INTEL GE28F128W18TD60

Intel® Wireless Flash Memory (W18)
28F320W18, 28F640W18, 28F128W18
Datasheet
Product Features
■
■
■
High Performance Read-While-Write/
Erase
— Burst frequency at 66 MHz
— 60 ns Initial Access Read Speed
— 11 ns Burst-Mode Read Speed
— 20 ns Page-Mode Read Speed
— 4-, 8-, 16-, and Continuous-Word Burst
Mode Reads
— Burst and Page Mode Reads in all
Blocks, across all partition boundaries
— Burst Suspend Feature
— Enhanced Factory Programming at
3.1 µs/word (typ.for 0.13 µm)
Security
— 128-bit Protection Register
— 64-bits Unique Programmed by Intel
— 64-bits User-Programmable
— Absolute Write Protection with VPP at
Ground
— Individual and Instantaneous Block
Locking/Unlocking with Lock-Down
Capability
Quality and Reliability
— Temperature Range: –40 °C to +85 °C
— 100k Erase Cycles per Block
— 0.13 µm ETOX™ VIII Process
— 0.18 µm ETOX™ VII Process
■
■
■
Architecture
— Multiple 4-Mbit Partitions
— Dual Operation: RWW or RWE
— 8KB parameter blocks
— 64KB main blocks
— Top or Bottom Parameter Devices
— 16-bit wide data bus
Software
— 5 µs (typ.) Program and Erase Suspend
Latency Time
— Flash Data Integrator (FDI) and Common
Flash Interface (CFI) Compatible
— Programmable WAIT Signal Polarity
Packaging and Power
— 0.13 µm: 32-, 64-, and 128-Mbit in VF
BGA Package; 128-Mbit in QUAD+
Package
— 0.18 µm: 32- and 128-Mbit Densities in
VF BGA Package; 64-Mbit Density in
µBGA* Package
— 56 Active Ball Matrix, 0.75 mm BallPitch
— VCC = 1.70 V to 1.95 V
— VCCQ = 1.70 V to 2.24 V or 1.35 V to
1.80 V
— Standby current (0.13 µm): 8µA (typ.)
— Read current: 7mA (typ.)
The Intel® Wireless Flash Memory (W18) device with flexible multi-partition dual operation,
provides high-performance asynchronous and synchronous burst reads. It is an ideal memory for
low-voltage burst CPUs. Combining high read performance with flash memory’s intrinsic nonvolatility, the W18 device eliminates the traditional system-performance paradigm of shadowing
redundant code memory from slow nonvolatile storage to faster execution memory. It reduces
the total memory requirement that increases reliability and reduces overall system power
consumption and cost.
The W18 device’s flexible multi-partition architecture allows programming or erasing to occur
in one partition while reading from another partition. This allows for higher data write
throughput compared to single partition architectures. The dual-operation architecture also
allows two processors to interleave code operations while program and erase operations take
place in the background. The designer can also choose the size of the code and data partitions via
the flexible multi-partition architecture.
Notice: This document contains information on new products in production. The specifications
are subject to change without notice. Verify with your local Intel sales office that you have the
latest datasheet before finalizing a design.
290701-009
December 2003
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY
ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN
INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS
ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES
RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER
INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
The 1.8 Volt Intel® wireless flash memory datasheet may contain design defects or errors known as errata which may cause the product to deviate
from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by calling 1-800548-4725 or by visiting Intel's website at http://www.intel.com.
Copyright © 2003, Intel Corporation.
*Other names and brands may be claimed as the property of others.
