FAIRCHILD FIN3386MTDX

FIN3385 / FIN3386
Low-Voltage, 28-Bit, Flat-Panel Display Link
Serializer / Deserializer
Features
Description









The FIN3385 and FIN3386 transform 28-bit wide parallel
Low-Voltage TTL (LVTTL) data into four serial Low
Voltage Differential Signaling (LVDS) data streams. A
phase-locked transmit clock is transmitted in parallel
with the data stream over a separate LVDS link. Every
cycle of transmit clock, 28-bits of input LVTTL data are
sampled and transmitted.
Operation -40°C to +85°C
Low Power Consumption
20MHz to 85MHz Shift Clock Support
±1V Common-Mode Range around 1.2V
Narrow Bus Reduces Cable Size and Cost
High Throughput (up to 2.38Gbps)
Internal PLL with No External Component
Compatible with TIA/EIA-644 Specification
56-Lead, TSSOP Package
The FIN3386 receives and converts the 4/3 serial LVDS
data streams back into 28/21 bits of LVTTL data, acting
as the deserializer.
For the FIN3385, at a transmit clock frequency of
85MHz, 28-bits of LVTTL data are transmitted at a rate
of 595Mbps per LVDS channel.
This pair solves EMI and cable size problems
associated with wide and high-speed TTL interfaces.
Ordering Information
Part Number
Operating
Temperature Range
Package
Packing
Method
-40 to +85°C
56-Lead Thin-Shrink Small-Outline Package
(TSSOP), JEDEC MO-153,6.1mm Wide
Tape and Reel
FIN3385MTDX
FIN3386MTDX
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
March 2012
Figure 1. FIN3385 Transmitter Functional Diagram
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Block Diagrams
Figure 2. FIN3386 Receiver Functional Diagram
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
2
Figure 3. FIN3385 (28:4 Transmitter) Pin Assignments
Pin Definitions
Pin Names
I/O Types
Number of Pins
TxIn
I
28/21
Description of Signals
LVTTL Level Input
TxCLKIn
I
1
TxOut+
O
4/3
Positive LVDS Differential Data Output
LVTTL Level Clock Input, the rising edge is for data strobe
TxOut-
O
4/3
Negative LVDS Differential Data Output
TxCLKOut+
O
1
Positive LVDS Differential Clock Output
TxCLKOut-
O
1
Negative LVDS Differential Clock Output
R_FB
I
1
Rising Edge Data Strobe: Assert HIGH (VCC)
Falling Edge Data Strobe: Assert LOW (Ground)
/PwrDn
I
1
LVTTL Level Power-Down Input Assertion (LOW) puts the
outputs in High-Impedance state
PLL VCC
I
1
Power Supply Pin for PLL
PLL GND
I
2
Ground Pins for PLL
LVDS VCC
I
1
Power Supply Pin for LVDS Output
LVDS GND
I
3
Ground Pins for LVDS Output
VCC
I
3
Power Supply Pins for LVTTL Input
GND
I
5
Ground Pin for LVTTL Input
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Transmitter Pin Configuration
www.fairchildsemi.com
3
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Receiver Pin Configuration
Figure 4. FIN3386 (28:4 Receiver) Pin Assignments
Pin Definitions
Pin Names
I/O Types
Number of Pins
RxIn
I
4/3
Negative LVDS Differential Data Output
RxIn+
I
4/3
Positive LVDS Differential Data Output
RxCLKIn-
I
1
Negative LVDS Differential Data Input
Positive LVDS Differential Clock Input
RxCLKIn+
I
1
RxOut
O
28/21
RxCLKOut-
O
1
Description of Signals
LVTTL Level Data Output, goes HIGH for /PwrDn LOW
LVTTL Clock Output
/PwrDn
I
1
LVTTL Level Input. Refer to Table 2
PLL VCC
I
1
Power Supply Pin for PLL
PLL GND
I
2
Ground Pins for PLL
LVDS VCC
I
1
Power Supply Pin for LVDS Input
LVDS GND
I
3
Ground Pins for LVDS Input
VCC
I
4
Power Supply for LVTTL Output
GND
I
5
Ground Pins for LVTTL Output
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
4
Table 1. Input / Output Truth Table
Inputs
Outputs
(1)
TxIn
TxCLKIn
/PwrDn
Active
Active
Active
LOW / HIGH / High Impedance
TxOut±
TxCLKOut±
HIGH
LOW / HIGH
LOW / HIGH
HIGH
LOW / HIGH
Don’t Care(2)
Floating
Active
HIGH
LOW
LOW / HIGH
Floating
Floating
HIGH
LOW
Don’t Care(2)
Don’t Care
Don’t Care
LOW
High Impedance
High Impedance
Notes:
