ONSEMI 317B

Order this document by LM317/D
The LM317 is an adjustable 3–terminal positive voltage regulator capable
of supplying in excess of 1.5 A over an output voltage range of 1.2 V to 37 V.
This voltage regulator is exceptionally easy to use and requires only two
external resistors to set the output voltage. Further, it employs internal
current limiting, thermal shutdown and safe area compensation, making it
essentially blow–out proof.
The LM317 serves a wide variety of applications including local, on card
regulation. This device can also be used to make a programmable output
regulator, or by connecting a fixed resistor between the adjustment and
output, the LM317 can be used as a precision current regulator.
• Output Current in Excess of 1.5 A
•
•
•
•
•
•
•
THREE–TERMINAL
ADJUSTABLE POSITIVE
VOLTAGE REGULATOR
SEMICONDUCTOR
TECHNICAL DATA
Output Adjustable between 1.2 V and 37 V
Internal Thermal Overload Protection
Internal Short Circuit Current Limiting Constant with Temperature
Output Transistor Safe–Area Compensation
Floating Operation for High Voltage Applications
Available in Surface Mount D2PAK, and Standard 3–Lead Transistor
Package
Eliminates Stocking many Fixed Voltages
T SUFFIX
PLASTIC PACKAGE
CASE 221A
Heatsink surface
connected to Pin 2.
1
2
3
Pin 1. Adjust
2. Vout
3. Vin
Standard Application
Vin
Vout
LM317
R1
240
IAdj
Adjust
Cin*
0.1 µF
+ C **
O
1.0 µF
R2
1
2
3
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
ǒ Ǔ
** Cin is required if regulator is located an appreciable distance from power supply filter.
** CO is not needed for stability, however, it does improve transient response.
V out
D2T SUFFIX
PLASTIC PACKAGE
CASE 936
(D2PAK)
+ 1.25 V 1 ) R ) IAdj R2
R2
1
Since IAdj is controlled to less than 100 µA, the error associated with this term is
negligible in most applications.
ORDERING INFORMATION
Device
LM317BD2T
LM317BT
Operating
Temperature Range
TJ = – 40° to +125°C
LM317D2T
LM317T
Surface Mount
Insertion Mount
Surface Mount
TJ = 0° to +125°C
 Motorola, Inc. 1996
MOTOROLA ANALOG IC DEVICE DATA
Package
Insertion Mount
Rev 1
1
LM317
MAXIMUM RATINGS
Rating
Input–Output Voltage Differential
Symbol
Value
Unit
VI–VO
40
Vdc
PD
θJA
θJC
Internally Limited
65
5.0
W
°C/W
°C/W
PD
θJA
θJC
Internally Limited
70
5.0
W
°C/W
°C/W
TJ
– 40 to +125
°C
Tstg
– 65 to +150
°C
Power Dissipation
Case 221A
TA = +25°C
Thermal Resistance, Junction–to–Ambient
Thermal Resistance, Junction–to–Case
Case 936 (D2PAK)
TA = +25°C
Thermal Resistance, Junction–to–Ambient
Thermal Resistance, Junction–to–Case
Operating Junction Temperature Range
Storage Temperature Range
ELECTRICAL CHARACTERISTICS (VI–VO = 5.0 V; IO = 0.5 A for D2T and T packages; TJ = Tlow to Thigh [Note 1]; Imax and Pmax
[Note 2]; unless otherwise noted.)
Characteristics
Figure
Symbol
Min
Typ
Max
Unit
Line Regulation (Note 3), TA = +25°C, 3.0 V ≤ VI–VO ≤ 40 V
1
Regline
–
0.01
0.04
%/V
Load Regulation (Note 3), TA = +25°C, 10 mA ≤ IO ≤ Imax
VO ≤ 5.0 V
VO ≥ 5.0 V
2
Regload
–
–
5.0
0.1
25
0.5
mV
% VO
Regtherm
–
0.03
0.07
% VO/W
3
IAdj
–
50
100
µA
1, 2
∆IAdj
–
0.2
5.0
µA
Reference Voltage, 3.0 V ≤ VI–VO ≤ 40 V,
10 mA ≤ IO ≤ Imax, PD ≤ Pmax
3
Vref
1.2
1.25
1.3
V
Line Regulation (Note 3), 3.0 V ≤ VI–VO ≤ 40 V
1
Regline
–
0.02
0.07
%V
Load Regulation (Note 3), 10 mA ≤ IO ≤ Imax
VO ≤ 5.0 V
VO ≥ 5.0 V
2
Regload
–
–
20
0.3
70
1.5
mV
% VO
Temperature Stability (Tlow ≤ TJ ≤ Thigh)
3
TS
–
0.7
–
% VO
Minimum Load Current to Maintain Regulation (VI–VO = 40 V)
3
ILmin
–
3.5
10
mA
Maximum Output Current
VI–VO ≤ 15 V, PD ≤ Pmax, T Package
VI–VO = 40 V, PD ≤ Pmax, TA = +25°C, T Package
3
Imax
1.5
0.15
2.2
0.4
–
–
–
0.003
–
–
66
65
80
–
–
S
–
0.3
1.0
%/1.0 k
Hrs.
