S1D2502B01
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
VIDEO AMP MERGED OSD PROCESSOR
32-DIP-600A
The S1D2502B01 is a very high frequency video amplifier
& wide range OSD processor 1 chip system with I2C Bus
control used in monitors. It contains 3 matched R/G/B video
amplifiers with OSD processor and provides flexible
interfacing to I2C Bus controlled adjustment systems.
FUNCTIONS
•
R/G/B video amplifier
•
OSD processor
ORDERING INFORMATION
2
•
I C bus control
•
Cut-off brightness control
•
R/G/B sub contrast/cut-off control
•
Half tone
Device
Package
Operating Temperature
S1D2502B01-D0B0
32-DIP-600A
-20 °C — +75°C
FEATURES
VIDEO AMP PART
OSD PART
•
3-channel R/G/B video amplifier, 175MHz @f-3dB
•
Built in 1K-byte SRAM
•
I2C bus control items
— Contrast control: -38dB
— Sub contrast control for each channel: -12dB
— Brightness control
— OSD contrast control: -38dB
— Cut-off brightness control (AC coupling)
— Cut-off control for each channel (AC coupling)
— Switch registers for SBLK and video half tone and
CLP/BLK polarity selection and INT/EXT CLP selection
and generated CLP width control
•
448 ROM fonts (each font consists of 12 × 18
dots.)
•
Full screen memory architecture
•
Wide range PLL available (15kHz — 90kHz,
Reference 800 X 600)
•
Programmable vertical height of character
•
Programmable vertical and horizontal
positioning
•
Character color selection up to 16 different
colors
•
Built in ABL (automatic beam limitation)
•
Built in video input clamp, BRT clamp
•
•
Built in video half tone (3mode) function on OSD
pictures
Programmable background color (up to 16
colors)
•
Character blinking, bordering and shadowing
•
Capable of 8.0Vp-p output swing
•
Color blinking
•
Improvement of rise & fall time (2.2ns)
•
Character scrolling
•
Cut-off brightness control
•
Fade-in and fade-out
•
Built in blank gate with spot killer
•
Box drawing
•
Clamp pulse generator
•
Character sizing up to four times
•
OSD intensity
•
•
BLK, CLP polarity selection
72MHz pixel frequency from on-chip PLL
(Reference 800 X 600)
•
Clamp gate with anti OSD sagging
0
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
BLOCK DIAGRAM
9
VDD 31
ROM
(448 x 18 x 12)
Ctrl Data
Display Ctrl
V_Pulse
ROM Ctrl
4
H/V/CLK Ctrl
R/G/B OSD H/V/CLK Ctrl
FBLK
Intensity
Timing Controller Frame Ctrl
VREF
5
Latches
8
CONT_CAP
7
32
HFLB
1
VFLB
3
VCO_IN_P
30
SDA
29
SCL
2
I C bus
decoder D/A
RGB OSD
FBL
BLK
BLK
Int
INTE
HT DET.
CLP
ABL
VSSA
Control
Register
ROM Ctrl
Multi (3 mode)
Half Tone
OSD
PLL
H_Pulse
Display
Controller
9
Band
Gap.Ref
2
16
Frame Ctrl
Output Stage
VREF1
Data Receiver
CLK
VCC3 11
VDDA
RAM Data
12
Font Data
GND3
ROM
(480 x 16)
ROM
Address
Ctrl Font
VSS 28
6
16
Clamp
Pulse
Gen.
R cut off
V/I
27
RCT
G cut off
V/I
26
GCT
B cut off
V/I
25
BCT
10
CLP_IN
24
R OUT
22
VCC2
23
R CLP
19
GND2
20
G CLP
21
G OUT
17
B CLP
18
B OUT
HFLB
ABL
Video
Input
Clamp
RIN 12
Video
Half Tone
SW
CLP
GND1 15
R OSD
FBLK
OSD
Input
Cilp.
Sub
Cont.
Control
I2 C
OSD
Half Tone
SW
HT DET.
FBLK
Video
Contrast
Amp
Out
I2 C
OSD
Cont.
Control
I2 C
Sub
Cont.
Control
+
BLK
Birght
Control
I2C Cont. Cntl
I2C
I2 C
CLP
VCC1 13
GIN 14
G-CHANNEL
G OSD
CLP
HT DET.
I2 C
FBLK
BIN 16
CLP
BLK
B-CHANNEL
B OSD
CLP
HT DET.
FBLK
I2 C
CLP
BLK
Figure 1. Functional Block Diagram
1
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
PIN CONFIGURATION
VFLB
HFLB 32
2
VSSA
VDD 31
3
VCO_IN_P
SDA 30
4
VREF1
SCL 29
5
VREF
VSS 28
6
VDDA
RCT 27
7
CONT_CAP
GCT 26
8
ABL_IN
9
GND3
S1D2502B01
1
BCT 25
ROUT 24
10 CLP_IN
RCLP 23
11 VCC3
VCC2 22
12 RIN
GOUT 21
13 VCC1
GCLP 20
14 GIN
GND2 19
15 GND1
BOUT 18
16 BIN
BCLP 17
Figure 2. Pin Configuration
2
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 1. Pin Configuration
Pin No.
Symbol
I/O
Configuration
1
VFLB
I
Vertical flyback signal
2
VSSA
-
Ground (PLL part)
3
VCO_IN_P
I
This voltage is generated at the external loop filter and goes into the
input stage of the VCO.
4
VREF1
O
Charge pump output
5
VREF
O
PLL regulator filter
6
VDDA
-
+5V supply voltage for PLL part
7
CONT_CAP
-
Contrast control for AMP part
8
ABL
-
Auto beam limit.
9
GND3
-
Ground for video AMP part(for AMP control)
10
CLP_IN
-
Video clamp pulse input
11
VCC3
-
+12V supply voltage for video AMP part(for AMP control)
12
RIN
I
Video signal input (red)
13
VCC1
-
+12V supply voltage for video AMP(for main video signal process)
14
GIN
I
Video signal input (green)
15
GND1
-
Ground for video AMP part(for main video signal process)
16
BIN
I
Video signal input (blue)
17
BCLP
-
B output clamp cap
18
BOUT
O
Video signal output (blue)
19
GND2
-
Ground for video AMP part(for video output drive)
20
GCLP
-
G output clamp cap
21
GOUT
O
Video signal output (green)
22
VCC2
-
+12V supply voltage for video AMP part(for video output drive)
23
RCLP
-
R output clamp cap
24
ROUT
O
Video signal output (red)
25
BCT
-
B cut-off output
26
GCT
-
G cut-off output
27
RCT
-
R cut-off output
28
VSS
-
Ground for digital part
29
SCL
I
Serial clock (I2C)
30
SDA
I/O
Serial data (I2C)
31
VDD
-
+5V supply voltage for digital part
32
HFLB
I
Horizontal flyback signal
3
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
PIN DESCRIPTION
Table 2. Pin Description
Pin No
Pin Name
1
VFLB
Schematic
Description
FLB signal is in TTL level
VFLB
HFLB
32
HFLB
Multi polarity input
3
VCO_IN_P
PLL loop filter output
4
VPEF/
BandGap ref. output
5
VREF
7
Contrast cap
(CONT_CAP)
Contrast cap range
(0.1uF — 5uF)
4.0K
I2C Data
Vref
100µ A
8
ABL_IN
ABL input DC range
(1 — 4.5V)
VCC
100K
2K
Vref
Vref
250µA
4
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 2. Pin Description (Continued)
Pin No
Pin Name
10
CLP_IN
Schematic
Description
Multi polarity input
VCC
50K
Clamp gate pulse TTL level
input
10K
12
Red video input
(RIN)
Max input video signal is 0.7
Vpp
VCC
VCC
14
Green video input
(GIN)
16
Blue video input
(BIN)
Video_In
0.2K
12K
17
Blue (B clamp cap)
20
Green (G clamp cap)
Brightness controlling actives by
charging and discharging of the
external cap. (0.1µF)
(During clamp gate)
0.2K
CLP
23
Red (R clamp)
0.2K
Iclamp
5
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 2. Pin Description (Continued)
Pin No
Pin Name
18
Blue video output
(BOUT)
Schematic
Description
Video signal output
VCC
0.05K
21
Green video output
(GOUT)
0.5K
0.04K
24
Red video output
(ROUT)
27
Red cut-off control
(RCT)
26
Video_Out
Isink
Cut-off control output
0.2K
CTX
Green cut-off control
(GCT)
0-600uA 0-200uA 50uA 100uA
25
Blue cut-off control
(BCT)
29
SCL
Serial clock input port of I2C bus
SCL
30
Serial data input port of I 2C bus
SDA
SCL
ACK
6
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
ABSOLUTE MAXIMUM RATINGS (see 1)
(Ta = 25 °C)
Table 3. Absolute Maximum Ratings
No
1
Item
Value
Symbol
Maximum supply voltage
Unit
Min
Typ
Max
VCC
-
-
13.2
VDD
-
-
6.5
-
75
°C
150
°C
2
Operating temperature (see 2)
Topr
-20
3
Storage temperature
Tstg
-65
4
Operating supply voltage
VCCop
11.4
12.0
12.6
VDDop
4.75
5.00
5.25
PD
-
-
5
Power dissipation
V
V (see 3)
W
THERMAL & ESD PARAMETER
Table 4. Thermal & ESD Parameter
Value
No
Item
Symbol
Min
Typ
Max
Unit
1
Thermal resistance
(junction-ambient)
θja
-
48
-
°C/W
2
Junction temperature
Tj
-
150
-
°C
3
Human body model
(C = 100p, R = 1.5k)
HBM
2
-
-
KV
4
Machine model
(C = 200p, R = 0)
MM
300
-
-
V
5
Charge device model
CDM
800
-
-
V
7
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
ELECTRICAL CHARACTERISTICS
DC ELECTRICAL CHARACTERISTICS
(Tamb = 25 °C, VCC = 12V, V DD = VDDA = 5V, ABL input voltage = 5V, HFLB input signal = S3, load resistors =
470Ω, except OSD part current 35mA, unless otherwise stated)
Table 5. DC Electrical Characteristics
Value
Parameter
Supply current
Symbol
Conditions
ICC (see 4)
Unit
Min
Typ
Max
100
125
130
mA
Minimum supply current
ICC min
VCC = 11.4V
95
110
120
mA
Maximum supply current
ICC max
VCC = 12.6V
105
130
140
mA
ABS supply current
ICC abs
VCC = 13.2V
-
-
175
mA
Video input bias voltage
V bias
1.8
2.1
2.4
V
V blackpor
1.20
1.50
1.80
V
∆ V blackpor
∆ 10
-
-
%
2.2
2.7
3.2
V
∆ 10
-
-
%
-
0.2
0.5
V
∆ 10
-
-
%
Video black level voltage (POR)
Black level voltage channel difference (POR)
(see 5)
Video black level voltage (FFH)
V blackff
Black level voltage channel difference (FFH)
∆ V blackff
Video black level voltage (00H)
V black00
Black level voltage channel difference (00H)
04 = FFH (see 13)
04 = 00H
∆ V black00
Spot killer voltage
Vspot
VCC = Var.