1. The outputs of the transmitter or receiver remain in a high-impedance state until VCC reaches 2V.
2. TxCLKOut± settles at a free-running frequency when the part is powered up, /PwrDn is HIGH, and the TxCLKIn
is a steady logic level (LOW / HIGH / High-Impedance).
Power-Up / Power-Down Operation Truth Tables
The outputs of the transmitter remain in the High-Impedance state until the power supply reaches 2V. Table 2 shows
the operation of the transmitter during power-up and power-down and operation of the /PwrDn pin.
Table 2. Transmitter Power-Up / Power-Down Operation Truth Table
VCC
<2V
PwrDn
Normal
>2V
>2V
TxIN
Don’t Care
Don’t Care
Active
TxOUT
High Impedance
High Impedance
Active
TxCLKIn
Don’t Care
Don’t Care
Active
TxCLKOut±
High Impedance
High Impedance
Active
/PwrDn
LOW
LOW
HIGH
Table 3. Receiver Power-Up / Power-Down Operation Truth Table
/PwrDn
RxIn±
Don’t Care
RxOut
High
Impedance
Don’t Care
Active
LOW
LOW/HIGH
RxCLKIn±
Don’t Care
Don’t Care
RxCLKOut
High
Impedance
/PwrDn
VCC
Active
Note 3
Note 3
Last Valid State
HIGH
Last Valid
State
Active
Note 3
Note 3
Note 3
Note 4
Active
Note 4
Note 4
Note 4
LOW
LOW
HIGH
HIGH
HIGH
HIGH
<2V
<2V
<2V
<2V
<2V
<2V
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Truth Tables
Notes:
3. If the input is terminated and un-driven (high-impedance) or shorted or open (fail-safe condition).
4. For /PwrDn or fail-safe condition, the RxCLKOut pin goes LOW for panel link devices and HIGH for channel link
devices.
5. Shorted means (± inputs are shorted to each other, or ± inputs are shorted to each other and ground or VCC, or
either ± inputs are shorted to ground or VCC) with no other current/voltage sources (noise) applied. If the VID is still
in the valid range (greater than 100mV) and VCM is in the valid range (0V to 2.4V), the input signal is still
recognized and the part responds normally.
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
5
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Symbol
Min.
Max.
Unit
Power Supply Voltage
-0.3
+4.6
V
VID_TTL
TTL/CMOS Input/Output Voltage
-0.5
+4.6
V
VIO_LVDS
LVDS Input/Output Voltage
-0.3
+4.6
V
VCC
Parameter
IOSD
LVDS Output Short-Circuit Current
TSTG
Storage Temperature Range
Continuous
-65
+150
°C
TJ
Maximum Junction Temperature
+150
°C
TL
Lead Temperature, Soldering, 4 Seconds
+260
°C
ESD
Human Body Model, JESD22-A114 (1.5k,100pF)
I/O to GND
>10.0
All Pins
>6.5
>400
Machine Model, JESD22-A115 (0, 200pF)
kV
V
Note:
6. Absolute maximum ratings are DC values beyond which the device may be damaged or have its useful life
impaired. The datasheet specifications should be met, without exception, to ensure that the system design is
reliable over its power supply, temperature, and output/input loading variables.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to Absolute Maximum Ratings.
Symbol
Parameter
VCC
Supply Voltage
TA
Operating Temperature
VCCNPP
(7)
Maximum Supply Noise Voltage
Min.
Max.
Unit
3.0
3.6
V
-40
+85
°C
100
mVPP
Note:
7. 100mV VCC noise should be tested for frequency at least up to 2MHz. All the specifications should be met under
such noise.
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Absolute Maximum Ratings
www.fairchildsemi.com
6
Typical values are at TA=25°C and with VCC=3.3V; minimum and maximum are at over supply voltages and operating
temperatures ranges, unless otherwise specified.