RθJC
–
5.0
–
°C/W
Thermal Regulation, TA = +25°C (Note 6), 20 ms Pulse
Adjustment Pin Current
Adjustment Pin Current Change, 2.5 V ≤ VI–VO ≤ 40 V,
10 mA ≤ IL ≤ Imax, PD ≤ Pmax
RMS Noise, % of VO, TA = +25°C, 10 Hz ≤ f ≤ 10 kHz
N
Ripple Rejection, VO = 10 V, f = 120 Hz (Note 4)
Without CAdj
CAdj = 10 µF
4
Long–Term Stability, TJ = Thigh (Note 5), TA = +25°C for
Endpoint Measurements
3
Thermal Resistance Junction to Case, T Package
A
RR
% VO
dB
NOTES: 1. Tlow to Thigh = 0° to +125°C, for LM317T, D2T. Tlow to Thigh = – 40° to +125°C, for LM317BT, BD2T.
2. Imax = 1.5 A, Pmax = 20 W
3. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately.
Pulse testing with low duty cycle is used.
4. CAdj, when used, is connected between the adjustment pin and ground.
5. Since Long–Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average stability
from lot to lot.
6. Power dissipation within an IC voltage regulator produces a temperature gradient on the die, affecting individual IC components on the die. These
effects can be minimized by proper integrated circuit design and layout techniques. Thermal Regulation is the effect of these temperature gradients
on the output voltage and is expressed in percentage of output change per watt of power change in a specified time.
2
MOTOROLA ANALOG IC DEVICE DATA
LM317
Representative Schematic Diagram
Vin
31
0
310
230
5.6k
120
6.3V
170
125k
160
12k
5.0pF
6.7k
13k
200
12.4k
6.8k
135
510
6.3V
30
pF
30
pF
2.4k
105
12.5k
4.0
6.3V
190
3.6k 5.8k
110
5.1k
0.1
Vout
Adjust
This device contains 29 active transistors.
Figure 1. Line Regulation and ∆IAdj/Line Test Circuit
VCC
ń +
VIH
VIL
*
|V
Line Regulation (% V)
–V |
OH OL
x 100
|V |
OL
VOH
VOL
Vout
Vin
LM317
* Pulse testing required.
* 1% Duty Cycle
* is suggested.
Adjust
Cin
0.1 µF
IAdj
R1
240
1%
+
CO
1.0 µF
RL
R2
1%
MOTOROLA ANALOG IC DEVICE DATA
3
LM317
Figure 2. Load Regulation and ∆IAdj/Load Test Circuit
VI
Vin
Vout
IL
LM317
Adjust
Cin
R1
RL
(max Load)
240
1%
*
+
0.1 µF
CO
IAdj
VO (min Load)
VO (max Load)
RL
(min Load)
1.0 µF
* Pulse testing required.
* 1% Duty Cycle is suggested.
R2
1%
Load Regulation (mV) = VO (min Load) – VO (max Load)
Load Regulation (% VO) =
VO (min Load) – VO (max Load)
x 100
VO (min Load)
Figure 3. Standard Test Circuit
Vin
Vout
LM317
IL
Adjust
R1
VI
Cin
0.1 µF
IAdj
240
1%
Vref
RL
+
CO
1.0 µF
VO
ISET
R2
1%
* Pulse testing required.
* 1% Duty Cycle is suggested.
