74LCX244 LOW VOLTAGE CMOS OCTAL BUS BUFFER (3-STATE) WITH 5V TOLERANT INPUTS AND OUTPUTS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 5V TOLERANT INPUTS AND OUTPUTS HIGH SPEED : tPD = 6.5 ns (MAX.) at VCC = 3V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) at VCC = 3V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2.0V to 3.6V (1.5V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 244 LATCH-UP PERFORMANCE EXCEEDS 500mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (MIL STD 883 method 3015); MM > 200V DESCRIPTION The 74LCX244 is a low voltage CMOS OCTAL BUS BUFFER (NON-INVERTED) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power SOP TSSOP ORDER CODES PACKAGE TUBE T&R SOP TSSOP 74LCX244M 74LCX244MTR 74LCX244TTR and high speed 3.3V applications; it can be interfaced to 5V signal environment for both inputs and outputs. It has same speed performance at 3.3V than 5V AC/ACT family, combined with a lower power consumption. This device is designed to be used with 3 state memory address drivers, etc. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS March 2002 1/9 74LCX244 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION TRUTH TABLE PIN No SYMBOL 1 2, 4, 6, 8 9, 7, 5, 3 11, 13, 15, 17 18, 16, 14, 12 19 10 20 1G 1A1 to 1A4 2Y1 to 2Y4 2A1 to 2A4 Output Enable Input Data Inputs Data Outputs Data Inputs 1Y1 to 1Y4 Data Outputs 2G GND V CC NAME AND FUNCTION INPUT OUTPUT G An Yn L L H L H X L H Z X : Don’t Care Z : High Impedance Output Enable Input Ground (0V) Positive Supply Voltage ABSOLUTE MAXIMUM RATINGS Symbol V CC Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage (OFF State) -0.5 to +7.0 V VO DC Output Voltage (High or Low State) (note 1) IIK DC Input Diode Current IOK IO -0.5 to VCC + 0.5 V - 50 mA DC Output Diode Current (note 2) - 50 mA DC Output Current ± 50 mA ICC DC Supply Current per Supply Pin ± 100 mA IGND DC Ground Current per Supply Pin ± 100 mA Tstg Storage Temperature -65 to +150 °C TL Lead Temperature (10 sec) 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) IO absolute maximum rating must be observed 2) VO < GND 2/9 74LCX244 RECOMMENDED OPERATING CONDITIONS Symbol V CC Parameter Supply Voltage (note 1) Value Unit 2.0 to 3.6 V 0 to 5.5 V VI Input Voltage VO Output Voltage (OFF State) 0 to 5.5 V VO Output Voltage (High or Low State) 0 to VCC V ± 24 mA ± 12 mA IOH, IOL High or Low Level Output Current (V CC = 3.0 to 3.6V) IOH, IOL High or Low Level Output Current (V CC = 2.7V) Operating Temperature Top dt/dv Input Rise and Fall Time (note 2) -55 to 125 °C 0 to 10 ns/V 1) Truth Table guaranteed: 1.5V to 3.6V 2) VIN from 0.8V to 2V at VCC = 3.0V DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Ioff IOZ ICC ∆ICC Input Leakage Current Power Off Leakage Current High Impedance Output Leakage Current Quiescent Supply Current ICC incr. per Input Min. Max. 2.0 -55 to 125 °C Min. Unit Max. 2.0 V 2.7 to 3.6 0.8 0.8 2.7 to 3.6 I O=-100 µA VCC-0.2 VCC-0.2 2.7 IO=-12 mA 2.2 2.2 IO=-18 mA 2.4 2.4 IO=-24 mA 2.2 2.2 V V 2.7 to 3.6 IO=100 µA 0.2 0.2 2.7 IO=12 mA 0.4 0.4 IO=16 mA 0.4 0.4 IO=24 mA 0.55 0.55 2.7 to 3.6 VI = 0 to 5.5V ±5 ±5 µA 0 V I or VO = 5.5V 10 10 µA 2.7 to 3.6 V I = VIH or VIL VO = 0 to VCC ±5 ±5 µA VI = VCC or GND 10 10 ± 10 ± 10 500 500 3.0 II -40 to 85 °C VCC (V) 3.0 VOL Value 2.7 to 3.6 VI or VO= 3.6 to 5.5V VIH = VCC - 0.6V 2.7 to 3.6 V µA µA 3/9 74LCX244 DYNAMIC SWITCHING CHARACTERISTICS Test Condition Symbol VOLP V OLV Parameter Value TA = 25 °C VCC (V) Dynamic Low Level Quiet Output (note 1) 3.3 Min. Typ. Unit Max. 0.8 CL = 50pF VIL = 0V, V IH = 3.3V V -0.8 1) Number of outputs defined as ”n”. Measured with ”n-1” outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. AC ELECTRICAL CHARACTERISTICS Test Conditi on Symbol Parameter tPLH tPHL Propagation Delay Time tPZL tPZH Output Enable Time tPLZ tPHZ Output Disable Time tOSLH tOSHL Output To Output Skew Time (note1, 2) VCC (V) 2.7 3.0 to 3.6 2.7 3.0 to 3.6 2.7 3.0 to 3.6 3.0 to 3.6 Value CL (pF) RL (Ω) ts = t r (ns) 50 500 2.5 50 500 2.5 50 500 2.5 50 500 2.5 -40 to 85 °C -55 to 125 °C Min. Max. Min. Max. 1.5 1.5 1.5 1.5 1.5 1.5 7.5 6.5 9.0 8.0 8.0 7.0 1.0 1.5 1.5 1.5 1.5 1.5 1.5 8.2 7.1 10.5 9.2 9.2 7.7 1.0 Unit ns ns ns ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|) 2) Parameter guaranteed by design CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter Value TA = 25 °C VCC (V) Min. Typ. Unit Max. Input Capacitance 3.3 VIN = 0 to VCC 6 pF C OUT Output Capacitance 3.3 VIN = 0 to VCC 10 pF CPD Power Dissipation Capacitance (note 1) 3.3 fIN = 10MHz V IN = 0 or VCC 34 CIN pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per circuit) 4/9 74LCX244 TEST CIRCUIT TEST tPLH, tPHL SWITCH Open tPZL, tPLZ 6V tPZH, tPHZ GND C L = 50 pF or equivalent (includes jig and probe capacitance) R L = R1 = 500Ω or equivalent R T = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1 : PROPAGATION DELAYS (f=1MHz; 50% duty cycle) 5/9 74LCX244 WAVEFORM 2 : OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 6/9 74LCX244 SO-20 MECHANICAL DATA mm. inch DIM. MIN. TYP A a1 MAX. MIN. TYP. 2.65 0.1 0.104 0.2 a2 MAX. 0.004 0.008 2.45 0.096 b 0.35 0.49 0.014 0.019 b1 0.23 0.32 0.009 0.012 C 0.5 0.020 c1 45° (typ.) D 12.60 13.00 0.496 0.512 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 F 7.40 7.60 0.291 0.300 L 0.50 1.27 0.020 0.050 M S 0.75 0.029 8° (max.) PO13L 7/9 74LCX244 TSSOP20 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. A MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 6.4 6.5 6.6 0.252 0.256 0.260 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.0256 BSC 0.60 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b K e L E c D E1 PIN 1 IDENTIFICATION 1 0087225C 8/9 74LCX244 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringe ment of patents or other righ ts of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this pub lication are subject to change without notice. Thi s pub lication supersedes and replaces all information previously supplied. STMicroelectronics prod ucts are not authori zed for use as critical components in life suppo rt devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2000 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Swit zerland - United Kingdom http://w ww.st.com 9/9