2
Datasheet
Contents
Contents
1.0 Introduction ...............................................................................................................................9
1.1
1.2
1.3
Document Purpose ...............................................................................................................9
Nomenclature .......................................................................................................................9
Conventions..........................................................................................................................9
2.0 Device Description ................................................................................................................10
2.1
2.2
2.3
2.4
Product Overview ...............................................................................................................10
Package Diagram ...............................................................................................................12
Signal Descriptions .............................................................................................................14
Memory Map and Partitioning .............................................................................................15
3.0 Device Operations .................................................................................................................18
3.1
3.2
3.3
Bus Operations ...................................................................................................................18
3.1.1 Read ......................................................................................................................18
3.1.2 Burst Suspend .......................................................................................................19
3.1.3 Standby..................................................................................................................19
3.1.4 Reset .....................................................................................................................19
3.1.5 Write ......................................................................................................................20
Device Commands .............................................................................................................20
Command Sequencing .......................................................................................................24
4.0 Read Operations ....................................................................................................................25
4.1
4.2
4.3
4.4
4.5
Read Array..........................................................................................................................25
Read Device ID...................................................................................................................25
Read Query (CFI) ...............................................................................................................26
Read Status Register..........................................................................................................26
Clear Status Register..........................................................................................................28
5.0 Program Operations .............................................................................................................28
5.1
5.2
5.3
Word Program ....................................................................................................................28
Factory Programming .........................................................................................................29
Enhanced Factory Program (EFP) .....................................................................................30
5.3.1 EFP Requirements and Considerations.................................................................30
5.3.2 Setup .....................................................................................................................31
5.3.3 Program .................................................................................................................31
5.3.4 Verify......................................................................................................................31
5.3.5 Exit.........................................................................................................................32
6.0 Program and Erase Operations .......................................................................................34
6.1
6.2
6.3
Program/Erase Suspend and Resume ...............................................................................34
Block Erase.........................................................................................................................36
Read-While-Write and Read-While-Erase ..........................................................................38
7.0 Security Modes .......................................................................................................................39
7.1
Datasheet
Block Lock Operations ........................................................................................................39
7.1.1 Lock .......................................................................................................................40
7.1.2 Unlock ....................................................................................................................40
3
Contents
7.2
7.3
7.1.3 Lock-Down............................................................................................................. 40
7.1.4 Block Lock Status .................................................................................................. 41
7.1.5 Lock During Erase Suspend .................................................................................. 41
7.1.6 Status Register Error Checking ............................................................................. 41
7.1.7 WP# Lock-Down Control ....................................................................................... 42
Protection Register ............................................................................................................. 42
