Keyboard/External Interrupt Module (KBI)
14.4.2 IRQ1 Pin
A logic 0 on the IRQ1 pin can latch an interrupt request into the IRQ1
latch. A vector fetch, software clear, or reset clears the IRQ1 latch. If the
MODEI bit is set, the IRQ1 pin is both falling-edge sensitive and low-level
sensitive. With MODEI set, both of these actions must occur to clear the
IRQ1 latch:
•
Vector fetch or software clear — A vector fetch generates an
interrupt acknowledge signal to clear the latch. Software may
generate the interrupt acknowledge signal by writing a logic 1 to
the ACKI bit in the IRQ and keyboard status and control register
(INTKBSCR). The ACKI bit is useful in applications that poll the
IRQ1 pin and require software to clear the IRQ1 latch. Writing to
the ACKI bit can also prevent spurious interrupts due to noise.
Setting ACKI does not affect subsequent transitions on the IRQ1
pin. A falling edge on IRQ1 that occurs after writing to the ACKI bit
latches another interrupt request. If the IRQ1 mask bit, IMASKI, is
clear, the CPU loads the program counter with the vector address
at locations $FFFA and $FFFB.
•
Return of the IRQ1 pin to logic 1 — As long as the IRQ1 pin is at
logic 0, the IRQ1 latch remains set.
The vector fetch or software clear and the return of the IRQ1 pin to
logic 1 can occur in any order. The interrupt request remains pending as
long as the IRQ1 pin is at logic 0. A reset will clear the latch and the
MODEI control bit, thereby clearing the interrupt even if the pin stays low.
If the MODEI bit is clear, the IRQ1 pin is falling-edge sensitive only. With
MODEI clear, a vector fetch or software clear immediately clears the
IRQ1 latch.The IRQ1F bit in the INTKBSCR register can be used to
check for pending interrupts. The IRQ1F bit is not affected by the IMASKI
bit, which makes it useful in applications where polling is preferred.
Use the BIH or BIL instruction to read the logic level on the IRQ1 pin.
NOTE:
When using the level-sensitive interrupt trigger, avoid false interrupts by
masking interrupt requests in the interrupt routine.
Advance Information
188
MC68HC908RF2
Keyboard/External Interrupt Module (KBI)
MOTOROLA
Keyboard/External Interrupt Module (KBI)
Functional Description
14.4.3 KBI Module During Break Interrupts
The system integration module (SIM) controls whether the IRQ1 or
keyboard interrupt latches can be cleared during the break state. The
BCFE bit in the break flag control register (BFCR) enables software to
clear the latches during the break state. (See 6.8.3 SIM Break Flag
Control Register.)
To allow software to clear the IRQ1 or keyboard latches during a break
interrupt, write a logic 1 to the BCFE bit. If a latch is cleared during the
break state, it remains cleared when the MCU exits the break state.
To protect the latch during the break state, write a logic 0 to the BCFE
bit. With BCFE at logic 0 (its default state), writing to the ACKI or ACKK
bits in the IRQ and keyboard status and control register during the break
state has no effect on the IRQ1 or keyboard latches.
14.4.4 Keyboard Interrupt Pins
Writing to the KBIE6–KBIE1 bits in the keyboard interrupt enable register
independently enables or disables each port A pin as a keyboard
interrupt pin. Enabling a keyboard interrupt pin also enables its internal
pullup device. A logic 0 applied to an enabled keyboard interrupt pin
latches an IRQ1/keyboard interrupt request.
An IRQ1/keyboard interrupt is latched when one or more keyboard pins
goes low after all were high. The MODEK bit in the keyboard status and
control register controls the triggering mode of the keyboard interrupt.
•
If the keyboard interrupt is edge-sensitive only, a falling edge on a
keyboard pin does not latch an interrupt request if another
keyboard pin is already low. To prevent losing an interrupt request
on one pin because another pin is still low, software can disable
the latter pin while it is low.
•
If the keyboard interrupt is falling edge- and low level-sensitive, an
interrupt request is present as long as any keyboard pin is low.
MC68HC908RF2
MOTOROLA
Advance Information
Keyboard/External Interrupt Module (KBI)
189
Keyboard/External Interrupt Module (KBI)
INTERNAL BUS
KBD1
ACKK
VDD
VECTOR FETCH
DECODER
KEYF
RESET
.
TO PULLUP
ENABLE
D
CLR
Q
SYNCHRONIZER
.
CK
KB1IE
KEYBOARD
INTERRUPT
REQUEST
.
KEYBOARD
INTERRUPT LATCH
KBD6
TO PULLUP
ENABLE
IMASKK
MODEK
IRQ1/KEYBOARD
IRQ1
INTERRUPT
INTERRUPT REQUEST
REQUEST
KB6IE
Figure 14-4. Keyboard Interrupt Block Diagram
If the MODEK bit is set, the keyboard interrupt pins are both falling edgeand low level-sensitive, and both of these actions must occur to clear a
keyboard interrupt request:
•
Vector fetch or software clear — A vector fetch generates an
interrupt acknowledge signal to clear the interrupt request.
Software may generate the interrupt acknowledge signal by
writing a logic 1 to the ACKK bit in the keyboard status and control
register (INTKBSCR). The ACKK bit is useful in applications that
poll the keyboard interrupt pins and require software to clear the
keyboard interrupt request. Writing to the ACKK bit prior to leaving
an interrupt service routine also can prevent spurious interrupts
due to noise. Setting ACKK does not affect subsequent transitions
on the keyboard interrupt pins. A falling edge that occurs after
writing to the ACKK bit latches another interrupt request. If the
keyboard interrupt mask bit, IMASKK, is clear, the CPU loads the
program counter with the vector address at locations $FFFA and
$FFFB.
•
Return of all enabled keyboard interrupt pins to logic 1. As long as
any enabled keyboard interrupt pin is at logic 0, the keyboard
interrupt remains set.
Advance Information
190
MC68HC908RF2
Keyboard/External Interrupt Module (KBI)
MOTOROLA
Keyboard/External Interrupt Module (KBI)
Functional Description
The vector fetch or software clear and the return of all enabled keyboard
interrupt pins to logic 1 may occur in any order.
If the MODEK bit is clear, the keyboard interrupt pin is falling edgesensitive only. With MODEK clear, a vector fetch or software clear
immediately clears the keyboard interrupt request.
Reset clears the keyboard interrupt request and the MODEK bit, clearing
the interrupt request even if a keyboard interrupt pin stays at logic 0.
The keyboard flag bit (KEYF) in the IRQ and keyboard status and control
register can be used to see if a pending interrupt exists. The KEYF bit is
not affected by the keyboard interrupt mask bit (IMASKK) which makes
it useful in applications where polling is preferred.
To determine the logic level on a keyboard interrupt pin, use the data
direction register to configure the pin as an input and read the data
register.
NOTE:
Setting a keyboard interrupt enable bit (KBIE<x>) forces the
corresponding keyboard interrupt pin to be an input, overriding the data
direction register. However, the data direction register bit must be a logic
0 for software to read the pin.
14.4.5 Keyboard Initialization
When a keyboard interrupt pin is enabled, it takes time for the internal
pullup to reach a logic 1. Therefore, a false interrupt can occur as soon
as the pin is enabled.
To prevent a false interrupt on keyboard initialization:
1. Mask keyboard interrupts by setting the IMASKK bit in the
keyboard status and control register.
2. Enable the KBI pins by setting the appropriate KBIEx bits in the
keyboard interrupt enable register.
3. Write to the ACKK bit in the keyboard status and control register
to clear any false interrupts.
4. Clear the IMASKK bit.
MC68HC908RF2
MOTOROLA
Advance Information
Keyboard/External Interrupt Module (KBI)
191
Keyboard/External Interrupt Module (KBI)
An interrupt signal on an edge-triggered pin can be acknowledged
immediately after enabling the pin. An interrupt signal on an edge- and
level-triggered interrupt pin must be acknowledged after a delay that
depends on the external load.
Another way to avoid a false interrupt:
1. Configure the keyboard pins as outputs by setting the appropriate
DDRA bits in data direction register A.
2. Write logic 1s to the appropriate port A data register bits.
3. Enable the KBI pins by setting the appropriate KBIEx bits in the
keyboard interrupt enable register.
14.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low powerconsumption standby modes.
14.5.1 Wait Mode
The IRQ1/keyboard interrupts remain active in wait mode. Clearing the
IMASKI or IMASKK bits in the IRQ and keyboard status and control
register enables keyboard interrupt requests to bring the MCU out of wait
mode.
14.5.2 Stop Mode
The IRQ1/keyboard interrupt remains active in stop mode. Clearing the
IMASKI or IMASKK bit in the IRQ and keyboard status and control
register enables keyboard interrupt requests to bring the MCU out of
stop mode.
Advance Information
192
MC68HC908RF2
Keyboard/External Interrupt Module (KBI)
MOTOROLA
Keyboard/External Interrupt Module (KBI)
I/O Registers
14.6 I/O Registers
These registers control and monitor operation of the keyboard/external
interrupt module:
•
IRQ and keyboard status and control register, INTKBSCR
•
Keyboard interrupt enable register, KBIER
14.6.1 IRQ and Keyboard Status and Control Register
The IRQ and keyboard status and control register (INTKBSCR) controls
and monitors operation of the keyboard/external interrupt module. The
INTKBSCR has these functions:
•
Flags the keyboard interrupt requests
•
Acknowledges the keyboard interrupt requests
•
Masks the keyboard interrupt requests
•
Shows the state of the IRQ1 interrupt flag
•
Clears the IRQ1 interrupt latch
•
Masks the IRQ1 interrupt request
•
Controls the triggering sensitivity of the keyboard and IRQ1
interrupt pins
Address: $001A
Bit 7
6
Read:
IRQ1F
0
Write:
R
ACKI
Reset:
0
0
R
5
4
IMASKI
MODEI
0
3
2
KEYF
0
R
ACKK
0
0
0
1
Bit 0
IMASKK
MODEK
0
0
= Reserved
Figure 14-5. IRQ and Keyboard Status and Control Register
(INTKBSCR)
IRQ1F — IRQ1 Flag Bit
This read-only status bit is high when the IRQ1 interrupt is pending.
1 = IRQ1 interrupt pending
0 = IRQ1 interrupt not pending
MC68HC908RF2
MOTOROLA
Advance Information
Keyboard/External Interrupt Module (KBI)
193
Keyboard/External Interrupt Module (KBI)
ACKI — IRQ1 Interrupt Request Acknowledge Bit
Writing a logic 1 to this write-only bit clears the IRQ1 latch. ACKI
always reads as logic 0. Reset clears ACKI.
IMASKI — IRQ1 Interrupt Mask Bit
Writing a logic 1 to this read/write bit disables IRQ1 interrupt requests.
Reset clears IMASKI.
1 = IRQ1 interrupt requests disabled
0 = IRQ1 interrupt requests enabled
MODEI — IRQ1 Triggering Sensitivity Bit
This read/write bit controls the triggering sensitivity of the IRQ1 pin.
Reset clears MODEI.
1 = IRQ1 interrupt requests on falling edges and low levels
0 = interrupt requests on falling edges only
KEYF — Keyboard Flag Bit
This read-only bit is set when a keyboard interrupt is pending. Reset
clears the KEYF bit.
