HS3A THRU HS3M 3.0 AMPS. High Efficient Surface Mount Rectifiers Voltage Range 50 to 1000 Volts Current 3.0 Amperes SMC/DO-214AB Features Glass passivated junction chip. For surface mounted application Low forward voltage drop Low profile package Built-in stain relief, ideal for automatic placement Fast switching for high efficiency High temperature soldering: 260℃/10 seconds at terminals .129(3.27) .118(3.0) .245(6.22) .220(5.59) .280(7.11) .260(6.60) .012(.31) .006(.15) Plastic material used carries Underwriters Laboratory Classification 94V-O .103(2.62) .079(2.00) Mechanical Data Cases: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packing: 16mm tape per E1A STD RS-481 Weight: 0.21 gram .008(.20) .004(.10) .060(1.52) .030(0.76) .320(8.13) .305(7.75) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol HS HS HS Type Number 3A Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 2 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 3.0A Maximum DC Reverse Current @ TA =25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Operating Temperature Range VRRM VRMS VDC 50 35 50 3B 3D HS 3F HS 3G HS 3J HS 3K 100 200 300 400 600 800 1000 70 140 210 280 420 560 700 100 200 300 400 600 800 1000 Units V V V I(AV) 3.0 A IFSM 150 A 1.0 VF 1.3 1.7 V 75 50 uA uA nS pF ℃ ℃ 10.0 200 IR Trr Cj 50 80 TJ -55 to +150 -55 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Mounted on P.C.B. with 0.6”x0.6” ( 16 x 16 mm ) Copper Pad Areas. Storage Temperature Range HS 3M TSTG - 252 - RATINGS AND CHARACTERISTIC CURVES (HS3A THRU HS3M) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE trr AVERAGE FORWARD CURRENT. (A) 50W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm SET TIME BASE FOR 5/ 10ns/ cm FIG.3- TYPICAL REVERSE CHARACTERISTICS 3.0 2.5 2.0 1.5 1.0 P.C.B.MOUNTED 0.6X0.6"(16X16mm) COPPER PAD AREAS 0.5 0 25 50 75 100 125 150 175 o AMBIENT TEMPERATURE. ( C) FIG.4- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 100 Tj=25 0C 10 1 .1 20 40 60 80 100 S3 -H 10 1.0 0.1 0.01 120 .2 .4 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) .6 .8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) FIG.6- TYPICAL JUNCTION CAPACITANCE FIG.5- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 175 300 150 JUNCTION CAPACITANCE.(pF) PEAK FORWARD SURGE CURRENT. (A) 3A Tj=25 0C HS Tj=100 0C HS HS 3G 3J -H S3 M INSTANTANEOUS FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. ( A) D 1000 200 100 0 1 10 100 1000 125 100 HS HS 75 3J- 3A- HS HS 3G 3M 50 25 .1 .5 1 2 5 10 20 REVERSE VOLTAGE. (V) NUMBER OF CYCLES AT 60Hz - 253 - 50 100 200 500 1000