9.20
10.4
11.2
V
Cut-off current (FFH)
ICTff
Pin25, 26, 27 = 12V
09 — 0B: FFH
0C: 00H
500
625
750
µA
Cut-off current (00H)
ICT00
Pin25, 26, 27 = 12V
09 — 0C: 00H
-
2.0
5.0
µA
Cut-off brightness current (FFH)
ICTBRTff
Pin25, 26, 27 = 12V
09 — 0B: 00H
0C: FFH
100
180
260
µA
Cut-off brightness current (80H)
ICTBRT80
Pin25, 26, 27 = 12V
09 — 0B: 00H
0C: 80H
50
90
130
µA
ICS1
Pin25, 26, 27 = 12V
09 — 0C: 00H
0E: 11H
25
50
75
µA
Cut-off offset current 1
8
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 5. DC Electrical Characteristics (Continued)
Value
Parameter
Symbol
Conditions
Cut-off offset current 2
ICS2
Pin25, 26, 27 = 12V
09 — 0C: 00H
0E: 12H
Soft BLK output voltage
Vsblk
0D: 80H
0E: 14H
Clamp cap voltage (POR)
Vcap
Unit
Min
Typ
Max
50
100
130
µA
-
0.2
0.5
V
6.0
7.0
8.0
V
Total external cut-off current range
Red
cut-off
Creen
cut-off
Blue
cut-off
Cut-Off Brightness
600uA
200uA
CS2
Cut-Off Offset
Switch
100uA
CS1
150uA
50uA
9
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
AC ELECTRICAL CHARACTERISTICS
(Tamb = 25 °C, VCC = 12V, V DD = VDDA = 5V, ABL input voltage = 5V, HFLB input signal = S3, load resistors =
470Ω, Vin = 0.7Vpp manually adjust video output pins 18, 21 and 24 to 4V DC for the AC test (see 11) unless
otherwise stated (see 12))
Table 6. AC Electrical Characteristics
Value
Parameter
Contrast max. output voltage
Symbol
Vcff
Contrast max. output channel difference
∆ Vcff
Contrast center output voltage
Vc80
Conditions
03, 05, 06, 07 = FFH
04, 08 — 0C = 80H
RGB input = S1
Unit
Min
Typ
Max
5.0
5.7
6.4
Vpp
∆ 10
-
-
%
2.5
2.85
3.2
Vpp
∆ Vc80
03, 04, 08 ~ 0C = 80H
05, 06, 07 = FFH
RGB input = S1
∆ 10
-
-
%
Contrast max. - Center attenuation
C
C = 20log (Vc80/Vcff)
-8
-6
-4
dB
Sub contrast center output voltage
Vd80
2.3
2.6
2.9
Vpp
Sub contrast center output channel
difference
∆ Vd80
03 = FFH
04 — 0C = 80H
RGB input = S1
∆ 10
-
-
%
Contrast center output channel difference
Sub contrast min. output voltage
Sub contrast min. output channel difference
Sub contrast max. - min. attenuation
ABL control range
Vd00
∆ Vd00
D
ABL
03 = FFH, 05—07: 00H
04, 08 — 0C = 80H
RGB input = S1
1.3
1.6
1.9
Vpp
∆ 10
-
-
%
D = 20log (Vd00/Vcff)
-14
-12
-10
dB
(see 15)
-12
-10
-8
dB
03, 05 ~ 07: FFH
04, 08 ~ 0C: 80H
RGB input = S2
-
2.2
2.8
ns
-
2.2
2.8
ns
POR
HFLB: S4
-
6.0
12.0
ns
-
8.0
15.0
ns
R/G/B video rising time (see 7)
tr (video)
R/G/B video falling time (see 7)
tf (video)
R/G/B blank output rising time (see 7)
tr (blank)
R/G/B blank output falling time (see 7)
tf (blank)
R/G/B video band width (see 7, 8)
f (-3dB)
(see 16)
175
-
-
MHz
Video AMP 50MHz cross talk
CT_50M
(see 17)
-
-25
-20
dB
(see 18)
-
-15
-10
dB
-1
-
1
dB
-1
-
1
dB
(see7, 9)
Video AMP 130MHz cross talk
CT_130M
(see7, 9)
Absolute gain match
Gain change between amplifier
10
Avmatch (see 6)
Avtrack
(see 7)
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
OSD ELECTRICAL CHARCTERISTICS
(Tamb = 25 °C, VCC = 12V, V DD = VDDA = 5V, HFLB input voltage = S3, load rosistors = 470Ω, V-AMP test
registor’s FBLK, OSD input conditions unless otherwise stated)
Table 7. OSD Electrical Chaacteristics
Value
Parameter
Symbol
OSD contrast max. output voltage
Vocff
OSD contrast max. output channel
difference
∆ Vocff
OSD contrast center output voltage
Voc80
OSD contrast center output channel
difference
∆ Voc80
R/G/B OSD rising time
tr (OSD)
R/G/B OSD falling time
tf (OSD)
HT video level
HTvideo
HT video output channel difference
HT OSD level
HT OSD output channel difference
∆ HTvideo
HTosd
∆ HTosd
Conditions
08 = FFH
OSD RGB output conditions
08 = 80H
OSD RGB output conditions
08: FFH
ABL = 6V
RGB input = S1
03, 05 — 08: FFH
0D: 01H
OSD black conditions input
HTvideo = 20log(Vhtvideo/Vcff)
ABL = 6V
05 — 08: FFH
0D: 0FH
OSD white condition input
HTosd = 20log (Vhtosd/Vocff)
Unit
Min
Typ
Max
5.4
6.4
7.4
Vpp
∆ 10
-
-
%
2.7
3.2
3.7
Vpp
∆ 10
-
-
%
-
4.0
5.0
ns
-
4.0
5.0
ns
-6.0
-4.5
-3.0
dB
∆ 15
-
-
%
-7.0
-5.5
-4.0
dB
∆ 15
-
-
%
11
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
OPERATION TIMINGS
Table 8. Operation Timings
Parameter
Symbol
Min
Typ
Max
Unit
Horizontal flyback signal frequency
fHFLB
-
-
120
kHz
Vertical flyback signal frequency
fVFLB
-
-
200
Hz
fSCL
-
-
300
kHz
Hold time for start condition
ths
500
-
-
ns
Set up time for stop condition
tsus
500
-
-
ns
Low duration of clock
tlow
400
-
-
ns
High duration of clock
thigh
400
-
-
ns
Hold time for data
thd
0
-
-
ns
Set up time for data
tsud
500
-
-
ns
Time between 2 access
tss
500
-
-
ns
Fall time of SDA
tfSDA
-
-
20
ns
Rise time of both SCL and SDA
trSDA
-
-
-
ns
Input Signal HFLB, VFLB
2
I C Interface SDA, SCL (Refer to Figure 3)
SCL clock frequency
tss
thd
SDA
ths
tsud
SCL
tsus
thigh
tlow
Figure 3. I 2C Bus Timing Diagram
12
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
OSD PART ELECTRICAL CHARACTERISTICS
OSD PART DC ELECTRICAL CHARACTERISTICS
(Ta = 25 °C, VDDA = VDD = 5V)
Table 9. OSD Part DC Electrical Characteristics
Parameter
Symbol
Min
Typ
Max
Unit
Supply voltage
VDD
4.75
5.00
5.25
V
Supply current
(no load on any output)
IDD
-
-
25
mA
Input voltage
VIH
0.8VDD
-
-
V
VIL
-
-
VSS + 0.4
V
VOH
0.8VDD
-
-
V
VOL
-
-
VSS + 0.4
V
IIL
-10
-
10
µA
Output voltage
(lout = ±1mA)
Input leakage current
VCO input voltage
VVCO
2.5
V
13
S1D2502B01
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
NOTES:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
14
Absolute maximum rating indicates the limit beyond which damage to the device may occur.
Operating ratings indicate conditions for which the device is functional but do not guarantee specific performance limits.
For guaranteed specifications and test conditions, see the electrical characteristics. The guaranteed specifications apply
only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under
the listed test conditions.
VCC supply pins 11, 13, and 22 must be externally wired together to prevent internal damage during VCC power on/off
cycles.
The supply current specified is the quiescent current for VCC1 /VCC2 and VCC 3 with RL = ∞, The supply current
for VCC2 (pin 22) also depends on the output load.
Output voltage is dependent on load resistor. Test circuit uses RL = 470Ω
Measure gain difference between any two amplifiers Vin = 700mVpp.
When measuring video amplifier bandwidth or pulse rise and fall times, a double sided full ground plane printed circuit
board without socket is recommended. Video amplifier 50MHz cross talk test also requires this printed circuit board. The
reason for a double sided full ground plane PCB is that large measurement variations occur in single sided PCBs.
Adjust input frequency from 10MHz (AV max reference level) to the -3dB frequency (f -3dB).
Measure output levels of the other two undriven amplifiers relative to the driven amplifier to determine channel separation.
Terminate the undriven amplifier inputs to simulate generator loading. Repeat test at fin = 50MHz for cross talk 50MHz.
A minimum pulse width of 200 ns is guaranteed for a horizontal line of 15kHz. This limit is guaranteed by design. if a lower
line rate is used a longer clamp pulse may be required.
During the AC test the 4V DC level is the center voltage of the AC output signal. For example. If the output is 4Vpp the
signal will swing between 2V DC and 6V DC.
These parameters are not tested on each product which is controlled by an internal qualification procedure.
The conditions block’s 03, 04, 05... etc. signify sub address’0F03, 0F04, 0F05... etc.
