M54HC137 M74HC137 3 TO 8 LINE DECODER/LATCH (INVERTING) . . . . . . . . HIGH SPEED tPD = 11 ns (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 4 µA (MAX.) AT TA = 25 °C HIGH NOISE IMMUNITY VNIH = VNIL = 28 % VCC (MIN.) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2 V TO 6 V PIN AND FUNCTION COMPATIBLE WITH 54/74LS137 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HC137F1R M74HC137M1R M74HC137B1R M74HC137C1R DESCRIPTION The M54/74HC137 is a high speed CMOS 3 TO 8LINE DECODER/LATCH (INVERTING) fabricated in silicon gate C2MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low power consumption. This device is a 3 to 8line decoder withlatches on thethree address inputs. When GL goes from low tohigh, theaddress present at theselect inputs (A, B and C) is stored in the latches. As long as GL remains high no address changes will be recognized. Output enable pins G1 and G2, control the state of the outputs independently of the select or latch-enable inputs. All the outputs are high unless G1 is high and G2 is low. The HC137 is ideally suited for the implementation of glitch-free decoders in stored-address applications in bus oriented systems. All inputs are equipped withprotection circuits against staticdischarge and transient excess voltage. PIN CONNECTIONS (top view) INPUT AND OUTPUT EQUIVALENT CIRCUIT NC = No Internal Connection February 1993 1/11 M54/M74HC137 TRUTH TABLE INPUTS OUTPUTS GL ENABLE G1 C SELECT B G2 X X H A Y0 Y1 Y2 Y3 Y4 Y5 Y6 X X X H H H H H H H X L L H H X L X L X L X L H L H H H H H H H H H H H H H H L L L H L L L H H L H H H H H H H H L L L L H H L H H H H H L H H L H H H H H H H H L H L H L L H H H H L H H H L L H H L L H H L H H L H H H H H H H H H H L H H L H H L H H H L L H X H X H X H LOGIC DIAGRAM 2/11 Y7 H H H H H H L Outputs corresponding to stored address L: all others H M54/M74HC137 PIN DESCRIPTION PIN No SYMBOL 1, 2, 3 4 A to C GL Data Inputs Latch Enable Input (Active LOW) NAME AND FUNCTION 5 G2 Data Enable Input (Active LOW) 6 15, 14, 13, 12, 11, 10, 9, 7 G1 Y0 to Y7 Data Enable Input (Active HIGH) Multiplexer Outputs 8 GND Ground (0V) 16 VCC Positive Supply Voltage IEC LOGIC SYMBOLS ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V V DC Input Diode Current ± 20 mA DC Output Diode Current DC Output Source Sink Current Per Output Pin ± 20 ± 25 mA mA VCC Supply Voltage VI VO DC Input Voltage DC Output Voltage IIK IOK IO ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) ± 50 mA 500 (*) mW -65 to +150 o C 300 o C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC 3/11 M54/M74HC137 RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC VI Supply Voltage Input Voltage VO Output Voltage Top Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time tr, tf Value Unit 2 to 6 0 to VCC V V 0 to VCC V o -55 to +125 -40 to +85 0 to 1000 VCC = 2 V VCC = 4.5 V 0 to 500 VCC = 6 V 0 to 400 C C ns o DC SPECIFICATIONS Test Conditions Symbol VIH V IL V OH VOL Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage VCC (V) 2.0 Min. 1.5 4.5 3.15 6.0 2.0 4.2 6.0 2.0 ICC 4/11 Quiescent Supply Current Max. -40 to 85 oC -55 to 125 oC 74HC 54HC Min. 1.5 Max. 3.15 Min. 1.5 4.2 4.2 0.5 0.5 1.35 1.35 1.35 1.8 2.0 1.9 1.9 4.5 4.4 4.4 6.0 4.5 5.9 4.18 6.0 4.31 5.9 4.13 5.9 4.10 6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60 6.0 6.0 V 1.8 1.9 4.4 2.0 4.5 V 0.5 1.8 Unit Max. 3.15 VI = IO=-20 µA VIH or V IL IO=-4.0 mA 4.5 4.5 6.0 Input Leakage Current Typ. 4.5 6.0 II Value TA = 25 oC 54HC and 74HC V 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.1 0.0 0.1 0.1 0.1 0.17 0.18 0.26 0.26 0.33 0.33 0.40 0.40 VI = VCC or GND ±0.1 ±1 ±1 µA VI = VCC or GND 2 20 40 µA VI = IO= 20 µA VIH or V IL IO= 4.0 mA IO= 5.2 mA V M54/M74HC137 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (G1 - Y) tPLH tPHL Propagation Delay Time (G2 - Y) tPLH tPHL Propagation Delay Time (GL - Y) tPLH tPHL Propagation Delay Time (A, B, C - Y) tW(L) Minimum Pulse Width (GL) ts th CIN CPD (*) Minimum Set-up Time (A, B, C - GL) Minimum Hold Time (A, B, C - GL) Input Capacitance Power Dissipation Capacitance Value o VCC (V) TA = 25 C 54HC and 74HC Min. Typ. Max. -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 2.0 30 75 95 110 4.5 6.0 8 7 15 13 19 16 22 19 2.0 45 115 145 175 4.5 14 23 29 35 6.0 12 20 25 30 2.0 50 115 145 175 4.5 6.0 15 13 23 20 29 25 35 30 2.0 70 170 215 250 4.5 6.0 22 19 34 29 43 37 50 43 2.0 70 165 205 110 4.5 6.0 21 18 33 28 41 35 22 19 2.0 12 50 65 75 4.5 6.0 3 3 10 9 13 11 15 13 2.0 8 50 60 75 4.5 6.0 2 2 10 9 12 10 15 13 5 5 5 5 5 5 2.0 4.5 6.0 5 55 5 5 5 10 10 10 Unit ns ns ns ns ns ns ns ns pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC 5/11 M54/M74HC137 TEST CIRCUIT ICC (Opr.) INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST. TYPICAL APPLICATION 6/11 M54/M74HC137 Plastic DIP16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 7/11 M54/M74HC137 Ceramic DIP16/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7 0.276 D E 3.3 0.130 0.38 e3 0.015 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053D 8/11 M54/M74HC137 SO16 (Narrow) MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) P013H 9/11 M54/M74HC137 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 10/11 M54/M74HC137 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 11/11