7.2.1 Reading the Protection Register............................................................................ 43
7.2.2 Programing the Protection Register....................................................................... 43
7.2.3 Locking the Protection Register............................................................................. 44
VPP Protection ................................................................................................................... 45
8.0 Set Configuration Register ................................................................................................ 46
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
Read Mode (CR[15])........................................................................................................... 48
First Access Latency Count (CR[13:11]) ............................................................................ 48
8.2.1 Latency Count Settings.......................................................................................... 49
WAIT Signal Polarity (CR[10]) ............................................................................................ 50
WAIT Signal Function ......................................................................................................... 50
Data Hold (CR[9]) ............................................................................................................... 51
WAIT Delay (CR[8]) ............................................................................................................ 52
Burst Sequence (CR[7])...................................................................................................... 52
Clock Edge (CR[6])............................................................................................................. 54
Burst Wrap (CR[3]) ............................................................................................................. 54
Burst Length (CR[2:0])........................................................................................................ 54
9.0 Power Consumption............................................................................................................. 55
9.1
9.2
9.3
9.4
9.5
Active Power....................................................................................................................... 55
Automatic Power Savings (APS) ........................................................................................ 55
Standby Power ................................................................................................................... 55
Power-Up/Down Characteristics......................................................................................... 55
9.4.1 System Reset and RST# ....................................................................................... 56
9.4.2 VCC, VPP, and RST# Transitions ......................................................................... 56
Power Supply Decoupling................................................................................................... 56
10.0 Thermal and DC Characteristics ..................................................................................... 57
10.1
10.2
10.3
10.4
Absolute Maximum Ratings ................................................................................................ 57
Operating Conditions .......................................................................................................... 57
DC Current Characteristics (.13 ∝µ and .18 µµ)................................................................. 58
DC Voltage Characteristics................................................................................................. 60
11.0 AC Characteristics ................................................................................................................ 62
11.1
11.2
11.3
11.4
11.5
11.6
11.7
Read Operations – .13 µµ Λιτηογραπηψ............................................................................ 62
Read Operations – .18 µµ Λιτηογραπηψ............................................................................ 64
AC Write Characteristics..................................................................................................... 74
Erase and Program Times.................................................................................................. 79
Reset Specifications ........................................................................................................... 80
AC I/O Test Conditions ....................................................................................................... 81
Device Capacitance............................................................................................................ 82
Appendix A Write State Machine States ............................................................................... 83
Appendix B Common Flash Interface .................................................................................... 86
4
Datasheet
Contents
Appendix C Mechanical Specifications.................................................................................95
Appendix D Ordering Information .........................................................................................100
Datasheet
5
Contents
Revision History
Date of
Revision
Version
09/13/00
-001
Description
Initial Release
Deleted 16-Mbit density
Revised ADV#, Section 2.2
Revised Protection Registers, Section 4.16
Revised Program Protection Register, Section 4.18
Revised Example in First Access Latency Count, Section 5.0.2
Revised Figure 5, Data Output with LC Setting at Code 3
Added WAIT Signal Function, Section 5.0.3
Revised WAIT Signal Polarity, Section 5.0.4
Revised Data Output Configuration, Section 5.0.5
Added Figure 7, Data Output Configuration with WAIT Signal Delay
Revised WAIT Delay Configuration, Section 5.0.6
Changed VCCQ Spec from 1.7 V – 1.95 V to 1.7 V – 2.24 V in Section 8.2,
Extended Temperature Operation
01/29/01
-002
Changed ICCS Spec from 15 µA to 18 µA in Section 8.4, DC
