SEMICONDUCTOR TECHNICAL DATA ' $ %$ $ "#!"$ $ ' " % %$ $$ &"$ The MC74LVQ573 is a high performance, non–inverting octal transparent latch operating from a 2.7 to 3.6V supply. The MC74LVQ573 is suitable for TTL level bus oriented applications where a memory element is required. The MC74LCX573 contains 8 D–type latches with 3–state standard outputs. When the Latch Enable (LE) input is HIGH, data on the Dn inputs enters the latches. In this condition, the latches are transparent, i.e., a latch output will change state each time its D input changes. When LE is LOW, the latches store the information that was present on the D inputs a setup time preceding the HIGH–to–LOW transition of LE. The 3–state standard outputs are controlled by the Output Enable (OE) input. When OE is LOW, the standard outputs are enabled. When OE is HIGH, the standard outputs are in the high impedance state, but this does not interfere with new data entering into the latches. The LCX573 flow through design facilitates easy PC board layout. LVQ LOW–VOLTAGE CMOS OCTAL TRANSPARENT LATCH DW SUFFIX PLASTIC SOIC CASE 751D–04 20 1 • Designed for 2.7 to 3.6V VCC Operation – Ideal for Low Power/Low Noise Applications • Guaranteed Simultaneous Switching Noise Level and Dynamic M SUFFIX PLASTIC SOIC EIAJ CASE 967–01 20 Threshold Performance • Guaranteed Skew Specifications 1 • Guaranteed Incident Wave Switching into 75Ω • Low Static Supply Current (10µA) Substantially Reduces System Power Requirements • Latchup Performance Exceeds 500mA 20 1 SD SUFFIX PLASTIC SSOP CASE 940C–03 • ESD Performance: Human Body Model >2000V Pinout: 20–Lead (Top View) 20 VCC O0 O1 O2 O3 O4 O5 O6 O7 LE 20 19 18 17 16 15 14 13 12 11 1 DT SUFFIX PLASTIC TSSOP CASE 948E–02 PIN NAMES 1 2 3 4 5 6 7 8 9 10 OE D0 D1 D2 D3 D4 D5 D6 D7 GND Pins Function OE LE D0–D7 O0–O7 Output Enable Input Latch Enable Input Data Inputs 3–State Latch Outputs 11/95 Motorola, Inc. 1995 1 REV 0 MC74LVQ573 LOGIC DIAGRAM OE LE 1 11 2 D0 D1 18 nLE O1 Q D 4 D2 17 nLE O2 Q D 5 D3 16 nLE O3 Q D 6 D4 15 nLE O4 Q D 7 D5 14 nLE O5 Q D 8 D6 13 nLE O6 Q D 9 D7 OE O0 Q D 3 INPUTS 19 nLE 12 nLE Q O7 D INTERNAL LATCHES OUTPUTS LE Dn Q On OPERATING MODE H L H L Transparent (Latch Disabled); Read Latch L L H H L L H L h l H L H L Latched (Latch Enabled) Read Latch L L L L X NC NC Hold; Read Latch H L X NC Z Hold; Disabled Outputs H H H H H L H L Z Z Transparent (Latch Disabled); Disabled Outputs H H L L h l H L Z Z Latched (Latch Enabled); Disabled Outputs H = High Voltage Level; h = High Voltage Level One Setup Time Prior to the Latch Enable High–to–Low Transition; L = Low Voltage Level; l = Low Voltage Level One Setup Time Prior to the Latch Enable High–to–Low Transition; NC = No Change; X = High or Low Voltage Level and Transitions are Acceptable; Z = High Impedance State; For ICC Reasons DO NOT FLOAT Inputs MOTOROLA 2 ECLinPS and ECLinPS Lite DL140 — Rev 3 MC74LVQ573 ABSOLUTE MAXIMUM RATINGS* Symbol Parameter VCC DC