Series AMLDV-NZ Up to 700mA | LED Driver FEATURES: • • • • • • • • High Power LED Driver Ultra Wide Input Voltage Range Remote ON/OFF Function SMD Package Constant Current Output mode High Efficiency (Up to 96%) PWM & Analogue Dimming Function Operating Temperature range -40ºC - +85ºC Models Single output Model Input Voltage (V) Output Voltage (V) Output Current (mA) Efficiency Max (%) 5.5-48 5.5-48 5.5-48 5.5-48 5.5-48 3.3-36 3.3-36 3.3-36 3.3-36 3.3-36 300 350 500 600 700 96 96 96 96 96 AMLDV-4830-NZ AMLDV-4835-NZ AMLDV-4850-NZ AMLDV-4860-NZ AMLDV-4870-NZ NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Voltage range Absolute Maximum Rating(≤10sec) 24 Typical Quiescent input current in Shutdown mode Dimming Control (Digital Control) Dimming Control (Analog Control) (Leave open if not used) Input Filter Units VDC VDC ON: Open or 2.8V> V <6V On/Off Control (Analog Control) (Leave open if not used) Remote pin current Maximum 5.5-48 5-55 OFF: V <0.6V V=5V 1 mA Vin=24V, V<0.6V 400 µA Max PWM Frequency: 200Hz Input Voltage Range (Vin=5.5-48V) 0-15V Output Current Range(Vin=5.5-48V) 0-100% Control Voltage Range(Full ON) 0.2V±50mV Control Voltage Range(Full OFF) 4.5V±50mV Driving Current(V=5V) 0.2mA(max) Capacitor Output Specifications Parameters Current accuracy Short Circuit protection Efficiency Max load capacitance Ripple & Noise Temperature coefficient Output Current Stability Internal Power Dissipation Conditions Typical At full load 20MHz Bandwidth -40 oC to+71 oC Vin=48V, Vo=3.3~36V Vin=24V,5LEDS Maximum ±2 ±3 Continuous, Automatic Recovery 96 1000 120 ±0.015 ±1 700 Units % % µF mV p-p %/oC % mW General Specifications Parameters Switching frequency Operating temperature Storage temperature Max Case temperature Cooling Humidity www.aimtec.com F 051e R12.A Conditions Typical Maximum Units 100% load 300mA,350mA 500mA,600mA,700mA 370 320-420 100 KHz o C o C o C o C 95 % RH -40 to +85 -40 to+71 -55 to +125 Free Air Convection Tel: +1 514 620 2722 1 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDV-NZ Up to 700mA | LED Driver General Specifications (continued) Parameters Conditions Case material Potting material Weight Dimensions (L x W x H) MTBF Typical Maximum Units Plastic UL94-VO Epoxy Resin(Flammability UL94V-0) 6 0.939 × 0.713 × 0.315 inches 23.86 × 18.10 × 8.00 mm >2 000 000 hrs (MIL-HDBK-217 F at +25 oC) g Safety Specifications Parameters Designed to meet: EN 55022, class B, IEC/EN 61000-4-2 (Perf. Criteria B), IEC/EN 61000-4-3 (Perf. Criteria B), IEC/EN 61000-4-4 (Perf. Criteria B), IEC/EN 61000-4-5 (Perf. Criteria B), IEC/EN 61000-4-5 (Perf. Criteria B) Standards Pin Out Specifications Single Pin 1 7 8 9 10 16 -V Input Remote On/Off PWM Dimming -V Output +V Output Analogue Dimming +V Input DC Supply PWM/ON/OFF or not used LED Cathode connection LED Anode connection Analogue Dimming or not used + DC Supply Dimensions Top View 23.86 (0.94) 1.02 (0.04) 2.54 (0.10) Front View 16 10 A 9 0.25 (0.01) 18.10 (0.71) 13.70 (0.54) A 1 7 8 0.25 (0.01) Side View 8.00 7.50 (0.32) (0.30) 5.00º max 1.40 ± 0.20 (0.055 ±0.008) MAX 3.04 (0.12) www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 2 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDV-NZ Up to 700mA | LED Driver Derating Typical Application Circuits www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 3 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDV-NZ Up to 700mA | LED Driver PWM Dimming Control PWM Digital Control Signal PWM Digital Control Signal PWM Digital Control Signal 1 1 1 0 0 0 1 1 1 0 0 0 Output Current Output Current LEDs appear Dim Output Current LEDs appear bright NOTE: Formula is for reference; actual output current may depend on loading. The Time On of pulse must be > 0.7mS Analogue Dimming Control +Vin 9 +Vout 16 1 AMLDV-NZ -Vout -Vin 1 5.1K 10 7 8 1 0 to 10VDC 5.6K On/Off (Optional) www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 4 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDV-NZ Up to 700mA | LED Driver Recommended EMC Circuit Analogue Dimming 10 1,25mH +Vin 9 +Vout 16 1 470 µF SMCG51 1.0 µF 1 AMLDV-NZ 2.2 µF -Vout 1.0 µF 1 8 7 -Vin 1 PWM Dimming ON/OFF Recommended AC Input Circuit Analogue Dimming AC In 5Vac to 32Vac 0.1uF optional 10 +Vin 16 100uF to 330uF + - 9 +Vout 1 AMLDV-NZ 1 -Vin 7 -Vout 8 1 AC In PWM Dimming ON/OFF www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 5 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDV-NZ Up to 700mA | LED Driver Efficiency versus Input Voltage www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 6 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDV-NZ Up to 700mA | LED Driver www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 7 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDV-NZ Up to 700mA | LED Driver Output Current versus Dimming Voltage NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 8 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only