TDA2052 ® 60W Hi-Fi AUDIO POWER AMPLIFIER WITH MUTE / STAND-BY SUPPLY VOLTAGE RANGE UP TO ±25V SPLIT SUPPLY OPERATION HIGH OUTPUT POWER (UP TO 60W MUSIC POWER) LOW DISTORTION MUTE/STAND-BY FUNCTION NO SWITCH ON/OFF NOISE AC SHORT CIRCUIT PROTECTION THERMAL SHUTDOWN ESD PROTECTION DESCRIPTION The TDA2052 is a monolithic integrated circuit in Heptawatt package, intended for use as audio class AB amplifier in TV or Hi-Fi field application. Thanks to the wide voltage range and to the high out current capability it’s able to supply the high- Heptawatt V Heptawatt H ORDERING NUMBERS: TDA2052V TDA2052H est power into both 4Ω and 8Ω loads even in presence of poor supply regulation. The built in Muting/Stand-by function simplifies the remote operations avoiding also switching onoff noises. TEST AND APPLICATION CIRCUIT January 2003 1/14 This is advanced information on a new product now in development or undergoing evaluation. Details are subject to change without notice. TDA2052 ABSOLUTE MAXIMUM RATINGS Symbol Parameter VS IO DC Supply Voltage Ptot Top Power Dissipation Tcase = 70°C Operating Temperature Range Tstg, Tj Value Unit ±25 V Output Peak Current (internally limited) Storage and Junction Temperature 6 A 30 0 to +70 W °C -40 to +150 °C PIN CONNECTION (Top view) tab connected to pin 4 BLOCK DIAGRAM 2/14 7 NON INVERTING INPUT(PLAY) 6 INVERTING INPUT 5 NON INVERTING INPUT(MUTE) 4 -VS 3 STAND-BY/MUTE 2 +VS 1 OUTPUT D95AU326 TDA2052 THERMAL DATA Symbol Rth j-case Description Thermal Resistance Junction-case Max Value Unit 2.5 °C/W ELECTRICAL CHARACTERISTICS (Refer to the test circuit, GV = 32dB; VS + 18V; f = 1KHz; Tamb = 25°C, unless otherwise specified.) Symbol VS Parameter Supply Range Iq Ib Total Quiescent Current Input Bias Current VOS Input Offset Voltage IOS PO Input Offset Current PO d Test Condition VS = +22V Music Output Power IEC268-3 Rules (*) VS = + 22.5, RL = 4Ω, d = 10%, t = 1s Output Power (continuous RMS) d = 10% RL = 4Ω RL = 8Ω VS = +22V, R L = 8Ω Total Harmonic Distortion Min. +6 Typ. Max. +25 Unit V 20 40 70 +0.5 mA µA +15 mV +200 nA 50 60 W 35 40 22 33 W W W d = 1% RL = 4Ω RL = 8Ω VS = +22V, R L = 8Ω 32 17 28 W W W RL = 4Ω PO = 0.1 to 20W; f = 100Hz to 15KHz 0.1 0.7 0.1 0.5 30 VS + 22V, RL = 8Ω PO = 0.1 to 20W; f = 100Hz to 15KHz SR GV Slew Rate Open Loop Voltage Gain eN Total Input Noise Ri SVR TS 3 A Curve f = 20Hz to 20KHz Input Resistance Supply Voltage Rejection 5 80 2 3 % V/µs dB 10 500 f = 100Hz, Vripple = 1VRMS % µV µV KΩ 40 50 145 dB °C 1 1.8 V Thermal Shutdown MUTE/STAND-BY FUNCTION (Ref. –VS) VTST-BY Stand-by - Threshold VTPLAY Iq ST-BY Play Threshold Quiescent Current @ Stand-by ATTST-BY Ipin3 2.7 1 Vpin 3 = 0.5V Stand-by Attenuation Pin 3 Current @ Stand-by 70 4 3 90 –1 V mA dB +10 µA Note (*): MUSIC POWER CONCEPT MUSIC POWER is ( according to the IEC clauses n.268-3 of Jan 83) the maximal power which the amplifier is capable of producing across the rated load resistance (regardless of non linearity) 1 sec after the application of a sinusoidal input signal of frequency 1KHz. According to this definition our method of measurement comprises the following steps: 1) Set the voltage supply at the maximum operating value -10% 2) Apply a input signal in the form of a 1KHz tone burst of 1 sec duration; the repetition period of the signal pulses is > 60 sec 3) The output voltage is measured 1 sec from the start of the pulse 4) Increase the input voltage until the output signal show a THD = 10% 5) The music power is then V2out/R1, where Vout is the output voltage measured in the condition of point 4) and R1 is the rated load impedance The target of this method is to avoid excessive dissipation in the amplifier. 