STMICROELECTRONICS TDA7245

TDA7245
5W AUDIO AMPLIFIER WITH MUTING AND STAND-BY
MUTING AND STAND-BY FUNCTIONS
VOLTAGE RANGE UP TO 30V
HIGH SUPPLY VOLTAGE REJECTION
SVR TYP = 50dB (f = 100Hz)
MUSIC POWER = 12W (RL = 4Ω, d = 10%)
PROTECTION AGAINST CHIP OVER
TEMPERATURE
Powerdip 9+9
DESCRIPTION
The TDA7245 is a monolithic integrated circuit in
9+9 POWERDIP package, intended for use as
ORDERING NUMBER: TDA7245
low frequency power amplifier in a wide range of
applications in radio and TV sets.
Figure 1: Test and Application Circuit
March 1995
1/11
TDA7245
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
VS
Supply Voltage
30
V
IO
Output Peak Current (non repetitive t = 100µs)
3
A
IO
Output Peak Current (repetitive, f > 20Hz)
2.5
A
Ptot
Power Dissipation at Tamb = 80°C
at T case = 70°C
1
6
W
W
Tstg, Tj
Storage and junction Temperature
-40 to 150
°C
PIN CONNECTION (Top view)
THERMAL DATA
Symbol
Rth j-case
Rth j-amb
2/11
Description
Thermal Resistance junction-case
Thermal Resistance junction-ambient
Max
Max
Value
Unit
15
70
°C/W
°C/W
TDA7245
ELECTRICAL CHARACTERISTICS (Refer to the test circuit, Tamb = 25°C, f = 1kHz; unless otherwise
specified).
Symbol
Parameter
Test Condition
Min.
Typ.
Max.
Unit
30
V
11.6
V
17
21
35
mA
mA
VS
Supply Voltage
VO
Quiescent Output Voltage
VS = 24V
Id
Quiescent Drain Current
VS = 14V
VS = 28V
d = 1%, f = 1KHz
VS = 14V, R L = 4Ω
VS = 18V, R L = 8Ω
4
4
W
W
5
5
W
W
12
W
PO
Output Power
12
d = 10%, f = 1KHz
VS = 14V, R L = 4Ω
VS = 18V, R L = 8Ω
4
Music Power (*)
VS = 24V, d = 10%, RL = 4Ω
d
RI
Harmonic Distortion
VS = 14V, R L = 4Ω,
PO = 50mW to 3W
f = 1KHz
f = 10KHz
0.15
0.8
VS = 18V, R L = 8Ω,
PO = 50mW to 3.5W
f = 1KHz
f = 10KHz
0.12
0.5
%
%
VS = 22V, R L = 16Ω,
PO = 50mW to 3W
f = 1KHz
f = 10KHz
0.08
0.4
%
%
Input Impedance
f = 1kHz
BW
Small signal bandwidth (-3dB)
PO = 1W; R L = 4Ω VS = 14V
GV
Voltage Gain (open loop)
f = 1kHz
GV
Voltage Gain (closed loop)
f = 1kHz
eN
Total Input Noise
B = 22 - 22,000Hz
R s = 50Ω
R s = 1kΩ
R s = 10kΩ
S/N
Signal to Noise Ratio
VS = 18V; RL = 8Ω
PO = 5W; RS = 10KΩ
SVR
Supply Voltage Rejection
VS = 16.5V; R L = 8Ω; f = 100Hz
R s = 10kΩ; Vr = 0.5Vrms
T sd
0.5
30
39
kΩ
50 to 40,000
Hz
75
dB
40
1.7
2
3
40
Thermal shut-down Junction
Temperature
%
%
41
dB
6
mV
µV
µV
86
dB
50
dB
150
°C
MUTE FUNCTION
Symbol
Vm
ATTm
Parameter
Test Condition
Pin 4 DC Voltage
Mute SW Open (play)
Muting Attenuation
f = 100Hz to 10kHz
Min.
60
Typ.
Max.
Unit
6.4
V
65
dB
3/11
TDA7245
ELECTRICAL CHARACTERISTCS (Continued)
STAND-BY FUNCTION
Symbol
Parameter
Test Condition
Min.
Typ.
Vst-by
Pin 5 DC Voltage
Mute SW Open (play)
6.4
Ist- by
Pin 5 Current
Mute SW Closed (st-by)
160
Stand-by Attenuation
f = 100Hz to 10kHz
ATT st-by
Vt
Id st-by
Stand-by Threshold (pin 5)
Stand-by Current
70
Max.
Unit
280
µA
V
90
dB
3.8
VS = 14V
1
V
3
mA
Note (*):
MUSIC POWER CONCEPT
MUSIC POWER is ( according to the IEC clauses n.268-3 of Jan 83) the maximal power which the amplifier is capable of producing across the
rated load resistance (regardless of non linearity) 1 sec after the application of a sinusoidal input signal of frequency 1KHz.