1 = Keyboard interrupt pending
0 = No keyboard interrupt pending
ACKK — Keyboard Acknowledge Bit
Writing a logic 1 to this write-only bit clears the keyboard interrupt
request. ACKK always reads as logic 0. Reset clears ACKK.
IMASKK — Keyboard Interrupt Mask Bit
Writing a logic 1 to this read/write bit prevents the output of the
keyboard interrupt mask from generating interrupt requests. Reset
clears the IMASKK bit.
1 = Keyboard interrupt requests masked
0 = Keyboard interrupt requests not masked
MODEK — Keyboard Triggering Sensitivity Bit
This read/write bit controls the triggering sensitivity of the keyboard
interrupt pins. Reset clears MODEK.
1 = Keyboard interrupt requests on falling edges and low levels
0 = Keyboard interrupt requests on falling edges only
Advance Information
194
MC68HC908RF2
Keyboard/External Interrupt Module (KBI)
MOTOROLA
Keyboard/External Interrupt Module (KBI)
I/O Registers
14.6.2 Keyboard Interrupt Enable Register
The keyboard interrupt enable register (INTKBIER) enables or disables
each port A pin to operate as a keyboard interrupt pin.
Address: $001B
Bit 7
Read:
6
5
4
3
2
1
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
0
0
0
0
0
0
Bit 0
0
0
Write:
Reset:
0
0
= Unimplemented
Figure 14-6. Keyboard Interrupt Enable Register (INTKBIER)
KBIE6–KBIE1 — Keyboard Interrupt Enable Bits
Each of these read/write bits enables the corresponding keyboard
interrupt pin to latch interrupt requests. These bits also enable the
corresponding internal pullup resistor which is enabled only when the
bit is set. Reset clears the keyboard interrupt enable register.
1 = PAx pin enabled as keyboard interrupt pin and corresponding
internal pullup resistor enabled
0 = PAx pin not enabled as keyboard interrupt pin and
corresponding internal pullup resistor disabled
NOTE:
Setting a keyboard interrupt enable bit (KBIEx) forces the corresponding
keyboard interrupt pin to be an input, overriding the data direction
register. However, the data direction register bit must be a logic 0 for
software to read the pin.
MC68HC908RF2
MOTOROLA
Advance Information
Keyboard/External Interrupt Module (KBI)
195
Keyboard/External Interrupt Module (KBI)
Advance Information
196
MC68HC908RF2
Keyboard/External Interrupt Module (KBI)
MOTOROLA
Advance Information — MC68HC908RF2
Section 15. Timer Interface Module (TIM)
15.1 Contents
15.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
15.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
15.4
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
15.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
15.5.1 TIM Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
15.5.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
15.5.3 Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
15.5.4 Unbuffered Output Compare . . . . . . . . . . . . . . . . . . . . . . .202
15.5.5 Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . 203
15.5.6 Pulse-Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . 204
15.5.7 Unbuffered PWM Signal Generation . . . . . . . . . . . . . . . . . 205
15.5.8 Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . 206
15.5.9 PWM Initialization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
15.6 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
15.6.1 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
15.6.2 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208
15.6.3 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
15.7
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 209
15.8 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
15.8.1 TIM Clock Pin (TCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
15.8.2 TIM Channel I/O Pins (TCH0) . . . . . . . . . . . . . . . . . . . . . . 210
15.9 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
15.9.1 TIM Status and Control Register . . . . . . . . . . . . . . . . . . . . 211
15.9.2 TIM Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
15.9.3 TIM Counter Modulo Registers . . . . . . . . . . . . . . . . . . . . . 214
15.9.4 TIM Channel Status and Control Registers . . . . . . . . . . . . 214
15.9.5 TIM Channel Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . .218
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
197
Timer Interface Module (TIM)
15.2 Introduction
This section describes the timer interface module (TIM). The TIM is a
2-channel timer:
•
The first channel, channel 0, provides a timing reference with input
capture, output compare, and pulse-width-modulation (PWM)
functions.
•
The second channel, channel 1, provides reduced functionality as
it doesn’t have an external pin.
Figure 15-1 is a block diagram of the TIM.
15.3 Features
Features of the TIM include:
•
One input capture/output compare channel:
– Rising-edge, falling-edge, or any-edge input capture trigger
– Set, clear, or toggle output compare action
•
Buffered and unbuffered PWM signal generation
•
Programmable TIM clock input:
– 7-frequency internal bus clock prescaler selection
– External TIM clock input (bus frequency ÷ 2 maximum)
•
Free-running or modulo up-count operation
•
Toggle any channel pin on overflow
•
TIM counter stop and reset bits
Advance Information
198
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
Pin Name Conventions
15.4 Pin Name Conventions
The TIM module shares pins with two port B input/output (I/O) port pins.
The full names of the TIM I/O pins and generic pin names are listed in
Table 15-1.
Table 15-1. Pin Name Conventions
TIM Generic
Pin Names
TCH0
TCLK
Full TIM
Pin Names
PTB2/TCH0
PTB3/TCLK
15.5 Functional Description
Figure 15-1 shows the structure of the TIM. The central component of
the TIM is the 16-bit TIM counter that can operate as a free-running
counter or a modulo up-counter. The TIM counter provides the timing
reference for the input capture and output compare functions. The TIM
counter modulo registers, TMODH and TMODL, control the modulo
value of the TIM counter. Software can read the TIM counter value at any
time without affecting the counting sequence.
The TIM channel 0 is programmable independently as input capture or
output compare.
The TIM channel 1 is programmable only as output compare. The output
compare is detected only through an interrupt.
WARNING:
TIM channel 1 should not be configured as an input capture
because this would result in a floating input that would cause a
higher IDD.
Refer to Figure 15-2 for a summary of the TIM I/O registers.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
199
Timer Interface Module (TIM)
PTB3/TCLK
PRESCALER SELECT
INTERNAL
BUS CLOCK
PRESCALER
TSTOP
PS2
TRST
PS1
PS0
16-BIT COUNTER
TOF
TOIE
INTERRUPT
LOGIC
16-BIT COMPARATOR
TMODH:TMODL
TOV0
ELS0B
CHANNEL 0
ELS0A
CH0MAX
PORT
LOGIC
PTB2/TCH0
16-BIT COMPARATOR
TCH0H:TCH0L
CH0F
16-BIT LATCH
MS0A
CH0IE
INTERRUPT
LOGIC
MS0B
INTERNAL BUS
TOV1
ELS1B
CHANNEL 1
ELS1A
CH1MAX
PORT
LOGIC
N/C*
16-BIT COMPARATOR
TCH1H:TCH1L
CH1F
16-BIT LATCH
MS1A
CH1IE
INTERRUPT
LOGIC
*This pin is not available on the MC68HC908RF2.
Figure 15-1. TIM Block Diagram
Addr.
Register Name
Bit 7
Read:
Timer Status and Control
$0020
Register (TSC) Write:
See page 211.
Reset:
TOF
0
0
1
0
Read:
Timer Counter Register
High (TCNTH) Write:
See page 213.
Reset:
Bit 15
14
13
0
0
0
$0021
6
5
TOIE
TSTOP
0
4
3
2
1
Bit 0
0
0
PS2
PS1
PS0
0
0
0
0
12
11
10
9
Bit 8
0
0
0
0
0
TRST
= Unimplemented
Figure 15-2. TIM I/O Register Summary
Advance Information
200
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
Functional Description
Addr.
$0022
$0023
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Timer Counter Register
Low (TCNTL) Write:
See page 213.
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
6
5
4
3
2
1
Bit 0
1
1
1
1
1
1
1
1
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
Read:
Timer Counter Modulo
Register High (TMODH) Write:
See page 214.
Reset:
Timer Counter Read:
Modulo Register Low
Write:
$0024
(TMODL)
See page 214. Reset:
$0025
Read:
Timer Channel 0 Status
and Control Register Write:
(TSC0) See page 215.
Reset:
Read:
Timer Channel 0 Register
$0026
High (TCH0H) Write:
See page 219.
Reset:
Read:
Timer Channel 0 Register
$0027
Low (TCH0L) Write:
See page 219.
Reset:
$0028
Read:
Timer Channel 1 Status
and Control Register Write:
(TSC1) See page 215.
Reset:
Read:
Timer Channel 1 Register
$0029
High (TCH1H)) Write:
See page 219.
Reset:
Read:
Timer Channel 1 Register
$002A
Low (TCH1L)) Write:
See page 219.
Reset:
CH0F
0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
CH1F
0
CH1IE
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
= Unimplemented
Figure 15-2. TIM I/O Register Summary (Continued)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
201
Timer Interface Module (TIM)
15.5.1 TIM Counter Prescaler
The TIM clock source can be one of the seven prescaler outputs or the
TIM clock pin, TCLK. The prescaler generates seven clock rates from
the internal bus clock. The prescaler select bits, PS[2:0], in the TIM
status and control register select the TIM clock source.
15.5.2 Input Capture
With the input capture function, the TIM can capture the time at which an
external event occurs. When an active edge occurs on the pin of an input
capture channel, the TIM latches the contents of the TIM counter into the
TIM channel registers, TCHxH and TCHxL. The polarity of the active
edge is programmable. Input captures can generate TIM CPU interrupt
requests.
NOTE:
TIM channel 1 should not be configured in this mode.
15.5.3 Output Compare
With the output compare function, the TIM can generate a periodic pulse
with a programmable polarity, duration, and frequency. When the
counter reaches the value in the registers of an output compare channel,
the TIM channel 0 can set, clear, or toggle the channel pin. Output
compares can generate TIM CPU interrupt requests for both TIM
channel 0 and TIM channel 1.
NOTE:
TIM channel 1 does not have an external pin associated with it.
15.5.4 Unbuffered Output Compare
Any output compare channel can generate unbuffered output compare
pulses as described in 15.5.3 Output Compare. The pulses are
unbuffered because changing the output compare value requires writing
the new value over the old value currently in the TIM channel registers.
Advance Information
202
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
Functional Description
An unsynchronized write to the TIM channel registers to change an
output compare value could cause incorrect operation for up to two
counter overflow periods. For example, writing a new value before the
counter reaches the old value but after the counter reaches the new
value prevents any compare during that counter overflow period. Also,
using a TIM overflow interrupt routine to write a new, smaller output
compare value may cause the compare to be missed. The TIM may pass
the new value before it is written.
Use these methods to synchronize unbuffered changes in the output
compare value on channel x:
•
When changing to a smaller value, enable channel x output
compare interrupts and write the new value in the output compare
interrupt routine. The output compare interrupt occurs at the end
of the current output compare pulse. The interrupt routine has until
the end of the counter overflow period to write the new value.
•
When changing to a larger output compare value, enable channel
x TIM overflow interrupts and write the new value in the TIM
overflow interrupt routine. The TIM overflow interrupt occurs at the
end of the current counter overflow period. Writing a larger value
in an output compare interrupt routine (at the end of the current
pulse) could cause two output compares to occur in the same
counter overflow period.
15.5.5 Buffered Output Compare
Channels 0 and 1 can be linked to form a buffered output compare
channel whose output appears on the PTB2/TCH0 pin. The TIM channel
registers of the linked pair alternately control the output.