3/14 TDA2052 APPLICATIONS SUGGESTIONS (See Test and Application Circuit) The recommended values of the external components are those shown on the application circuit. Different values can be used; the following table can help the designer. Comp. Value R1 22KΩ (*) Purpose Larger Than Smaller Than Input Impedance Increase of Input Impedance Decrease of Input Impedance Decrease of Gain Increase of Gain Increase of Gain Decrease of Gain Danger of oscillations Danger of oscillations Higher Low-frequency cut-off Higher Low-frequency cut-off R2 560Ω R3 22KΩ (*) Closed Loop Gain set to 32dB (**) R4 R5 22KΩ (*) 22KΩ Input Impedance @ Mute Stand-by Time Constant R6 C1 4.7Ω 1µF Frequency Stability Input DC Decoupling C2 10µF Feedback DC Decoupling C3 10µF Stand-by Time Constant C4 0.100µF Frequency Stability C5, C6 1000µF Supply Voltage Bypass Danger of Oscillations (*) R1 = R3 = R4 for POP optimization (**) Closed Loop Gain has to be ≥ 30dB TYPICAL CHARACTERISTICS Figure 1: Output Power vs. Supply Voltage 4/14 Figure 2: Distortion vs. Output Power TDA2052 Figure 3: Output Power vs. Supply Voltage. Figure 4: Distortion vs. Output Power. Figure 5: Distortion vs. Frequency. Figure 6: Distortion vs. Frequency. Figure 7: Quiescent Current vs. Supply Voltage Figure 8: Supply Voltage Rejection vs. Frequency. 5/14 TDA2052 Figure 9: Bandwidth. Figure 10: Output Attenuation & Quiescent Current vs. Vpin3. Figure 11: Total Power Dissipation & Efficiency vs. Output Power. Figure 12: Total Power Dissipation & Efficiency vs. Output Power. 6/14 TDA2052 Figure 13: P.C. Board and Components Layout of the Circuit of Fig. 14 (1:1 scale) Figure 14: Demo Board Schematic. 7/14 TDA2052 MUTE/STAND-BY FUNCTION The pin 3 (MUTE/STAND-BY) controls the amplifier status by three different thresholds, referred to -VS. When its voltage is lower than the first threshold (1V, with a +70mV hysteresis), the amplifier is in STAND-BY and all the final stage current generFigure 15. 8/14 ators are off. Only the input MUTE stage is on in order to prevent pop-on problems. At Vpin3=1.8V the final stage current generators are switched on and the amplifier operates in MUTE. For Vpin3 =2.7V the amplifier is definitely on (PLAY condition) TDA2052 SHORT-CIRCUIT PROTECTION The TDA 2052 has an original circuit which protects the device during accidental short-circuit between output and GND / -Vs / +Vs, taking it in STAND-BY mode, so limiting also dangerous DC current flowing throught the loudspeaker. If a short-circuit or an overload dangerous for the final transistors are detected, the concerned SOA circuit sends out a signal to the latching circuit (with a 10µs delay time that prevents fast random spikes from inadvertently shutting the amplifier off) which makes Q1 and Q2 saturate (see Block Diagram). Q1 immediately short-circuits to ground the A point turning the final stage off while Q2 short-circuits to ground the external capacitor driving the pin 3 (Mute/Stand-by) towards zero potential. Only when the pin 3 voltage becomes lower than 1V, the latching circuit is allowed to reset itself and restart the amplifier, provided that the shortcircuit condition has been removed. In fact, a window comparator is present at the output and it is aimed at preventing the amplifier from restarting if the output voltage is lower than 0.35 Total Supply Voltage or higher than 0.65 Total Supply Voltage. If the output voltage lies between these two thresholds, one may reasonably suppose the short-circuit has been removed and the amplifier may start operating again. The PLAY/MUTE/STAND-BY function pin (pin 3) is both ground- and positive supply-compatible and can be interfaced by means of the R5, C3 net either to a TTL or CMOS output (µ-Processor) or to a specific application circuit. The R5, C3 net is fundamental, because connecting this pin directly to a low output impedance driver such as TTL gate would prevent the correct operation during a short-circuit. Actually a final stage overload turns on the protection latching circuit that makes Q2 try to drive the pin 3 voltage under 0.8 V. Since the maximum current this pin can stand is 3 mA, one must make sure the following condition is met: R5 ≥ THERMAL PROTECTION The thermal protection operates on the 125µA current generator, linearly decreasing its value from 90°C on. By doing this, the A voltage slowly decreases thus switching the amplifier first to MUTE (at 145°C) and then to STAND-BY (155°C). Figure 16: Thermal Protection Block Diagram The maximum allowable power dissipation depends on the size of the external heatsink (thermal resistance