Sub address 0F03, 0F05 ~ 0F07: FFH
0F04, 0F08 ~ 0F0C: 80H
RGB input = S1,
When the ABL input voltage is 0V, the R/G/B’s output voltage is VR/VG/VB and uses the formula ABLR = 20log (VR/V cffR)
OSD TST mode = High, CLP operation off,
RGB input = S5 (frequency sweep),
RGB input clamp cap = 2.1V DC,
RGB clamp cap (pin 23/20/17) = Vcap voltage (7.0V),
S5’s frequency 1MHz → 130MHz sweep, -3dB point = 20log (V130MHz/V1MHz)
03, 05 ~ 07: FFH
04, 08 ~ 0C: 80H
0F: 80H
OSD TST mode = High, CLP operation off,
RGB input clamp cap = 2.1V DC,
RGB clamp cap (pin 23/20/17) = Vcap voltage (7.0V),
03, 05 ~ 07: FFH
04, 08 ~ 0C: 80H
0F: 80H
R input = S5 (50MHz)
CT_50M = 20log (VoutG/VoutR) or 20log (VoutB/VoutR)
OSD TST mode = High, CLP operation off,
RGB input clamp cap = 2.1V DC,
RGB clamp cap (pin 23/20/17) = Vcap voltage (7.0V),
03, 05 ~ 07: FFH
04, 08 ~ 0C: 80H
0F: 80H
R input = S5 (130MHz)
CT_150M = 20log (VoutG/VoutR) or 20log (V outB/VoutR)
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
TEST SIGNAL FORMAT
Table 10. Test Signal Format
Signal
Name
Input Signal Formal
Signal Description
S1
Video gain measurement
Video
[V]
Video = 1MHz/0.7Vpp
Sync = 50kHz
Sync
4uS
[t]
S2
Video Tr/Tf measurement
[V]
0.7
Vpp
f = 200kHz
f = 200kHz
V = 0.7Vpp
Duty = 50%
[t]
Duty = 50%
S3
HFLB (posi & nega.) input
[V]
f = 50kHz
t = 2uS
V = 0V/5V
t = 2uS
[t]
f = 50kHz
S4
OSD level measurement
[V]
f = 200kHz
5V
Blank Tr/Tf measurement
0V
f = 50kHz
V = 0V/5V
[t]
Duty = 50%
S5
Crosstalk test
[V]
Bandwidth measurement
Vi
Vref
1MHz/10MHz/50MHz/
130MHz
[t]
Vref = input clamp voltage
Vi = 0.7Vpp
•
S1, S2 signal’s low level must be synchronized with the S3 signal’s sync. term.
•
The input signal level uses the IC pin as reference.
15
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
TEST CIRCUIT
VDD = 5.0V
33
33
BNC3
BNC1
1
VFLB
HFLB
32
2
VSSA
VDD
31
3
VCO_IN_P
SDA
30
100u
33
1M
BNC2
5.6K
562
1
33
2 SW1
27K
30M
4.7K
BNC4
33
4
VREF1
SCL
5
VREF
VSS
28
6
VDDA
RCT
27
7
CONT_CAP
GCT
26
8
ABL_IN
BCT
25
9
GND3
ROUT
24
10
CLP_IN
RCLP
23
11
VCC3
VCC2
22
12
RIN
GOUT
21
13
VCC1
GCLP
20
14
GIN
GND2
19
15
GND1
BOUT
18
16
BIN
BCLP
17
4.7K
29
4.7u
BNC5
2K
103
1u
100u
2K
2K
100
ABL
S1D2502B01
KB2502
1u
470
33
0.1u
BNC6
100u
75
0.1u
470
100u
BNC7
75
0.1u
0.1u
470
BNC8
75
0.1u
0.1u
BNC9
VCC = 12.0V
Magnetic Core
Figure 4. Test Circuit
16
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
FUNCTIONAL DESCRIPTIONS
DATA TRANSMISSION
The interface between S1D2502B01 and MCU follows the I2C protocol. After the starting pulse, the transmission
takes place in the following order: Slave address with R/W bit, 2-byte register address, 2-byte data, and stop
condition. an acknowledge signal is received for each byte, excluding only the start/stop condition. The 2-byte
register address is composed of an 8-bit row address, and an 8-bit column address. The order of transmission for
a 2-byte register address is 'Row address → Column address'. The 2 bytes of data is because S1D2502B01 has a
16-bit base register configuration. S1D2502B01's slave address is BAh. It is BBh in read mode, and BAh in write
mode.
•
Address Bit Pattern for Display Registers Data
(a) row address bit pattern
R3 - R0: Valid data for row address
A15
A14
A13
A12
A11
A10
A9
A8
X
X
X
X
R3
R2
R1
R0
(b) Column address bit pattern
C4 - C0: Valid data for column address
A7
A6
A5
A4
A3
A2
A1
A0
X
X
X
C4
C3
C2
C1
C0
X:Don't care bit
•
Data Transmission Format
Start → Slave address → ACK → Row address → ACK → Column address → ACK
Data byte N → ACK → Data byte N+1 → ACK → Stop
Figure 5. Data Transmission Format at Writing Operation
Start → Slave address → ACK → Row address → ACK → Column address → ACK → Stop
Start → Slave address → ACK → Data byte N → ACK → Data byte N+1 → ACK → Stop
Figure 6. Data Transmission Format at Reading Operation
17
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
•
SDA / SCL Signal At Communication
SCL
R/W
SDA
START
A15 A14 A13 A12 A11 A10 A9
IIC SLAVE ADDRESS
ACK
A8
A7
MSB ADDRESS
A6
A5
ACK
A4
A3
A2
A1
A0
LSB ADDRESS
ACK
SCL
...
SDA
D7
D6
D5 D4 D3 D2 D1 D0
DATA BYTE N(MSB DATA)
ACK
D7
D6
D5 D4 D3 D2 D1 D0
DATA BYTE N(LSB DATA)
ACK
D7
D6
D5 D4 D3 D2 D1 D0
DATA BYTE N(MSB DATA)
ACK
...
STOP
Figure 7. SDA line and SCL line (Write Operation)
SCL
R/W
SDA
START
IIC SLAVE ADDRESS
START
IIC SLAVE ADDRESS
A15 A14 A13 A12 A11 A10 A9
ACK
A8
MSB ADDRESS
A7
A6
A5
ACK
A4
A3
A2
A1
A0
LSB ADDRESS
ACK
STOP
SCL
SDA
R/W
D15 D14 D13 D12 D11 D10 D9
ACK
DATA BYTE N(MSB)
D7
D8
D6
ACK
Figure 8. SDA line and SCL line (Read Operation)
18
D5
D4
D3
D2
D1
DATA BYTE N(LSB)
D0
ACK STOP
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
MEMORY MAP
00 01 02
27 28 29
30
Row 00
Row 01
Character & Attribute Registers
(30 x15 Character Display)
Row 12
Row 13
Row 14
Row 15
00 01 02 03 04 05 06 07 08 0910 11 12 13 14 15 16
Row Attribute
Registers
31
V-AMP Test Registers
Frame Control V-AMP Control Registers
Registers
Test Registers
Figure 9. Memory Map of Display Registers
The display RAM's address of the row and column number are assigned in order. The display RAM is composed of
4 register groups (character & attribute register, row attribute register, frame control register, and V-AMP control
register).
The display area in the monitor screen is 30 column × 15 row, so the related character & attribute registers are also
30 column × 15 row. Each register has a character address and characteristics corresponding to the display
location on the screen, and one register is composed of 16 bits. The lower 9 bits select the font from the 448 ROM
fonts, and the upper 7 bits give font characteristics to the selected font.
The row attribute register takes up the display RAM's 31st column. It provides raster color, raster color intensity,
character color intensity, horizontal & vertical character size, box, border, and shadow features in units of row.
The frame control registers are in the 16th row. It controls OSD's display location, character height, scroll, and
fade-in/out in units of frame.
The V-AMP control registers are also located in the 16th row.
19
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
REGISTER DESCRIPTION
♦ Character & Attribute Register: Row00 ~ 14, Column00 ~ 29
F
E
D
C
B
A
9
8
7
6
5
BINV BOX1 BOX0
B
G
R
Blink/Fint
C8
C7
Character Attribute
C6
6
RR
Raster Color
♦ Frame Control Register 0: Row15, Column00
F
E
D
C
B
A
9
8
Fde FdeT VPOL HPOL
♦ Frame Control Register 1: Row15, Column01
F
E
D
C
B
A
9
8
CP0
Fpll
HF2
HF1
HF0
dot1
dot0
HP5
HP4
HP3
2
1
0
C2
C1
C0
5
4
3
Intensity
2
1
0
HZ0
VZ1
VZ0
Character Size
7
-
6
5
4
3
2
1
0
Erase
EN
Scrl
ScrT
Bli1
Bli0
BliT
7
-
6
5
FBLK CH5
4
3
2
1
0
CH4
CH3
CH2
CH1
CH0
Character Height Control
♦ Frame Control Register 2: Row15, Column02
F
E
D
C
B
A
9
8
HP6
3
C3
RINT CINT HZ2
PLL Control
HP7
4
C4
Character Code (448 fonts)
♦ Row Attribute Register: Row00 ~ 14, Column30
F
E
D
C
B
A
9
8
7
- BREN INTE CBil BOXE BORD SHA RB RG
CP1
C5
HP2
HP1
HP0
7
6
5
4
3
2
1
0
VP7
VP6
VP5
VP4
VP3
VP2
VP1
VP0
Horizontal Start Position
Vertical Start Position
♦ V-AMP Control Register: Row15, Column03 ~ 15
Column03
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
-VC7 VC6 VC5 VC4 VC3 VC2 VC1 VC0
Column04
F
E
Column05
F
E
-
Contrast Control
D
-
C
-
B
--
A
-
9
-
8
-
7
6
5
4
3
2
1
0
BRT7 BRT6 BRT5 BRT4 BRT3 BRT2 BRT1 BRT0
Brightness Control
D
-
C
-
B
--
A
-
9
-
8
-
7
6
5
4
3
2
1
0
RSB7 RSB6 RSB5 RSB4 RSB3 RSB2 RSB1 RSB0
R SUB Contrast Control
Column06
F
E
-
D
-
C
-
B
--
A
-
9
-
8
-
7
6
5
4
3
2
G SUB Contrast Control
20
1
0
GSB7 GSB6 GSB5 GSB4 GSB3 GSB2 GSB1 GSB0
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
♦ V-AMP Control Register: Row15, Column03 ~ 15
Column07
F
E
Column08
F
E
Column09
F
E
-
D
-
C
-
B
-
A
-
9
-
8
-
7
6
5
4
3
2
1
0
BSB7 BSB6 BSB5 BSB4 BSB3 BSB2 BSB1 BSB0
B SUB Control
D
-
C
-
B
-
A
-
9
-
8
-
7
6
5
4
3
2
1
0
OSD7 OSD6 OSD5 OSD4 OSD3 OSD2 OSD1 OSD0
OSD Contrast Control
D
-
C
-
B
-
A
-
9
-
8
-
7
6
5
4
3
2
1
0
RWB7 RWB6 RWB5 RWB4 RWB3 RWB2 RWB1 RWB0
R Cut-off Control
Column10
F
E
-
D
-
C
-
B
-
A
-
9
-
8
-
7
6
5
4
3
2
1
0
GWB7GWB6GWB5GWB4GWB3GWB2GWB1GWB0
G Cut-off Control
Column11
F
E
-
D
-
C
-
B
-
A
-
9
-
8
-
7
6
5
4
3
2
1
0
BWB7 BWB6 BWB5 BWB4 BWB3 BWB2 BWB1 BWB0
B Cut-off Control
Column12
F
E
-
D
-
C
-
B
-
A
-
9
-
8
-
7
6
5
4
3
2
1
0
CUT7 CUT6 CUT5 CUT4 CUT3 CUT2 CUT1 CUT
Cut-off Brightness Control
Column13
F
E
-
D
-
C
-
B
-
A
-
9
-
8
-
7
6
5
4
3
2
1
0
SB
HS6
HS5
HS4
HS3
HS2
HS1
HT
Half Tone & Soft Blank Control
Column14
F
E
-
D
-
C
-
B
-
A
-
9
-
8
-
7
6
5
4
3
CLPS CLPP BLKP BPW2 BPW1
2
1
0
-
CS2
CS1
Clamp, Polarity & Offset Control
Column15
F
E
-
D
-
C
-
B
-
A
-
9
-
8
-
7
-
6
-
5
-
4
-
3
2
1
0
TST
HS9
HS8
HS7
Half Tone Control
’ - ’; Don’t care bit
Figure 10. Register Description
21
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 11. Register Description
Registers
Bits
Description
Character &
Attribute Registers
(Row 00 — 14,
Column 00 — 29)
C8 — C0
(Bit 8 — 0)
Character code address
This is the address of 448 ROM fonts.
