M74HCT132 QUAD 2-INPUT SCHMITT NAND GATE PRELIMINARY DATA ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 20 ns (TYP.) at VCC = 4.5V LOW POWER DISSIPATION: ICC = 1 µA (MAX.) at TA = 25 oC OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS HIGH NOISE IMMUNITY VH (TYP.) = 0.71V AT VCC = 4.5V SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 132 DESCRIPTION The M74HCT132 is a high speed CMOS QUAD 2-INPUT SCHMITT NAND GATE fabricated in silicon gate C2MOS tecnology. It has the same high speed performance of LSTTL combined with true COMS low power consumption. Pin B1R M1R (Plastic Package) (Micro Package) ORDER CODES : M74HCT132B1R M74HCT132M1R configuration and function are identical to those of the M74HCT00. The hysteresis characteristics (around 15% VCC) of all inputs allow slowly charging input signals to be transformed into sharply defined jitter-free output signals. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS June 1998 1/7 74HCT132 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1, 4, 9, 12 1A to 4A NAME AND F UNCTIO N Data Inputs 2, 5, 10, 13 1B to 4B Data Inputs 3, 6, 8, 11 1Y to 4Y Data Outputs 7 GND Ground (0V) 14 VCC Positive Supply Voltage TRUTH TABLE A B Y L L H L H H H L H H H L ABSOLUTE MAXIMUM RATINGS Symbol Parameter Unit -0.5 to +7.0 V VI DC Input Voltage -0.5 to VCC + 0.5 V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ± 50 mA 500 (*) mW VCC Supply Voltage Value ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) -65 to +150 o C 300 o C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. (*) 500 mW: ≅ 65 oC derate 300 mW by 10 mW/oC: 65 oC to 80 oC RECOMMENDED OPERATING CONDITIONS Symbol Value Un it Supply Voltage 4.5 to 5.5 V VI Input Voltage 0 to VCC V VO Output Voltage Top Operating Temperature VCC 2/7 Parameter 0 to VCC -40 to +85 V o C 74HCT132 DC SPECIFICATIONS Symbol Vt+ VtVh VOH VOL II ICC Parameter Test Co nditio ns Value T A = 25 oC Unit -40 to 85 o C V CC (V) Min. Typ . Max. Min. Max. High Level Threshold Voltage 4.5 1.2 1.55 1.9 1.2 1.9 5.5 1.4 1.75 2.1 1.4 2.1 Low Level Threshold Voltage 4.5 0.5 0.85 1.2 0.5 1.2 5.5 0.6 1.1 1.4 0.6 1.4 Hysteresis Voltage 4.5 0.4 0.7 1.4 0.4 1.4 5.5 0.4 0.7 1.5 0.4 1.5 High Level Output Voltage Low Level Output Voltage (*) 4.5 4.5 4.5 4.5 VI = V I L or VI H IO=-50 µA 4.4 4.5 4.4 IO=-8 mA 4.18 4.31 4.13 V I (*) = VI H IO=50 µA 0.0 0.1 0.1 IO=8 mA 0.17 0.26 0.33 V V V V V Input Leakage Current 5.5 VI = 5.5V or GND ±0.1 ±1.0 µA Quiescent Supply Current 5.5 VI = VCC or GND 1 10 µA (*) All outputs loaded. AC ELECTRICAL CHARACTERISTICS (CL = 50pF, Input tr = tf =6 ns) Symbol Parameter Test Con dition Output Transition Time 4.5 Value o T A = 25 C Min. Typ . Max. 7.0 15.0 Propagation Delay Time 4.5 20.0 V CC (V) tTLH tTHL tPLH tPHL Unit o -40 to 85 C Min. Max. 19.0 ns 41.0 ns 33.0 (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5V ± 0.5V CAPACITIVE CHARACTERISTICS Symbol Parameter Test Co nditio ns Value o T A = 25 C Min. Typ . Max. Unit o -40 to 85 C Min. Max. CIN Input Capacitance 3.5 pF C PD Power Dissipation Capacitance (note 1) 20 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/4 (per Gate) 3/7 74HCT132 TEST CIRCUIT CL = 15/50 pF or equivalent (includes jig and probe capacitance) RT =ZOUT of pulse generator (typically 50Ω) WAVEFORM: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) 4/7 74HCT132 Plastic DIP-14 MECHANICAL DATA mm DIM. MIN. a1 0.51 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 0.050 0.100 P001A 5/7 74HCT132 SO-14 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45 (typ.) D 8.55 E 5.8 8.75 0.336 6.2 0.228 0.344 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8 (max.) P013G 6/7 74HCT132 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics 1998 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. . 7/7