Setting the MS0B bit in TIM channel 0 status and control register (TSC0)
links channel 0 and channel 1. The output compare value in the TIM
channel 0 registers initially controls the output on the TCH0 pin. Writing
to the TIM channel 1 registers enables the TIM channel 1 registers to
synchronously control the output after the TIM overflows. At each
subsequent overflow, the TIM channel registers (0 or 1) that control the
output are the ones written to last. TSC0 controls and monitors the
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
203
Timer Interface Module (TIM)
buffered output compare function, and TIM channel 1 status and control
register (TSC1) is unused.
NOTE:
In buffered output compare operation, do not write new output compare
values to the currently active channel registers. Writing to the active
channel registers is the same as generating unbuffered output
compares.
15.5.6 Pulse-Width Modulation (PWM)
By using the toggle-on-overflow feature with an output compare channel,
the TIM can generate a pulse-width modulation (PWM) signal. The value
in the TIM counter modulo registers determines the period of the PWM
signal. The channel pin toggles when the counter reaches the value in
the TIM counter modulo registers. The time between overflows is the
period of the PWM signal.
As Figure 15-3 shows, the output compare value in the TIM channel
registers determines the pulse width of the PWM signal. The time
between overflow and output compare is the pulse width. Program the
TIM to clear channel 0 pin on output compare if the state of the PWM
pulse is logic 1. Program the TIM to set the pin if the state of the PWM
pulse is logic 0.
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
PULSE
WIDTH
PTB2/TCH0
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
Figure 15-3. PWM Period and Pulse Width
Advance Information
204
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
Functional Description
The value in the TIM counter modulo registers and the selected
prescaler output determines the frequency of the PWM output. The
frequency of an 8-bit PWM signal is variable in 256 increments. Writing
$00FF (255) to the TIM counter modulo registers produces a PWM
period of 256 times the internal bus clock period if the prescaler select
value is $000. See 15.9.1 TIM Status and Control Register.
The value in the TIM channel registers determines the pulse width of the
PWM output. The pulse width of an 8-bit PWM signal is variable in 256
increments. Writing $0080 (128) to the TIM channel registers produces
a duty cycle of 128/256 or 50 percent.
15.5.7 Unbuffered PWM Signal Generation
Any output compare channel can generate unbuffered PWM pulses as
described in 15.5.6 Pulse-Width Modulation (PWM). The pulses are
unbuffered because changing the pulse width requires writing the new
pulse width value over the old value currently in the TIM channel
registers.
An unsynchronized write to the TIM channel registers to change a pulse
width value could cause incorrect operation for up to two PWM periods.
For example, writing a new value before the counter reaches the old
value but after the counter reaches the new value prevents any compare
during that PWM period. Also, using a TIM overflow interrupt routine to
write a new, smaller pulse width value may cause the compare to be
missed. The TIM may pass the new value before it is written.
Use these methods to synchronize unbuffered changes in the PWM
pulse width on channel:
•
When changing to a shorter pulse width, enable channel output
compare interrupts and write the new value in the output compare
interrupt routine. The output compare interrupt occurs at the end
of the current pulse. The interrupt routine has until the end of the
PWM period to write the new value.
•
When changing to a longer pulse width, enable channel TIM
overflow interrupts and write the new value in the TIM overflow
interrupt routine. The TIM overflow interrupt occurs at the end of
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
205
Timer Interface Module (TIM)
the current PWM period. Writing a larger value in an output
compare interrupt routine (at the end of the current pulse) could
cause two output compares to occur in the same PWM period.
NOTE:
In PWM signal generation, do not program the PWM channel to toggle
on output compare. Toggling on output compare prevents reliable
0 percent duty cycle generation and removes the ability of the channel
to self-correct in the event of software error or noise. Toggling on output
compare also can cause incorrect PWM signal generation when
changing the PWM pulse width to a new, much larger value.
15.5.8 Buffered PWM Signal Generation
Channels 0 and 1 can be linked to form a buffered PWM channel whose
output appears on the TCH0 pin. The TIM channel registers of the linked
pair alternately control the pulse width of the output.
Setting the MS0B bit in TIM channel 0 status and control register (TSC0)
links channel 0 and channel 1. The TIM channel 0 registers initially
control the pulse width on the TCH0 pin. Writing to the TIM channel 1
registers enables the TIM channel 1 registers to synchronously control
the pulse width at the beginning of the next PWM period. At each
subsequent overflow, the TIM channel registers (0 or 1) that control the
pulse width are the ones written to last. TSC0 controls and monitors the
buffered PWM function, and TIM channel 1 status and control register
(TSC1) is unused.
NOTE:
In buffered PWM signal generation, do not write new pulse width values
to the currently active channel registers. Writing to the active channel
registers is the same as generating unbuffered PWM signals.
Advance Information
206
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
Functional Description
15.5.9 PWM Initialization
To ensure correct operation when generating unbuffered or buffered
PWM signals, use this initialization procedure:
1. In the TIM status and control register (TSC):
a. Stop the TIM counter by setting the TIM stop bit, TSTOP.
b. Reset the TIM counter by setting the TIM reset bit, TRST.
2. In the TIM counter modulo registers (TMODH and TMODL), write
the value for the required PWM period.
3. In the TIM channel x registers (TCHxH and TCHxL), write the
value for the required pulse width.
4. In TIM channel x status and control register (TSCx):
a. Write 0:1 (for unbuffered output compare or PWM signals) or
1:0 (for buffered output compare or PWM signals) to the
mode select bits, MSxB and MSxA. See Table 15-3.
b. Write 1 to the toggle-on-overflow bit, TOVx.
c. Write 1:0 (to clear output on compare) or 1:1 (to set output on
compare) to the edge/level select bits, ELSxB and ELSxA.
The output action on compare must force the output to the
complement of the pulse width level. See Table 15-3.
NOTE:
In PWM signal generation, do not program the PWM channel to toggle
on output compare. Toggling on output compare prevents reliable
0 percent duty cycle generation and removes the ability of the channel
to self-correct in the event of software error or noise. Toggling on output
compare can also cause incorrect PWM signal generation when
changing the PWM pulse width to a new, much larger value.
5. In the TIM status control register (TSC), clear the TIM stop bit,
TSTOP.
Setting MS0B links channels 0 and 1 and configures them for buffered
PWM operation. The TIM channel 0 registers (TCH0H and TCH0L)
initially control the buffered PWM output. TIM status control register 0
(TSCR0) controls and monitors the PWM signal from the linked
channels.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
207
Timer Interface Module (TIM)
Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIM
overflows. Subsequent output compares try to force the output to a state
it is already in and have no effect. The result is a 0 percent duty cycle
output.
Setting the channel x maximum duty cycle bit (CHxMAX) and clearing
the TOVx bit generates a 100 percent duty cycle output. See 15.9.4 TIM
Channel Status and Control Registers.
15.6 Interrupts
These TIM sources can generate interrupt requests:
•
TIM overflow flag (TOF) — The timer counter value changes on
the falling edge of the internal bus clock. The timer overflow flag
(TOF) bit is set on the falling edge of the internal bus clock
following the timer rollover to $0000. The TIM overflow interrupt
enable bit, TOIE, enables TIM overflow interrupt requests. TOF
and TOIE are in the TIM status and control registers.
•
TIM channel flag (CH0F) — The CH0F bit is set when an input
capture or output compare occurs on channel. Channel TIM CPU
interrupt requests are controlled by the channel interrupt enable
bit, CH1IE.
15.6.1 Low-Power Modes
The WAIT and STOP instructions put the MCU in low powerconsumption standby modes.
15.6.2 Wait Mode
The TIM remains active after the execution of a WAIT instruction. In wait
mode, the TIM registers are not accessible by the CPU. Any enabled
CPU interrupt request from the TIM can bring the MCU out of wait mode.
If TIM functions are not required during wait mode, reduce power
consumption by stopping the TIM before executing the WAIT instruction.
Advance Information
208
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
TIM During Break Interrupts
15.6.3 Stop Mode
The TIM is inactive after the execution of a STOP instruction. The STOP
instruction does not affect register conditions or the state of the TIM
counter. TIM operation resumes when the MCU exits stop mode after an
external interrupt.
15.7 TIM During Break Interrupts
A break interrupt stops the TIM counter.
The system integration module (SIM) controls whether status bits in
other modules can be cleared during the break state. The BCFE bit in
the SIM break flag control register (SBFCR) enables software to clear
status bits during the break state. See 6.8.3 SIM Break Flag Control
Register.
To allow software to clear status bits during a break interrupt, write a
logic 1 to the BCFE bit. If a status bit is cleared during the break state, it
remains cleared when the MCU exits the break state.
To protect status bits during the break state, write a logic 0 to the BCFE
bit. With BCFE at logic 0 (its default state), software can read and write
I/O registers during the break state without affecting status bits. Some
status bits have a 2-step read/write clearing procedure. If software does
the first step on such a bit before the break, the bit cannot change during
the break state as long as BCFE is at logic 0. After the break, doing the
second step clears the status bit.
15.8 I/O Signals
Port B shares two of its pins with the TIM. TCLK can be used as an
external clock input to the TIM prescaler and the TIM channel 0 I/O pin
PTB2/TCH0.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
209
Timer Interface Module (TIM)
15.8.1 TIM Clock Pin (TCLK)
TCLK is an external clock input that can be the clock source for the TIM
counter instead of the prescaled internal bus clock. Select the TCLK
input by writing logic 1s to the three prescaler select bits, PS2–PS0. See
15.9.1 TIM Status and Control Register. The minimum TCLK pulse
width, TCLKLMIN or TCLKHMIN, is:
1
+ tsu
bus frequency
The maximum TCLK frequency is:
bus frequency ÷ 2
Refer to 17.10 Control Timing.
TCLK is available as a general-purpose I/O pin when not used as the
TIM clock input. When the TCLK pin is the TIM clock input, it is an input
regardless of the state of the DDRB3 bit in data direction register B.
15.8.2 TIM Channel I/O Pins (TCH0)
The channel I/O pins are programmable independently as an input
capture pin or an output compare pin. TCH0 can be configured as
buffered output compare or buffered PWM pins.
15.9 I/O Registers
These I/O registers control and monitor operation of the TIM:
•
TIM status and control register, TSC
•
TIM control registers, TCNTH and TCNTL
•
TIM counter modulo registers, TMODH and TMODL
•
TIM channel status and control registers, TSC0 and TSC1
•
TIM channel registers, TCH0H, TCH0L, TCH1H, and TCH1L
Advance Information
210
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
I/O Registers
15.9.1 TIM Status and Control Register
The TIM status and control register (TSC):
•
Enables TIM overflow interrupts
•
Flags TIM overflows
•
Stops the TIM counter
•
Resets the TIM counter
•
Prescales the TIM counter clock
Address:
$0020
Bit 7
Read:
6
5
TOIE
TSTOP
TOF
Write:
0
Reset:
0
4
3
0
0
2
1
Bit 0
PS2
PS1
PS0
0
0
0
TRST
0
1
0
0
= Unimplemented
Figure 15-4. TIM Status and Control Register (TSC)
TOF — TIM Overflow Flag Bit
This read/write flag is set when the TIM counter resets to $0000 after
reaching the modulo value programmed in the TIM counter modulo
registers. Clear TOF by reading the TIM status and control register
when TOF is set and then writing a logic 0 to TOF. If another TIM
overflow occurs before the clearing sequence is complete, then
writing logic 0 to TOF has no effect. Therefore, a TOF interrupt
request cannot be lost due to inadvertent clearing of TOF. Reset
clears the TOF bit. Writing a logic 1 to TOF has no effect.