According to this definition our method of measurement comprises the following steps:
1) Set the voltage supply at the maximum operating value -20%
2) Apply a input signal in the form of a 1KHz tone burst of 1 sec duration; the repetition period of the signal pulses is > 60 sec
3) The output voltage is measured 1 sec from the start of the pulse
4) Increase the input voltage until the output signal show a THD = 10%
5) The music power is then V2out/R1, where Vout is the output voltage measured in the condition of point 4) and R1 is the rated load impedance
The target of this method is to avoid excessive dissipation in the amplifier.
Figure 2: Schematic Diagram
4/11
TDA7245
Figure 3: P.C. Board and Components Layout of the Circuit of fig 2 (1:1 scale)
APPLICATION SUGGESTIONS
The recommended values of the external components are those shown on the application circuit of fig.1.
Different values can be used. The following table can help the dsigner.
Component
Rec. Value
R1
20KΩ
St-By Biasing
Purpose
Incorrect St-By Function
Larger than Rec. Value
Smaller than Rec. Value
Feedback
Resistors
Increase of Gain
Decrease of Gain
Decrease of Gain
Increase of Gain
Frequency Stability
Danger of Oscillations
Worse POP and Shorter
Delay at St-By Insertion
R2(*)
27KΩ
R3(*)
270Ω
R4
1Ω
C1
22µF
St-By Capacitor
Longer ON/OFF Delay
Time at St-By IN/OUT
Worse POP and Shorter
Delay at St-By insertion
C2
47µF
SVR Capacitor
Worse Turn-On POP by
VS and St-By
Degradation of SVR
C3
0.1µF
Input Capacitance
Higher Low Frequency
Cut-off
C4
2.2µF
Inverting Input DC
Decoupling
Higher Low Frequency
Cut-off
C5
470µF
Supply Voltage
Danger of Oscillations
C6
0.22µF
Frequency Stability
C7
1000µF
Output DC Decoupling
Danger of Oscillations
Higher Low Frequency
Cut-off
(*) The value of closed loop gain (GV = 1 + R2/R3) must be higher than 25dB.
5/11
TDA7245
Figure 4: DC Output Voltage vs. Supply Voltage
Figure 5: ID vs. Supply Voltage
Figure 6: Output Power vs. Supply Voltage
Figure 7: Output Power vs. Supply Voltage
Figure 8: Output Power vs. Supply Voltage
Figure 9: Distortion vs. Output Power
6/11
TDA7245
Figure 10: Distortion vs. Output Power
Figure 11: Distortion vs. Output Power
Figure 12: Supply Voltage Rejection vs.
Frequency (play)
Figure 13: Power Dissipation & Efficiency vs.
Output Power
Figure 14: Power Dissipation & Efficiency vs.
Output Power
Figure 15: Vpin5 (=Vpin4) vs. Supply Voltage
7/11
TDA7245
Figure 16: Ipin4 (muting) vs. Supply Voltage
Figure 17: Ipin5 (St-By) vs. Supply Voltage
Figure 18: Quiescent Current (St-By) vs. Supply
Voltage
Figure 19: Output Attenuation vs. Vpin5
Figure 20: Quiescent Current vs. Vpin5
MUTING / STAND- BY
The muting function allows to inhibit the output
signal through an external control signal.
It can be used in many cases, when a temporary
inhibition of the output signal is requested, for example:
– in switch-on condition, to avoid preamplifier
power-on transients
– during switching at the input stages
– during the receiver tuning.
The stand-by function is very useful and permits a
complete turn ON/OFF of the device through a
low power signal, which can be provided by a µP.
8/11
TDA7245
THERMAL SHUTDOWN
The presence of a thermal limiting circuit offers
the following advantages:
1)An overload on the output (even if it is permanent), or an above limit ambient temperature
can be easily tolerated since the Tj cannot be
higher than 150°C.
2)The heatsink can have a smaller factor of
safety compared with that of a conventional
circuit. There is no possibility of device damage due to high junction temperature.
If for any reason, the junction temperature increase up to 150°C, the thermal shutdown
simply reduces the power dissipation and the
current consumption.
The maximum allowable power dissipation depends upon the junction-ambient thermal resistance. Fig. 21 shows this dissipable power as a
function of ambient temperature for different thermal resistance.
MOUNTING INSTRUCTIONS
The TDA7245 is assembled in the POWERDIP, in
which 9 pins (from 10 to 18) are attached to the
frame and remove the heat produced by the chip.
Figure 22 shows a PC Board copper area used
as a Heatsink (l = 65mm). The Thermal Resistance Junction-Ambient is 35°C.
Figure 22: Example of Heatsink using PC Board
Copper (l = 65mm)
Figure 21: Maximum Allowable Power
Dissipation vs. Ambient Temperature
9/11
TDA7245
POWERDIP 18 (9+9) PACKAGE MECHANICAL DATA
mm
DIM.
MIN.
a1
0.51
B
0.85
b
b1
TYP.
MAX.
MIN.
TYP.
MAX.
0.020
1.40
0.033
0.50
0.38
0.055
0.020
0.50
D
0.015
0.020
24.80
0.976
E
8.80
0.346
e
2.54
0.100
e3
20.32
0.800
F
7.10
0.280
I
5.10
0.201
L
Z
10/11
inch
3.30
0.130
2.54
0.100
TDA7245
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGSTHOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectronics.
 1996 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A.
11/11