PS100R THRU PS1010R FAST SWITCHING PLASTIC DIODES VOLTAGE - 50 to 1000 Volts CURRENT - 1.0 Ampere FEATURES l High current capability l Plastic package has Underwriters Laboratory DO-41 l Flammability Classification 94V-O Utilizing Flame Retardant Epoxy Molding Compound 1.0 ampere operation at TA=55 ¢J with no thermal runaway l Fast switching for high efficiency l l Exceeds environmental standards of MIL-S-19500/228 Low leakage MECHANICAL DATA Case: Molded plastic, DO-41 Terminals: Plated axial leads, solderable per MIL-STD-202, Method 208 Polarity: Color band denotes cathode Mounting Position: Any Weight: 0.012 ounce, 0.3 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) lead length at TA=55 ¢J PS100R PS101R PS102R PS104R PS106R PS108R PS1010R UNITS 50 35 50 100 70 100 200 140 200 400 280 400 1.0 600 420 600 800 560 800 1000 700 1000 V V V A Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load(JECEC method) 30 A Maximum Forward Voltage at 1.0A DC Maximum Reverse Current TJ=25 ¢J at Rated DC Blocking Voltage TJ=100 ¢J Typical Junction capacitance (Note 1) CJ Typical Thermal Resistance (Note 3) R £KJA Maximum Reverse Recovery Time(Note 2) 1.3 5.0 500 V £g A £g A 150 150 Operating and Storage Temperature Range TJ,TSTG 150 12 41 150 250 -55 to +150 PF ¢J /W 500 500 NOTES: 1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC 2. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A 3. Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length P.C.B. mounted ns ¢J RATING AND CHARACTERISTIC CURVES PS100R THRU PS1010R trr +0.5A 0 -0.25 -1.0 NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. 1cm SET TIME BASE FOR 50 ns/cm Source Impedance = 50 Ohms Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 1 AVERAGE FORWARD RECTIFIED CURRENT AMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ = 25 ¢J 0.1 PULSE WIDTH = 300£gs 1% DUTY CYCLE 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.6 1.4 MAXIMUM AVERAGE CURRENT RATING SINGLE PHASE, HALF WAVE 60Hz 1.2 RESISTIVE OR INDUCTIVE LOAD .375"(9.5mm) LEAD LENGTHS 1.0 .8 .6 .4 .2 0 0 20 40 60 80 100 120 140 160 AMBIENT TEMPERATURE, ¢J INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS Fig. 3-FORWARD CURRENT DERATING CURVE FORWARD SURGE CURRENT, AMPERES pk (HALF-SINE WAVE) CAPACITANCE, pF 100 TJ = 25 ¢J 10 30 24 18 12 6 1 1 1 4 10 2 4 6 8 10 20 40 60 80 100 100 REVERSE VOLTAGE, Vdc Fig. 4-TYPICAL JUNCTION CAPACITANCE NUMBER OF CYCLES AT 60Hz Fig. 5-PEAK FORWARD SURGE CURRENT 180