1 = TIM counter has reached modulo value.
0 = TIM counter has not reached modulo value.
TOIE — TIM Overflow Interrupt Enable Bit
This read/write bit enables TIM overflow interrupts when the TOF bit
becomes set. Reset clears the TOIE bit.
1 = TIM overflow interrupts enabled
0 = TIM overflow interrupts disabled
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
211
Timer Interface Module (TIM)
TSTOP — TIM Stop Bit
This read/write bit stops the TIM counter. Counting resumes when
TSTOP is cleared. Reset sets the TSTOP bit, stopping the TIM
counter until software clears the TSTOP bit.
1 = TIM counter stopped
0 = TIM counter active
NOTE:
Do not set the TSTOP bit before entering wait mode if the TIM is required
to exit wait mode.
TRST — TIM Reset Bit
Setting this write-only bit resets the TIM counter and the TIM
prescaler. Setting TRST has no effect on any other registers.
Counting resumes from $0000. TRST is cleared automatically after
the TIM counter is reset and always reads as logic 0. Reset clears the
TRST bit.
1 = Prescaler and TIM counter cleared
0 = No effect
NOTE:
Setting the TSTOP and TRST bits simultaneously stops the TIM counter
at a value of $0000.
PS2–PS0 — Prescaler Select Bits
These read/write bits select either the TCLK pin or one of the seven
prescaler outputs as the input to the TIM counter as Table 15-2
shows. Reset clears the PS2–PS0 bits.
Table 15-2. Prescaler Selection
PS2–PS0
TIM Clock Source
000
Internal bus clock ÷1
001
Internal bus clock ÷ 2
010
Internal bus clock ÷ 4
011
Internal bus clock ÷ 8
100
Internal bus clock ÷ 16
101
Internal bus clock ÷ 32
110
Internal bus clock ÷ 64
111
TCLK
Advance Information
212
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
I/O Registers
15.9.2 TIM Counter Registers
The two read-only TIM counter registers contain the high and low bytes
of the value in the TIM counter. Reading the high byte (TCNTH) latches
the contents of the low byte (TCNTL) into a buffer. Subsequent reads of
TCNTH do not affect the latched TCNTL value until TCNTL is read.
Reset clears the TIM counter registers. Setting the TIM reset bit (TRST)
also clears the TIM counter registers
NOTE:
If you read TCNTH during a break interrupt, be sure to unlatch TCNTL
by reading TCNTL before exiting the break interrupt. Otherwise, TCNTL
retains the value latched during the break.
Register Name and Address: TCNTH—$0021
Read:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Write:
Reset:
Register Name and Address: TCNTL—$0022
Read:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 15-5. TIM Counter Registers (TCNTH and TCNTL)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
213
Timer Interface Module (TIM)
15.9.3 TIM Counter Modulo Registers
The read/write TIM modulo registers contain the modulo value for the
TIM counter. When the TIM counter reaches the modulo value, the
overflow flag (TOF) becomes set, and the TIM counter resumes counting
from $0000 at the next clock. Writing to the high byte (TMODH) inhibits
the TOF bit and overflow interrupts until the low byte (TMODL) is written.
Reset sets the TIM counter modulo registers.
Register Name and Address: TMODH—$0023
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
1
1
1
1
1
1
1
1
Read:
Write:
Reset:
Register Name and Address: TMODL—$0024
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
1
1
1
1
1
1
1
1
Figure 15-6. TIM Counter Modulo Registers (TMODH and TMODL)
NOTE:
Reset the TIM counter before writing to the TIM counter modulo registers.
15.9.4 TIM Channel Status and Control Registers
Each of the TIM channel status and control registers (TSC0 and TSC1):
•
Flags input captures and output compares
•
Enables input capture and output compare interrupts
•
Selects input capture, output compare, or PWM operation
•
Selects high, low, or toggling output on output compare
•
Selects rising edge, falling edge, or any edge as the active input
capture trigger
•
Selects output toggling on TIM overflow
•
Selects 100 percent PWM duty cycle
•
Selects buffered or unbuffered output compare/PWM operation
Advance Information
214
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
I/O Registers
Register Name and Address: TSC0—$0025
Bit 7
Read:
CH0F
Write:
0
Reset:
0
6
5
4
3
2
1
Bit 0
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
4
3
2
1
Bit 0
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
Register Name and Address: TSC1—$0028
Bit 7
Read:
CH1F
Write:
0
Reset:
0
6
CH1IE
0
5
0
0
= Unimplemented
Figure 15-7. TIM Channel Status and Control Registers
(TSC0 and TSC1)
CHxF — Channel x Flag Bit
When channel x is an input capture channel, this read/write bit is set
when an active edge occurs on the channel x pin. When channel x is
an output compare channel, CHxF is set when the value in the TIM
counter registers matches the value in the TIM channel x registers.
When TIM CPU interrupt requests are enabled (CHxIE = 1), clear
CHxF by reading TIM channel x status and control register with CHxF
set and then writing a logic 0 to CHxF. If another interrupt request
occurs before the clearing sequence is complete, then writing logic 0
to CHxF has no effect. Therefore, an interrupt request cannot be lost
due to inadvertent clearing of CHxF.
Reset clears the CHxF bit. Writing a logic 1 to CHxF has no effect.
1 = Input capture or output compare on channel x
0 = No input capture or output compare on channel x
CHxIE — Channel x Interrupt Enable Bit
This read/write bit enables TIM CPU interrupts on channel x.
Reset clears the CHxIE bit.
1 = Channel x CPU interrupt requests enabled
0 = Channel x CPU interrupt requests disabled
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
215
Timer Interface Module (TIM)
MSxB — Mode Select Bit B
This read/write bit selects buffered output compare/PWM operation.
MSxB exists only in the TIM channel 0 and TIM channel 1 status and
control registers.
Setting MS0B disables the TIM channel 1 status and control register.
Reset clears the MSxB bit.
1 = Buffered output compare/PWM operation enabled
0 = Buffered output compare/PWM operation disabled
MSxA — Mode Select Bit A
When ELSxB:A ≠ 00, this read/write bit selects either input capture
operation or unbuffered output compare/PWM operation.
See Table 15-3.
1 = Unbuffered output compare/PWM operation
0 = Input capture operation
When ELSxB:A = 00, this read/write bit selects the initial output level
of the TCH0 pin. See Table 15-3. Reset clears the MSxA bit.
1 = Initial output level low
0 = Initial output level high
NOTE:
Before changing a channel function by writing to the MSxB or MSxA bit,
set the TSTOP and TRST bits in the TIM status and control register
(TSC).
ELSxB and ELSxA — Edge/Level Select Bits
When channel 0 is an input capture channel, these read/write bits
control the active edge-sensing logic on channel x.
When channel x is an output compare channel, ELSxB and ELSxA
control the channel x output behavior when an output compare
occurs.
When ELSxB and ELSxA are both clear, channel x is not connected
to port B, and pin PTB0/TCH0 is available as a general-purpose I/O
pin. Table 15-3 shows how ELSxB and ELSxA work. Reset clears the
ELSxB and ELSxA bits.
NOTE:
TIM channel 1 does not have an external pin associated with it.
Advance Information
216
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
I/O Registers
Table 15-3. Mode, Edge, and Level Selection
MSxB:MSxA
ELSxB:ELSxA
X0
00
Mode
Output preset
NOTE:
Configuration
Pin under port control;
initial output level high
X1
00
Pin under port control;
initial output level low
00
01
Capture on rising edge only
00
10
00
11
01
01
01
10
01
11
1X
01
1X
10
1X
11
Input capture
Capture on falling edge only
Capture on rising or
falling edge
Output
compare or
PWM
Buffered output
compare or
buffered PWM
Toggle output on compare
Clear output on compare
Set output on compare
Toggle output on compare
Clear output on compare
Set output on compare
Before enabling a TIM channel register for input capture operation, make
sure that the PTB/TCH0 pin is stable for at least two bus clocks.
TOVx — Toggle On Overflow Bit
When channel 0 is an output compare channel, this read/write bit
controls the behavior of the channel 0 output when the TIM counter
overflows. When channel 0 is an input capture channel, TOV0 has no
effect. Reset clears the TOV0 bit.
1 = Channel x pin toggles on TIM counter overflow.
0 = Channel x pin does not toggle on TIM counter overflow.
NOTE:
The state of TOV1 has no effect since there is no pin.
When TOVx is set, a TIM counter overflow takes precedence over a
channel x output compare if both occur at the same time.
Channel 1 should not be configured in input capture mode.
WARNING:
The user must configure TIM channel 1 in a mode other than input
capture. It is recommended that this procedure be part of the
initialization of the system after reset.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
217
Timer Interface Module (TIM)
&+[0$;²&KDQQHO[0D[LPXP'XW\&\FOH%LW
When the TOVx bit is at logic 1 and clear output on compare is
selected, setting the CHxMAX bit forces the duty cycle of buffered and
unbuffered PWM signals to 100 percent. As Figure 15-8 shows, the
CHxMAX bit takes effect in the cycle after it is set or cleared. The
output stays at 100 percent duty cycle level until the cycle after
CHxMAX is cleared.
NOTE:
The PWM 0 percent duty cycle is defined as output low all of the time.
To generate the 0 percent duty cycle, select clear output on compare
and then clear the TOVx bit (CHxMAX = 0). The PWM 100 percent duty
cycle is defined as output high all of the time. To generate the 100
percent duty cycle, use the CHxMAX bit in the TSCx register.
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
PTBx/TCHx
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
CHxMAX
Figure 15-8. CHxMAX Latency
15.9.5 TIM Channel Registers
These read/write registers contain the captured TIM counter value of the
input capture function or the output compare value of the output
compare function. The state of the TIM channel registers after reset is
unknown.
In input capture mode (MSxB:MSxA = 0:0), reading the high byte of the
TIM channel x registers (TCHxH) inhibits input captures until the low
byte (TCHxL) is read.
Advance Information
218
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Timer Interface Module (TIM)
I/O Registers
In output compare mode (MSxB:MSxA ≠ 0:0), writing to the high byte of
the TIM channel x registers (TCHxH) inhibits output compares until the
low byte (TCHxL) is written.