To Calculate R2: Vout = ISET R2 + 1.250 V
To Calculate R2: Assume ISET = 5.25 mA
Figure 4. Ripple Rejection Test Circuit
24 V
Vout
Vin
14 V
f = 120 Hz
LM317
Adjust
Cin
240
1%
R1
0.1 µF
D1*
1N4002
CO
R2
1.65 k
1%
+
CAdj
RL
+
1.0 µF
Vout = 10 V
VO
10 µF
* D1 Discharges CAdj if output is shorted to Ground.
4
MOTOROLA ANALOG IC DEVICE DATA
LM317
Figure 5. Load Regulation
Figure 6. Current Limit
0.4
I out , OUTPUT CURRENT (A)
∆Vout, OUTPUT VOLTAGE CHANGE (%)
4.0
0.2
0
IL = 0.5 A
–0.2
IL = 1.5 A
–0.4
Vin = 15 V
Vout = 10 V
–0.6
3.0
TJ = 25°C
2.0
150°C
1.0
55°C
–0.8
–1.0
0
–50
–25
0
25
50
75
100
TJ, JUNCTION TEMPERATURE (°C)
125
150
0
10
20
30
Vin–Vout, INPUT–OUTPUT VOLTAGE DIFFERENTIAL (Vdc)
Figure 7. Adjustment Pin Current
40
Figure 8. Dropout Voltage
V in–Vout, INPUT–OUTPUT VOLTAGE
DIFFERENTIAL (Vdc)
I Adj, ADJUSTMENT PIN CURRENT ( µA)
3.0
70
65
60
55
50
45
40
35
–50
–25
0
25
50
75
100
125
∆Vout = 100 mV
1.0 A
2.0
500 mA
1.5
200 mA
20 mA
1.0
150
–50
–25
0
25
50
75
100
125
150
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 9. Temperature Stability
Figure 10. Minimum Operating Current
5.0
IB, QUIESCENT CURRENT (mA)
1.26
Vref, REFERENCE VOLTAGE (V)
IL = 1.5 A
2.5
1.25
1.24
1.23
4.5
TJ = –55°C
4.0
+25°C
3.5
+150°C
3.0
2.5
2.0
1.5
1.0
0.5
1.22
–50
–25
0
25
50
75 100 125
TJ, JUNCTION TEMPERATURE (°C)
MOTOROLA ANALOG IC DEVICE DATA
150
0
0
10
20
30
40
Vin–Vout, INPUT–OUTPUT VOLTAGE DIFFERENTIAL (Vdc)
5
LM317
Figure 12. Ripple Rejection versus
Output Current
Figure 11. Ripple Rejection versus Output Voltage
100
RR, RIPPLE REJECTION (dB)
CAdj = 10 µF
120
RR, RIPPLE REJECTION (dB)
80
Without CAdj
60
40
Vin – Vout = 5 V
IL = 500 mA
f = 120 Hz
TJ = 25°C
20
0
0
5.0
10
15
20
25
30
35
100
CAdj = 10 µF
80
Without CAdj
60
40
Vin = 15 V
Vout = 10 V
20 f = 120 Hz
TJ = 25°C
0
0.01
0.1
Vout, OUTPUT VOLTAGE (V)
101
Z O, OUTPUT IMPEDANCE ( Ω )
RR, RIPPLE REJECTION (dB)
IL = 500 mA
Vin = 15 V
Vout = 10 V
TJ = 25°C
80
60
40
20
CAdj = 10 µF
Without CAdj
100
1.0 k 10 k
100 k
Vin = 15 V
Vout = 10 V
IL = 500 mA
TJ = 25°C
100
10–1
Without CAdj
10–2
CAdj = 10 µF
10–3
0
1.0 M 10 M
10
100
1.0 k
∆Vout , OUTPUT
VOLTAGE DEVIATION (V)
Figure 15. Line Transient Response
1.5
1.0
CL = 1.0 µF;
CAdj = 10 µF
0.5
0
∆V in , INPUT
VOTLAGE CHANGE (V)
–0.5
Vout = 10 V
IL = 50 mA
TJ = 25°C
–1.0
–1.5
1.0
Vin
0
10
20
t, TIME (µs)
6
100 k
1.0 M
Figure 16. Load Transient Response
3.0
2.0
1.0
0
CL = 1.0 µF;
CAdj = 10 µF
–1.0
30
40
Vin = 15 V
Vout = 10 V
INL = 50 mA
TJ = 25°C
–2.0
CL = 0;
Without CAdj
–3.0
CL = 0;
Without CAdj
0.5
10 k
f, FREQUENCY (Hz)
IL , LOAD
CURRENT (A)
∆Vout , OUTPUT
VOLTAGE DEVIATION (V)
f, FREQUENCY (Hz)
0
10
Figure 14. Output Impedance
Figure 13. Ripple Rejection versus Frequency
100
10
1.0
IO, OUTPUT CURRENT (A)
1.5
1.0
IL
0.5
0
0
10
20
30
40
t, TIME (µs)
MOTOROLA ANALOG IC DEVICE DATA
LM317
APPLICATIONS INFORMATION
External Capacitors
A 0.1 µF disc or 1.0 µF tantalum input bypass capacitor
(Cin) is recommended to reduce the sensitivity to input line
impedance.