Characteristics
Changed ICCR Spec from 10 mA (CLK = 40 MHz, burst length = 4) and 13
mA (CLK = 52 MHz, burst length = 4) to 13 mA, and 16 mA respectively in
Section 8.4, DC Characteristics
Changed ICCWS Spec from 15 µA to 18 µA in Section 8.4, DC
Characteristics
Changed ICCES Spec from 15 µA to 18 µA in Section 8.4, DC
Characteristics
Changed tCHQX Spec from 5ns to 3ns in Section 8.6, AC Read
Characteristics
Added Figure 25, WAIT Signal in Synchronous Non-Read Array Operation
Waveform
Added Figure 26, WAIT Signal in Asynchronous Page Mode Read
Operation Waveform
Added Figure 27, WAIT Signal in Asynchronous Single Word Read
Operation Waveform
Revised Appendix E, Ordering Information
Revised entire Section 4.10, Enhanced Factory Program Command (EFP)
and Figure 6, Enhanced Factory Program Flowchart
Revised Section 4.13, Protection Register
Revised Section 4.15, Program Protection Register
Revised Section 7.3, Capacitance, to include 128-Mbit specs
06/12/01
-003
Revised Section 7.4, DC Characteristics, to include 128-Mbit specs
Revised Section 7.6, AC Read Characteristics, to include 128-Mbit device
specifications
Added tVHGL Spec in Section 7.6, AC Read Characteristics
Revised Section 7.7, AC Write Characteristics, to include 128-Mbit device
specifications
Minor text edits
6
Datasheet
Contents
Date of
Revision
Version
Description
New Sections Organization
Added 16 Word Burst Feature
Added Burst Suspend Section
Revised Block Locking State Diagram
Revised Active Power Section
Revised Automatic Power Savings Section
Revised Power-Up/Down Operation Section
Revised Extended Temperature Operation
04/05/02
-004
Added 128Mb DC Characteristics Table
Added 128 Mb AC Read Characteristics
Revised Table 17. Test Configuration Component Values for Worst Case
Speed Conditions
Added .13 µ Product DC and AC Read Characteristics
Revised AC Write Characteristics
Added Read to Write and Write to Read Transition Waveforms
Revised Reset Specifications
Various text edits
Various text edits
10/10/02
-005
11/12/02
-006
Updated Latency Count Section, including adding Latency Count Tables
Added section 8.4 WAIT Function and WAIT Summary Table
Updated Package Drawing and Dimensions
Various text clarifications
Removed Intel Burst Order
01/14/03
-007
Revised Table 22, DC Current Characteristics, ICCS
Revised Table 22, DC Current Characteristics, ICCAPS
Various text edits
Revised Table 22, Read Operations, tAPA
03/21/03
-008
Added note to table 15, Configuration Register Descriptions
Added note to section 3.1.1, Read
Updated Block-Lock Operations (Section 7.1 and Figure 11)
Updated Table 21 (128Mb ICCR)
12/17/03
-009
Updated Table 4 (WAIT behavior)
Added QUAD+ ballout, package mechanicals, and order information
Various text edits including latest product-naming convention
Datasheet
7
Contents
8
Datasheet
Intel® Wireless Flash Memory (W18)
1.0
Introduction
1.1
Document Purpose
This datasheet contains information about the 1.8 Volt Intel® Wireless Flash memory (W18) device
family. Section 1.0 provides a flash memory overview. Section 2.0 through Section 9.0 describe the
memory functionality. Section 10.0 describes the electrical specifications for extended temperature
product offerings. Packaging specifications and order information can be found in Appendix C and
Appendix D, respectively.
1.2
Nomenclature
Many acronyms that describe product features or usage are defined here:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.3
APS - Automatic Power Savings
BBA - Block Base Address
CFI - Common Flash Interface
CUI - Command User Interface
EFP - Enhanced Factory Programming
FDI - Flash Data Integrator
NC - No Connect
OTP - One-Time Programmable
PBA - Partition Base Address
RWE - Read-While-Erase
RWW - Read-While-Write
SRD - Status Register Data
VF BGA - Very thin, Fine pitch, Ball Grid Array
WSM - Write State Machine
Conventions
Many abbreviated terms and phrases are used throughout this document:
• The term “1.8 V” refers to the full VCC voltage range of 1.7 V – 1.95 V (except where noted)
and “VPP = 12 V” refers to 12 V ±5%.
• When referring to registers, the term set means the bit is a logical 1, and clear means the bit is
a logical 0.
• The terms pin and signal are often used interchangeably to refer to the external signal
connections on the package. (ball is the term used for VF BGA).
• A word is 2 bytes, or 16 bits.
Datasheet
9
Intel® Wireless Flash Memory (W18)
• Signal names are in all CAPS (see Section 2.3, “Signal Descriptions” on page 14.)
• Voltage applied to the signal is subscripted, for example, VPP.
Throughout this document, references are made to top, bottom, parameter, and partition. To clarify
these references, the following conventions have been adopted:
• A block is a group of bits (or words) that erase simultaneously with one block erase
instruction.
•
•
•
•
A main block contains 32 Kwords.
A parameter block contains 4 Kwords.
The Block Base Address (BBA) is the first address of a block.
A partition is a group of blocks that share erase and program circuitry and a common status
register.
• The Partition Base Address (PBA) is the first address of a partition. For example, on a 32Mbit top-parameter device, partition number 5 has a PBA of 140000h.
• The top partition is located at the highest physical device address. This partition may be a
main partition or a parameter partition.
• The bottom partition is located at the lowest physical device address. This partition may be a
main partition or a parameter partition.
• A main partition contains only main blocks.
• A parameter partition contains a mixture of main blocks and parameter blocks.
• A top parameter device (TPD) has the parameter partition at the top of the memory map with
the parameter blocks at the top of that partition. This was formerly referred to as top-boot
device.
• A bottom parameter device (BPD) has the parameter partition at the bottom of the memory
map with the parameter blocks at the bottom of that partition. This was formerly referred to as
bottom-boot block flash device.
2.0
Device Description
This section provides an overview of the W18 device features, packaging, signal naming, and
device architecture.