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
Transmitter LVTTL Input Characteristics
VIH
Input HIGH Voltage
2.0
VCC
V
VIL
Input LOW Voltage
GND
0.8
V
VIK
Input Clamp Voltage
-0.79
-1.50
V
1.8
10.0
IIN
Input Current
IIK=-18mA
VIN=0.4V to 4.6V
µA
VIN=GND
-10
0
Transmitter LVDS Output Characteristics(8)
VOD
VOD
VOS
VOS
250
Output Differential Voltage
VOD Magnitude Change from Differential
LOW-to-HIGH
Offset Voltage
RL=100, Figure 5
Offset Magnitude Change from
Differential LOW-to-HIGH
1.125
1.250
450
mV
35
mV
1.375
V
25
IOS
Short-Circuit Output Current
VOUT=0V
IOZ
Disabled Output Leakage Current
DO=0V to 4.6V,
/PwrDn=0V
mV
-3.5
-5.0
mA
±1
±10
µA
32.5MHz
31.0
49.5
40MHz
32.0
55.0
66MHz
37.0
60.5
85MHz
42.0
66.0
10.0
55.0
32.5MHz
29.0
41.8
40MHz
30.0
44.0
66MHz
35.0
49.5
85MHz
39.0
55.0
Transmitter Supply Current
ICCWT
ICCPDT
ICCGT
28:4 Transmitter Power Supply Current
for Worst-Case Pattern (with Load)(9)
Powered-Down Supply Current
28:4 Transmitter Supply Current for
16 Grayscale(9)
RL=100
Figure 8
mA
/PwrDn=0.8V
(10)
µA
mA
Figure 23
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Transmitter DC Electrical Characteristics
Notes:
8. Positive current values refer to the current flowing into device and negative values refer to current flowing out of
pins. Voltages are referenced to ground unless otherwise specified (except VOD and VOD).
9. The power supply current for both transmitter and receiver can vary with the number of active I/O channels.
10. The 16-grayscale test pattern tests device power consumption for a “typical” LCD display pattern. The test
pattern approximates signal switching needed to produce groups of 16 vertical strips across the display.
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
7
Typical values are at TA=25°C and with VCC=3.3V; minimum and maximum are at over supply voltages and operating
temperatures ranges, unless otherwise specified.
Symbol
Parameter
Condition
tTCP
Transmit Clock Period
tTCH
Transmit Clock (TxCLKIn) HIGH Time
tTCL
Transmit Clock LOW Time
tCLKT
TxCLKIn Transition Time (Rising and Falling)
tJIT
TxCLKIn Cycle-to-Cycle Jitter
tXIT
TxIn Transition Time
Figure 9
(10% to 90%)
Figure 10
Min.
Typ.
Max.
Unit
11.76
T
50.00
ns
0.35
0.50
0.65
T
0.35
0.50
0.65
T
1.0
6.0
ns
3.0
1.5
6.0
ns
0.75
1.50
ns
0.75
1.50
ns
LVDS Transmitter Timing Characteristics
tTLH
Differential Output Rise Time (20% to 80%)
tTHL
Differential Output Fall Time (20% to 80%)
tSTC
TxIn Setup to TxCLNIn
tHTC
TxIn Holds to TxCLNIn
Figure 8
Figure 9
f=85MHz
2.5
ns
0
ns
(11)
tTPDD
Transmitter Power-Down Delay
Figure 14
tTCCD
Transmitter Clock Input to Clock Output Delay
(TA=25°C and
with VCC=3.3V)
Figure 13
100
ns
2.8
5.5
6.8
ns
Transmitter Output Data Jitter (f=40MHz)(12)
tTPPB0
Transmitter Output Pulse Position of Bit 0
-0.25
0
0.25
ns
tTPPB1
Transmitter Output Pulse Position of Bit 1
a-0.25
a
a+0.25
ns
tTPPB2
Transmitter Output Pulse Position of Bit 2
2a-0.25
2a
2a+0.25
ns
tTPPB3
Transmitter Output Pulse Position of Bit 3