Register Name and Address: TCH0H—$0026
Read:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Write:
Reset:
Indeterminate after reset
Register Name and Address: TCH0L—$0027
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
Indeterminate after reset
Figure 15-9. TIM Channel 0 Registers (TCH0H and TCH0L)
Register Name and Address: TCH1H—$0029
Read:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Write:
Reset:
Indeterminate after reset
Register Name and Address: TCH1L—$002A
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
Indeterminate after reset
Figure 15-10. TIM Channel 1 Registers (TCH1H and TCH1L)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Timer Interface Module (TIM)
219
Timer Interface Module (TIM)
Advance Information
220
MC68HC908RF2 — Rev. 1
Timer Interface Module (TIM)
MOTOROLA
Advance Information — MC68HC908RF2
Section 16. PLL Tuned UHF Transmitter Module
16.1 Contents
16.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
16.3
Transmitter Functional Description . . . . . . . . . . . . . . . . . . . . . 223
16.4
Phase-Lock Loop (PLL) and Local Oscillator . . . . . . . . . . . . . 223
16.5
RF Output Stage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
16.6
Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
16.7
Microcontroller Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
16.8
State Machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
16.9
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .228
16.10 Data Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
16.11 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
16.11.1 Application Schematics in OOK
and FSK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
16.11.2 Complete Application Schematic . . . . . . . . . . . . . . . . . . . . 232
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
PLL Tuned UHF Transmitter Module
221
PLL Tuned UHF Transmitter Module
16.2 Introduction
This section describes the integrated radio frequency (RF) module. This
module integrates an ultra high frequency (UHF) transmitter offering
these key features:
•
Switchable frequency bands: 315, 434, and 868 MHz
•
On/off keying (OOK) and frequency shift keying (FSK) modulation
•
Adjustable output power range
•
Fully integrated voltage-controlled oscillator (VCO)
•
Supply voltage range: 1.9 to 3.7 V
•
Very low standby current: 0.5 nA @ TA = 25°C
•
Low supply voltage shutdown
•
Data clock output for microcontroller
•
Low external component count
Architecture of the module is described in Figure 16-1.
BAND
REXT
VCO
VCC
MODE
DATA
PFD
FIRST
ORDER
GND
CONTROL
ENABLE
÷32
÷2
ENABLE
ENABLE_FSK
DATA_OOK
DATA_FSK
XTAL0
RFOUT
GNDRF
XCO
CFSK
PA
÷64
DRIVER
DATACLK
XTAL1
Figure 16-1. Simplified Integrated RF Module Block Diagram
Advance Information
222
MC68HC908RF2 — Rev. 1
PLL Tuned UHF Transmitter Module
MOTOROLA
PLL Tuned UHF Transmitter Module
Transmitter Functional Description
16.3 Transmitter Functional Description
The transmitter is a phase-locked loop (PLL) tuned low-power UHF
transmitter. The different modes of operation are controlled by the
microcontroller through several digital input pins. The power supply
voltage ranges from 1.9 V to 3.7 V allowing operation with a single
lithium cell.
16.4 Phase-Lock Loop (PLL) and Local Oscillator
The VCO is a completely integrated relaxation oscillator. The phase
frequency detector (PFD) and the loop filter are fully integrated.The
exact output frequency is equal to:
fRFOUT = fXTAL x PLL divider ratio
The frequency band of operation is selected through the BAND pin.
Table Table 16-1 provides details for each frequency band selection.
Table 16-1. Frequency Band Selection
and Associated Divider Ratios
BAND Input
Level
Frequency
Band (MHz)
PLL Divider
Ratio
315
High
Crystal Oscillator
Frequency (MHz)
9.84
32
434
13.56
Low
868
64
An out-of-lock function is performed by monitoring the internal PFD
output voltage. When it exceeds its limits, the RF output stage is
disabled.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
PLL Tuned UHF Transmitter Module
223
PLL Tuned UHF Transmitter Module
16.5 RF Output Stage
The output stage is a single-ended square wave switched current
source. Harmonics will be present in the output current drive. Their
radiated absolute level depends on the antenna characteristics and
output power. Typical application demonstrates compliance to European
Telecommunications Standards Institute (ETSI) standard.
A resistor REXT connected to the REXT pin controls the output power
allowing a tradeoff between radiated power and current consumption.
The output voltage is internally clamped to VCC ± 2 VBE (typically
VCC ±1.5 V @ TA = 25°C).
16.6 Modulation
If a low-logic level is applied on pin MODE, then the on/off keying (OOK)
modulation is selected. This modulation is performed by switching on/off
the RF output stage. The logic level applied on pin DATA controls the
output stage state:
DATA = 0 → output stage off
DATA = 1 → output stage on
If a high-logic level is applied on pin MODE, then frequency shift keying
(FSK) modulation is selected. This modulation is achieved by
modulating the frequency of the reference oscillator. This frequency
change is performed by switching the external crystal load capacitor.
The logic level applied on pin DATA controls the internal switch
connected to pin CFSK:
DATA = 0 → switch off
DATA = 1 → switch on
In case of Figure 16-5, where the two capacitors C6 and C9 are in
series:
DATA = 0 leads to the high value of the carrier frequency
DATA = 1 leads to the low value of the carrier frequency
Advance Information
224
MC68HC908RF2 — Rev. 1
PLL Tuned UHF Transmitter Module
MOTOROLA
PLL Tuned UHF Transmitter Module
Microcontroller Interfaces
This crystal pulling solution implies that the RF output frequency
deviation equals the crystal frequency deviation multipled by the PLL
divider ratio (see Table 16-1).
16.7 Microcontroller Interfaces
Four digital input pins (ENABLE, DATA, BAND, and MODE) enable the
circuit to be controlled by a microcontroller. It is recommended to
configure the band frequency and the modulation type before enabling
the circuit. In a typical application the input pins BAND and MODE are
hardwired.
One digital output (DATACLK) provides the microcontroller a reference
frequency for data clocking. This frequency is equal to the crystal
oscillator frequency divided by 64 (see Table 16-2).
Table 16-2. DATACLK Frequency
versus Crystal Oscillator Frequency
Crystal Oscillator Frequency
(MHz)
DATACLK Frequency
(kHz)
9.84
154
13.56
212
16.8 State Machine
Figure 16-2 details the main state machine.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
PLL Tuned UHF Transmitter Module
225
PLL Tuned UHF Transmitter Module
POWER ON
AND ENABLE = 0
STATE 1
STANDBY MODE
ENABLE = 0
ENABLE = 1
STATE 2
PLL ENABLED
BUT OUT OF LOCK-IN RANGE
PLL IN
LOCK-IN RANGE
PLL OUT OF
LOCK-IN RANGE
ENABLE = 0
STATE 6
SHUTDOWN MODE
VBattery < VShutdoown
STATE 3
PLL ACQUISITION,
READY TO TRANSMIT
DATA
STATE 4
TRANSMISSION MODE
PLL IN
LOCK-IN RANGE
PLL OUT OF
LOCK-IN RANGE
STATE 5
PLL OUT OF LOCK-IN RANGE
Figure 16-2. Main State Machine
Advance Information
226
MC68HC908RF2 — Rev. 1
PLL Tuned UHF Transmitter Module
MOTOROLA
PLL Tuned UHF Transmitter Module
State Machine
State 1
The circuit is in standby mode and draws only a leakage current from
the power supply.
State 2
In this state, tKHPLL is enabled but out of the lock-in range. Therefore
the RF output stage is switched off preventing any data transmission.
DDWDFORFNLVDYDLODEOHRQSLQ'$7$&/.In normal operation, this
state is transitional.
State 3
In this state, the PLL is within the lock-in range.
If t < tPLL_Lock_In, then the PLL can still be in acquisition mode.
If t ≥ tPLL_Lock_In, then the PLL is locked.
The circuit is ready to transmit in band and is waiting for the first data
(see Figure 16-3).
State 4
A rising edge on pin DATA starts the transmission. Data entered on
pin DATA are output on pin RFOUT. The modulation is the one
selected through the level applied on pin MODE.
State 5
An out-of-lock condition has been detected. The RF output stage is
switched off preventing any data transmission. DDWDFORFNLVDYDLODEOH
RQSLQ'$7$&/.
State 6
When the supply voltage falls below the shutdown voltage threshold
(VSDWN) the whole circuit is switched off. Applying a low level on pin
ENABLE is the only condition to get out of this state.
Figure 16-3 shows the waveforms of the main signals for a typical
application cycle
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
PLL Tuned UHF Transmitter Module
227
PLL Tuned UHF Transmitter Module
ENABLE
DATACLK
tDATACLK_Settling
tPLL_Lock_In
SEE NOTE
DATA
MODE = 0,
OOK MODULATION
fCarrier
RFOUT
MODE = 1,
FSK MODULATION
fCarrier1
STATE 1
STATE 2
fCarrier
fCarrier2
STATE 3
fCarrier1
fCarrier2
STATE 4
STATE 1
Note: PLL locked, circuit ready to tramsmit in band.
Figure 16-3. Signals, Waveforms, and Timing Definitions
16.9 Power Management
When the battery voltage falls below the shutdown voltage threshold
(VSDWN) the whole circuit is switched off.
NOTE:
After this shutdown, the circuit is latched until a low level is applied on
pin ENABLE (see state 6 under 16.8 State Machine).
16.10 Data Clock
When the data clock starts, the high-to-low ratio may be uneven.
Similarly the clock is switched off asynchronously so the last period
length is not guaranteed.
Advance Information
228
MC68HC908RF2 — Rev. 1
PLL Tuned UHF Transmitter Module
MOTOROLA
PLL Tuned UHF Transmitter Module
Application Information
16.11 Application Information
This subsection provides application information for the usage of the
UHF transmitter module.
16.11.1 Application Schematics in OOK and FSK Modulation
Figure 16-4 and Figure 16-5 show application schematics in OOK and
FSK modulation for the 315-MHz and 434-MHz frequency bands. For
868-MHz band application, the input pin BAND must be wired to GND.
See component description in Table 16-4 and Table 16-5.
VCC
VCC
TO MCU
DATACLK
DATA
ENABLE
BAND
VCC
GND
GNDRF
XTAL1
RFOUT
XTAL0
VCC
Y1
REXT
C6
R2
MODE
CFSK
MATCHING
NETWORK
ANTENNA
NC
C7
C8
NC = NO CONNECTION
Figure 16-4. Application Schematic in OOK Modulation,
315-MHz and 434-MHz Frequency Bands
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
PLL Tuned UHF Transmitter Module
229
PLL Tuned UHF Transmitter Module
VCC
VCC
TO MCU
C6
DATACLK
MODE
DATA
ENABLE
BAND
VCC
GND
GNDRF
XTAL1
RFOUT
XTAL0
VCC
Y1
REXT
MATCHING
NETWORK
CFSK
C7
R2
C9
ANTENNA
C8
Figure 16-5. Application Schematic in FSK Modulation,
315-MHz and 434-MHz Frequency Bands
Table 16-3. Component Description
Component
Y1
Function
Crystal
R2
RF output level setting resistor (R EXT)
C6
Crystal load capacitor
C7
Value
Unit
315-MHz band: 9.84, see Table 16-5
MHz
434-MHz band: 13.56, see Table 16-5
MHz
868-MHz band: 13.56, see Table 16-5
MHz
12
kΩ
OOK modulation: 18
pF
FSK modulation: 22
pF
10
nF
100
pF
see Table 16-5
pF
Power supply decoupling capacitor
C8
C9
Crystal pulling capacitor for FSK modulation only
Advance Information
230
MC68HC908RF2 — Rev. 1
PLL Tuned UHF Transmitter Module
MOTOROLA
PLL Tuned UHF Transmitter Module
Application Information
A example of crystal reference is: Tokyo Denpa TTS-3B 13568.750 kHz,
see Table 16-4.
