AIMTEC AMSR1.5-783.3-NZ

Series AMSR1.5-78-NZ
Up to 9.75 Watt | DC-DC Converter
FEATURES:
•
•
•
•
Models
Single output
Model
AMSR1.5-782.5-NZ
AMSR1.5-783.3-NZ
AMSR1.5-7805-NZ
AMSR1.5-786.5-NZ
3 Pin SIP Package
Pin-out compatible with LM78XX Linear Regulators
Continuous Short Circuit Protection
Non-Isolated Regulated Output
Input Voltage
(V)
4.75-18
4.75-18
6.5-18
8-18
Output Voltage
(V)
2.5
3.3
5
6.5
•
•
•
•
Operating temperature -40°C to +85°C
Wide input range
Very High Efficiency Up To 95%
Low ripple and noise
Output Current
max (A)
1.5
1.5
1.5
1.5
Efficiency
Vin Min (%)
85
88
91
93
Efficiency
Vin Max (%)
88
91
93
95
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Input Specifications
Voltage range
Filter
Quiescent Current
Short Circuit consumption
Output Specifications
Output Specifications
Voltage accuracy
Short Circuit protection
Short circuit restart
Output current limit
Thermal shutdown
Dynamic load stability
Line voltage regulation
Load voltage regulation
Temperature coefficient
Ripple & Noise
Maximum Capacitive Load
General Specifications
Input Specifications
Switching frequency
Operating temperature
Storage temperature
Max Case temperature
Cooling
Humidity
Case material
Weight
Dimensions (L x W x H)
MTBF
Soldering Temperature
www.aimtec.com
F 051e R12.A
Nominal
Typical
Vin=(LL-HL) at full load
See the table above
Capacitor
5
0.5
Conditions
Typical
Internal IC junction
10-100% load
Vin=(LL-HL) at full load
10-100% load
-40°C to +85°C ambient
20MHz Bandwidth
150
±0.75
±1
±0.02
45
Conditions
Typical
100% load
±3
Continuous.
Auto recovery
100% load
With derating above 71°C
340
Maximum
Units
10
1.8
mA
W
Maximum
Units
5
1000
A
ºC
mV
%
%
o
%/ C
mV p-p
µF
Maximum
Units
±100
-40 to +85
-55 to +125
Free air convection
100
95
Non-conductive black plastic (UL94-V0 rated)
4
0.45 X 0.35 X 0.69 inch
11.50 X 8.90 X 17.50 mm
> 2 000 000 hrs (MIL-HDBK-217F, Ground Benign, t=+25°C)
1.5 mm from case for 10 sec
300
Tel: +1 514 620 2722
1 of 4
VDC
%
KHz
o
C
o
C
o
C
%
g
o
C
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMSR1.5-78-NZ
Up to 9.75 Watt | DC-DC Converter
Pin Out Specifications
Pin
1
2
3
Single
+Vin
GND
+Vout
Dimensions
Footprint
Front
View
11.50
(0.45
2.54
(0.10)
8.90
(0.35)
Ø 1.0 +0.15/-0
(Ø 0.04 + 0.006/-0
3.21
(0.13)
www.aimtec.com
2
Dimensions are typical values: mm (inch)
General Tolerance: ± 0.25 (± 0.01)
Pin Tolerance: ± 0.1 (± 0.004)
3
0.50
(0.024)
2.54
(0.10)
DIV: 2.54 (0.1)
Bottom
View
2.15
(0.09)
0.30
(0.012)
4.10
(0.16)
1
F 051e R12.A
2.54
(0.10)
0.50
(0.024)
17.50
(0.69)
Side
View
Tel: +1 514 620 2722
2 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMSR1.5-78-NZ
Up to 9.75 Watt | DC-DC Converter
Derating
Free Air Convection
71º C
Output Power (%)
100
80
Safe Operating Area
60
40
20
0
- 20
- 40
0
20
40
60
80
85
100
Ambient Temperature º C
Typical Application Circuits
+Vin
3 +Vout
1
C1
10uF
GND
AMSR1.5-78Z
2
C2
22uF
GND
C1: A low ESR capacitor is required to keep the noise of the converter to a minimum. Ceramic capacitors are recommended
with typical value is 10µF / 25V.
C2: Installation of C2 is recommended with typical value of 22µF / 16V ceramic for 5V and 6.5V output signal and 22µF /
6.3V ceramic for 2.5V and 3.3V output signal.
NOTE: This part is not designed for parallel operation.
www.aimtec.com
F 051e R12.A
Tel: +1 514 620 2722
3 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMSR1.5-78-NZ
Up to 9.75 Watt | DC-DC Converter
Dual Output Connection
+Vout
3
1
+Vin
AMSR1.5-78Z
C1
10uF
C2
2
22uF
GND
GND
3
1
AMSR1.5-78Z
C1
C2
2
22uF
10uF
-Vout
Input Filter
10uH ~ 47uH
3 +Vout
1
C1
C1
10uF
10uF
AMSR1.5-78Z
C2
2
22uF
GND
GND
Output Filter
10uH ~ 47uH
3
1
C1
10uF
AMSR1.5-78Z
2
+Vout
C1
C1
10uF
10uF
C2
22uF
GND
GND
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R12.A
Tel: +1 514 620 2722
4 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only