2.1
Product Overview
The W18 device provides Read-While-Write (RWW) and Read-White-Erase (RWE) capability
with high-performance synchronous and asynchronous reads on package-compatible densities with
a 16-bit data bus. Individually-erasable memory blocks are optimally sized for code and data
storage. Eight 4-Kword parameter blocks are located in the parameter partition at either the top or
bottom of the memory map. The rest of the memory array is grouped into 32-Kword main blocks.
The memory architecture for the W18 device consists of multiple 4-Mbit partitions, the exact
number depending on device density. By dividing the memory array into partitions, program or
erase operations can take place simultaneously during read operations. Burst reads can traverse
10
Datasheet
Intel® Wireless Flash Memory (W18)
partition boundaries, but user application code is responsible for ensuring that they don’t extend
into a partition that is actively programming or erasing. Although each partition has burst-read,
write, and erase capabilities, simultaneous operation is limited to write or erase in one partition
while other partitions are in a read mode.
Augmented erase-suspend functionality further enhances the RWW capabilities of this device. An
erase can be suspended to perform a program or read operation within any block, except that which
is erase-suspended. A program operation nested within a suspended erase can subsequently be
suspended to read yet another memory location.
After device power-up or reset, the W18 device defaults to asynchronous read configuration.
Writing to the device’s configuration register enables synchronous burst-mode read operation. In
synchronous mode, the CLK input increments an internal burst address generator. CLK also
synchronizes the flash memory with the host CPU and outputs data on every, or on every other,
valid CLK cycle after an initial latency. A programmable WAIT output signals to the CPU when
data from the flash memory device is ready.
In addition to its improved architecture and interface, the W18 device incorporates Enhanced
Factory Programming (EFP), a feature that enables fast programming and low-power designs. The
EFP feature provides the fastest currently-available program performance, which can increase a
factory’s manufacturing throughput.
The device supports read operations at 1.8 V and erase and program operations at 1.8 V or 12 V.
With the 1.8-V option, VCC and VPP can be tied together for a simple, ultra-low-power design. In
addition to voltage flexibility, the dedicated VPP input provides complete data protection when
VPP ≤ VPPLK.
This device allows I/O operation at voltages even lower than the minimum VCCQ of 1.7 V. This
Extended VCCQ range, 1.35 V – 1.8 V, permits even greater system design flexibility.
A 128-bit protection register enhances the user’s ability to implement new security techniques and
data protection schemes. Unique flash device identification and fraud-, cloning-, or contentprotection schemes are possible through a combination of factory-programmed and user-OTP data
cells. Zero-latency locking/unlocking on any memory block provides instant and complete
protection for critical system code and data. An additional block lock-down capability provides
hardware protection where software commands alone cannot change the block’s protection status.
The device’s Command User Interface (CUI) is the system processor’s link to internal flash
memory operation. A valid command sequence written to the CUI initiates device Write State
Machine (WSM) operation that automatically executes the algorithms, timings, and verifications
necessary to manage flash memory program and erase. An internal status register provides ready/
busy indication results of the operation (success, fail, and so on).
Three power-saving features– Automatic Power Savings (APS), standby, and RST#– can
significantly reduce power consumption. The device automatically enters APS mode following
read cycle completion. Standby mode begins when the system deselects the flash memory by
de-asserting CE#. Driving RST# low produces power savings similar to standby mode. It also
resets the part to read-array mode (important for system-level reset), clears internal status registers,
and provides an additional level of flash write protection.
Datasheet
11
Intel® Wireless Flash Memory (W18)
2.2
Package Diagram
The W18 device is available in a 56-ball VF BGA and µBGA Chip SCale Package with 0.75 mm
ball pitch, or the 88-ball (80 active balls) QUAD+ SCSP package. Figure 1 shows the device
ballout for the VF BGA and µBGA package. Figure 2 shows the device ballout for the QUAD+
package.