case-ambient); figure 17 shows the dissipable power as a function of ambient temperature for different thermal resistance. Figure 17: Maximum Allowable Power Dissipation vs. Ambient Temperature. (VA − 0.7V) 3mA that yields: R5, min = 1.5 KΩ with VA=5V. In order to prevent pop-on and -off transients, it is advisable to calculate the C3, R5 net in such a way that the STAND-BY/MUTE and MUTE/PLAY threshold crossing slope (positive at the turn-on and vice-versa) is less than 100 V/sec. 9/14 TDA2052 APPLICATION NOTES 90W MULTIWAY SPEAKER SYSTEM The schematic diagram of figure 18, shows the solution that we have closen as a suggestion for Hi-Fi and especially TV applications. The multiway system provides the separation of the musical signal not only for the loudspeakers, but also for the power amplifiers with the following advantages: Figure 18: Multiway Application Circuit 10/14 - reduced power level required of each individual amplifier - complete separation of the ways (if an amplifier is affected by clipping distortion, the others are not) - protection of tweeters (the high power harmonics generated by low frequency clipping can not damage the delicate tweeters that are driven by independent power amplifier) - high power dedicated to low frequencies TDA2052 As shown in Figure 19, the R-C passive network for low-pass and High-pass give a cut with a slope of 12dB/octave A further advantage of this application is that connecting each speaker direcly to its amplifier, the musical signal is not modified by the variations of the impedance of the crossover over frequency. The subwoofer is designed for obtaining high sound pressure level with low distortion without stereo effect. In the application of figure 18, the subwoofer plays the 20 to 300 Hz frequency range, while the remaining 300 Hz to 20KHz are sent to two separate channels with stereo effect. The multiway system makes use of three TDA2052, one for driving the subwoofer with POUT higher than 40W (THD = 10%), 28W undistorted (THD = 0.01%), while the others two TDA2052 are used for driving the mid/high frequency speakers of L/R channels, delivering POUT = 25W (THD = 10%) and 20W @ THD = 0.01% Figure 19: Frequency Response Figure 20: Distortion vs Output Power (Subwoofer) Figure 21:Distortion vs Output Power (Midrange/Tweeter) 11/14 TDA2052 DIM. A C D D1 E E1 F G G1 G2 H2 H3 L L1 L2 L3 L4 L5 L6 L7 L9 L10 L11 M M1 V4 Dia MIN. 2.4 1.2 0.35 0.7 0.6 2.34 4.88 7.42 10.05 16.7 21.24 22.27 2.6 15.1 6 2.1 4.3 2.55 4.83 mm TYP. 2.54 5.08 7.62 16.9 14.92 21.54 22.52 2.8 15.5 6.35 0.2 MAX. 4.8 1.37 2.8 1.35 0.55 0.97 0.8 2.74 5.28 7.82 10.4 10.4 17.1 21.84 22.77 1.29 3 15.8 6.6 MIN. 0.094 0.047 0.014 0.028 0.024 0.095 0.193 0.295 0.396 0.657 0.386 0.877 0.102 0.594 0.236 2.7 0.082 4.8 0.169 3.05 0.100 5.33 0.190 40 (typ.) 3.85 0.144 2.8 5.08 3.65 inch TYP. 0.100 0.200 0.300 0.668 0.587 0.848 0.891 0.110 0.610 0.250 0.008 0.110 0.200 MAX. 0.189 0.054 0.110 0.053 0.022 0.038 0.031 0.105 0.205 0.307 0.409 0.409 0.673 OUTLINE AND MECHANICAL DATA Weight: 1.90gr 0.860 0.896 0.051 0.118 0.622 0.260 0.106 0.190 0.120 0.210 Heptawatt V 0.152 L E L1 M1 A M D C D1 H2 L2 L5 L3 F E E1 V4 L9 H3 G G1 G2 Dia. F L10 L4 H2 L11 L7 L6 12/14 HEPTAMEC 0016069 TDA2052 mm DIM. MIN. TYP. A inch MAX. MIN. TYP. MAX. 4.80 C 1.37 0.054 D 2.40 2.80 0.094 0.11 D1 1.20 1.35 0.047 0.053 E 0.35 0.55 0.014 0.022 E1 0.70 0.97 0.03 0.036 F 0.60 0.80 0.024 G 2.34 2.54 2.74 0.092 0.1 0.108 G1 4.88 5.08 5.28 0.192 0.2 0.208 G2 7.42 7.62 7.8 0.292 0.3 0.307 H2 0.031 10.40 H3 10.05 0.41 10.40 0.395 0.409 L1 3.90 4.20 4.50 0.153 0.165 L2 18.10 18.40 18.70 0.712 0.724 0.736 L3 4.88 5.08 5.28 0.192 0.2 0.208 L4 0.177 1.29 0.05 L5 2.60 3.00 0.102 0.118 L6 15.10 15.80 0.594 0.622 L7 6.00 6.60 0.236 L9 3.9 4.5 0.153 L10 2.10 2.70 0.083 0.106 L13 4.30 4.80 0.169 0.189 V5 4.2 OUTLINE AND MECHANICAL DATA 0.188 0.260 0.165 0.177 Heptawatt H 89˚ (Min.), 90˚ (Typ.), 91˚ (Max.) DIA 3.65 3.85 0.143 0.151 C A V5 D L1 L9 D1 E L3 L2 F G L7 H2 L4 L5 G1 G2 H2 H3 F F Dia. Resin between leads E E1 L10 L6 L11 HEPTHMEC.EPS 0080180 13/14 TDA2052 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 14/14