3a-0.25
3a
3a+0.25
ns
tTPPB4
Transmitter Output Pulse Position of Bit 4
4a-0.25
4a
4a+0.25
ns
tTPPB5
Transmitter Output Pulse Position of Bit 5
5a-0.25
5a
5a+0.25
ns
tTPPB6
Transmitter Output Pulse Position of Bit 6
6a-0.25
6a
6a+0.25
ns
Transmitter Output Data Jitter (f=65MHz)
Figure 20
1
a
f 7
(12)
tTPPB0
Transmitter Output Pulse Position of Bit 0
-0.2
0
0.2
ns
tTPPB1
Transmitter Output Pulse Position of Bit 1
a-0.2
a
a+0.2
ns
tTPPB2
Transmitter Output Pulse Position of Bit 2
2a-0.2
2a
2a+0.2
ns
tTPPB3
Transmitter Output Pulse Position of Bit 3
3a-0.2
3a
3a+0.2
ns
tTPPB4
Transmitter Output Pulse Position of Bit 4
4a-0.2
4a
4a+0.2
ns
tTPPB5
Transmitter Output Pulse Position of Bit 5
5a-0.2
5a
5a+0.2
ns
tTPPB6
Transmitter Output Pulse Position of Bit 6
6a-0.2
6a
6a+0.2
ns
Figure 20
1
a
f 7
Continued on the following page…
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
8
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Transmitter AC Electrical Characteristics
Over supply voltage and operating temperature ranges, unless otherwise specified.
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
(12)
Transmitter Output Data Jitter (f=85MHz)
tTPPB0
Transmitter Output Pulse Position of Bit 0
-0.2
0
0.2
ns
tTPPB1
Transmitter Output Pulse Position of Bit 1
a-0.2
a
a+0.2
ns
tTPPB2
Transmitter Output Pulse Position of Bit 2
2a-0.2
2a
2a+0.2
ns
tTPPB3
Transmitter Output Pulse Position of Bit 3
3a-0.2
3a
3a+0.2
ns
tTPPB4
Transmitter Output Pulse Position of Bit 4
4a-0.2
4a
4a+0.2
ns
tTPPB5
Transmitter Output Pulse Position of Bit 5
5a-0.2
5a
5a+0.2
ns
tTPPB6
Transmitter Output Pulse Position of Bit 6
6a-0.2
6a
6a+0.2
ns
f=40MHz
350
370
f=65MHz
210
230
110
150
tJCC
Figure 20
1
a
f 7
FIN3385 Transmitter Clock Out Jitter,
Cycle-to-Cycle, Figure 20
f=85MHz
tTPLLS
(13)
(12)
Transmitter Phase Lock Loop Set Time
Figure 26
10
ps
ms
Notes:
11. Outputs of all transmitters stay in 3-STATE until power reaches 2V. Clock and data output begins to toggle 10ms
after VCC reaches 3.0V and /PwrDn pin is above 1.5V.
12. This output data pulse position works for both transmitters for TTL inputs, except the LVDS output bit mapping
difference (see Figure 18). Figure 20 shows the skew between the first data bit and clock output. A two-bit cycle
delay is guaranteed when the MSB is output from transmitter.
13. This jitter specification is based on the assumption that PLL has a reference clock with cycle-to-cycle input jitter
of less than 2ns.
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
9
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Transmitter AC Electrical Characteristics (Continued)
Typical values are at TA=25°C and with VCC=3.3V. Minimum and maximum values are over supply voltage and
operating temperature ranges unless otherwise specified. Positive current values refer to the current flowing into
device and negative values refer to current flowing out of pins. Voltages are referenced to ground unless otherwise
specified (except VOD and VOD).