Figure 1. 56-Ball VF BGA / µBGA Ballout
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
A
A
A11
A8
VSS
VCC
A12
A9
A20
CLK
VPP
A18
A6
A4
A4
A6
A18
RST#
A17
A5
A3
A3
A5
A17
VPP
VCC
VSS
A8
A11
RST#
CLK
A20
A9
A12
B
B
C
C
A13
A10
A21
ADV#
WE#
A19
A7
A2
A2
A7
A19
WE#
ADV#
A21
A10
A13
D
D
A15
A14
WAIT
A16
DQ12
WP#
A22
A1
A1
A22
WP#
DQ12
A16
WAIT
A14
A15
VCCQ
DQ15
DQ6
DQ4
DQ2
DQ1
CE#
A0
A0
CE#
DQ1
DQ2
DQ4
DQ6
DQ15
VCCQ
E
E
F
F
VSS
DQ14 DQ13
DQ11
DQ10
DQ9
DQ0
OE#
OE#
DQ0
DQ9
DQ10
DQ11
DQ13 DQ14
VSS
G
G
DQ7
VSSQ
DQ5
VCC
DQ3
VCCQ
Top View - Ball Side Down
Complete Ink Mark Not Shown
DQ8
VSSQ
VSSQ
DQ8
VCCQ
DQ3
VCC
DQ5
VSSQ
DQ7
Bottom View - Ball Side Up
NOTES:
1. On lower density devices, upper address balls can be treated as NC. (Example: For 32-Mbit density, A21 and A22 will be NC).
2. See Appendix C, “Mechanical Specifications” on page 95 for mechanical specifications for the package.
12
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 2. 88-Ball (80 Active Balls) QUAD+ Ballout
A
1
2
3
4
5
DU
DU
A4
A18
A19
VSS
A5
R-LB#
A23
VSS
A3
A17
A24
F-VPP,
F-VPEN
A2
A7
A25
F-WP#
A1
A6
A0
D8
D2
D10
R-OE#
D0
D1
D9
6
7
8
DU
DU
A21
A11
A22
A12
R-WE# P1-CS#
A9
A13
ADV#
A20
A10
A15
R-UB# F-RST# F-WE#
A8
A14
A16
D5
D13
WAIT
F2-CE#
D3
D12
D14
D7
F2-OE#
D11
D4
D6
D15
VCCQ
B
F1-VCC F2-VCC
C
S-CS2
CLK
D
E
F
G
H
J
S-CS1# F1-OE#
K
F1-CE# P2-CS# F3-CE# S-VCC
P-VCC F2-VCC
VCCQ
P-Mode,
P-CRE
L
M
VSS
VSS
DU
DU
VCCQ
F1-VCC
VSS
VSS
VSS
VSS
DU
DU
Top View - Ball Side Down
Legend:
Global
SRAM/PSRAM specific
Flash specific
NOTES:
1. Unused upper address balls can be treated as NC (for 128Mbit, A[25:23] are not used).
2. See Appendix C, “Mechanical Specifications” on page 95 for mechanical specifications for the package.
Datasheet
13
Intel® Wireless Flash Memory (W18)
2.3
Signal Descriptions
Table 1 describes ball usage.
Table 1.
Symbol
Signal Descriptions
Type
Name and Function
A[22:0]
I
ADDRESS INPUTS: For memory addresses. 32 Mbit: A[20:0]; 64 Mbit: A[21:0]; 128 Mbit: A[22:0]
D[15:0]
I/O
DATA INPUTS/OUTPUTS: Inputs data and commands during write cycles; outputs data during
memory, status register, protection register, and configuration code reads. Data pins float when the
chip or outputs are deselected. Data is internally latched during writes.
ADV#
I
ADDRESS VALID: ADV# indicates valid address presence on address inputs. During synchronous
read operations, all addresses are latched on ADV#’s rising edge or the next valid CLK edge with
ADV# low, whichever occurs first.
CE#
I
CHIP ENABLE: Asserting CE# activates internal control logic, I/O buffers, decoders, and sense amps.