Supply Voltage VI Value Condition Unit –0.5 to +7.0 V DC Input Voltage –0.5 ≤ VI ≤ VCC + 0.5V V VO DC Output Voltage –0.5 ≤ VO ≤ VCC + 0.5 Output in HIGH or LOW State V IIK DC Input Diode Current –20 VI = –0.5V mA +20 VI = VCC + 0.5V mA –20 VO = –0.5V mA +20 VI = VCC + 0.5V mA IOK DC Output Diode Current IO DC Output Source/Sink Current ±50 mA ICC DC Supply Current ±400 mA IGND DC Ground Current ±400 mA TSTG Storage Temperature Range –65 to +150 °C * Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute–maximum–rated conditions is not implied. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage VI Input Voltage VO Output Voltage TA Operating Free–Air Temperature ∆V/∆t Input Transition Rise or Fall Rate, VIN from 0.8V to 2.0V, VCC = 3.0V Min Typ Max Unit 2.0 3.3 3.6 V 0 VCC V 0 VCC V –40 +85 °C 0 125 mV/ns DC ELECTRICAL CHARACTERISTICS TA = –40°C to +85°C Symbol Characteristic Condition Min 2.0 VIH HIGH Level Input Voltage (Note 1) 2.7V ≤ VCC ≤ 3.6V, VO = 0.1V or VCC – 0.1V VIL LOW Level Input Voltage (Note 1) 2.7V ≤ VCC ≤ 3.6V, VO = 0.1V or VCC – 0.1V VOH HIGH Level Output Voltage VOL LOW Level Output Voltage II Input Leakage Current IOZ Maximum 3–State Leakage Current IOLD Minimum Dynamic Output Current (Note 2) IOHD ICC Quiescent Supply Current Max V 0.8 2.7V ≤ VCC ≤ 3.6V; IOH = –50µA VCC – 0.1 VCC = 2.7V; IOH = –12mA 2.2 VCC = 3.0V; IOH = –12mA 2.48 Unit V V 2.7V ≤ VCC ≤ 3.6V; IOL = 50µA 0.1 2.7V ≤ VCC ≤ 3.6V; IOL= 12mA 0.4 2.7V ≤ VCC ≤3.6V; VI= VCC, GND ±1.0 µA VI(OE) = VIL, VIH; VI, VO= VCC, GND ±2.5 µA VCC = 3.6V; VOLD = 0.8V Max 36 mA VCC = 3.6V; VOHD = 2.0V Min –25 mA 2.7V ≤ VCC ≤3.6V; VI = VCC, GND 10 µA V 1. These values of VI are used to test DC electrical characteristics only. Functional test should use VIH ≥ 2.4V, VIL ≤ 0.5V. 2. Incident wave switching on transmission lines with impedances as low as 75Ω for commercial temperature range is guaranteed. Maximum test duration is 2ms, one output loaded at a time. ECLinPS and ECLinPS Lite DL140 — Rev 3 3 MOTOROLA MC74LVQ573 DYNAMIC SWITCHING CHARACTERISTICS (VCC = 3.3V) TA = +25°C Symbol Characteristic Condition VOLP Dynamic LOW Peak Voltage (Note 1) VOLV Dynamic LOW Valley Voltage (Note 1) VIHD VILD Min Typ Max Unit CL = 50pF, VIH = 3.3V, VIL = 0V 0.6 1.0 V CL = 50pF, VIH = 3.3V, VIL = 0V –0.5 –1.0 V High Level Dynamic Input Voltage (Note 2) Input–Under–Test Switching 0V to Threshold, f=1MHz 1.5 2.0 V Low Level Dynamic Input Voltage (Note 2) Input–Under–Test Switching 3.3V to Threshold, f=1MHz 1.5 0.8 V 1. Number of outputs defined as “n”. Measured with “n–1” outputs switching from HIGH–to–LOW. The remaining output is measured in the LOW state. 