The adjustment terminal may be bypassed to ground to
improve ripple rejection. This capacitor (CAdj) prevents ripple
from being amplified as the output voltage is increased. A
10 µF capacitor should improve ripple rejection about 15 dB
at 120 Hz in a 10 V application.
Although the LM317 is stable with no output capacitance,
like any feedback circuit, certain values of external
capacitance can cause excessive ringing. An output
capacitance (CO) in the form of a 1.0 µF tantalum or 25 µF
aluminum electrolytic capacitor on the output swamps this
effect and insures stability.
Basic Circuit Operation
The LM317 is a 3–terminal floating regulator. In operation,
the LM317 develops and maintains a nominal 1.25 V
reference (Vref) between its output and adjustment terminals.
This reference voltage is converted to a programming current
(IPROG) by R1 (see Figure 17), and this constant current flows
through R2 to ground.
The regulated output voltage is given by:
V out
ǒ Ǔ
+ Vref 1 ) RR2 ) IAdj R2
1
Since the current from the adjustment terminal (IAdj)
represents an error term in the equation, the LM317 was
designed to control IAdj to less than 100 µA and keep it
constant. To do this, all quiescent operating current is
returned to the output terminal. This imposes the requirement
for a minimum load current. If the load current is less than this
minimum, the output voltage will rise.
Since the LM317 is a floating regulator, it is only the
voltage differential across the circuit which is important to
performance, and operation at high voltages with respect to
ground is possible.
Protection Diodes
When external capacitors are used with any IC regulator it
is sometimes necessary to add protection diodes to prevent
the capacitors from discharging through low current points
into the regulator.
Figure 18 shows the LM317 with the recommended
protection diodes for output voltages in excess of 25 V or high
capacitance values (CO > 25 µF, CAdj > 10 µF). Diode D1
prevents CO from discharging thru the IC during an input
short circuit. Diode D2 protects against capacitor CAdj
discharging through the IC during an output short circuit. The
combination of diodes D1 and D2 prevents CAdj from
discharging through the IC during an input short circuit.
Figure 17. Basic Circuit Configuration
Vin
Vout
LM317
Vout
+
R1
Vref
Adjust
IPROG
Figure 18. Voltage Regulator with Protection Diodes
D1
IAdj
R2
1N4002
Vout
Vref = 1.25 V Typical
Vin
Vout
3.5
JUNCTION-TO-AIR (°C/W)
R θ JA, THERMAL RESISTANCE
80
PD(max) for TA = +50°C
70
3.0
Free Air
Mounted
Vertically
60
2.0 oz. Copper
L
Minimum
Size Pad
50
40
RθJA
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
L
30
0
MOTOROLA ANALOG IC DEVICE DATA
5.0
10
15
20
L, LENGTH OF COPPER (mm)
25
2.5
2.0
1.5
+
R1
D2
CO
1N4002
CAdj
PD, MAXIMUM POWER DISSIPATION (W)
LM317
Load Regulation
The LM317 is capable of providing extremely good load
Cin
regulation, but a few precautions are needed to obtain
maximum performance. For best performance, the
Adjust
programming resistor (R1) should be connected as close to
R2
the regulator as possible to minimize line drops which
effectively appear in series with the reference, thereby
degrading regulation. The ground end of R2 can be returned
near the load ground to provide remote ground sensing and
improve load regulation.
Figure 19. D2PAK Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
1.0
30
7
LM317
Figure 20. ‘‘Laboratory’’ Power Supply with Adjustable Current Limit and Output Voltage
D6*
1N4002
Vin
32 V to 40 V
Vout1 RSC
LM317
(1)
Vin1
Vin2
Iout
Vout 2
LM317
(2)
240
0.1 µF
D1
1N4001
Adjust 1
1.0K
Current
Limit
Adjust
D2
1N4001
D5
IN4001
Adjust 2
5.0 k
+
Vout
+
1.0 µF
Tantalum
10 µF
Voltage
Adjust
1N4001
Q1
2N3822
* Diodes D1 and D2 and transistor Q2 are added to
* allow adjustment of output voltage to 0 V.
