1. DATA SHEET PS150R~PS1510R FAST SWITCHING PLASTIC RECTIFIER DO-15 VOLTAGE 50 to 1000 Volts CURRENT - 1.5 Amperes Unit: inch ( mm ) .034(.86) .028(.71) 1.0(25.4) MIN. FEATURES • High current capability. • Plastic package has Underwriters Laboratory Flammability Classification 94V-O utilizing Flame Retardant Epoxy Molding Compound. • Low leakage. • Exceeds environmental standards of MIL-S-19500/228 .300(7.6) .230(5.8) • 1.5 ampere operation at TA=55°C with no thermal runaway. • Fast switching for high efficiency. MECHANICAL DATA .140(3.6) .104(2.6) 1.0(25.4) MIN. Case: Molded plastic, DO-15 Terminals: Axial leads, solderable to MIL-STD-202,Method 208 Polarity: Color Band denotes cathode end Mounting Position: Any Weight: 0.015 ounce, 0.4 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. PS150R PS151R PS152R PS154R PS156R PS158R PS1510R UNIT Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 1000 V Maximum RMS Voltage 35 70 140 280 420 560 700 V Maximum DC Blocking Voltage 50 100 200 400 600 800 1000 V Maximum Average Forward Current .375"(9.5mm) 1.5 A Peak Forward Surge Current, IFM (surge):8.3ms single half sine-wave superimposed on rated load(JEDEC method) 50.0 A Maximum Forward Voltage at 1.5A 1.30 V 5.0 µA 500 µA lead length at TA=55°C Maximum Full Load Reverse Current Full Cycle Average ,.375”,9.5mm Lead Length at TA=25°C Maximum DC Reverse Current at Rated DC Blocking Voltage TA=100°C Maximum Reverse Recovery Time(Note 1) 150 250 500 ns Typical Junction capacitance (Note 2) 25 pF Typical Junction Resistance(Note 3) RθJA 45 °C/ W -55 to +150 °C Operating and Storage Temperature Range TJ NOTES:1. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 VDC 3. Thermal resistance from junction to ambient and from junction to lead length 0.375"(9.5mm) P.C.B. mounted DTAE : SEP.14.2002 PAGE . 1 RATING AND CHARACTERISTIC CURVES t rr +0.5A 10 Noninductive 50 Noninductive 0 (-) PULSE GENERATOR NOTE 2 (+) 25Vdc (approx) (-) -0.25 (+) 1 Non inductive OSCILLOSCCOPE NOTE 1 NOTES: 1.Rise Time=7ns max -1.0 Input Impedance=1 megohm. 22pF 1cm SET TIME BASE FOR10ns/cm 2. Rise Time=10ns max. Source Impedance = 50 Ohms Fig.1 -REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10 AVERAGE FORWARD CURRENT, AMPERES 1.50 IFM,Apk 1 0.1 1.00 0.75 .2 .4 .6 1.0 .8 1.2 1.6 SINGLE PGASE HALF WAVE 60HZ RESISTIVE OR INDUCTIVE LOAD .375" 9.5mm LEAD LENGTHS 0.50 0.25 0 0.01 0 25 50 75 100 125 150 175 1.8 FORWARD VOLTAGE - VFM(Vpk) AMBIENT TEMPERATURE, OC Fig.2 -FORWARD CHARACTERISTICS Fig.3 -FORWARD CURRENT DERATING CURVE 70 100 FORWARD SURGE CURRENT, AMPERES A CTIANCE, pF JUNCTION CAP 1.25 O T=25 C J f=1.0MHz Vsig=50mVp-p 40 20 10 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 60 50 40 30 20 10 100 .1 .5 1 5 10 20 50 100 REVERSE VOLTAGE, VOLTS MUNBER OF CYCLES AT 60Hz Fig.4 -TYPICAL JUNCTION CAPACITANCE VS. REVERSE VOLTAGE Fig.5 -PEAK FORWARD SURGE CURRENT DTAE : SEP.14.2002 PAGE . 2