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
LVTTL/CMOS DC Characteristics
VIH
Input High Voltage
2.0
VCC
V
VIL
Input Low Voltage
GND
0.8
V
VOH
Output High Voltage
IOH=-0.4mA
VOL
Output Low Voltage
IOL=2mA
0.06
0.30
V
VIK
Input Clamp Voltage
IIK=-18mA
-0.79
-1.50
V
IIN
Input Current
VIN=0V to 4.6V
10
A
IOFF
Input/Output Power-Off
Leakage Current
VCC=0V, All LVTTL Inputs / Outputs
0V to 4.6V
±10
A
IOS
Output Short-Circuit Current
VOUT=0V
-120
m
100
mV
2.7
3.3
-10
-60
V
Receiver LVDS Input Characteristics
VTH
Differential Input Threshold
HIGH
Figure 6, Table 4
VTL
Differential Input Threshold
LOW
Figure 6, Table 4
-100
VICM
Input Common Mode Range
Figure 6, Table 4
0.05
IIN
Input Current
mV
2.35
VIN=2.4V, VCC=3.6V or 0V
±10
VIN=0V, VCC=3.6V or 0V
±10
V
A
Receiver Supply Current
4:28 Receiver Power Supply
Current for Worst-Case Pattern
with Load(14)
ICCWR
ICCPDT
3:21 Receiver Power Supply
Current for Worst-Case Pattern
with Load(14)
Powered-Down Supply Current
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
CL=8pF, Figure 7
32.5MHz
70
40.0MHz
75
66.0MHz
114
85.0MHz
135
32.5MHz
49
60
40.0MHz
53
65
66.0MHz
78
100
85.0MHz
90
115
NA
55
/PwrDn=0.8V (RxOut Stays LOW)
mA
A
www.fairchildsemi.com
10
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Receiver DC Characteristics
Typical values are at TA=25°C and with VCC=3.3V; minimum and maximum are at over supply voltages and operating
temperatures ranges, unless otherwise specified.
Symbol
Parameter
tRCOP
Receiver Clock Output (RxCLKOut) Period
tRCOL
RxCLKOut LOW Time
Condition
Figure 12
Rising Edge Strobe
f=85MHz
tRCOH
RxCLKOut HIGH Time
tRSRC
RxOut Valid Prior to RxCLKOut
tRHRC
RxOut Valid After RxCLKOut
tROLH
Output Rise Time (20% to 80%)
tROHL
Output Fall Time (80% to 20%)
tRCCD
Receiver Clock Input to Clock Output
Delay(15)
TA=25°C, VCC=3.3V,
Figure 24
Figure 17
Min.
Typ.
Max.
11.76
T
50.00
4.0
5.0
6.0
4.5
5.0
6.5
Unit
ns
ns
3.5
ns
3.5
ns
2.0
3.5
1.8
3.5
3.5
5.0
7.5
ns
CL=8pF, Figure 8
ns
tRPPD
Receiver Power-Down Delay
1.0
µs
tRSPB0
Receiver Input Strobe Position of Bit 0
0.49
0.84
1.19
ns
tRSPB1
Receiver Input Strobe Position of Bit 1
2.17
2.52
2.87
ns
tRSPB2
Receiver Input Strobe Position of Bit 2
3.85
4.20
4.55
ns
tRSPB3
Receiver Input Strobe Position of Bit 3
5.53
5.88
6.23
ns
tRSPB4
Receiver Input Strobe Position of Bit 4
7.21
7.56
7.91
ns
tRSPB5
Receiver Input Strobe Position of Bit 5
8.89
9.24
9.59
ns
tRSPB6
Receiver Input Strobe Position of Bit 6
10.57
10.92
11.27
ns
(16)
Figure 21
f=85MHz
tRSKM
RxIN Skew Margin
Figure 21
tRPLLS
Receiver Phase Lock Loop Set Time
Figure 21
tRCOP
Receiver Clock Output (RxCLKOut) Period
Figure 12
tRCOL
RxCLKOut LOW Time
tRCOH
RxCLKOut HIGH Time
tRSRC
RxOUT Valid Prior to RxCLKOut
tRHRC
RxOUT Valid After RxCLKOut
tRCOL
RxCLKOut LOW Time
Figure 12
Rising Edge Strobe
f=40MHz
Figure 12,
Rising Edge Strobe(17)
f=66MHz
tRCOH
RxCLKOut HIGH Time
tRSRC
RxOUT Valid Prior to RxCLKOut
tRHRC
RxOUT Valid After RxCLKOut
tROLH
Output Rise Time (20% to 80%)
tROHL
Output Fall Time (20% to 80%)
tRCCD
Receiver Clock Input to Clock Output
(18)
Delay
Figure 14, TA=25°C
and VCC=3.3v
Figure 17
290
ps
10
ms
15
T
10.0
11.0
50
10.0
12.2
6.5
11.6
6.0
11.6
5.0
6.3
9.0
5.0
7.6
9.0
4.5
7.3
4.0
6.3
ns
5.0
1.8
5.0
3.5
5.0
7.5
ns
1.0
µs
tRPDD
Receiver Power-Down Delay
tRSPB0
Receiver Input Strobe Position of Bit 0
1.00
1.40
2.15
tRSPB1
Receiver Input Strobe Position of Bit 1
4.50
5.00
5.80
tRSPB2
Receiver Input Strobe Position of Bit 2
8.10
8.50
9.15
tRSPB3
Receiver Input Strobe Position of Bit 3
11.6
11.9
12.6
tRSPB4
Receiver Input Strobe Position of Bit 4
15.1
15.6
16.3
tRSPB5
Receiver Input Strobe Position of Bit 5
18.8
19.2
19.9
tRSPB6
Receiver Input Strobe Position of Bit 6
22.5
22.9
23.6
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
ns
2.0
CL=8pF(17), Figure 12
Figure 21, f=40MHz
ns
ns
ns
www.fairchildsemi.com
11
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Receiver AC Characteristics
Typical values are at TA=25°C and with VCC=3.3V; minimum and maximum are at over supply voltages and operating
temperatures ranges, unless otherwise specified.