Table 16-4. Recommended Crystal Characteristics
(SMD Ceramic Package)
Parameter
Value
Unit
Load capacitance
20
pF
Motional capacitance
6.7
fF
Static capacitance
2
pF
Loss resistance
40
W
Table 16-5. Crystal Pulling Capacitor Value
versus Carrier Frequency Total Deviation
Carrier Frequency
(MHz)
434
868
Carrier Frequency
Total Deviation
(kHz)
Capacitor Value
(pF)
40
18
70
10
100
6.8
80
18
140
10
200
6.8
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
PLL Tuned UHF Transmitter Module
231
PLL Tuned UHF Transmitter Module
16.11.2 Complete Application Schematic
Figure 16-6 gives a complete application schematic using the Motorola
MC68HC908RF2. 22.PRGXODWLRQLVVHOHFWHGI&DUULHU 0+]
IRQ1
RST
PTA7
PTA6/KBD6
PTA5/KBD5
PTA4/KBD4
SW2
PTA3/KBD3
PTA2/KBD2
SW1
25
26
27
28
29
30
32
31
VBATT
PTA1/KBD1
1
24
2
23
PTA0
20
6
19
7
18
8
17
PTB3/TCLK
DATACLK
DATA
DATA
BAND
VBATT
16
XTAL0
MC68HC908RF2
5
9
Y1
C3
10 nF
OSC1
15
XTAL1
21
14
GND
C10 18 pF
4
13
PTB2/TCH0
DATA
22
12
ENABLE
3
11
PTB1
VSS
OSC2
10
PTB0/MCLK
VDD
MODE
ENABLE
VCC
GNDDRF
RFOUT
VCC
CFSK
REXT
13.56 MHz
R2 12 K
ENABLE
VBATT
C9
2.2 pF
C6
10 nF
C5
100 pF
Figure 16-6. Complete Application Schematic in OOK Modulation,
434-MHz Frequency Band
Advance Information
232
MC68HC908RF2 — Rev. 1
PLL Tuned UHF Transmitter Module
MOTOROLA
Advance Information — MC68HC908RF2
Section 17. Preliminary Electrical Specifications
17.1 Contents
17.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
17.3
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 234
17.4
Functional Operating Range. . . . . . . . . . . . . . . . . . . . . . . . . . 235
17.5
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
17.6
1.8-Volt to 3.3-Volt DC Electrical Characteristics
Excluding UHF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
17.7
3.0-Volt DC Electrical Characteristics
Excluding UHF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
17.8
2.0-Volt DC Electrical Characteristics
Excluding UHF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
17.9 UHF Transmitter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
17.9.1 UHF Module Electrical Characteristics. . . . . . . . . . . . . . . . 239
17.9.2 UHF Module Output Power Measurement . . . . . . . . . . . . . 244
17.10 Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
17.11 Internal Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . 246
17.12 LVI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
17.13 Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
17.2 Introduction
This section contains preliminary electrical and timing specifications.
NOTE:
The timing specifications, electrical, and thermal characteristic values
outlined in this section are design targets and have not yet been fully
tested.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Preliminary Electrical Specifications
233
Preliminary Electrical Specifications
17.3 Absolute Maximum Ratings
Maximum ratings are the extreme limits to which the MCU can be
exposed without permanently damaging it.
NOTE:
This device is not guaranteed to operate properly at the maximum
ratings. Refer to 17.6 1.8-Volt to 3.3-Volt DC Electrical
Characteristics Excluding UHF Module, 17.7 3.0-Volt DC Electrical
Characteristics Excluding UHF Module, 17.8 2.0-Volt DC Electrical
Characteristics Excluding UHF Module, and 17.9.1 UHF Module
Electrical Characteristics for guaranteed operating conditions.
Characteristic(1)
Symbol
Value
Unit
Supply voltage
VDD
–0.3 to +3.6
V
Input voltage
VIn
VSS –0.3 to VDD +0.3
V
ESD HBM voltage capability on each pin(2)
—
± 2000
V
ESD MM voltage capability on each pin(3)
—
± 150
V
I
± 15
mA
IPTA7–IPTA0
± 25
mA
Maximum current out of VSS
IMVSS
100
mA
Maximum current into VDD
IMVDD
100
mA
Storage temperature
TSTG
–55 to +150
°C
Maximum current per pin
Excluding VDD, VSS, PTA7–PTA0,
and UHF module pins
Maximum current for pins
PTA7–PTA0
1. Voltages referenced to VSS.
2. Human Body Model, AEC-Q100-002 Rev. C
3. Machine Model, AEC-Q100-003 Rev. D
NOTE:
This device contains circuitry to protect the inputs against damage due
to high static voltages or electric fields; however, it is advised that normal
precautions be taken to avoid application of any voltage higher than
maximum-rated voltages to this high-impedance circuit. For proper
operation, it is recommended that VIn and VOut be constrained to the
range VSS ≤ (VIn or VOut) ≤ VDD. Reliability of operation is enhanced if
unused inputs are connected to an appropriate logic voltage level (for
example, either VSS or VDD).
Advance Information
234
MC68HC908RF2 — Rev. 1
Preliminary Electrical Specifications
MOTOROLA
Preliminary Electrical Specifications
Functional Operating Range
17.4 Functional Operating Range
Characteristic
Operating temperature range(1)
Operating voltage range
Symbol
Min
Max
Unit
TA
–40
85
°C
VDD
1.8
3.6
V
1. Extended temperature range to be determined
17.5 Thermal Characteristics
Characteristic
Symbol
Value
Unit
Thermal resistance
LQFP (32 pin)
θJA
TBD
°C/W
I/O pin power dissipation
PI/O
User determined
W
Power dissipation(1)
PD
PD = (IDD x VDD) + PI/O =
K/(TJ + 273°C)
W
Constant(2)
K
Average junction temperature
Maximum junction temperature
PD x (TA + 273°C)
+ PD2 x θJA
W/°C
TJ
TA + (PD x θJA)
°C
TJM
100
°C
1. Power dissipation is a function of temperature.
2. K is a constant unique to the device. K can be determined for a known TA and measured
PD. With this value of K, P D and TJ can be determined for any value of TA.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Preliminary Electrical Specifications
235
Preliminary Electrical Specifications
17.6 1.8-Volt to 3.3-Volt DC Electrical Characteristics Excluding UHF Module
Characteristic(1)
Symbol
Min
Typ(2)
Max
Unit
Output high voltage
(ILoad = –1.2 mA)
(ILoad = –2.0 mA)
VOH
VDD –0.3
VDD –1.0
—
—
—
—
V
Output low voltage
(ILoad = 1.2 mA)
(ILoad = 3.0 mA)
(ILoad = 3.0 mA) PTA7–PTA0 only
VOL
—
—
—
—
—
—
0.3
1.0
0.3
Input high voltage, all ports, IRQ1, OSC1
VIH
0.7 x VDD
—
VDD + 0.3
V
Input low voltage, all ports, IRQ1, OSC1
VIL
VSS
—
0.3 x VDD
V
—
—
—
—
4.3
1.2
mA
mA
—
—
—
—
10
—
50
—
—
100
—
350
nA
nA
µA
µA
V
VDD supply current
Run(3) (fop= 2.0 MHz)
Wait
(4)
(fop= 2.0 MHz)
Stop(5)
IDD
25°C
–40°C to 85°C
25°C with LVI enabled
–40°C to 85°C with LVI enabled
I/O ports high-impedance leakage current(6)
IIL
—
—
±1
µA
Input current
IIn
—
—
±1
µA
Capacitance
Ports (as input or output)
COut
CIn
—
—
—
—
12
8
pF
POR re-arm voltage(7)
VPOR
0
—
200
mV
POR reset voltage(8)
VPOR
0
700
800
mV
POR rise time ramp rate(9)
RPOR
0.02
—
—
V/ms
Monitor mode entry voltage
VHI
VDD + 2.5
—
8
V
Pullup resistor, PTA6–PTA1, IRQ1
RPU
50
80
120
kΩ
1. Parameters are design targets at VDD = 1.8 V to 3.3 V, VSS = 0 Vdc, TA = –40oC to +85oC, unless otherwise noted
2. Typical values reflect average measurements at midpoint of voltage range, 25°C only.
3. Run (operating) IDD measured using internal clock generator module (fop= 2.0 MHz). VDD = 3.3 Vdc. All inputs 0.2 V from
rail. No dc loads. Less than 100 pF on all outputs. All ports configured as inputs. CL = 20 pF. OSC2 capacitance linearly
affects run IDD. Measured with all modules enabled.
4. Wait IDD measured using internal clock generator module, fop = 2.0 MHz. All inputs 0.2 V from rail; no dc loads; less than
100 pF on all outputs. C L = 20 pF. OSC2 capacitance linearly affects wait IDD. All ports configured as inputs.
5. Stop IDD measured with no port pins sourcing current, all modules disabled except as noted.
6. Pullups and pulldowns are disabled.
7. Maximum is highest voltage that POR is guaranteed.
8. Maximum is highest voltage that POR is possible.
9. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum
VDD is reached.
Advance Information
236
MC68HC908RF2 — Rev. 1
Preliminary Electrical Specifications
MOTOROLA
Preliminary Electrical Specifications
3.0-Volt DC Electrical Characteristics Excluding UHF Module
17.7 3.0-Volt DC Electrical Characteristics Excluding UHF Module
Characteristic(1)
Symbol
Min
Typ(2)
Max
Unit
Output high voltage
(ILoad = –2.0 mA)
(ILoad = –8.0 mA)
VOH
VDD –0.3
VDD –1.0
—
—
—
—
V
Output low voltage
(ILoad = 2.0 mA)
(ILoad = 6.5 mA)
(ILoad = 5.0 mA) PTA7–PTA0 only
VOL
—
—
—
—
—
—
0.3
1.0
0.3
Input high voltage, all ports, IRQ1, OSC1
VIH
0.7 x VDD
—
VDD + 0.3
V
Input low voltage, all ports, IRQ1, OSC1
VIL
VSS
—
0.3 x VDD
V
—
—
—
—
8.6
1.2
mA
mA
—
—
—
—
10
—
50
—
—
100
—
350
nA
nA
µA
µA
V
VDD supply current
Run(3) (fop= 4.0 MHz)
Wait
(4)
(fop= 4.0 MHz)
Stop(5)
IDD
25°C
–40°C to 85°C
25°C with LVI enabled
–40°C to 85°C with LVI enabled
I/O ports high-impedance leakage current(6)
IIL
—
—
±1
µA
Input current
IIn
—
—
±1
µA
Capacitance
Ports (as input or output)
COut
CIn
—
—
—
—
12
8
pF
POR re-arm voltage(7)
VPOR
0
—
200
mV
POR reset voltage(8)
VPOR
0
700
800
mV
POR rise time ramp rate(9)
RPOR
0.02
—
—
V/ms
Monitor mode entry voltage
VHI
VDD+ 2.5
—
8
V
Pullup resistor, PTA6–PTA1, IRQ1
RPU
50
80
120
kΩ
1. Parameters are design targets at VDD = 3.0 ± 10%, VSS = 0 Vdc, TA = –40oC to +85oC, unless otherwise noted
2. Typical values reflect average measurements at midpoint of voltage range, 25°C only.
3. Run (operating) IDD measured using internal clock generator module (fop= 4.0 MHz). VDD = 3.3 Vdc. All inputs 0.2 V from
rail. No dc loads. Less than 100 pF on all outputs. All ports configured as inputs. CL = 20 pF. OSC2 capacitance linearly
affects run IDD. Measured with all modules enabled.
4. Wait IDD measured using internal clock generator module, fop = 4.0 MHz. All inputs 0.2 V from rail; no dc loads; less than
100 pF on all outputs. C L = 20 pF. OSC2 capacitance linearly affects wait IDD. All ports configured as inputs.