Blink/FINT
(Bit 9)
Character blinking/font intensity
If row attribute register's INTE bit is set to '1', this bit carries out the font
intensity feature, and if not, the character blinking feature instead. In other
words, to carry out character blinking, set the INTE bit to '0'. Select frame
control register-0's BliT bit as blinking time, and select Bli1, Bli0 Bit as
blinking duty. When giving intensity in units of font, refer to the table below.
Blink/FINT
INTE
RINT
CINT
Function
0
0
-
-
Normal
0
1
-
-
Normal
1
0
-
-
Blink
1
1
0
1
Character intensity
1
1
1
0
Raster intensity
1
1
1
1
Character & raster intensity
B, G, R
(Bit C — A)
Character color
The character color is chosen from 16 colors using these 3 bits and the row
attribute register's CINT bit.
BOX1, BOX0
(Bit E, D)
Character box drawing
You can make 4 box drawing modes using these 2 bits in combination. The
box drawings possible with font 'A' are shown below.
BOX0
BOX1
o
1
0
BOX OFF
A
1
A
A
Refer to row attribute register's 'BOXE' bit.
BINV
(Bit F)
22
Box inversion
The white box turns black and black box turns white in the box drawing
using BOX1, BOX0.
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 11. Register Description (Continued)
Registers
Row Attribute
Registers
(Row00— 14,
Column30)
Bits
VZ1, VZ0
(Bit 1, 0)
Description
Vertical character size control
VZ1
VZ0
Vertical Character Size
0
0
1X (1 time)
0
1
2X (2 times)
1
0
3X (3 times)
1
1
4X (4 times)
As shown above, the vertical character size is decided by using these two
bits in combination.
HZ1, HZ0
(Bit 3, 2)
Horizontal character size control
HZ1
HZ0
Horizontal Character Size
0
0
1X (1 time)
0
1
2X (2 times)
1
0
3X (3 times)
1
1
4X (4 times)
As shown above, the horizontal character size is decided by using these
two bits in combination. However, unlike VZ, the surrounding area (row) is
taken over in the amount of the HZ increase, so you must keep that in mind
when changing font size. Refer to Character Size.
CINT
(Bit 4)
Character color intensity
When this bit is set to '1', the color intensity of the character on the same
row becomes high. Refer to BLINK/FINT, INTE, RINT, and CINT's
combination chart in the previous page. (Even if you change this bit, you
can't check the intensity feature on the demo board. This is because the
OSD IC's output INT is applied as the video Pre Amp's input, and the demo
board doesn't apply the OSD IC's INT output to the Pre Amp.)
RINT
(Bit 5)
Raster color intensity
When this bit is set to '1', the color intensity of the raster on the same row
becomes high. Refer to BLINK/FINT, INTE, RINT, and CINT's combination
chart in the previous page. (Like CINT given above, you can't check RINT's
feature on the demo board.)
23
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 11. Register Description (Continued)
Registers
Row Attribute
Registers
(Row00 — 14,
Column30)
Bits
Description
RB, RG, RR
(Bit 8 — 6)
Raster color is determined by these bits
The raster color is chosen from out of 16 colors using these 3 bits and the
row attribute register's 'RINT' bit. If 'BOXE' Bit is not '1', the setting of these
three bits have no meaning. Refer to 'BOXE' bit shown below.
SHA
Character shadowing
Character shadowing feature is carried out if you set this bit to '1'.
BORD
Character bordering
Character bordering feature is carried out if you set this bit to '1'.
BOXE
(Bit B)
BOX enable
If you set this bit to '1', it uses the character & attribute register's 'BINV',
'BOX1', and 'BOX0' bits to carry out box drawing, and if you set it to '0', the
character & attribute register's bits F~D (BINV, BOX1, BOX0) act as each
raster color's B, G, and R. This has higher priority than selection by setting
RB, RG, and RR bits. In other words, if the BOXE bit is set to '0', the
character & attribute register's BINV, BOX1, and BOX0 each do the
function of RB, RG, and RR to decide the raster color, and the original row
attribute register's RB, RG, and RR don't do anything.
CBli
(Bit C)
Color blink enable
If this bit is '1', the color blinking effect is applied. Color blinking is instead
of normal blinking, 8 colors appear in order in the font's character part. Its
time and duty is controlled by 'BliT', 'Bli1', and 'Bli0', like in character
blinking.
INTE
(Bit D)
Intensity enable
Refer to the table on the combination of BLINK/FINT, INTE, RINT, and
CINT bits in the explanation of the character & attribute register's BLINK/
FINT bit.
BREN
(Bit E)
Back raster enable
If the BREN bit is '1' and the raster color is black, the raster is transparent.
That is, the video back raster is shown. If not, the OSD raster covers the
video's back raster. Refer to other color effect.
Bit F
24
Reserved
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 11. Register Description (Continued)
Registers
Frame Control
Registers — 0
(Row 15,
Column 00)
Bits
BliT
(Bit 0)
Bli1, Bli0
(Bit 2 — 1)
Description
Blink time control
If this bit is '1', blink time is 0.5sec, and if not, 1sec.
Blinking duty control
As the font blinks, there is a time when it is visible and invisible on screen.
Blinking duty is the ratio of the invisible time to the visible time, and is
decided by the combination of these two bits. In other words, blinking duty
is the length of time the font is shown on screen.
Bli1
Bli0
Blinking Duty
0
0
Blink Off
0
1
Duty 25%
1
0
Duty 50%
1
1
Duty 75%
ScrT
(Bit 3)
Scroll time control
If this bit is '1', scroll time is 0.5sec, and if not, 1sec.
Scrl
(Bit 4)
Scroll enable
Scrolling effect is controlled by this bit. If this bit is 1
‘ ,’ scrolling effect is
enabled. You must remember that scrolling can be turned on/off only when
OSD is enabled/disabled.
EN
(Bit 5)
OSD enable
OSD is enabled when this bit is '1'. In other words, if this bit isn't '1'OSD is
not output inspite of writing control data. We recommend that you enable
the OSD after setting the control registers (such as the character & attribute
register) because of video and OSD output timing.
Erase
(Bit 6)
RAM erasing
If this bit is '1', the RAM data (character & attribute registers and row
attribute registers) is erased. The time spent in carrying out this operation is
called erasing time, which can be calculated as follows.
Erasing time = RAM clock × 480 (RAM cell no.)
RAM clock = 12 dot clock
Dot clock = 1/(dot frequency)
Dot frequency = Horizontal frequency × resolution (mode)
Therefore, the maximum erasing time value is:
(Erasing Time)MAX = (12 × 480) / (15k × 320) = 1.2ms
25
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 11. Register Description (Continued)
Registers
Frame Control
Registers — 0
(Row 15,
Column 00)
Bits
Description
HPOL
(Bit B)
Polarity of horizontal fly back signal
If this bit is '1', HFLB's polarity is positive, and if '0', it is negative. In other
words, this bit is set to '1' if active high, and '0' if active low.
VPOL
(Bit C)
Polarity of vertical fly back signal
If this bit is '1', VFLB's polarity is positive, and if '0', it is negative. In other
words, this bit is set to '1' if active high, and '0' if active low.
FdeT
(Bit D)
Fade-in and fade-out time control
If this bit is '1', fade-in/fade-out time is 0.5sec. If not, it is 1sec.
Fde
(Bit E)
Fade-in and fade-out enable
This feature is enabled when this bit is '1'. The effect where the display
goes from the center to the outside, or from the outside to the center in
units of font, is called fade-in/fade-out. Refer to fade-in/fade-out. You must
remember that fade-in/fade-out, like scrolling on/off, only occurs when OSD
enabled/disabled.
Bit F
Reserved.
The purpose of bits 'HPOL', and 'VPOL' is to provide flexibility when using the S1D2502B01 IC. No matter which
polarity you choose for the input signal, the IC will handle them identically, so you can select active high or active
low according to your convenience.
26
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Tabel 4. Register Description (Continued)
Registers
Frame Control
Registers — 1
(Row 15,
Column 01)
Bits
Description
CH5 — CH0 Character height control
(bit 5 — 0) While the purpose of VZ[1:0] (vertical character height) is to control the
absolute size of the character, the purpose of CH[5:0] (Character Height) is
to output OSD of a uniform size even if the resolution changes. If you adjust
the value in the range of CH = 18 — CH = 63, each line's repeating number
is decided (standard height CH = 18 is the reference value), by which the
line is repeated. For more information on repeating number selection, refer
to character height.
FBLK
(bit 6)
dot1, dot0
(bit 9, 8)
Selection of the FBLK output pin's configuration
Unlike pin description's FBLK, if this bit is '0', the FBLK pin output is high
while the character and raster are being displayed and the character and
raster are output as they are. If this bit is '1', the FBLK pin output becomes
high only when character is being displayed, so only the character is
output. Refer to 'Figure 11. Character/raster signal part.