Symbol
Parameter
Condition
Min.
Typ.
Max.
tRSPB0
Receiver Input Strobe Position of Bit 0
0.7
1.1
1.4
tRSPB1
Receiver Input Strobe Position of Bit 1
2.9
3.3
3.6
tRSPB2
Receiver Input Strobe Position of Bit 2
5.1
5.5
5.8
tRSPB3
Receiver Input Strobe Position of Bit 3
7.3
7.7
8.0
tRSPB4
Receiver Input Strobe Position of Bit 4
9.5
9.9
10.2
tRSPB5
Receiver Input Strobe Position of Bit 5
11.7
12.1
12.4
tRSPB6
Receiver Input Strobe Position of Bit 6
13.9
14.3
14.6
tRSKM
RxIn Skew Margin(19)
tRPLLS
Receiver Phase Lock Loop Set Time
Figure 21, f=66MHz
f=40MHz, Figure 21
490
f=66MHz, Figure 21
400
Figure 15
Unit
ns
ps
10.0
ms
Notes:
14. The power supply current for the receiver can vary with the number of I/O channels.
15. Total channel latency from serializer to deserializer is (t + tTCCD) where t is a clock period.
16. Receiver skew margin is defined as the valid sampling window after considering potential setup/hold time and
minimum/maximum bit position.
17. For the receiver with falling-edge strobe, the definition of setup/hold time is slightly different from the one with
rising-edge strobe. The clock reference point is the time when the clock falling edge passes through 2V. For hold
time tRHRC, the clock reference point is the time when falling edge passes through +0.8V.
18. Total channel latency from serializer to deserializer is (t + tCCD) (2•t + tRCCD) where t is the clock period.
19. Receiver skew margin is defined as the valid sampling window after considering potential setup/hold time and
minimum / maximum bit position.
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
12
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Receiver AC Characteristics
Figure 5. Differential LVDS Output DC Test Circuit
Notes:
A: For all input pulses, tR or tF<=1ns.
B: CL includes all probe and jig capacitance.
Figure 6. Differential Receiver Voltage Definitions, Propagation Delay, and Transition Time Test Circuit
Table 4. Receiver Minimum and Maximum Input Threshold Test Voltages
Applied Voltages (V)
Resulting Differential
Input Voltage (mV)
Resulting Common
Mode Input Voltage (V)
VID
VICM
VIA
VIB
1.25
1.15
100
1.20
1.15
1.25
-100
1.20
2.40
2.30
100
2.35
2.30
2.40
-100
2.35
0.10
0
100
0.05
0
0.10
-100
0.05
1.50
0.90
600
1.20
0.90
1.50
-600
1.20
2.40
1.80
600
2.10
1.80
2.40
-600
2.10
0.60
0
600
0.30
0
0.60
-600
0.30
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
13
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Test Circuits
Figure 7. Worst-Case Test Pattern
Note:
20. The worst-case test pattern produces a maximum toggling of digital circuits, LVDS I/O, and LVTTL/CMOS I/O.
Depending on the valid strobe edge of the transmitter, the TxCLKIn can be rising or falling edge data strobe.