De-asserting CE# deselects the device, places it in standby mode, and tri-states all outputs.
CLK
I
CLOCK: CLK synchronizes the device to the system bus frequency during synchronous reads and
increments an internal address generator. During synchronous read operations, addresses are latched
on ADV#’s rising edge or the next valid CLK edge with ADV# low, whichever occurs first.
OE#
I
OUTPUT ENABLE: When asserted, OE# enables the device’s output data buffers during a read cycle.
When OE# is deasserted, data outputs are placed in a high-impedance state.
RST#
I
RESET: When low, RST# resets internal automation and inhibits write operations. This provides data
protection during power transitions. de-asserting RST# enables normal operation and places the
device in asynchronous read-array mode.
WAIT
O
WAIT: The WAIT signal indicates valid data during synchronous read modes. It can be configured to be
asserted-high or asserted-low based on bit 10 of the Configuration Register. WAIT is tri-stated if CE# is
deasserted. WAIT is not gated by OE#.
WE#
I
WRITE ENABLE: WE# controls writes to the CUI and array. Addresses and data are latched on the
rising edge of WE#.
WP#
I
WRITE PROTECT: Disables/enables the lock-down function. When WP# is asserted, the lock-down
mechanism is enabled and blocks marked lock-down cannot be unlocked through software. See
Section 7.1, “Block Lock Operations” on page 39 for details on block locking.
ERASE AND PROGRAM POWER: A valid voltage on this pin allows erasing or programming. Memory
contents cannot be altered when VPP ≤ VPPLK. Block erase and program at invalid VPP voltages should
not be attempted.
VPP
Pwr/I
Set VPP = VCC for in-system program and erase operations. To accommodate resistor or diode drops
from the system supply, the VIH level of VPP can be as low as VPP1 min. VPP must remain above VPP1
min to perform in-system flash modification. VPP may be 0 V during read operations.
VPP2 can be applied to main blocks for 1000 cycles maximum and to parameter blocks for 2500 cycles.
VPP can be connected to 12 V for a cumulative total not to exceed 80 hours. Extended use of this pin
at 12 V may reduce block cycling capability.
VCC
Pwr
DEVICE POWER SUPPLY: Writes are inhibited at VCC ≤ VLKO. Device operations at invalid VCC
voltages should not be attempted.
VCCQ
Pwr
OUTPUT POWER SUPPLY: Enables all outputs to be driven at VCCQ. This input may be tied directly to
VCC.
VSS
Pwr
GROUND: Pins for all internal device circuitry must be connected to system ground.
14
Datasheet
Intel® Wireless Flash Memory (W18)
Table 1.
Symbol
VSSQ
Signal Descriptions
Type
Name and Function
Pwr
OUTPUT GROUND: Provides ground to all outputs which are driven by VCCQ. This signal may be tied
directly to VSS.
DU
DON’T USE: Do not use this pin. This pin should not be connected to any power supplies, signals or
other pins and must be floated.
NC
NO CONNECT: No internal connection; can be driven or floated.
2.4
Memory Map and Partitioning
The W18 device is divided into 4-Mbit physical partitions, which allows simultaneous RWW or
RWE operations and allows users to segment code and data areas on 4-Mbit boundaries. The
device’s memory array is asymmetrically blocked, which enables system code and data integration
within a single flash device. Each block can be erased independently in block erase mode.
Simultaneous program and erase operations are not allowed; only one partition at a time can be
actively programming or erasing. See Table 2, “Bottom Parameter Memory Map” on page 16 and
Table 3, “Top Parameter Memory Map” on page 17.
The 32-Mbit device has eight partitions, the 64-Mbit device has 16 partitions, and the 128-Mbit
device has 32 partitions. Each device density contains one parameter partition and several main
partitions. The 4-Mbit parameter partition contains eight 4-Kword parameter blocks and seven 32Kword main blocks. Each 4-Mbit main partition contains eight 32-Kword blocks each.