D3
Output Range: 0 ≤ VO ≤ 25 V
Output Range: 0 ≤ IO ≤ 1.5 A
D4
* D6 protects both LM317’s during an input short circuit.
–10 V
IN4001
Q2
2N5640
–10 V
Figure 21. Adjustable Current Limiter
Vout
+25 V
LM317
Vin
Figure 22. 5.0 V Electronic Shutdown Regulator
D1*
R1
Iout
1.25
Adjust
R2 ≤
Adjust
MPS2222
720
1.0 k
2N5640
Vref
IDDS
* D1 protects the device during an input short circuit.
Figure 23. Slow Turn–On Regulator
LM317
Vout
R1
Iout
LM317
240
Adjust
8
Figure 24. Current Regulator
Vin
Vout
R2
TTL
Control
Minimum Vout = 1.25 V
VSS*
VO < BVDSS + 1.25 V + VSS,
ILmin – IDSS < IO < 1.5 A.
As shown 0 < IO < 1.0 A.
Vin
+
1.0 µF
120
D2
1N4001
* To provide current limiting of IO to the system
* ground, the source of the FET must be tied to a
* negative voltage below – 1.25 V.
Vref
IOmax + IDSS
Vout
LM317
D1
1N4001
R2
100
R1 =
1N4002
Vin
1N4001
MPS2907
+
10 µF
ǒǓ
IAdj
Adjust
50 k
+
V
)
ref
I
Adj
R1
1.25 V
R1
10 mA ≤ Iout ≤ 1.5 A
I out
+
MOTOROLA ANALOG IC DEVICE DATA
LM317
OUTLINE DIMENSIONS
T SUFFIX
PLASTIC PACKAGE
CASE 221A–06
ISSUE Y
F
B
C
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIM Z DEFINES A ZONE WHERE ALL BODY AND
LEAD IRREGULARITIES ARE ALLOWED.
SEATING
PLANE
–T
–
T
S
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
4
A
Q
1 2 3
U
H
K
Z
L
R
V
J
G
D
INCHES
MIN
MAX
0.570 0.620
0.380 0.405
0.160 0.190
0.025 0.035
0.142 0.147
0.095 0.105
0.110 0.155
0.018 0.025
0.500 0.562
0.045 0.060
0.190 0.210
0.100 0.120
0.080 0.110
0.045 0.055
0.235 0.255
0.000 0.050
–
0.045
0.080
–
MILLIMETERS
MIN
MAX
14.48 15.75
9.66 10.28
4.82
4.07
0.88
0.64
3.73
3.61
2.66
2.42
3.93
2.80
0.64
0.46
12.70 14.27
1.52
1.15
5.33
4.83
3.04
2.54
2.79
2.04
1.39
1.15
6.47
5.97
1.27
0.00
–
1.15
2.04
–
N
D2T SUFFIX
PLASTIC PACKAGE
CASE 936–03
(D2PAK)
ISSUE B
OPTIONAL
CHAMFER
A
E
TERMINAL 4
–T
–
U
S
K
V
B
H
F
1
2
3
M
P
J
N
D
0.010 (0.254) M
L
R
T
G
C
MOTOROLA ANALOG IC DEVICE DATA
NOTES:
1 DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2 CONTROLLING DIMENSION: INCH.
3 TAB CONTOUR OPTIONAL WITHIN DIMENSIONS
A AND K.
4 DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 4.
5 DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.025 (0.635) MAXIMUM.
DIM
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
S
U
V
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.051 REF
0.100 BSC
0.539
0.579
0.125 MAX
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 _ REF
0.116 REF
0.200 MIN
0.250 MIN
MILLIMETERS
MIN
MAX
9.804 10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
1.295 REF
2.540 BSC
13.691 14.707
3.175 MAX
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 _ REF
2.946 REF
5.080 MIN
6.350 MIN
9
LM317
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,
Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488
Mfax: [email protected] – TOUCHTONE 602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
INTERNET: http://motorola.com/sps
10
◊
MOTOROLA ANALOG IC DEVICELM317/D
DATA