Resolution control (dots/line)
Dot1
Dot0
No. of Dots
0
0
320 dots/line
0
1
480 dots/line
1
0
640 dots/line
1
1
800 dots/line
As shown above, the number of dots per horizontal line is decided by a
combination of these two bits.
HF2— HF0
(bit C — A)
FPLL
(bit D)
Horizontal frequency
PLL's horizontal frequency is decided by the combination of these 3 bits.
This is related to the selection of DOT[1:0], so you can't numerically
express the frequency range with only the HF[2:0] selection. For more
information, please refer to HF Bits Selection.
Full range PLL
If this bit is '1', the OSD_PLL block's VCO operates at full range (4.8MHz 96MHz). If it is 0’ ', it operates within the region decided by the HF bit [C:A]
explained above. if you can’t optimize OSD screen decided by the HF bit in
the high region, you may set the FPLL bit to 1‘ .’
27
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Tabel 4. Register Description (Continued)
Registers
Frame Control
Registers — 1
(Row 15,
Column 01)
Bits
Description
CP1, CP0
Charge pump output current control
This is the PLL block's internal phase detector output status, converted into
current. Refer to PLL control.
CP1
CP0
Charge Pump Current
0
0
0.50 mA
0
1
0.75 mA
1
0
1.00 mA
1
1
1.25 mA
The output is decided by the combination of these two bits.
Character
FBLK bit setting is explained at the figure below.
Blue
Red
Raster
Raster
Blue
Bordering
Red
Character
Green
Figure 11. Character/Raster Signal Part
28
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Tabel 4. Register Description (Continued)
Registers
Frame Control
Registers — 2
(Row 15,
Column 02)
V-AMP Control
Registers — 0
(Row 15,
Column 03)
Bits
Description
VP7 — VP0
Vertical start position control ( = VP[7:0] × 4)
Signifies top margin height from the V-Sync reference edge.
HP7 — HP0
Horizontal start position control ( = HP[7:0] × 6)
Signifies delay of the horizontal display from the H-Sync reference edge
to the character's 1st pixel location.
VC7 — VC0
(bit7 — 0)
The contrast adjustment is made by contrdling simultaneously the gain
of three internal variable gain amplifiers.
The contrast adjustment allows to cover a typical range of 38dB.
V-AMP Control
Registers — 1
(Row 15,
Column 04)
BRT7 — BRT0 The brightness adjustment controls to add the same black level
(pedestal) to the 3-channel R/G/B signals after contrast amplifier.
(bit7 — 0)
V-AMP Control
Registers — 2
(Row 15,
Column 05)
RSB7 — RSB0 R channel SUB contrast control.
(bit7 — 0)
The SUB contrast adjustment is used to adjust the white balance, and
the gain of each channel is controlled.
The SUB contrast adjustment allows you to cover a typical tange of
12dB.
V-AMP Control
Registers - 3
(Row 15,
Column 06)
GSB7 — GSB0 G channel SUB contrast control.
(bit7 — 0)
The SUB contrast adjustment is used to adjust the white balance, and
the gain of each channel is controlled.
The SUB contrast adjustment allows you to cover a typical tange of
12dB.
V-AMP Control
Registers - 4
(Row 15,
Column 07)
BSB7 — BSB0 B channel SUB contrast control.
(bit7 — 0)
The SUB contrast adjustment is used to adjust the white balance, and
the gain of each channel is controlled.
The SUB contrast adjustment allows you to cover a typical tange of
12dB.
V-AMP Control
Registers - 5
(Row 15,
Column 08)
OSD7 — OSD0 The OSD contrast adjustment is made by contrdling simultaneously the
gain of three internal variable gain amplifiers.
(bit7 — 0)
The OSD contrast adjustment allows to cover a typical range of 38dB.
V-AMP Control
Registers - 6
(Row 15,
Column 09)
RWB7 — RWB0 R channel cut-off control.
(bit7 — 0)
The cut-off adjustment is used to adjust the raster white balance.
V-AMP Control
Registers - 7
(Row 15,
Column 10)
GWB7 — GWB0 G channel cut-off control.
(bit7 — 0)
The cut-off adjustment is used to adjust the raster white balance.
29
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Tabel 4. Register Description (Continued)
Registers
Bits
Description
V-AMP Control
Registers - 8
(Row 15,
Column 11)
BWB7 — BWB0 B channel cut-off control.
(bit7 — 0)
The cut-off adjustment B used to adjust the raster white balance.
V-AMP Control
Registers - 9
(Row 15,
Column 12)
CUT7 — CUT0 The cut-off brightness adjustment is made by simultaneously controlling
the external cut-off current.
(bit7 — 0)
V-AMP Control
Registers - 10
(Row 15,
Column 13)
HT
(bit 0)
HS3 — HS1
(bit3 — 1)
HS6 — HS4
(bit6 — 4)
SB
(bit 7)
30
Video & OSD half tone enable.
If you set this bit to 1
’ ,’ the half tone function is on.
Then you can see the video signal & OSD raster.
HS3 — HS1 bits select OSD raster color 1 to be half tone.
To carry out half tone function, set the HT bit to 1’ .’
OSD
G
R
B
Raster
Color 1
POR
0
0
0
0
Black
O
0
1
0
0
1
Blue
0
1
0
0
1
0
Red
0
1
1
0
1
1
Magenta
1
0
0
1
0
0
Green
1
0
1
1
0
1
Cyan
1
1
0
1
1
0
Yellow
1
1
1
1
1
1
White
HS3
HS2
HS1
0
0
0
HS6 — HS4 bits select OSD raster color 2 to be half tone.
To carry out half tone function, set the HT bit to 1’ .’
OSD
G
R
B
Raster
Color 2
POR
0
0
0
0
Black
O
0
1
0
0
1
Blue
0
1
0
0
1
0
Red
0
1
1
0
1
1
Magenta
1
0
0
1
0
0
Green
1
0
1
1
0
1
Cyan
1
1
0
1
1
0
Yellow
1
1
1
1
1
1
White
HS6
HS5
HS4
0
0
0
Soft blanking enable
If you set this bit 1’ ,’ the R/G/B outputs go to GND.
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Tabel 4. Register Description (Continued)
Registers
V-AMP Control
Registers - 11
(Row 15,
Column 14)
Bits
CS2 — CS1
(bit1 — bit0)
Description
Cut-off offset current control
CS2
CS1
Cut-off Offset Current
POR
0
0
0
O
0
1
50µA
1
0
100µA
1
1
150µA
BPW2 — BPW1 Generated clamp pulse width control
(bit4 — bit3)
BPW2
BPW1
Width
0
0
0.33µs
0
1
0.66µs
1
0
1.00µs
1
1
1.33µs
POR
O
To carry out this function, set the CLPS bit to " 0 "
V-AMP Control
Registers - 12
(Row 15,
Column 15)
BLKP
(bit 5)
Polarity of horizontral fly back signal
If this bit is 0’ ,’ HFLB’s polarity is negative, and if 1’ ,’ it is positive.
CLPP
(bit 6)
Polarity of clamp pulse signal
If this bit is 0’ ,’ CLP’s polarity is positive, and if 1
’ ,’ it is negative.
This bit has meaning only if the CLPS bit is set to 1’ .’
CLPS
(bit 7)
Clamp pulse generation enable
If this bit is 0’ ,’ clamp signal is made using the HFLB signal, so there is
no need to supply the clamp signal.
and if 1’ ’you must supply external clamp signal.
HS9 — HS7
(bit2 — bit 0)
HS9 — HS7 bits select OSD raster color 3 to be half tone.
To carry out half tone function, set the HT bit to " 1 ".
OSD
G
R
B
Raster
Color 3
0
0
0
0
Black
0
1
0
0
1
Blue
0
1
0
0
1
0
Red
0
1
1
0
1
1
Magenta
1
0
0
1
0
0
Green
1
0
1
1
0
1
Cyan
1
1
0
1
1
0
Yellow
1
1
1
1
1
1
White
HS9
HS8
HS7
0
0
0
POR
O
31
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
VIDEO AMP PART ADDRESS MAP
Register sub address (use limited to 1byte out of 2bytes)
Table 12. Video AMP Part Address Map
SUB Address
[Hex]
Function
D7
D6
D5
D3
D2
D1
D0
0F03
Contrast control
80H
0F04
Brightness control
80H
0F05
SUB contrast control (R)
80H
0F06
SUB contrast control (G)
80H
0F07
SUB contrast control (B)
80H
0F08
OSD contrast control
80H
0F09
Cut-off control (R)
80H
0F0A
Cut-off control (G)
80H
0F0B
Cut-off control (B)
80H
0F0C
Cut-off brightness control
80H
0F0D
SB
HS6
HS5
HS4
HS3
HS2
HS1
HT
00H
0F0E
CLPS
CLPP
BLKP
BPW2
BPW1
-
CS2
CS1
10H
0F0F
-
-
-
-
TST
HS9
HS8
HS7
00H
In normal status, you must set TST bit to 0
’ .’
32
D4
POR Value
[Hex]
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Contrast Register (SUB ADRS: 03H) (Vin = 0.7Vpp, bright: 80H, subcont: FFH)
Hex
B7
B6
B5
B4
B3
B2
B1
B0
Contrast (Vpp)
Gain (dB)
00
0
0
0
0
0
0
0
0
0
-
80
1
0
0
0
0
0
0
0
2.85
-
FF
1
1
1
1
1
1
1
1
5.2
-
Increment/bit
int. Value (Hex)
O
0.0223
Brightness Register (3-ch) (SUB ADRS: 04H) (cont: 80H, subcont: 80H)
Hex
B7
B6
B5
B4
B3
B2
B1
B0
Brightness (Vpp)
00
0
0
0
0
0
0
0
0
0.2
80
1
0
0
0
0
0
0
0
1.5
FF
1
1
1
1
1
1
1
1
2.7
Increment/bit
Int. Value (Hex)
O
0.01055
SUB Contrast Register (R/G/B-ch) (SUB ADRS: 05/06/07H)
(Vin = 0.7Vpp, bright: 40H, cont: FFH)
Hex
B7
B6
B5
B4
B3
B2
B1
B0
SUB Contrast
(Vpp)
Gain
(dB)
00
0
0
0
0
0
0
0
0
-
80
1
0
0
0
0
0
0
0
-
FF
1
1
1
1
1
1
1
1
-
Int. Value
(Hex)
O
Increment/bit
OSD Contrast Register (SUB ADRS: 08H) (VOSD = TTL, bright: 80H, subcont: 80H)
Hex
B7
B6
B5
B4
B3
B2
B1
B0
OSD Contrast
(Vpp)
Gain
(dB)
00
0
0
0
0
0
0
0
0
0
-
80
1
0
0
0
0
0
0
0
3.2
-
FF
1
1
1
1
1
1
1
1
6.4
-
Increment/bit
Int. Value
(Hex)
O
0.025
33
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Cut-Off Brightness Register (3-ch) (SUB ADRS: 0CH)
Hex
B7
B6
B5
B4
B3
B2
B1
B0
Cut-Off Brightness (µA)
00
0
0
0
0
0
0
0
0
0
80
1
0
0
0
0
0
0
0
100
FF
1
1
1
1
1
1
1
1
200
Increment/bit
Int. Value (Hex)
O
0.781
Cut-Off Register (R/G/B-ch) (SUB ADRS: 09/0A/0BH)
(cont = 80H, subcont: 80H)
Hex
B7
B6
B5
B4
B3
B2
B1
B0
Cut-Off EXT (µA)
00
0
0
0
0
0
0
0
0
0
80
1
0
0
0
0
0
0
0
300
FF
1
1
1
1
1
1
1
1
600
Increment/bit
34
2.344
Int. Value (Hex)
O
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
ADDRESSING
•
Display RAM Structure
Row Attribute Register
Virtual Register
Display RAM Address Area
Row
0
0
1
.
