U813BS/U813BSE 1.1-GHz Prescaler for PLLs in TV, CATV and SAT TV Tuners Technology: Bipolar Features D D D D U813BS ECL output stage U813BSE emitter-follower output stage 3 scaling factors 64/128/256, programmable at Pin 5 High input sensitivity D D D D Low output impedance Low power consumption Pin-compatible to the U6xxB-series except Pin 5 Electrostatic protection according to MIL-STD. 883 Case 8-pin dual-inline plastic 8-pin SO plastic 6-pin SIP plastic (U813BS, U813BSE) (U813BS-FP, U813BSE-FP) (U813BS-SP, U813BSE-SP) Block Diagram Figure 1. Block diagram TELEFUNKEN Semiconductors Rev. A1, 05-Sep-96 1 (7) U813BS/U813BSE Absolute Maximum Ratings Reference point pin 4 (1) Parameters Supply voltage Input-voltage range Junction temperature Storage-temperature range Ambient-temperature range Pin 8 (4) Pin 2, 3, 5 (2, 5, 6) Symbol VS Vi Ti Tstg Tamb Value 6 0 to VS 125 –40 to +125 –25 to +70 Unit V V °C °C °C Symbol Value 100 100 175 Unit Thermal Resistance Parameters Junction ambient DIP8 SIP6 SO8 RthJA K/W Note: The device is self-oscillating without input signal Pin Description (Dip8, SO8) Pin 1 2, 3 4 5 6, 7 8 Function Not connected Input Ground Switch 64/128/256 Output VS Pin Description (SIP6) Pin 1 2 3 4 5,6 Function Ground Switch 64/128/256 Output VS Input Notes: Pin numbers without brackets apply to DIP8 and SO8 package, Pin numbers with brackets to SIP6 RMS voltage calculated from the available power measured 2 (7) TELEFUNKEN Semiconductors Rev. A1, 05-Sep-96 U813BS/U813BSE Electrical Characteristics VS = 4.5 to 5.5 V, Tamb = 0 to +70_C, referred to test circuit, unless otherwise specified Parameters Supply current Input sensitivity Large-signal compatibility Test Conditions / Pin VS = 5 V U813BS Pin 8 (4) U813BSE Pin 8 (4) RG = 50 W fi = 70 to 1000 MHz Pin 2, 3 (5, 6) fi = 1000 to 1100 MHz Pin 2, 3 (5, 6) RG = 50 W Pin 2, 3 (5, 6) Frequency q y range g Output stage a. Balanced ECL output Voltage swing each output Output impedance b. Emitter follower Voltage swing each output Output impedance Switching g voltage g for Symbol Min. Typ. Max. Unit 35 38 45 50 mA mA Vi 10 mV Vi 15 mV IS IS Vi fimin fimax 300 1100 RL = 10 k//13 pF Pin 6, 7 (3) Pin 6, 7 (3) VO ZO 0.8 RL = 10 k//13 pF Pin 6, 7 (3) Pin 6, 7 (3) ./. 64 Pin 5 (2) ./. 128 Pin 5 (2) ./. 256 Pin 5 (2) VO ZO VSF VSF VSF 1 TELEFUNKEN Semiconductors Rev. A1, 05-Sep-96 mV 70 MHz Vpp W 500 Vpp W 200 open VS –0.5 0 0.5 V V 3 (7) U813BS/U813BSE Test Circuits Figure 2. L1 = L2 = 150 nH (6 turns CuL 0.45 mm Ĭ on 4 mm Ĭ) Figure 3. 4 (7) TELEFUNKEN Semiconductors Rev. A1, 05-Sep-96 U813BS/U813BSE Output Circuits Figure 4. Figure 5. TELEFUNKEN Semiconductors Rev. A1, 05-Sep-96 5 (7) U813BS/U813BSE Dimensions in mm 6 (7) TELEFUNKEN Semiconductors Rev. A1, 05-Sep-96 U813BS/U813BSE Ozone Depleting Substances Policy Statement It is the policy of TEMIC TELEFUNKEN microelectronic GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances ( ODSs). The Montreal Protocol ( 1987) and its London Amendments ( 1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. TEMIC TELEFUNKEN microelectronic GmbH semiconductor division has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency ( EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively. TEMIC can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use TEMIC products for any unintended or unauthorized application, the buyer shall indemnify TEMIC against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. TEMIC TELEFUNKEN microelectronic GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423 TELEFUNKEN Semiconductors Rev. A1, 05-Sep-96 7 (7)