DUAL POWER DRIVER HYBRID DUAL POWER DRIVER HYBRID SILICON INTEGRATED CIRCUIT The MCH2890 dual Power Driver is capable of driving a wide variriety of inductive and resistive loads, included are hammer solenoids in high-speed digital printrers, paper-tape punchers and stepper motors in computer operated plotters. ? ? ? ? ? ? High Current - to 6.0 Amperes High Breakdown Voltage BVCEX = 120V min. MTTL Compatibility Separate Integrated Circuit and Darlington Power Grounds Low Vsat at 3.0 and 6.0 Amperes Low Leakage Current - 0.1 µA typ 10 1 bottom view CASE 685 METAL PACKAGE MAXIMUM RATINGS (TA - +25°C unless otherwise noted Rating Symbol Value Unit 8.0 1.0 A +5Vdc 8 VCC-1 IC Collector current Peak Continous Collector Emitter Berakdown Voltage Minimum at IC < 0.5 mA VCC-2 5 6 MC 3101 7 BVCEX (pins 1, 5) 120 Power Supply Voltage (Integrated Circuit) VCC 1 7.0 Vdc Power Dissipation and Theermal Characteristics TA 25 °C Derate above TA = 25 °C Thermal Resistance Junction to air TC 25 °C Derate babove TC = 25 °C Thermal Resistance Junction to Case PD 1/ JA 1/ JA PD 1/ JC 1/ JC 3.75 25 40 25 167 6.0 Watts mW/°C °C/W Watts mW/°C °C/W Operating Temperature Range TA 0 to +70 °C Storage Temperature Range Tstg -55 to +175 °C Vdc 4 GND 1 9 MC 3101 10 2 GND GND 3 ELECTRICAL CHARACTERISTICS Test procedures are shown for only one power driver. The other power driver Is tested in the same manner. AMPERES IOL1 0 °C 25 °C 75 °C Characteristics Input forward Current Symbol IF Pin Under Test 50 6 6 Imput Clamp Voltage VD 6 Output Voltage (See figure 1) VOL1 VOL2 BVCEX 5 5 5 ICEX 5 Output Power Supply Drain Current IPDL Output Power Supply Drain Current Output Leakage Current Switching Parameters (See figure 21) Turn-On Delay Time Turn-Off Delay Time Max 2.0 IR Input Breakdown Voltage Min 6 BVin Input Lockage current TEST LIMITS 25 °C 0 °C Min Typ -2.0 -2.0 mAdc 50 50 µAdc Min IOL1 IOL2 IC(max ) VIH VIL VF VR VCC1 VCC2 VCCIL VCCIH VRH 1.0 - 10 - 0.5 - 2.0 1.8 1.8 1.1 - 0.4 0.4 0.4 2.4 - 5.0 5.0 5.0 90 - 4.5 4.5 4.5 5.5 5.5 5.5 4.0 4.0 4.0 Iin ID IC(max) VIH VIL VF VR VCC1 VCC2 6 VCCIL GND 7 2,3,4 2,3,4 8 6 - µAdc 8 30 mAdc 8 IPDH 8 120 mAdc 8 6,7,9 , 10 2,3,4 IpdIpd+ 5,6 5,6 8 8 7 7 2,3,4 2,3,4 µs µs 5 6 - 6 2,3,4 Vdc 0.26 18 5 - 2,3,4 8 1.5 2.5 0.1 5 -- VRH 8 6 Vdc VCCIH 8 6 Vdc 120 VOLTS ID TEST CURRENT/VOLTAGE APPLIED TO PNS BELOW Unit 5.5 6.0 - mA Iin 75 °C Max Max 3.0 - IOL2 5 5 5 Pulse In Pulse Out 6 6 5 5 7 7 7 2,3,4 2,3,4 2,3,4 7 2,3,4 2,3,4 , 6.7.9 . 10 5.0 V ½ MC 2890 CARBON RESISTOR LOAD ADJUST FOR 2.0A or 6.0A CURRENT PROBE PULSE GEN MC 3101 SCOPE TEKTRONICS SAMPLING SCOPE 4.0 V ½ MC 2890 MC 3101 INPUT 5.0 V 0V OUTPUT MC 3101