.
.
.
.
.
.
29
30
31
32
61
62
63
2
64
93
94
95
3
96
125 126 127
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
14
448
15
480 481 482 483 484 ... 495 496
.
.
.
.
.
.
.
477 478 479
511
Frame/V-AMP Control Registers
Figure 12. Display RAM Structure & Monitor Display Position
Whereas F
‘ igure 9. Memory Map of Display Registers’showed a logical configuration, the Figure above shows a
1KByte SRAM (512 × 16 bit)'s practical and physical configuration. For facilitating internal calculations, addressing
is done using exponents of 2, and the rows to the right of the 'Row Attribute Registers', excepting only IFF(255),
are 'Virtual Registers' that are not used.
If you set 'Frame Control Register 0's 'Erase' bit to '1', 480 areas are erased (excepting only the 16th line) in the
Figure above, and the 'Erasing Time' is measured with 480 areas as the standard.
35
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
•
ROM Fonts
S1D2502B01 provides 448 Rom fonts for displaying OSD Icons, which allows the use of multi-language OSD
Icons. Font $000 is reserved for blank data.
0
1
E
F
00
$000
$001
$00E
$00F
01
$010
$011
$01E
$01F
Standard
Fonts
1A
$1A0
$1A1
$1AE
$1AF
1B
$1B0
$1B1
$1BE
$1BF
1C
$1C0
$1C1
$1CE
$1CF
Figure 13. Composition of the ROM Fonts
36
Multi-Color
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
COLORING
If you have an Intensity feature, the number of possible colors you can express becomes doubled. In other words,
the number of colors you can represent with three colors blue, green, and red is 8 ( = 23), but with the intensity
feature, it is 16 ( = 24).
•
Character Color
Character color is assinged for each font, and the 4 components for expressing a color are listed below.
Blue
Character & attribute register's B bit[C]
Green
Character & attribute register's G bit[B]
Red
Character & attribute register's R bit[A]
Intensity
•
Character & attribute register's BLINK/FINT bit[9]
Row attribute register's INTE bit[D]
Row attribute register's CINT bit[4]
If all 3 bits are set to '1', the character intensity feature is enabled.
Raster Color
Blue
Row attribute register's RB bit[8] if the row attribute register's 'BOXE' bit is '1', and character
& attribute register's 'BINV' bit[F] if BOXE' bit is '0'.
Green
Row attribute register's RG bit[7] if row attribute register's 'BOXE' Bit is '1', and character &
attribute register's 'BOX1' bit[E] if 'BOXE' bit is '0'.
Red
Row attribute register's RR bit[6] if row attribute register's 'BOXE' bit is '1', and character &
attribute register's 'BOX0' bit[D] if 'BOXE' bit is '0'.
Intensity
Character & attribute register's BLINK/FINT bit[9]
Row attribute register's INTE bit[D]
Row attribute register's RINT bit[5]
If all 3 bits are set to '1', the raster intensity feature is enabled.
According to the 'BOXE' bit setting, raster color can be assigned in units of font or row. There is a trade-off in either
case. If 'BOXE' Bit is set to '1', the box drawing feature can be carried out in units of font, but the raster color can
only be assigned in units of row. On the other hand, if 'BOXE' bit is set to '0', the box drawing feature can't be
carried out, but you can assign raster color in units of font.
Notes for When Making S1D2502B01 Fonts
Address 000h is appointed as blank data. RAM's initial values are all 0, and all bits are written as 0 when you
erase the RAM, so blank data means the initial value. In other words, blank data means 'do nothing'. You don't
need to write any data for the space font, except for 000h. It just needs to be an undotted area.
37
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
•
Other Color Effet
The row attribute register's 'BREN' bit's function is shown in the Figure below. If you set the 'BREN' bit of the
row with the letter A as '0' after selecting A and B's raster color as black, the raster color black will be
displayed. But if you set the 'BREN' bit of the row with the letter B as '1', the raster color black becomes
invisible, so the back raster color (gray) is displayed as if it is the raster color.
Gray
BREN bit = 0 & Rastor Color = Black
BREN bit = 1 & Rastor Color = Black
BREN bit = 1 & Rastor Color = Light Blue
Figure 14. Color Effect by BREN Bit
Color blinking is using a selective control bit in blink mode to replace normal blinking with 8 different colors
appearing in order on the font's character. Color blinking only replaces normal blinking, and blink time and blink
duty are still applied at the same time. Therefore, if the blink duty is not set to off, only 3 ~ 4 colors may appear
according to the blink duty, instead of all 8.
SIZING/POSITIONING
•
Character Size
Row attribute register's HZ bit[3:2] and VZ bit[1:0] control the character's vertical and horizontal size by factors
of 1/2/3/4 in units of row. VZ is correctly expressed without regard to size since the next line is just pushed
down in order, but HZ decides the column that the font occupies according to the size. For example, if HZ [1:0]
= 0, 1, the font doubles in the horizontal direction, and one font takes up 2 columns. Therefore, the column
address must move in the same amount as the HZ for the next font to be expressed correctly. in other words, if
the horizontal size is doubled and takes up 2 columns, the next font must be put 2 columns back.
Original
HZ × 2
VZ × 2
Figure 15. Character Size by VZ, HZ Bits
38
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
•
S1D2502B01
Character Height
Whereas the purpose of VZ[1:0] (Vertical Character Height) is to adjust the character's absolute size, the
purpose of CH[5:0] (Character Height) is to output a uniformly sized OSD even if the resolution changes. To
express a Character Height of CH = 18 ~ CH = 63 after receiving CH[5:0]'s input from the frame control
register-1, decide on each line's repeating number (Standard Height CH = 18) and repeat the lines.
The following Figure shows two examples of a height-controlled character. height control is carried out by
repeating some of the lines.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
: added
line
Standard font
in high vertical resolution
Standard Font(12*18)
Height-controlled font
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Standard Font(12*18)
: added
line
Standard font
in more higher vertical resolution
Height-controlled font
Figure 16. Character Height
39
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Repeating line-number can be found by the following formula.
[# of the repeating lines = 2 + N × M],
where N = 1, 2, 3, ... and M = round{14 ÷ (CH[5:0]-18)}.
1. If CH[5:0] is greater than 32 and less than or equal to 46 (32 < CH[5:0] ≤ 46), all lines are repeated once or
twice. The lines that are repeated twice are chosen by the following formula.
[# of the repeating lines = 2 + N × M],
where N = 1, 2, 3, ... and M = round {14 ≤ (CH[5:0]-32)}.
2. If CH[5:0] is greater than 46 and less than or equal to 60 (46 < CH[5:0] ≤ 60), all lines are repeated two or three
times. The lines that are repeated three times are chosen by the following formula.
[# of the repeating lines = 2 + N × M],
where N = 1, 2, 3, ... and M = round {14 ≤ (CH[5:0]-46)}.
3. If CH[5:0] is greater than 60 and less than or equal to 64 (60 < CH[5:0] ≤ 64), all Lines are repeated three or four
times. The lines that are repeated four times are chosen by the following formula.
[# of the repeating lines = 2 + N x M],
where N = 1, 2, 3, ... and M = round {14 ≤ (CH[5:0]-60)}.
CH's reference value is 18, and even if you input 0, it operates in the same way as when CH = 18. The repeating
line-number is limited to 16. If the M value is less than or equal to 1, all lines of the standard font are repeated more
than once.
Table 13. Repeating Line as Controlling by CH bits
Character Height
Repeating Line
CH = 18
-
CH = 19
9
CH = 20, 21
6, 13
CH = 22
5, 11, 17
CH = 23
4, 9, 14, 19
CH = 24
3, 7, 11, 15, 19, 21
CH = 25, 26, 27
3, 7, 11, 13, 15, 19, 22
CH = 28
3, 6, 9, 12, 14, 18, 20, 23, 25
CH = 29
3, 6, 9, 11, 13, 15, 18, 21, 23, 25, 26
CH = 30
3, 6, 8, 10, 12, 14, 16, 18, 20, 22, 25, 27
CH = 31
2, 5, 7, 9, 11, 13, 15, 17, 21, 23, 25, 27, 28
CH = 32, 33, 34, 35
2, 5, 7, 9, 11, 13, 15, 18, 21, 23, 25, 27, 28, 29
CH = 36
-
CH = 37
18
40
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
Table 13. Repeating Line as Controlling by CH bits
Character Height
Repeating Line (Continued)
CH = 38, 39
12, 25
CH = 40
10, 20, 30
CH = 41
8, 16, 24, 32
CH = 42
6, 12, 18, 24, 30, 36
CH = 43, 44, 45
6, 12, 18, 24, 30, 36, 41
CH = 46
4, 8, 12, 17, 21, 25, 29, 33, 37, 41
CH = 47
4, 8, 12, 16, 20, 24, 28, 32, 36, 40, 44
CH = 48
4, 8, 12, 16, 20, 23, 26, 29, 33, 37, 41, 45
CH = 49
4, 8, 12, 16, 19, 22, 25, 28, 31, 35, 39, 43, 47
CH = 50, 51, 52, 53
4, 8, 12, 15, 18, 21, 24, 27, 30, 33, 36, 40, 44, 48
CH = 54
-
CH = 55
27
CH = 56, 57
18, 36
CH = 58
14, 28, 42
CH = 59
12, 23, 34, 45
CH = 60
9, 18, 26, 34, 43, 52
CH = 61, 62, 63
8, 16, 23, 30, 37, 44, 51
41
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
•
Positioning
The frame control register-2's HP Bit [F:8] signifies delay of the horizontal display from the H-Sync reference
edge to the character's 1st pixel location, and is controlled by multiplying HP [F:8]'s range value by 6. Also, VP
bit[7:0] signifies the top margin height from the V-Sync reference edge, and is controlled by multiplying 4 to the
VP [7:0]'s range value. Refer to the Figure shown below.
