L5170 OCTAL LINE DRIVER ADVANCE DATA OCTAL LINE DRIVER FOR: – EIA STD: RS232D; RS423A – CCIT: V.10; V.28 NO EXTERNAL COMPONENTS VERY LONG TRANSMISSION LINE (5000ft) 50V EOS OUTPUT PROTECTION DIP28 DESCRIPTION L5170 is an octal line driver unit in DIP28 and PLCC28 packages intended for use in the EIA std RS232D, RS423A and CCITT V.10 and V.28 applications. With no external components L5170 is able to drive a line up to 5000ft assuming the line capacitance is 35pF per ft and the capacitance of the filter connectors/protection components add up to PLCC28 ORDERING NUMBERS: L5170A L5170D the total capacitance load. The drivers typically run in short circuit current mode whenever the cable attached is over 500ft. BLOCK DIAGRAM March 1993 1/9 This is advanced information on a new product now in development or undergoing evaluation. Details are subject to change without notice. L5170 PIN CONNECTIONS (Top views) DIP28 PLCC28 ABSOLUTE MAXIMUM RATINGS Symbol Parameter VCC Supply Voltage VEE Supply Voltage Vi Input Voltage (Enable Data) VO Output Voltage Value Unit +15 V – 15 V – 1.5 to 7 V ±6 V IO Output Current (**) ±150 mA SR Minimum Slew Resistor (***) 1.5 1KΩ Ptot Power Dissipation at Tamb = 70°C (PLCC28) (*) (DIP28) (*) 1.2 1.3 W W Top Operating Free Air Temperature Range 0 to +70 °C Tstg Storage Temperature Range -65 to 150 °C Notes: (*) Mounted on board with minimized dissipating copper area. (**) Minimum Current per driver. Do not exceed maximum power dissipation if more than one input is on. (***) Minimum value of the resistor used to set the slew rate. THERMAL DATA Symbol R th j-amb 2/9 Description Thermal Resistance Junction-ambient (*) Max. PLCC28 DIP28 Unit 67 62 °C/W L5170 AC ELECTRICAL CHARACTERISTICS (VCC = 9 to 11V; VEE = – 9 to – 11V T amb =0 to 70°C, unless otherwise specified Symbol VOH VOL Parameter High Level Output Voltage Low Level Output Voltage VOl Output Voltage Balance VIH High Level Input Voltage Test Condition Vin = 0.8V R L = inf R L = 3KΩ R L = 450Ω (see note 1) Vin = 2.4V R L = inf R L = 3KΩ R L = 450Ω (see note 1) Min. Max. Unit 5 5 4.5 6 6 6 V V V –6 –6 –6 –5 –5 – 4.5 V V V 0.4 V |VCC| = |VEE|; RL = 450Ω Typ. 2 V VIL Low Level Input Voltage VIK Input Clamp Voltage IIN = – 15mA 0.8 IIH High Level Input Current VIN = 2.4V IIL Low Level Input Current VIN = 0.4V ICC Positive Supply Current VIN = 2.4V; RS = 2KΩ; RL = 3KΩ C L = 2.5nF; (See note 2) 30 mA ICC1 Positive Supply Current VIN = 0.4V; RS = 2KΩ; RL = 3KΩ C L = 2.5nF; (See note 2) 40 mA IEE Negative Supply Current VIN = 2.4V; RS = 2KΩ; RL = 3KΩ C L = 2.5nF; (See note 2) – 30 mA IEE1 Negative Supply Current VIN = 0.4V; RS = 2KΩ; RL = 3KΩ C L = 2.5nF; (See note 2) – 40 mA Ish Output Short Circuit Current VO = 0V; VIN = 2.4V; (see fig.1) 25 100 – 1.5 V V 40 µA µA – 400 mA Isl Output Short Circuit Current VO = 0V; VIN = 2.4V; (see fig.1) – 100 – 25 mA Ibal Output Current Balance Ish/Isl = Ibal 0.625 1.6 mA/mA Ix Output Leakage Current See fig.2,3 and note 3 VO = 6V VO = – 6V 70 – 70 µA µA 2.7 µs tr Rise time (see note 4 and 5; see figure 4A) R L = 450Ω; CL = 50pF R slew = 5.34KΩ ±1% 2 trc1 R L = 450Ω; CL = 0.01µF R slew = 10KΩ ±1% 