2. Number of data inputs is defined as “n” switching, “n–1” inputs switching 0V to 3.3V. AC CHARACTERISTICS (tR = tF = 2.5ns; CL = 50pF; RL = 500Ω) Limits TA = +25°C VCC = 3.0V to 3.6V Symbol Parameter TA = –40°C to +85°C VCC = 2.7V VCC = 3.0V to 3.6V VCC = 2.7V Min Typ Max Min Typ Max Min Max Max Unit tPLH tPHL Propagation Delay Dn to On 2.5 2.5 10.0 8.5 12.0 10.5 2.5 2.5 11.0 9.5 14.0 12.5 2.5 2.5 13.0 11.5 16.0 14.0 ns tPLH tPHL Propagation Delay LE to On 2.5 2.5 10.0 8.5 12.5 11.0 2.5 2.5 11.0 10.0 14.5 13.5 2.5 2.5 13.5 12.0 15.5 14.5 ns tPZH tPZL Output Enable Time to High and Low Level 2.5 2.5 8.0 8.0 10.0 10.0 2.5 2.5 9.0 9.0 11.5 11.5 2.5 2.5 10.5 10.5 12.0 12.0 ns tPHZ tPLZ Output Disable Time From High and Low Level 1.0 1.0 9.5 6.5 12.0 9.0 1.0 1.0 11.0 7.0 13.5 10.0 1.0 1.0 12.5 10.0 14.5 11.0 ns tOSHL tOSLH Output–to–Output Skew (Note 1) 1.0 1.0 1.5 1.5 1.0 1.0 1.5 1.5 1.5 1.5 ns 1. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter guaranteed by design. AC OPERATING REQUIREMENTS (tR = tF = 2.5ns; CL = 50pF; RL = 500Ω) Limits TA = +25°C Symbol TA = –40°C to +85°C VCC = 3.0V to 3.6V VCC = 2.7V VCC = 3.0V to 3.6V VCC = 2.7V Parameter Min Min Min Min Unit ts Setup TIme, HIGH or LOW Dn to LE 3.0 4.0 3.0 4.5 ns th Hold TIme, HIGH or LOW Dn to LE 1.5 1.5 1.5 1.5 ns tw LE Pulse Width, HIGH 4.0 5.0 4.0 6.0 ns CAPACITIVE CHARACTERISTICS Symbol Parameter CPD Power Dissipation Capacitance CIN Input Capacitance MOTOROLA Condition Typical Unit 10MHz, VCC = 3.3V, VI = 0V or VCC 30 pF VCC = Open, VI = 0V or VCC 4.5 pF 4 ECLinPS and ECLinPS Lite DL140 — Rev 3 MC74LVQ573 VCC Dn 50% VCC 50% VCC 0V tPLH tPHL VOH 50% VCC On 50% VCC VOL WAVEFORM 1 – PROPAGATION DELAYS tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns VCC Dn 50% VCC 50% VCC OE VCC 50% VCC 50% VCC 0V tPZH 0V ts tPHZ VCC VOH – 0.3V VCC LE 50% VCC On th tw 50% VCC 50% VCC ≈ 0V 0V tPLH, tPHL tPZL On tPLZ ≈ 3.0V VOH On 50% VCC 50% VCC VOL VOL + 0.3V GND WAVEFORM 3 – LE to On PROPAGATION DELAYS, LE MINIMUM PULSE WIDTH, Dn to LE SETUP AND HOLD TIMES tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns except when noted WAVEFORM 2 – OUTPUT ENABLE AND DISABLE TIMES tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns Figure 1. AC Waveforms VCC 2 • VCC PULSE GENERATOR R1 DUT CL RT TEST OPEN RL SWITCH tPLH, tPHL Open tPZL, tPLZ 2 • VCC Open Collector/Drain tPLH and tPHL 2 • VCC tPZH, tPHZ Open CL = 50pF or equivalent (Includes jig and probe capacitance) RL = R1 = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) Figure 2. Test Circuit ECLinPS and ECLinPS Lite DL140 — Rev 3 5 MOTOROLA MC74LVQ573 OUTLINE DIMENSIONS DW SUFFIX PLASTIC SOIC PACKAGE CASE 751D–04 ISSUE E –A – 20 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.150 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. 11 1 –B – P 10 PL A B 0.010 (0.25) B M M 10 D 20 PL J 0.010 (0.25) M T S S DIM A B C D F G J K M P R F R X 45° C –T G 18 PL M SEATING – PLANE K MILLIMETERS MIN MAX 12.65 12.95 7.40 7.60 2.35 2.65 0.35 0.49 0.50 0.90 1.27 BSC 0.25 0.32 0.10 0.25 0° 7° 10.05 10.55 0.25 0.75 INCHES MIN MAX 0.499 0.510 0.292 0.299 0.093 0.104 0.014 0.019 0.020 0.035 0.050 BSC 0.010 0.012 0.004 0.009 0° 7° 0.395 0.415 0.010 0.029 M SUFFIX PLASTIC SOIC EIAJ PACKAGE CASE 967–01 ISSUE O 20 NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5 THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 11 Q1 E HE M_ L 10 1 DETAIL P Z D e VIEW P A c A1 b 0.13 (0.005) MOTOROLA M 0.10 (0.004) 6 DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 12.35 12.80 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --0.81 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.486 0.504 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.032 ECLinPS and ECLinPS Lite DL140 — Rev 3 MC74LVQ573 OUTLINE DIMENSIONS SD SUFFIX PLASTIC SSOP PACKAGE CASE 940C–03 ISSUE B 20X K REF 0.12 (0.005) T U M V S S 0.25 (0.010) N 20 L/2 11 M N B L ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ ÇÇÇ ÉÉÉ ÇÇÇ ÉÉÉ F PIN 1 IDENT 1 10 DETAIL E K –U– A –V– 0.20 (0.008) M J T U S NOTES: 13 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 14 CONTROLLING DIMENSION: MILLIMETER. 15 DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 16 DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 17 DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION/INTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF K DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR INTRUSION SHALL NOT REDUCE DIMENSION K BY MORE THAN 0.07 (0.002) AT LEAST MATERIAL CONDITION. 18 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 19 DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. J1 DIM A B C D F G H J J1 K K1 L M K1 SECTION N–N 0.076 (0.003) –T– –W– C SEATING PLANE D G DETAIL E H 20X 0.15 (0.006) T U K REF M T U S V ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ S K K1 2X L/2 20 11 J J1 B L –U– PIN 1 IDENT SECTION N–N 1 10 0.25 (0.010) N 0.15 (0.006) T U S NOTES: 6 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 7 CONTROLLING DIMENSION: MILLIMETER. 8 DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 9 DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 10 DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 11 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 12 DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. M A –V– N F DETAIL E –W– C D G INCHES MIN MAX 0.278 0.288 0.205 0.212 0.068 0.078 0.002 0.008 0.024 0.037 0.026 BSC 0.023 0.030 0.003 0.008 0.003 0.006 0.010 0.015 0.010 0.013 0.301 0.311 0_ 8_ DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948E–02 ISSUE A 0.10 (0.004) S MILLIMETERS MIN MAX 7.07 7.33 5.20 5.38 1.73 1.99 0.05 0.21 0.63 0.95 0.65 BSC 0.59 0.75 0.09 0.20 0.09 0.16 0.25 0.38 0.25 0.33 7.65 7.90 0_ 8_ H DETAIL E 0.100 (0.004) –T– SEATING DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 1.20 ––– 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.252 0.260 0.169 0.177 0.047 ––– 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ PLANE ECLinPS and ECLinPS Lite DL140 — Rev 3 7 MOTOROLA MC74LVQ573 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] –TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 8 *MC74LVQ573/D* MC74LVQ573/D ECLinPS and ECLinPS Lite DL140 — Rev 3