(HFLB)
VP[7:0]
HP[7:0]
OSD characters
30 columns (= 30 x 12 dots)
15 rows
(=15 x 18 lines)
(VFLB)
Background Screen
Figure 17. Frame Composition with the OSD Characters
42
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
VISUAL EFFECTS
•
Box Drawing
Set the row attribute register's boxe bit to '1' and enable the box feature. Then set the character & attribute
register's BOX bit to select one of 4 modes. Or, use the character & attribute register's BINV bit to inverse the
white and black areas of the box mode selected by the BOX bit.
BOX0
o
BOX1
1
0
BOX OFF
A
1
A
A
Figure 18. Box Drawing
The principle behind the boxing feature is shown below.
HDOT0
HDOT11
BOX<1:0> 01
DOTLINE_ H
17
0
DOTLINE_ H
DOTLINE_ H
DOTLINE_ H
DOTLINE_ H
DOTLINE_ H
17
17
0
0
BOX<1:0> 10
BOX<1:0> 11
Out of the 12 horizontal dots and 18 vertical lines that make 1 character, make the first and 12th horizontal dots to
HDOT0/HDOT11, and the first and 18th vertical lines to DOTLINE-0H/DOTLINE-17H in order to carry out box
drawing for 1 dot outside the character.
43
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
•
Bordering/Shadowing
The character border and shadow can only be black. Character border is the effect where you make 1 pixel
around the character, and character shadow is making 1 pixel to the right and below the character.
Bordering
Shadowing
Figure 19. Character Bordering/Shdowing
•
Scrolling
Scrolling is slowly displaying or erasing a character from the top line to the bottom. This effect makes it look as
if 1 character line is scrolling up or down.
Figure 20. Scrolling
44
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
•
S1D2502B01
Fade-In/Fade-Out
Fade-in/fade-out is displaying from the center to the outside in units of font when OSD display is on/off. Each
font's display is turned on/of without regard to size, in units of (12 × 18) dot.
Also, to control the fade in/out time, the V_PULSE's 1/4, 1/8 clocks are used for counting. In other words, as
control data, it takes 0.5sec if the frame control register - 0's 'FdeT' bit is 1, and 1sec if 0. If it is difficult to
visualize the fade-in / fade-out feature with the explanation and diagrams in this document, write the control
data to the OSD IC and verify the IC's operations. Like the scrolling feature, fade in/out can only be verified
when OSD is enabled/disabled.
Fade in/out
Unit: Font
6CK_Time
6CK_Time + 3CK_Time
row Space
Display at 9CK_Time
Figure 21. Fade-In/Fade-Out
45
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
PLL CONTROL
•
Introduction
PLL (Phase Lock Loop) is feedback controlled circuit that maintains a constant phase difference between a
reference signal and an oscillator output signal.
Generally, PLL is composed as follow Figure.
Reference Signal
PFD
(Phase Frequency Detector)
LF
(Loop Filter)
VCO (Voltage
Controlled Oscillator)
FD
(Frequency Detector)
Figure 22. Block Diagram of General PLL
- PFD (Phase Frequency Detector)
PFD compares the phase of the VCO output frequency, with the phase of a reference signal frequency output
pulse is generated in proportion to that phase difference.
- LF (Loop Filter)
LF smooths the output pulse of the phase detector and the resulting DC component is the VCO input.
- VCO (Voltage Controlled Oscillator)
VCO is controlled by loop filter output. The output of the VCO is fed back to the phase frequency detector
input for comparison which in turn controls the VCO oscillating frequency to minimize the phase difference.
- FD (Frequency Divider)
FD divides too much different frequency that is oscillated from the VCO to compare it with reference signal
frequency.
46
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
•
S1D2502B01
PLL of the S1D2502B01
PLL is composed of the phase detector, charge pump, VCO, and N-divider as 4 sub-blocks.
Loop
Filter
# Composed of External Components
CP_out
(Pin4)
HFLB (Pin32)
Phase
Detector
VCO_in
(Pin3)
Charge
Pump
VCO_out
VCO
Div_out
N-Divider
CP0
CP1
DOT0
DOT1
HF0 HF1 HF2
Figure 23. Block Diagram of the PLL Built in S1D2502B01
The following is the description of the input/output signals.
- HFLB (Input)
Horizontal flyback signal is refrence signal of the PLL built in S1D2502B01.
The HFLB signal's frequency range is 15 ~ 90kHz, so the PLL block must be a wide range PLL that can cover
HFLB's entire frequency range.
> 4.2V
< 0.4V
fHFLB
~2us
- VCO (Input)
Error signal that passes through an external loop filter is input into VCO.
Operation voltage range is 1-4V. You can raise immunity towards external noise by lowering VCO
sensitivity. You can do this by making it have the maximum operation voltage range possible in the 5V power
voltage.
47
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
- DOT0, 1 (Input)
Mode control signal that controls the number of dots per line in the frame control register. There are 4 modes:
320, 480, 640, and 800 dots/line.
According to your choice of mode, the OSD_PLL block's N-Divider is controlled by one of ÷320, ÷480, ÷640, or
÷800 Divider.
- HF0, 1, 2 (Input)
The horizontal Sync frequency information is received from the micro controller through the frame control
registers-1's bit C-A.
- CP0, 1 (Input)
Charge Pump's output sourcing (or sinking) current control pin.
This control data is received through frame control registers-1's bits E-D.
- VCO_OUT (Output)
VCO output that becomes a system clock. It is the OSD R, G, B output signal's dot frequency, and the standard
signal for OSD's various timings.
Also, it is input into the N-Divider and makes a PLL loop
> 4.2V
< 0.4V
fclk
Rise Time : < 4nS
Fall Time : < 4nS
- CP_OUT (Output)
Charge Pump circuit's output. input into external loop filter. It becomes one of 3 states according to the standard
signal input into the phase detector (HFLB) and the divider output (Div_Out).
- HFLB Div_Out is lead: Current sink
- HFLB Lag: Current source
- HFLB In-Phase: High impedence
48
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
TUNNING FACTORS OF THE S1D2502B01 PLL
•
PLL External Circuit
You may follow the recommendations for PCB art work and input/output signal characteristic improvement in
recommendation.
The external circuit that has the most influence on S1D2502B01 PLL block operation is pin 3 (VCO_IN) and pin
4 (CP_OUT)'s surrounding circuit. Refer to OSD PLL block.
3
4
C1
R1
R3
R2
(option)
Figure 24. PLL External Circuit
Because the PLL circuit is basically a feedback circuit, there are many components that influence the
characteristics. C1, R1, R2, and R3 do not have a localized effect.
As you can see, they are connected to the PLL control bits and influence the characteristics through their
complicated relationships. The main functions of the time canstant and their reference values are as follows.
Table 14. Main Function of Time Constant in PLL External Circuit
Time Canstant
Recommended Value
Main Function
C1
562 (or 103, 223)
R1
5.6KΩ(7.5KΩ)
R2
27KΩ (or 33KΩ)
Charge pump current adjustment
R3 (Option)
30MΩ (or 20MΩ)
Extend frequency range
Influences the damping ratio and controls the PLL
response time
Same as C1
49
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
•
PLL Control Bit
After configuring an external circuit using the recommended values, carry out programming using the
recommended values for frequency range and control bits given in the Table below.
Table 15. Recommend Values of PLL Control Bit
Register Set
PLL Control Bit
Freq. Range
CP1
CP0
FPLL
HF2
HF1
HF0
DOT1
DOT0
Hex
Below 40kHz
0
0
0
0
1
0
1
1
0B
40 - 50kHz
1
0
0
1
0
0
1
1
93
50 - 70kHz
1
0
0
1
0
1
1
1
97
Above 70kHz
1
0
0
1
1
1
1
1
9F
(Ref: 800 × 600, C1: 562, R1: 5.6K, R2: 27K, R3: 30M)
•
Locking Range
As you can see the figure below, it is 2.35V that measured voltage at pin-3 to optimize OSD quality. The proper
voltage range is 1.5 ~ 3.25V.
Locking Range
4V
3.25V
2.37V
1.625V
1.5V
Ve (min)
0.75V
f0
fC
-2¥ð
fL
Figure 25. Locking Range
50
2¥ð
fmax
Ve (max)
1.625V
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
•
S1D2502B01
HF Bits Selection
HF bits is not selecting from out of 8 (23) steps uniformly, but selecting the step shown in figure below. In
example, at 800 mode, there are 5 steps that the frequency range is controlled by HF bits.
Table 16. HF Bits Selection
DIV
DOT1
DOT0
320
0
0
480
0
1
640
1
0
800
1
1
HF2
HF1
HF0
After fixing time constants of the external circuit and PLL control bits except HF bits, if HF bits are stepped up, the
voltage measured at pin-3 drops. On the contrary, if HF bits are stepped down, the voltage rises.
The voltage measured at pin-3 don't change by changing CP bits.
•
External Register at pin-4
The external register at pin-4 is the factor that changes greatly at PLL tunning. The initial value of this external
register value is decided as follows.
At first, the external register is replaced variable-register (about 50KΩ range).
and then, set the lowest PLL control bits at the lowest frequency allowed by set.
and then, change variable-register to be 2.35V that optimum voltage is locking.
and then, measure register value at this time.
also, set the highest PLL control bits at the highest frequency allowed by set.
and then, change variable-register to be 2.35V that optimum voltage is locking.
and then, measure register value at this time.
You may decide the average of these two registers' value to initial value.
51
S1D2502B01
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
The table below shows that other factors change as changing external register's value.
Fixing Factor
Variable Factor
Time constants of the external circuit
and PLL control bits except
Rext
52
Change
Voltage
Current
Lock Range
↑
↑
↓
↓ (shift)
↓
↓
↑
↑ (shift)
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
RECOMMENDATION
5V Power Routing
S1D2502B01's OSD part power is composed of analog VDD and digital VDD. To eliminate clock noise influence in
the digital block, you need to separate the analog VDDA and digital VDD.