5. Stop IDD measured with no port pins sourcing current, all modules disabled except as noted.
6. Pullups and pulldowns are disabled.
7. Maximum is highest voltage that POR is guaranteed.
8. Maximum is highest voltage that POR is possible.
9. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum
VDD is reached.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Preliminary Electrical Specifications
237
Preliminary Electrical Specifications
17.8 2.0-Volt DC Electrical Characteristics Excluding UHF Module
Characteristic(1)
Symbol
Min
Typ(2)
Max
Unit
Output high voltage
(ILoad = –1.2 mA)
(ILoad = –2.0 mA)
VOH
VDD –0.3
VDD –1.0
—
—
—
—
V
Output low voltage
(ILoad = 1.2 mA)
(ILoad = 3.0 mA)
(ILoad = 3.0 mA) PTA7–PTA0 only
VOL
—
—
—
—
—
—
0.3
1.0
0.3
Input high voltage, all ports, IRQ1, OSC1
VIH
0.7 x VDD
—
VDD + 0.3
V
Input low voltage, all ports, IRQ1, OSC1
VIL
VSS
—
0.3 x VDD
V
—
—
—
—
2.5
850
mA
µA
—
—
—
—
10
—
50
—
—
100
—
350
nA
nA
µA
µA
V
VDD supply current
Run(3) (fop= 2.0 MHz)
Wait
(4)
(fop= 2.0 MHz)
Stop(5)
IDD
25°C
–40 °C to 85°C
25°C with LVI enabled
–40°C to 85°C with LVI enabled
I/O ports high-impedance leakage current(6)
IIL
—
—
±1
µA
Input current
IIn
—
—
±1
µA
Capacitance
Ports (as input or output)
COut
CIn
—
—
—
—
12
8
pF
POR re-arm voltage(7)
VPOR
0
—
200
mV
POR reset voltage(8)
VPOR
0
700
800
mV
POR rise time ramp rate(9)
RPOR
0.02
—
—
V/ms
Monitor mode entry voltage
VHI
VDD+ 2.5
—
8
V
Pullup resistor, PTA6–PTA1, IRQ1
RPU
50
80
120
kΩ
1. Parameters are design targets at VDD = 2.0 ± 10%, VSS = 0 Vdc, TA = –40oC to +85oC, unless otherwise noted
2. Typical values reflect average measurements at midpoint of voltage range, 25°C only.
3. Run (operating) IDD measured using internal clock generator module (fop= 2.0 MHz). VDD = 2.0 Vdc. All inputs 0.2 V from
rail. No dc loads. Less than 100 pF on all outputs. All ports configured as inputs. CL = 20 pF. OSC2 capacitance linearly
affects run IDD. Measured with all modules enabled.
4. Wait IDD measured using internal clock generator module, fop = 2.0 MHz. All inputs 0.2 V from rail; no dc loads; less than
100 pF on all outputs. C L = 20 pF. OSC2 capacitance linearly affects wait IDD. All ports configured as inputs.
5. Stop IDD measured with no port pins sourcing current, all modules disabled except as noted.
6. Pullups and pulldowns are disabled.
7. Maximum is highest voltage that POR is guaranteed.
8. Maximum is highest voltage that POR is possible.
9. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum
VDD is reached.
Advance Information
238
MC68HC908RF2 — Rev. 1
Preliminary Electrical Specifications
MOTOROLA
Preliminary Electrical Specifications
UHF Transmitter Module
17.9 UHF Transmitter Module
This subsection provides electrical specifications and timing definitions
for the UHF transmitter module.
17.9.1 UHF Module Electrical Characteristics
Unless otherwise specified:
•
VCC = 3 V
•
REXT = 12 kΩ
•
Operating temperature range (TA) = –40°C to 85°C
•
RF output frequency: fCarrier = 433.92 MHz
•
Reference frequency: fReference =13.56 MHz
•
OOK modulation selected
•
Output load is 50 Ω resistor (see Figure 17-4)
Values refer to the circuit shown in the recommended application
schematic (see Figure 16-4. Application Schematic in OOK
Modulation, 315-MHz and 434-MHz Frequency Bands).
Typical values reflect average measurement at VCC = 3 V, TA = 25°C.
NOTE:
Electrical characteristics shown at 125°C are for information only. These
values have not been tested.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Preliminary Electrical Specifications
239
Preliminary Electrical Specifications
Parameter
Test Conditions and Comments
Min
Typ
Max
Unit
TA ≤ 25°C
—
0.1
5
nA
TA = 60°C
—
7
30
nA
TA = 85°C
—
40
100
nA
TA = 125°C
—
800
1700
nA
315 and 434 MHz bands,
continuous wave, TA ≤ 85°C
—
11.6
13.5
mA
315 and 434 MHz bands,
DATA = 0, –40°C ≤ TA ≤ 125°C
—
4.4
6.0
mA
868 MHz band,
DATA = 0, –40°C ≤ TA ≤ 125°C
—
4.6
6.2
mA
315 and 434 MHz bands,
continuous wave, –40°C ≤ TA ≤ 125°C
—
11.6
14.9
mA
868 MHz band,
continuous wave, –40°C ≤ TA ≤ 125°C
—
11.8
15.1
mA
—
3
3.7
V
TA = –40°C
—
2.04
2.11
V
TA = –20°C
—
1.99
2.06
V
TA = 25°C
—
1.86
1.95
V
TA = 60°C
—
1.76
1.84
V
TA = 85°C
—
1.68
1.78
V
TA = 125°C
—
1.56
1.67
V
General Parameters
Supply current
in standby mode
Supply current
in transmission mode
Supply voltage
Shutdown voltage
threshold
RF Parameters (assuming a 50 Ω matching network connected to the D.U.T. output)
REXT value
Output power
12
—
21
kΩ
315 and 434 MHz bands,
with 50 Ω matching network
—
5
—
dBm
868 MHz band,
with 50 Ω matching network
—
1
—
dBm
315 and 434 MHz bands,
–40°C ≤ TA ≤ 125°C
–3
0
3
dBm
868 MHz band,
–40°C ≤ TA ≤ 125°C
–7
–3
0
dBm
— Continued —
Advance Information
240
MC68HC908RF2 — Rev. 1
Preliminary Electrical Specifications
MOTOROLA
Preliminary Electrical Specifications
UHF Transmitter Module
Parameter
Current and output power
variation vs REXT value
Harmonic 2 level
Harmonic 3 level
Spurious level
@ fCarrier ± f DATACLK
Spurious level
@ fCarrier ± f Reference
Spurious level
@ fCarrier/2
RF spectrum
Test Conditions and Comments
Min
Typ
Max
Unit
314 and 434 MHz bands,
with 50 Ω matching network
—
–0.35
—
dB/kΩ
mA/kΩ
315 and 434 MHz bands,
with 50 Ω matching network
—
–34
—
dBc
868 MHz band,
with 50 Ω matching network
—
–49
—
dBc
315 and 434 MHz bands
—
–23
–17
dBc
868 MHz band
—
–38
–27
dBc
315 and 434MHz bands,
with 50 Ω matching network
—
–32
—
dBc
868 MHz band,
with 50 Ω matching network
—
–57
—
dBc
315 and 434 MHz bands
—
–21
–15
dBc
868 MHz band
—
–48
–39
dBc
315 and 434 MHz bands
—
–36
–24
dBc
–29
–17
dBc
868 MHz band
315 MHz band
—
–37
–30
dBc
434 MHz band
—
–44
–34
dBc
868 MHz band
—
–37
–27
dBc
315 MHz bands
—
–62
–53
dBc
434 MHz bands
—
–80
–60
dBc
868 MHz band
—
–45
–39
dBc
434 MHz bands
See Figure 17-1, Figure 17-2,
and Figure 17-3
—
315 and 434 MHz bands,
±175 kHz from f Carrier
—
–75
–68
dBc/Hz
868 MHz band,
±175 kHz from f Carrier
—
–73
–66
dBc/Hz
fCarrier within 30 kHz from the final
value, crystal series resistor = 150 Ω
—
350
1500
µs
XTAL1 input capacitance
—
1
2
pF
Crystal resistance
—
40
200
Ω
Modulation depth
75
90
—
dBc
Data rate
—
—
10
kBd
Phase noise
PLL lock-in time,
tPLL_Lock_In
— Continued —
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Preliminary Electrical Specifications
241
Preliminary Electrical Specifications
Parameter
Test Conditions and Comments
Min
Typ
Max
Unit
0
—
0.3 x VCC
V
0.7 x VCC
—
VCC
V
—
—
150
mV
—
—
100
nA
—
180
—
kΩ
0
—
0.25 x VCC
V
0.75 x VCC
—
VCC
V
Microcontroller Interfaces
Input low voltage
Pins BAND, MODE,
ENABLE, and DATA
Input high voltage
Input hysteresis voltage
Pins BAND, MODE,
DATA @ high level
Input current
ENABLE pulldown resistor
DATACLK output
low voltage
C Load = 2 pF
DATACLK output
high voltage
DATACLK rising time
DATACLK falling time
DATACLK settling time,
tDATACLK_Settling
CLoad = 2 pF,
measured from 20% to 80%
of the voltage swing
—
250
500
ns
—
150
400
ns
45 < duty cycle fDATACLK < 55%
—
800
1800
µs
RESOLUTION
BANDWIDTH:
100 KHZ
RESOLUTION
BANDWIDTH:
30 KHZ
Figure 17-1. RF Spectrum at 434-MHz Frequency
Band Displayed with a 5-MHz Span
Advance Information
242
MC68HC908RF2 — Rev. 1
Preliminary Electrical Specifications
MOTOROLA
Preliminary Electrical Specifications
UHF Transmitter Module
Figure 17-2. RF Spectrum at 434-MHz Frequency Band
Displayed with a 50-MHz Span
Figure 17-3. RF Spectrum at 434-MHz Frequency Band
Displayed with a 1.5-GHz Span
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Preliminary Electrical Specifications
243
Preliminary Electrical Specifications
17.9.2 UHF Module Output Power Measurement
The RF output levels given in the 17.9.1 UHF Module Electrical
Characteristics are measured whith a 50-Ω load directly connected to
the pin RFOUT as shown in figure Figure 17-4. This wideband coupling
method gives results independant of the application.
VCC
IMPEDER: TDK MMZ1608Y102CTA00
RFOUT
RF OUTPUT
100 pF
50 Ω
Figure 17-4. Output Power Measurement Configurations
The configuration shown in Figure 17-5(a) provides a better efficiency
in terms of output power and harmonics rejection. Schematic in
Figure 17-5(b) gives the equivalent circuit of the pin RFOUT and
impeder as well as the matching network components for 434-MHz
frequency band.
NOTE:
Note that the impeder is moved to the load side to decrease its influence
(similar to dc bias through the antenna).
Figure 17-6 gives the output power versus the REXT resistor value, in
both cases with 50-Ω load and with matching network.