10 µs trc2 R L = 450Ω; CL = 0.1µF R slew = 10KΩ ±1% 50 µs trc3 R L = 450Ω; CL = 2.5nF R slew = 2KΩ ±1% 0.65 1.2 µs trc4 R L = 450Ω; CL = 2.5nF R slew = 10KΩ ±1% 3.25 6 µs R L = 450Ω; CL = 50pF R slew = 5.34KΩ ±1% 2 2.7 µs tf Fall time (see note 4 and 5; see figure 4A) tfc1 R L = 450Ω; CL = 0.01µF R slew = 10KΩ ±1% 10 µs tfc2 R L = 450Ω; CL = 0.1µF R slew = 10KΩ ±1% 50 µs tfc3 R L = 450Ω; CL = 2.5nF R slew = 2KΩ ±1% 0.65 1.2 µs tfc4 R L = 450Ω; CL = 2.5nF R slew = 10KΩ ±1% 3.25 6 µs Note 1: The Output under load must not drop below 90% of the open circuit drive level. Note 2: This represents the static condition only. Applications can see 130mA normal current draw for clock and data lines with up to 500mA transients when all lines are transitioning at the same time. Over 500ft of cable slew rate is governed by the drivers ability to sink current. The currents are rougly equivalent to the short circuit current. 3/9 L5170 AC ELECTRICAL CHARACTERISTICS (continued) Symbol tlz tnz Parameter Output Enable to Output (see figure 4B) Test Condition Min. R L = 450Ω; CL = 50pF R slew = 10KΩ tzl Propagation (see figure 4C) tph1 R L = 450Ω; CL = 50pF R slew = 2KΩ Max. Unit 5 µs 5 µs 150 µs 150 µs 0.3 0.9 µs 0.3 0.9 µs tzh tplh Typ. LINE TRANSIENT IMMUNITY (Considering the following cases: Powered ON, Powered OFF-Low impedance power supply and Powered OFF-High impedance supply). ESD Elettrostatic Discharge Tested per MIL-STD-883 (see note 6) 2 KV EOS Electrical Overstress Transient pulse both polarities for 100µs (see note 7) 50 V Note 3: The output leakage is measured under the following conditions: a) The Driver tristated b) Power supply OFF, and the power pins shorted to Ground c) Power supply OFF. Impedances between power pins open and power pins shorted to Ground. Note 4: The output waveform should not show any signs of oscillations under any load variation between o.1VVss and 0.9Vss. The oscillation allowed when VSS < 0.1VSS and Vss >0.9Vss shall be 10% of Vss. Note 5: tfc1 thru trc4 shall be within ±20% of trc1 thru trc4 respectively. Note 6: All pins are required to withstand parameter. Note 7: Output pins are required to withstand fig.5 without any degradation to the circuit. TEST CIRCUIT 4/9 L5170 Figure 1: Output Leakage Test Circuit Figure 2: Output Voltage Rise Time Figure 3: EOS Requirements 5/9 L5170 Figure 4: Waveforms 6/9 L5170 DIP28 PACKAGE MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. a1 0.63 0.025 b 0.45 0.018 b1 0.23 b2 0.31 1.27 D E 0.009 0.012 0.050 37.34 15.2 16.68 1.470 0.598 0.657 e 2.54 0.100 e3 33.02 1.300 F MAX. 14.1 0.555 I 4.445 0.175 L 3.3 0.130 7/9 L5170 PLCC28 PACKAGE MECHANICAL DATA mm DIM. MIN. TYP. MAX. MIN. TYP. MAX. A 12.32 12.57 0.485 0.495 B 11.43 11.58 0.450 0.456 D 4.2 4.57 0.165 0.180 D1 2.29 3.04 0.090 0.120 D2 0.51 E 9.91 0.020 10.92 0.390 0.430 e 1.27 0.050 e3 7.62 0.300 F 0.46 0.018 F1 0.71 0.028 G 8/9 inch 0.101 0.004 M 1.24 0.049 M1 1.143 0.045 L5170 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. 1995 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands - Singapore Spain - Sweden - Switzerland - Taiwan - Thaliand - United Kingdom - U.S.A. 9/9