(BD102 use: Refer to Application Circuit )
12V Power Routing
Because S1D2502B01 is a wideband AMP of above 150MHz, 12V power significantly affects the video
characteristics. The effects from the inductance and capacitance are different for each board, and , therefore,
some tuning is required to obtain the optimum performance. The output power, VCC2, must be separated from
VCC1 and VCC3 using a coil, which is parallel-connected to the damping resistor.The appropriate coil value is
between 20uH - 200uH. Parallel-connected a variable resistor to the coil and control its resistance to obtain the
optimum video waveform.
(Moreover, BD103 can tune using a coil and variable resistor to obtain the optimum video waveform.
L103, R124, BD103: Refer to application circuit)
VCC1, VCC3 12V Power
Use a 104 capacitor and large capacitor greater than 470uH for the power filter capacitor.
12V Output Stage Power VCC2
Do not use the power filter capacitor.
5V Digital Power VDD
Don't use a coil or magnetic core to the VDD input. Make the power filter capacitor, an electric capacitor of greater
than 50uF, single and connect it to VSS, the digital GND.
Output Stage GND2
Care must be taken during routing because it ,as an AMP output stage GND, is an important factor of video
oscillation. R/G/B clamp cap and R/G/B load resistor must be placed as close as possible to the GND2 pin. GND2
must be arranged so that it has the minimum GND loop, which at one point must be connected to the main GND.
Digital GND VSS
When this is to be connected directly to the GND2, it can cause the OSD clock noise, so the loop connection
should be routed as far away as possible. If the OSD clock noise affects the screen, separate VSS GND from all
GND and connect it to the main board using a bead. Again, the bead connection point should be placed as far
away as possible to the GND2.
Analog Block
The PLL built in to S1D2502B01 is sensitive to noise due to the wide range PLL characteristics. Therefore, you
need to isolate the analog block in the following manner. First make a separate land for the analog block (pin2 pin6)'s ground, and connect it to the main ground through a 1MΩ resistor. The analog GND of both sides of a
double faced PCB must be separated from the main ground. (Separate pin 2's 5V analog GND, which is the GND
for OSD PLL, from the main and digital GNDs and connect it to the main GND using about 1MΩ resistor. GND for
pins 2 - 6 is the No. 2 VSSA GND.)
53
S1D2502B01
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
I2C Control Line (SCL, SDA Line)
I2C communication noise (noise generated in the OSD display pattern when data is transmitted in the I2C line) may
be generated because of an I2C control line that passes near the analog block. The I 2C control lines near
S1D2502B01 must be separated from the analog block as much as possible.
Furthermore, the I2C bus interference can be prevented by inserting a series resistor in the line.
Horizontal Flyback Signal
Display jittering can be generated if the horizontal signal (HFLB) input to S1D2502B01 is not a clean signal.
We recommend a short path and shielded cable for obtaining a clean signal.
Generally, the input horizontal signal (HFLB) is generated by using a high voltage horizontal flyback signal. The
effect from the high voltage flyback signal can be reduced by separating the R115 and R117 GND, which
determines the flyback signal slice level, from the transistor GND, which generates the actual S1D2502B01 input
horizontal signal. Furthermore, the flyback signal sharpness must be maintained by minimizing the values of R115,
R116 and R117 resistors, which set the horizontal signal slice level. values.
(R115, R116, R117: Refer to application circuit )
HFLB Input Signal Generator
You can correct the circuit by reducing the resistors that sets the slice level of the horizontal signal in the HFLBgenerating circuit.
54
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
APPLICATION BOARD CIRCUIT
CN1
CN2
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1N4148
DR01
DG02
1N4148
DG01
6.3V
DB02
1N4148
DB01
103
1N4148
12V
DR02
70V
C123
R123
C109
1N4148
1M
103
C114
1N4148
C124
103
103
RB01
RG01
C110
C111
75
RG02
75
RR02
75
+
12V
100uH
RR01
75
RB02
75
+
75
L101
4.7uF
100uF
BD102
5V
R107
1K
C102
CR01
104
C112
1uF
1uF
R101
R108
5.6K
+
CG02
104
+
CB02
104
R109
27K
4.7K
30M
1
2
3
4
5
6
VFLB
VSSA
VCO_IN
VREF1
VREF
VDDA
+
470uF
BD103
VDD
HFLB
SDA
SCL
VSS
RCT
GCT
BCT
ROUT
RCLP
VCC2
GCLP
GOUT
104
C128
560
104
560
C160
+
10K
32
31
30
29
28
27
26
25
24
23
22
21
20
19
R119
R116
1N4148
104
C103
R118
330pF
D102
18
17
150
C152
C151
G1
C118
GND2
1.8nF
BOUT
BCLP
C126
R117
CONT_CAP
KB2502
WSP-401M
1nF
7
ABL_IN
GND
CLP_IN
VCC3
RIN
VCC1
GIN
SK101
C116
8
9
10
11
12
13
14
GND1
BIN
5V
R103
390
15
16
102
1nF
12_1V
100
C119
C117
C113
562
R120
R102
47uF
R115
R124
2K
220
2
12V
L103
27uH
R114
3
Q102
2N3904
470
CB02
CG02
CR02
104
104
104
RG03
RB03
5V
1
RR03
470
470
470
RG15
47
RB15
47
RB04
100
RG04
100
CB08
270pF
RR15
47
9
GND
VCC
DRIVER IC
RIN
GIN
+
5
4
3
2
70V
RG08
56
CG07
37pF
RB08
56
CB07
37pF
RG14
75
RB14
75
104
LR01
0.15uH
2.2K
LG01
0.15uH
LB01
0.15uH
3
3
3
2
QG02
2N5401C-Y
DB03
2
QR02
2N5401C-Y
DB04
1SS244
DG03
1
1
1
RB13
82K
RG13
82K
RR13
82K
DG05
1N4148
DG04
1SS244
VDD
DB05
1N4148
CR07
37pF
RR14
75
RR12
2.2K
2
RR08
56
CR05
104
RG12
2.2K
C108
47uF
104
CG05
104
RB12
104
CR05
104
CB05
7
CG05
104
C121
3
3
3
CB05
QB02
2N5401C-Y
2
1
2
C107
QR01
220uF
2N5551C-Y
BOUT
QG01
2N5551C-Y
CR08
270pF
CR08
270pF
+
2
104
1
1
1
QB01
2N5551C-Y
C106
BIN
4.7K
ROUT
RR20
4.7K
VBB GOUT
RR11
100
RG20
4.7K
6
8
RG11
100
12V
RB11
100
RB20
RR04
100
RR04
100
CG08
270pF
DR03
DR04
1SS244
DR05
1N4148
+
+
CR04
1uF
1SS244
+
CG04
1uF
1SS244
1SS244
CB04
1uF
RR09
RG09
RB09
75K
75K
75K
G2
R104
390
RR10
39
SK102
SKB01
DMS-200D
RG10
39
RB10
39
DMS-200D
SKG01
C120
1nF
DMS-200D
G2
DMS-200D
SKR01
B_OUT
G_OUT
R_OUT
Figure 26. Application Board Circuit
55
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
TYPICAL APPLICATION CIRCUIT
CN1
CN2
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1N4148
DR01
DG02
1N4148
DG01
6.3V
DB02
1N4148
DB01
103
1N4148
12V
DR02
70V
C123
R123
1N4148
C109
1M
103
C114
1N4148
C124
103
103
RB01
RG01
C110
C111
75
RG02
75
RR02
75
+
12V
100uH
RR01
75
RB02
75
+
75
L101
4.7uF
100uF
BD102
5V
R107
1K
C102
CR01
104
C112
4.7K
R120
R102
30M
12_1V
1
2
3
4
5
6
VFLB
VSSA
VCO_IN
VREF1
VREF
VDDA
104
+
470uF
BD103
VDD
HFLB
SDA
SCL
VSS
RCT
GCT
BCT
ROUT
RCLP
VCC2
GCLP
GOUT
104
C128
560
104
560
10K
32
31
30
29
28
27
26
25
24
23
22
21
20
19
R119
R116
C160
+
1N4148
C152
C103
R118
330pF
D102
18
150
C113
562
C151
17
C118
GND2
1.8nF
G1
R117
BOUT
BCLP
C126
1nF
CONT_CAP
KB2502
WSP-401M
7
ABL_IN
GND
CLP_IN
VCC3
RIN
VCC1
GIN
SK101
C116
8
9
10
11
12
13
14
GND1
BIN
5V
R103
390
15
16
102
1nF
R108
5.6K
R109
27K
100
C119
C117
1uF
1uF
R101
+
CG02
104
+
CB02
104
47uF
R115
R124
2K
220
2
12V
L103
27uH
R114
3
470
Q102
2N3904
CB02
CG02
CR02
104
104
104
RG03
RB03
RR03
470
470
470
RG15
47
RB15
47
RR15
47
9
7
GND
VCC
BOUT
GOUT
DRIVER IC
RIN
GIN
BIN
VBB
ROUT
+
5
4
3
1
2
+
70V
3
3
3
104
RG12
RR12
2.2K
2.2K
2.2K
RR14
75
RG14
75
RB14
75
3
3
3
2
47uF
CR05
104
RB12
QB02
2N5401C-Y
C108
104
CG05
104
104
CR05
104
CB05
C121
C107
QR01
220uF
2N5551C-Y
2
CG05
104
104
1
QG01
2N5551C-Y
2
CB05
C106
4.7K
1
1
QB01
2N5551C-Y
2
RR11
100
RR20
4.7K
6
8
RG11
100
RG20
4.7K
12V
RB11
100
RB20
2
QG02
2N5401C-Y
DB03
2
QR02
2N5401C-Y
DB04
1SS244
1
1
1
DG03
RB13
82K
RG13
82K
RR13
82K
1SS244
VDD
DB05
DG05
DR05
1N4148
1N4148
1N4148
DG04
DR03
DR04
1SS244
1SS244
1SS244
1SS244
+
+
CR04
1uF
+
CG04
1uF
CB04
1uF
RR09
RG09
RB09
75K
G2
LR01
LG01
0.15uH
0.15uH
LB01
0.15uH
R104
390
RR10
39
SK102
SKB01
DMS-200D
RG10
39
RB10
39
DMS-200D
SKG01
C120
1nF
DMS-200D
G2
DMS-200D
SKR01
B_OUT
G_OUT
R_OUT
Figure 27. Typical Application Circuit
56
75K
75K
5V
1
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
ROM FONTS
Figure 28. ROM Fonts
57
S1D2502B01
58
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01
59
S1D2502B01
60
Preliminary
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS