www.fairchildsemi.com Application Note AN-3001 Optocoupler Input Drive Circuits An optocoupler is a combination of a light source and a photosensitive detector. In the optocoupler, or photon coupled pair, the coupling is achieved by light being generated on one side of a transparent insulating gap and being detected on the other side of the gap without an electrical connection between the two sides (except for a minor amount of coupling capacitance). In the Fairchild Semiconductor optocouplers, the light is generated by an infrared light emitting diode, and the photo-detector is a silicon diode which drives an amplifier, e.g., transistor. The sensitivity of the silicon material peaks at the wavelength emitted by the LED, giving maximum signal coupling. dropped across the resistor at the desired IF, determined from other criteria. A silicon diode is shown installed inversely parallel to the LED. This diode is used to protect the reverse breakdown of the LED and is the simplest method of achieving this protection. The LED must be protected from excessive power dissipation in the reverse avalanche region. A small amount of reverse current will not harm the LED, but it must be guarded against unexpected current surges. Where the input to the optocoupler is a LED, the input characteristics will be the same, independent of the type of detector employed. The LED diode characteristics are shown in Figure 1. The forward bias current threshold is shown at approximately 1 volt, and the current increases exponentially, the useful range of IF between 1 mA and 100 mA being delivered at a VF between 1.2 and 1.3 volts. The dynamic values of the forward bias impedance are current dependent and are shown on the insert graph for RDF and ∆R as defined in the figure. Reverse leakage is in the nanoampere range before avalanche breakdown. The brightness of the IR LED slowly decreases in an exponential fashion as a function of forward current (IF) and time. The amount of light degradation is graphed in Figure 6 which is based on experimental data out to 20,000 hours. A 50% degradation is considered to be the failure point. This degradation must be considered in the initial design of optoisolator circuits to allow for the decrease and still remain within design specifications on the current-transfer-ratio (CTR) over the design lifetime of the equipment. Also, a limitation on IF drive is shown to extend useful lifetime of the device. The LED equivalent circuit is represented in Figure 2, along with typical values of the components. The diode equations are provided if needed for computer modeling and the constants of the equations are given for the IR LED’s. Note that the junction capacitance is large and increases with applied forward voltage. An actual plot of this capacitance variation with applied voltage is shown on the graph of Figure 3. It is this large capacitance controlled by the driver impedance which influences the pulse response of the LED. The capacitance must be charged before there is junction current to create light emission. This effect causes an inherent delay of 10-20 nanoseconds or more between applied current and light emission in fast pulse conditions. In some circumstances it is desirable to have a definite threshold for the LED above the normal 1.1 volts of the diode VF. This threshold adjustment can be obtained by shunting the LED by a resistor, the value of which is determined by a ratio between the applied voltage, the series resistor, and the desired threshold. The circuit of Figure 7 shows the relationship between these values. The calculations will determine the resistor values required for a given IFT and VA. It is also quite proper to connect several LED’s in series to share the same IF. The VF of the series is the sum of the individual VF’s. Zener diodes may also be used in series. The LED is used in the forward biased mode. Since the current increases very rapidly above threshold, the device should always be driven in a current mode, not voltage driven. The simplest method of achieving the current drive is to provide a series current-limiting resistor, as shown in Figure 4, such that the difference between VAPP and VF is The forward voltage of the LED has a negative temperature coefficient of 1.05 mV/°C and the variation is shown in Figure 5. Where the input applied voltage is reversible or alternating and it is desired to detect the phase or polarity of the input, the bipolar input circuit of Figure 8 can be employed. The individual optocouplers could control different functions or be paralleled to become polarity independent. Note that in this connection, the LED’s protect each other in reverse bias. REV. 4.00 4/30/02 AN-3001 APPLICATION NOTE VF - FORWARD VOLTAGE (VOLTS) ∆R = 300Ω 1.5 30Ω 3Ω IF RS 1.4 RDF= 13Ω 1.3 1.2 FORWARD BIAS IF mA 100 120Ω TA = 25˚C 1.1 1.0 Cj D Vj D - IDEAL DIODE I 10KΩ 0.9 60 0.8 0.1 16 RP SLOPE V = RDF = 80 14 VF SLOPE 1.0 10 100 ∆V = ∆R = ∆I 40 AVALANCHE 18 VF 1KΩ IF - FORWARD CURRENT (mA) 20 LED EQUIVALENT