Figure 8. Transmitter LVDS Output Load and Transition Times
Figure 9. Transmitter Setup/Hold and HIGH/LOW Times (Rising-Edge Strobe)
Figure 10. Transmitter Input Clock Transition Time
Figure 11. Transmitter Outputs Channel-to-Channel Skew
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
14
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
AC Loadings and Waveforms
Figure 12. Receiver Setup/Hold and HIGH/LOW Times
Note:
21. For the receiver with falling-edge strobe, the definition of setup/hold time is slightly different from the one with
rising-edge strobe. The clock reference point is the time when the clock falling edge passes through 2V. For hold
time tRHRC, the clock reference point is the time when falling edge passes through +0.8V.
Figure 13. Transmitter Clock-In to Clock-Out Delay (Rising-Edge Strobe)
Figure 14. Receiver Clock-In to Clock-Out Delay (Falling-Edge Strobe)
Figure 15. Receiver Phase-Lock-Loop Set Time
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
15
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
AC Loadings and Waveforms (Continued)
Figure 16. Transmitter Power-Down Delay
Figure 17. Receiver Power-Down Delay
Figure 18. 28 Parallel LVTTL Inputs Mapped to Four Serial LVDS Outputs
Note:
22. The information in this diagram shows the difference between clock out and the first data bit. A 2-bit cycle delay
is guaranteed when the MSB is output from the transmitter.
Figure 19. 21 Parallel LVTTL Inputs Mapped to Three Serial Outputs
Note:
23. This output date pulse position works for both transmitters with 21 TTL inputs, except the LVDS output bit
mapping difference. Two-bit cycle delay is guaranteed with the MSB is output from transmitter.
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
16
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
AC Loadings and Waveforms (Continued)
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
AC Loadings and Waveforms (Continued)
Figure 20. Transmitter Output Pulse Bit Position
Figure 21. Receiver Input Bit Position
Figure 22. Receiver LVDS Input Skew Margin
Note:
24. tRSKM is the budget for the cable skew and source clock skew plus Inter-Symbol Interference (ISI).
The minimum and maximum pulse position values are based on the bit position of each of the seven bits within
the LVDS data stream across PVT (Process, Voltage Supply, and Temperature).
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
17
Figure 23. Transmitter Clock Out Jitter Measurement Setup
Note:
25. Test setup considers no requirement for separation of RMS and deterministic jitter. Other hardware setups,
such as Wavecrest boxes, can be used if no M1 software is available, but the test methodology in Figure 24
should be followed.
Figure 24. Timing Diagram of Transmitter Clock Input with Jitter
Note:
26. This jitter pattern is used to test the jitter response (clock out) of the device over the power supply range with
worst jitter ±3ns (cycle-to-cycle) clock input. The specific test methodology is as follows:
27. Switching input data TxIn0 to TxIn20 at 0.5MHz and the input clock is shifted to left -3ns and to the right +3ns
when data is HIGH.
28. The ±3ns cycle-to-cycle input jitter is the static phase error between the two clock sources. Jumping between two
clock sources to simulate the worst-case of clock-edge jump (3ns) from graphical controllers. Cycle-to-cycle jitter
at TxCLKOut pin should be measured cross VCC range with 100mV noise (VCC noise frequency <2MHz).
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
18
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
AC Loadings and Waveforms (Continued)
Figure 25. “16-Grayscale” Test Pattern
Note:
29. The 16-grayscale test pattern tests device power consumption for a “typical” LCD display pattern. The test
pattern approximates signal switching needed to produce groups of 16 vertical strips across the display.
Figure 26. Transmitter Phase-Lock-Loop Time
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
19
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
AC Loadings and Waveforms (Continued)
A
56
51
1
6
34
29
23
28
6.15
7.6
9.125
B
8.10
1.45
4.05
0.2 C B A
0.30
0.50
0.1 C
-C-
0.50
0.10
A B
C
0.25
MTD56REV3
Figure 27. 56-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153,6.1mm Wide
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or
obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the
warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
20
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
Physical Dimensions
FIN3385 / FIN3386 — Low-Voltage, 28-Bit Flat Panel Display Link Serializer / Deserializer
© 2003 Fairchild Semiconductor Corporation
FIN3385 / FIN3386 • Rev. 1.0.6
www.fairchildsemi.com
21