STMICROELECTRONICS M74HC280B1R

M54HC280
M74HC280
9 BIT PARITY GENERATOR
.
.
.
.
.
.
.
.
HIGH SPEED
tPD = 22 ns (TYP.) at VCC = 5 V
LOW POWER DISSIPATION
ICC = 4 µA (MAX.) at TA = 25 °C 6 V
HIGH NOISE IMMUNITY
VNIH = VNIL = 28 % VCC (MIN.)
OUTPUT DRIVE CAPABILITY
10 LSTTL LOADS
SYMMETRICAL OUTPUT IMPEDANCE
IOH = IOL = 4 mA (MIN.)
BALANCED PROPAGATION DELAYS
tPLH = tPHL
WIDE OPERATING VOLTAGE RANGE
VCC (OPR) = 2 V to 6 V
PIN AND FUNCTION COMPATIBLE WITH
54/74LS280
B1R
(Plastic Package)
F1R
(Ceramic Package)
M1R
(Micro Package)
C1R
(Chip Carrier)
ORDER CODES :
M54HC280F1R
M74HC280M1R
M74HC280B1R
M74HC280C1R
PIN CONNECTIONS (top view)
DESCRIPTION
The M54/74HC280 is a high speed CMOS 9-BIT
PARITY GENERATOR fabricated in silicon gate
C2MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low
consumption.
It is composed of nine data inputs (A to I) and
odd/even parity outputs (Σ ODD and Σ EVEN). The
nine data inputs control the output conditions. When
the number of high level inputs is odd, ΣODD output
is kept high and ΣEVEN output low. Conversely,
when the number is even , ΣEVEN output is kept
high and ΣODD low.
This IC generates either odd or even parity making
it flexible application.
The word-length capability is easily expanded by
cascading.
All inputs are equipped with protection circuits
against static discharge and transient excess voltage.
October 1992
NC =
No Internal
Connection
1/10
M54/M74HC280
INPUT AND OUTPUT EQUIVALENT CIRCUIT
TRUTH TABLE
NUMBER OF INPUTS A THRU I THAT ARE HIGH
0, 2, 4, 6, 8
1, 3, 5, 7, 9
LOGIC DIAGRAM
2/10
OUTPUT
Σ EVEN
Σ ODD
H
L
L
H
M54/M74HC280
PIN DESCRIPTION
IEC LOGIC SYMBOL
PIN No
SYMBOL
NAME AND FUNCTION
5, 6
Σ EVEN,
Σ ODD
A to I
Parity Outputs
NC
No Connection
8, 9, 10,
11, 12, 13,
1, 2, 4
3
Data Inputs
7
GND
Ground (0V)
14
V CC
Positive Supply Voltage
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
Parameter
Supply Voltage
Value
-0.5 to +7
Unit
V
VI
DC Input Voltage
-0.5 to VCC + 0.5
V
VO
IIK
DC Output Voltage
DC Input Diode Current
-0.5 to VCC + 0.5
± 20
V
mA
IOK
DC Output Diode Current
± 20
mA
DC Output Source Sink Current Per Output Pin
DC VCC or Ground Current
± 25
± 50
mA
mA
500 (*)
mW
IO
ICC or IGND
PD
Power Dissipation
Tstg
TL
Storage Temperature
Lead Temperature (10 sec)
-65 to +150
300
o
o
C
C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Parameter
Supply Voltage
VI
Input Voltage
VO
Top
Output Voltage
Operating Temperature: M54HC Series
M74HC Series
tr, tf
Input Rise and Fall Time
Value
2 to 6
Unit
V
0 to VCC
V
0 to VCC
-55 to +125
-40 to +85
VCC = 2 V
0 to 1000
VCC = 4.5 V
VCC = 6 V
0 to 500
0 to 400
V
C
o
C
o
ns
3/10
M54/M74HC280
DC SPECIFICATIONS
Test Conditions
Symbol
VIH
V IL
Parameter
High Level Input
Voltage
Low Level Input
Voltage
Value
VCC
(V)
TA = 25 oC
54HC and 74HC
Min. Typ. Max.