CIRCUIT 0.3Ω 20 12 10 8 6 4 2 0 0.5 1.0 1.5 0 - - - - 1 10 1.0 <10 1.1 V 100 mA 100 300 500 RP >109 THRESHOLD REVERSE BIAS 55 RS 0.1 BVR - Cj IR VF VOLTS RANGE OF IF Vj 0.01 VR -5 1.2 - pF 1.3 V 0 - - - nA ∞ 30 3 0.3 Ω - - - - Ω 1.0 IF = IFT exp 10 100 VF - VFT k VF = VFT + k log NOTE CHANGE OF SCALES mA IF IFT For IRLED (940nm) IR VFTH = 0.98V IFTH = 0.10mA K = 0.360 Figure 1. Characteristics of IR LED RS = 0.03V IF (A) Figure 2. Equivalent Circuit Equations JUNCTION CAPACITANCE (Cj) - pF 350 300 250 200 IF R= R VAPP - VF IF 150 LED VAPP VF 100 NOTE SCALE CHANGE Figure 4. Typical LED Drive Circuit 50 VF 1.5 1.0 VR 0.5 0 1 2 3 APPLIED VOLTAGE 4 5 6 7 8 Figure 3. Voltage Dependence of Junction Capacitance 2 REV. 4.00 4/30/02 APPLICATION NOTE AN-3001 IFT 1.4 R2 PROVIDES A THRESHOLD VF V -V R1 = A F R2 IFT R1 FORWARD VOLTAGE - VF (VOLTS) IFT = 1.3 VA T = -55°C VF R2 1.2 Figure 7. LED Threshold Adjustment T = +25°C 1.1 1.0 1 T = +100°C IF VF 0.9 R1 2 0.8 0.1 VA 0.2 0.5 1 2 5 10 20 R2 50 100 VF FORWARD CURRENT - IF (mA) Figure 8. Bipolar Input Selects LED NORMALIZED CTR DEGRADATION - % Figure 5. IR Forward Voltage vs. Forward Current and Temperature R1 50 40 30 00 20 IF =1 IF= 10 IF = 8 6 4 75 60 mA VA mA R2 VF mA 0 mA IF = 3 Figure 9. High Threshold Bipolar Input IF = 10 mA 2 TA = 25°C 1 10 100 1000 10,000 100,000 TIME - HOURS Figure 6. Brightness Degredation vs. Forward Current and Time IF R1 + - EXTERNAL SWITCH DEVICE 120V RMS 60 Hz VR 2 R2 + C1 R3 - Figure 10. AC Input to LED Drive Circuit Another method of obtaining a high threshold for high level noise immunity is shown in Figure 9, where the LED’s are in inverse series with inverse parallel diodes to conduct the opposite polarity currents. In this circuit, the VF is the total REV. 4.00 4/30/02 forward drop of the LED and silicon diode in series. The resistors serve their normal threshold and current limiting functions. The silicon diodes could be replaced by LED’s from other optocouplers or visible signal indicators. 3 AN-3001 APPLICATION NOTE AC Mains Monitoring Logic to Logic Interface In some situations it may be necessary to drive the LED from a 120 VRMS, 60 Hz or 400 Hz source. Since the LED responds in nanoseconds, it will follow the AC excursions faithfully, turning on and off at each zero-crossing of the input. If a constant output is desired from the optocoupler detector as in AC to logic coupling, it is necessary to rectify and filter the input to the LED. The circuit of Figure 10 illustrates a simple filtering scheme to deliver a DC current to the LED. In some cases the filter could be designed into the detector side of the optocoupler, allowing the LED to pulse at line frequency. In the circuit of Figure 10, the value of C1 is selected to reduce the variations in the IF between half cycles below the current that is detectable by the detector portion. This condition usually means that the detector is functioning in saturation, so that minor variations of IF will not be sensed. The values of R1, R2 and R3 are adjusted to optimize the filtering function, R3C1 time constant, etc. Speed of turn-off may be a determining factor. More complicated transistor filtering may be required, such as that shown in Figure 11, where a definite time delay, rise time and fall time can be designed in. In this circuit, C1 and R3 serve the same basic function as in Figure 10. The transistor provides a high impedance load to the R4C2 filter network, which once reaching the VF value, suddenly turns on the LED and pulls the transistor quickly into saturation. The turn-off transient consists of the discharge of C1, through R3 and the LED. In logic-to logic coupling using the optocoupler, a simple transistor drive circuit can be used as shown in Figure 12. In the normally-off situation, the LED is energized only when the transistor is in saturation. The design equations are given for calculating the value of the series current limiting resistor. With the transistor off, only minor collector leakage current will flow through the LED. If this small leakage is detectable in the optocoupler detector, the leakage can be bypassed around the LED by the addition of another resistor in parallel with the LED shown as R1. The value of R1 can be large, calculated so that the leakage current develops less than threshold VF (~0.8 volt) from Figure 5. The drive transistor can be the normal output current sink of a TTL or DTL integrated circuit, which will sink 16 mA at 0.2 volt nominal and up to 50 mA in saturation. If the logic is not capable of sinking the necessary IF, an auxiliary drive transistor can be employed to boost current capability. The circuit of Figure 13 shows how a PNP transistor is connected as an emitter follower, or common collector, to obtain current gain. When the output of the gate (G1) is low, Q1 is turned on and current flows through the LED. The calculation of R1 must now include the base-emitter forward biased voltage drop, VBE, as shown in the figure. DC INPUT FROM BRIDGE RECTIFIER IF R3 + R4 C1 VF 10K=R1 C2 R2=10K - Figure 11. R-C-Transistor Filter Circuit VCC + IF R VCC = 5 V IF = 20 mA VSAT = 0.4 V VF = 1.2 V R= R1 R1 = VCC - VF - VBE - VCE(SAT)GATE IF VBE(Q1) = 0.6 V VCE(SAT)(G1) = 0.4 V R1 10K IF OUTPUT VCC - VF - VSAT IF = 5 - 1.2 - 0.4 = 3.4 20 20 VF VCC VCC VF R = 170Ω INPUT (VSAT) G1 VBE Q1 VCE(SAT) Figure 12. Transistor Drive, Normally Off 4 Figure 13. Logic to LED Series Booster REV. 4.00 4/30/02 APPLICATION NOTE AN-3001 In the normally on situation of Figure 14, the transistor is required to shunt the IF around the LED, with a VSAT of less than threshold VF. Typical switching transistors have saturation voltages less than 0.4 volts at IC=20 mA or less. The value of the series resistor is determined to provide the required IF with the transistor off. situations a “pulse” is defined as an on-off transient occurring and ending before thermal equilibrium is established between the LED, the lead frame, and the ambient. This equilibrium will normally occur within one millisecond. For a pulse width in the microsecond range, the IF can be driven above the DC ratings, if the duty cycle is low. The chart of Figure 16 shows the relationship between the amount of overdrive, duty cycle, and pulse width. The overdrive is normalized to the IDC value listed as maximum on the device data sheet. Average power dissipation is the limiting parameter at high duty cycles and short pulse widths. For longer pulse widths, the equilibrium temperature occurs at lower duty cycle values, and peak power is the limiting parameter. Again, if the logic cannot sink the IF, a booster transistor can be employed as shown in Figure 15. With the output of the gate low, the transistor Q1 will be on and the sum of VCE (SAT) of G1 and VBE of Q1, will be less than the threshold VF of the LED. With the gate high, Q1 is not conducting and LED is on. The value of R1 is calculated normally, but shunt current will be greater than IF. The normally-on or normally-off conditions are selected depending on the required function of the detector portion of the optocoupler and fail-safe operation of the circuits. For duty cycles of 1% or less the pulse becomes similar to a nonrecurrent surge allowing additional ratings such as the I2t used in rectifier diodes. Average current is used for lifetime calculation. The pulse response of the detector must be considered in choosing drive conditions. In many applications it is found necessary to pulse drive the LED to values beyond the DC ratings of the device. In these VCC - VF IF 3.8 = = 190Ω 20 VCC R= IF R1 = VCC - VF IF R R1 INPUT (VSAT) VF G1 VCC VCC IF 10K OUTPUT VBE Q1 VCE(SAT) Figure 14. Transistor Drive, Normally On Figure 15. Logic to LED Shunt Booster 100 1 µS 5 µS 10 µS IPK IDC PW = 30 µsec 10 100 µS 300 µS 1 0.1 1.0 10 100 DUTY CYCLE - % Figure 16. Maximum Peak IF Pulse Normalized to Max IDC for Pulse Width (PW) and Duty Cycle (%) REV. 4.00 4/30/02 5 AN-3001 APPLICATION NOTE LED Current Shunting Techniques There are situations where it is not desirable to pass all of the input current through the LED. One method to achieve this is to provide a bypass resistor as suggested in Figure 7 for threshold adjustment. This method is satisfactory where the input current is switched on and off completely, but if the information on the current is only a small variation riding on a constant DC level, the bypass resistor also bypasses a large portion of the desired signal around the LED. Two methods can be used to retrieve the signal with little attenuation. If the signal has a rapid variation (e.g., the audio signal on a telephone line), the DC component can be cancelled in the detector by feedback circuits. If the variation is slow, a dynamic shunt can be used instead of the fixed resistor. If a constant-current device or circuit is used in parallel with the LED, as shown in Figure 17, the adjusted component of the DC will flow through the dynamic impedance, and any current variations will result in a change of terminal voltage. Therefore, the total current change will flow through the paralleled LED circuit. The graph of Figure 18 shows the performance of this particular circuit adjusted to center on IL=120mA and a circuit node voltage of 3.4 volts. In the circuit shown, the detector portions of the CNY17-1 and CNY17-4 were employed for convenience. Note that in Figure 18 most of the current variation occurs as IF. The ratio between the DC resistance (RD) and dynamic impedance (Rd) for the shunt is 50, which represents the signal transfer gain achieved over a fixed resistor. 125 IL 2.7K ITH IL2W IF = 10 mA 3.4V LED R = 200Ω HIIB2 1.7V 220Ω β>10K VA I - mA 120 115 MCT2 β>200 0.5V CNY17-4 LED 30Ω 110 IL SANS LED 1 R = 1.6K 105 3.0 3.1 3.2 3.4 3.6 3.8 4.0 TERMINAL VOLTAGE - VA Figure 17. Constant-Current Shunt Impedance Figure 18. Shunt Impedance Performance 6 REV. 4.00 4/30/02 AN-3001 APPLICATION NOTE DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 4/30/02 0.0m 001 Stock#AN300000xx 2002 Fairchild Semiconductor Corporation