Advance Information
244
MC68HC908RF2 — Rev. 1
Preliminary Electrical Specifications
MOTOROLA
Preliminary Electrical Specifications
UHF Transmitter Module
VCC
IMPEDER: TDK MMZ1608Y102CTA00
RFOUT
RF OUTPUT
MATCHING
NETWORK
(a)
50 Ω
MATCHING
NETWORK
330 pF
L1
C3
39 nH
(b)
50 Ω
3 kΩ
C0
R0
1.5 pF
250 Ω
RFOUT PIN
RI
RL
IMPEDER
LOAD
Figure 17-5. Ouput Characteristic and Matching Network for 434-MHz Frequency Band
OUTPUT POWER MEASUREMENT IN TYPICAL CONDITIONS
(434 MHz – VCC = 3 V –25°C)
REXT SPECIFIED RANGE
8
6
OUTPUT POWER WHEN MATCHED (dBm)
–0.35 db/kΩ # –0.35 mA/kΩ
RFOUT LEVEL (dBm)
4
2
0
–2
–4
OUTPUT POWER ON 50 Ω LOAD (dBm)
–6
6
9
12
15
REXT (kΩ)
18
21
24
Figure 17-6. Output Power at 434-MHz Frequency Band versus REXT Value
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Preliminary Electrical Specifications
245
Preliminary Electrical Specifications
17.10 Control Timing
Characteristic
Symbol
Min
Max
Unit
Bus operating frequency
VDD = 3.0 V ± 10%
VDD = 2.0 V ± 10%
fBus
32 k
32 k
4.0 M
2.0 M
Hz
RESET pulse width low
tRL
1.5
—
tcyc
IRQ interrupt pulse width low (edge-triggered)
tILHI
1.5
—
tcyc
IRQ interrupt pulse period
tILIL
Note 4
—
tcyc
tTH, tTL
tTLTL
tTCH, tTCL
2
Note 4
(1/fOP) + 5
—
—
—
tcyc
tcyc
ns
16-bit timer (Note 2)
Input capture pulse width (Note 3)
Input capture period
Input clock pulse width
Notes:
1. VDD = 1.8 V to 3.3 V, VSS = 0 Vdc, TA = –40oC to +85oC, unless otherwise noted
2. The 2-bit timer prescaler is the limiting factor in determining timer resolution.
3. Refer to Table 15-3. Mode, Edge, and Level Selection and supporting note.
4. The minimum period tTLTL or tILIL should not be less than the number of cycles it takes to execute the capture interrupt
service routine plus 2 tcyc.
17.11 Internal Oscillator Characteristics
Characteristic(1)
Internal oscillator base frequency without
trim(2) (3)
Internal oscillator base frequency
with trim(2) (3)
Internal oscillator multiplier(4)
External clock option(5)
3 V ± 10%
2 V ± 10%
Symbol
Min
Typ
Max
Unit
fINTOSC
230.4
307.2
384.0
kHz
fINTOSC(I)
291.8
307.2
322.6
kHz
N
1
—
127
—
fEXTOSC
128 k
128 k
—
—
16
8
MHz
1. VDD = 1.8 V to 3.3 V, VSS = 0 Vdc, TA = –40oC to +85oC, unless otherwise noted
2. Internal oscillator is selectable through software for a maximum frequency. Actual frequency will be multiplier (N) x base
frequency.
3. fBus = (fINTOSC / 4) x (internal oscillator multiplier)
4. Multiplier must be chosen to limit the maximum bus frequency to the maximum listed in 17.10 Control Timing.
5. No more than 10% duty cycle deviation from 50%
Advance Information
246
MC68HC908RF2 — Rev. 1
Preliminary Electrical Specifications
MOTOROLA
Preliminary Electrical Specifications
LVI Characteristics
17.12 LVI Characteristics
Characteristic(1)
Symbol
Min
Typ
Max
Unit
LVI low battery sense voltage(1)
VLVS
1.90
2.00
2.15
V
LVI trip voltage(1)
VLVR
1.76
1.85
2.00
V
LVI trip voltage hysteresis
HLVR
50
70
90
mV
VDD slew rate — rising
SRR
—
—
0.05
V/µs
VDD slew rate — falling
SRF
—
—
0.10
V/µs
Response time — SR ≤ SRmax
tresp
—
—
6.0
µs
Response time — SR > SR max
tresp
—
—
See Note 2
µs
ten
—
—
50
µs
Enable time (enable to output transition)
1. The LVI samples VDD, VLVR, and VLVS are VDD voltages.
2.  V DD – V LVR V DD – V LVR
 ----------------------------------- – ----------------------------------- + 1.5
SR
 SR max

MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Preliminary Electrical Specifications
247
Preliminary Electrical Specifications
17.13 Memory Characteristics
Characteristic
Symbol
Min
Typ
Max
Unit
VRDR
1.3
—
—
V
FLASH pages per row
—
8
—
8
Pages
FLASH bytes per page
—
1
—
1
Bytes
FLASH read bus clock frequency
fRead(1)
32 K
—
2.5 M
Hz
FLASH charge pump clock frequency
(see 4.5 FLASH 2TS Charge Pump Frequency
Control)
fPump(2)
1.8
—
2.5
MHz
tErase
100
—
—
ms
tRowErase
30
—
—
ms
tKill
200
—
—
µs
tHVD
50
—
—
µs
flsPulses(3)
—
—
15
Pulses
FLASH page program step size
tStep(4)
1.0
—
1.2
ms
FLASH cumulative program time per row between
erase cycles
tRow(5)
—
—
8
Page
program
cycles
FLASH HVEN low to MARGIN high time
tHVTV
50
—
—
µs
FLASH MARGIN high to PGM low time
tVTP
150
—
—
µs
FLASH 2TS row program endurance(6)
—
104
-—
-—
Cycles
FLASH data retention time(7)
—
10
-—
-—
Years
RAM data retention voltage
FLASH block/bulk erase time
FLASH row erase time
FLASH high voltage kill time
FLASH return to read time
FLASH page program pulses
1.
2.
3.
4.
5.
fRead is defined as the frequency range for which the FLASH memory can be read.
fPump is defined as the charge pump clock frequency required for program, erase, and margin read operations.
flsPulses is defined as the number of pulses used to program the FLASH using the required smart program algorithm.
tStep is defined as the amount of time during one page program cycle that HVEN is held high.
tRow is defined as the cumulative time a row can see the program voltage before the row must be erased before further
programming.
6. The minimum row endurance value specifies each row of the FLASH 2TS memory is guaranteed to work for at least this
many erase/program cycles.
7. The FLASH is guaranteed to retain data over the entire temperature range for at least the minimum time specified.
Advance Information
248
MC68HC908RF2 — Rev. 1
Preliminary Electrical Specifications
MOTOROLA
Advance Information — MC68HC908RF2
Section 18. Mechanical Specifications
18.1 Contents
18.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
18.3
32-Pin LQFP Package (Case No. 873A) . . . . . . . . . . . . . . . . 250
18.2 Introduction
This section gives dimensions for the 32-pin low-profile quad flat pack
(LQFP).
The following figure shows the latest package drawing at the time of this
publication. To make sure that you have the latest package
specifications, contact one of the following:
•
Local Motorola Sales Office
•
Worldwide Web (wwweb) at http://www.motorola.com/mcu/
Follow Worldwide Web on-line instructions to retrieve the current
mechanical specifications.
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Mechanical Specifications
249
Mechanical Specifications
A
–T–, –U–, –Z–
18.3 32-Pin LQFP Package (Case No. 873A)
4X
A1
32
0.20 (0.008) AB T–U Z
25
1
–U–
–T–
B
V
AE
P
B1
DETAIL Y
17
8
V1
AE
DETAIL Y
9
4X
–Z–
9
0.20 (0.008) AC T–U Z
S1
S
DETAIL AD
G
–AB–
0.10 (0.004) AC
AC T–U Z
–AC–
BASE
METAL
ÉÉ
ÉÉ
ÉÉ
ÉÉ
F
8X
M_
R
J
M
N
D
0.20 (0.008)
SEATING
PLANE
SECTION AE–AE
W
K
X
DETAIL AD
Q_
GAUGE PLANE
H
0.250 (0.010)
C E
Advance Information
250
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE –AB– IS LOCATED AT BOTTOM
OF LEAD AND IS COINCIDENT WITH THE LEAD
WHERE THE LEAD EXITS THE PLASTIC BODY AT
THE BOTTOM OF THE PARTING LINE.
4. DATUMS –T–, –U–, AND –Z– TO BE DETERMINED
AT DATUM PLANE –AB–.
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE –AC–.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS
0.250 (0.010) PER SIDE. DIMENSIONS A AND B
DO INCLUDE MOLD MISMATCH AND ARE
DETERMINED AT DATUM PLANE –AB–.
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. DAMBAR PROTRUSION SHALL
NOT CAUSE THE D DIMENSION TO EXCEED
0.520 (0.020).
8. MINIMUM SOLDER PLATE THICKNESS SHALL BE
0.0076 (0.0003).
9. EXACT SHAPE OF EACH CORNER MAY VARY
FROM DEPICTION.
DIM
A
A1
B
B1
C
D
E
F
G
H
J
K
M
N
P
Q
R
S
S1
V
V1
W
X
MILLIMETERS
MIN
MAX
7.000 BSC
3.500 BSC
7.000 BSC
3.500 BSC
1.400
1.600
0.300
0.450
1.350
1.450
0.300
0.400
0.800 BSC
0.050
0.150
0.090
0.200
0.500
0.700
12_ REF
0.090
0.160
0.400 BSC
1_
5_
0.150
0.250
9.000 BSC
4.500 BSC
9.000 BSC
4.500 BSC
0.200 REF
1.000 REF
INCHES
MIN
MAX
0.276 BSC
0.138 BSC
0.276 BSC
0.138 BSC
0.055
0.063
0.012
0.018
0.053
0.057
0.012
0.016
0.031 BSC
0.002
0.006
0.004
0.008
0.020
0.028
12_ REF
0.004
0.006
0.016 BSC
1_
5_
0.006
0.010
0.354 BSC
0.177 BSC
0.354 BSC
0.177 BSC
0.008 REF
0.039 REF
MC68HC908RF2 — Rev. 1
Mechanical Specifications
MOTOROLA
Advance Information — MC68HC908RF2
Section 19. Ordering Information
19.1 Contents
19.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
19.3
MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251
19.2 Introduction
This section contains ordering numbers for the MC68HC908RF2.
19.3 MC Order Numbers
Table 19-1. MC Order Numbers
MC Order Number(1)
MC68HC908RF2CFA
Operating
Temperature Range
–40°C to +85°C
1. FA = Low-profile quad flat pack (LQFP)
MC68HC908RF2 — Rev. 1
MOTOROLA
Advance Information
Ordering Information
251
Ordering Information
Advance Information
252
MC68HC908RF2 — Rev. 1
Ordering Information
MOTOROLA
blank
USA/EUROPE/LOCATIONS NOT LISTED:
Motorola Literature Distribution
P.O. Box 5405
Denver, Colorado 80217
1-303-675-2140
1-800-441-2447
TECHNICAL INFORMATION CENTER:
1-800-521-6274
JAPAN:
Motorola Japan Ltd.
SPS, Technical Information Center
3-20-1, Minami-Azabu, Minato-ku
Tokyo 106-8573 Japan
81-3-3440-3569
MC68HC08AS60 Technical Data
How to Reach Us:
ASIA/PACIFIC:
Motorola Semiconductors H.K. Ltd.
Silicon Harbour Centre
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
852-26668334
HOME PAGE:
http://www.motorola.com/semiconductors/
MC68HC908RF2/D
REV 1
Q4/00
REV 1