2.0
1.5
1.5
1.5
4.5
6.0
3.15
4.2
3.15
4.2
3.15
4.2
High Level
Output Voltage
0.5
0.5
0.5
4.5
1.35
1.35
1.35
2.0
4.5
6.0
4.5
VOL
Low Level Output
Voltage
6.0
2.0
4.5
6.0
4.5
6.0
II
ICC
4/10
Input Leakage
Current
Quiescent Supply
Current
6.0
6.0
1.8
1.8
Unit
V
2.0
6.0
V OH
-40 to 85 oC -55 to 125 oC
74HC
54HC
Min. Max. Min. Max.
V
1.8
1.9
2.0
1.9
1.9
VI =
IO=-20 µA
VIH
or
V IL IO=-4.0 mA
4.4
5.9
4.5
6.0
4.4
5.9
4.4
5.9
4.18
4.31
4.13
4.10
IO=-5.2 mA
5.68
5.8
0.0
5.63
5.60
V
VI =
IO= 20 µA
VIH
or
V IL IO= 4.0 mA
0.1
0.1
0.1
0.0
0.1
0.1
0.1
0.0
0.17
0.1
0.26
0.1
0.33
0.1
0.40
IO= 5.2 mA
0.18
V
0.26
0.33
0.40
VI = VCC or GND
±0.1
±1
±1
µA
VI = VCC or GND
4
40
80
µA
M54/M74HC280
AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)
Test Conditions
o
TA = 25 C
54HC and 74HC
Value
-40 to 85 oC -55 to 125 oC
74HC
54HC
Symbol
Parameter
VCC
(V)
tTLH
tTHL
Output Transition
Time
2.0
4.5
Typ.
30
8
Max.
75
15
Propagation
Delay Time
(CLOCK - Q)
6.0
2.0
4.5
6.0
7
80
26
22
13
200
40
34
16
250
50
43
19
290
58
49
ns
5
61
10
10
10
pF
tPLH
tPHL
CIN
CPD (*)
Input Capacitance
Power Dissipation
Capacitance
Min.
Min.
Max.
95
19
Min.
Max.
110
22
Unit
ns
pF
(*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC
SWITCHING CHARACTERISTICS TEST
WAVEFORM
TEST CIRCUIT ICC (Opr.)
INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF
SWITCHING CHARACTERISTICSTEST.
5/10
M54/M74HC280
Plastic DIP14 MECHANICAL DATA
mm
DIM.
MIN.
a1
0.51
B
1.39
TYP.
inch
MAX.
MIN.
TYP.
MAX.
0.020
1.65
0.055
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
15.24
0.600
F
7.1
0.280
I
5.1
0.201
L
Z
3.3
1.27
0.130
2.54
0.050
0.100
P001A
6/10
M54/M74HC280
Ceramic DIP14/1 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
20
0.787
B
7.0
0.276
D
E
3.3
0.130
0.38
e3
0.015
15.24
0.600
F
2.29
2.79
0.090
0.110
G
0.4
0.55
0.016
0.022
H
1.17
1.52
0.046
0.060
L
0.22
0.31
0.009
0.012
M
1.52
2.54
0.060
0.100
N
P
Q
10.3
7.8
8.05
5.08
0.406
0.307
0.317
0.200
P053C
7/10
M54/M74HC280
SO14 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
A
a1
inch
MAX.
MIN.
TYP.
1.75
0.1
0.068
0.2
a2
MAX.
0.003
0.007
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45° (typ.)
D
8.55
E
5.8
8.75
0.336
6.2
0.228
0.344
0.244
e
1.27
0.050
e3
7.62
0.300
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
S
0.68
0.026
8° (max.)
P013G
8/10
M54/M74HC280
PLCC20 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
9.78
10.03
0.385
0.395
B
8.89
9.04
0.350
0.356
D
4.2
4.57
0.165
0.180
d1
2.54
0.100
d2
0.56
0.022
E
7.37
8.38
0.290
0.330
e
1.27
0.050
e3
5.08
0.200
F
0.38
0.015
G
0.101
0.004
M
1.27
0.050
M1
1.14
0.045
P027A
9/10
M54/M74HC280
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.
 1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
10/10