The bulk of the array is divided into main blocks that can store code or data, and parameter blocks
that allow storage of frequently updated small parameters that are normally stored in EEPROM. By
using software techniques, the word-rewrite functionality of EEPROMs can be emulated.
.
Datasheet
15
Intel® Wireless Flash Memory (W18)
Table 2.
16
64 Mbit
Blk #
128 Mbit
32
262
7F8000-7FFFFF
..
.
Blk #
..
.
32 Mbit
..
.
Blk #
32
135
400000-407FFF
3F8000-3FFFFF
134
3F8000-3FFFFF
..
.
..
.
..
.
..
.
134
..
.
32
32
71
200000-207FFF
71
200000-207FFF
1F8000-1FFFFF
70
1F8000-1FFFFF
70
1F8000-1FFFFF
..
.
100000-107FFF
32
38
0F8000-0FFFFF
38
0F8000-0FFFFF
38
0F8000-0FFFFF
0C0000-0C7FFF
32
30
0B8000-0BFFFF
30
0B8000-0BFFFF
30
0B8000-0BFFFF
080000-087FFF
32
22
078000-07FFFF
22
078000-07FFFF
22
078000-07FFFF
14
038000-03FFFF
..
.
038000-03FFFF
32
8
008000-00FFFF
8
008000-00FFFF
8
008000-00FFFF
4
7
007000-007FFF
7
007000-007FFF
7
007000-007FFF
..
.
14
..
.
038000-03FFFF
..
.
14
..
.
32
..
.
040000-047FFF
..
.
15
..
.
040000-047FFF
..
.
15
..
.
040000-047FFF
..
.
15
..
.
32
..
.
..
.
23
..
.
080000-087FFF
..
.
23
..
.
080000-087FFF
..
.
23
..
.
32
..
.
..
.
31
..
.
0C0000-0C7FFF
..
.
31
..
.
0C0000-0C7FFF
..
.
31
..
.
32
..
.
..
.
..
.
39
..
.
..
.
100000-107FFF
..
.
..
.
39
..
.
..
.
100000-107FFF
..
.
39
..
.
32
..
.
..
.
70
..
.
32
..
.
Four
Partitions
One
Partition
One Partition
Parameter Partition
One
Partition
One
Partition
Main Partitions
Eight
Partitions
Sixteen
Partitions
Size
(KW)
Bottom Parameter Memory Map
4
0
000000-000FFF
0
000000-000FFF
0
000000-000FFF
Datasheet
Intel® Wireless Flash Memory (W18)
Top Parameter Memory Map
4
70
1FF000-1FFFFF
134
3FF000-3FFFFF
262
7FF000-7FFFFF
7F8000-7F8FFF
254
7F0000-7F7FFF
7C0000-7C7FFF
32
55
1B8000-1BFFFF
119
3B8000-3BFFFF
247
7B8000-7BFFFF
780000-787FFF
32
47
178000-17FFFF
111
378000-37FFFF
239
778000-77FFFF
39
138000-13FFFF
103
338000-33FFFF
231
738000-73FFFF
700000-707FFF
32
31
0F8000-0FFFFF
95
2F8000-2FFFFF
223
6F8000-6FFFFF
32
0
600000-607FFF
32
63
1F8000-1FFFFF
191
5F8000-5FFFFF
32
0
..
.
192
000000-007FFF
128
400000-407FFF
32
127
3F8000-3FFFFF
..
.
200000-207FFF
..
.
64
..
.
000000-007FFF
..
.
..
.
224
..
.
300000-307FFF
..
.
96
..
.
100000-107FFF
..
.
32
..
.
32
..
.
..
.
32
..
.
740000-747FFF
..
.
232
..
.
340000-347FFF
..
.
104
..
.
140000-147FFF
..
.
40
..
.
32
..
.
..
.
240
..
.
380000-387FFF
..
.
112
..
.
18000-187FFF
..
.
48
..
.
32
..
.
..
.
248
..
.
3C0000-3C7FFF
..
.
120
..
.
1C0000-1C7FFF
..
.
56
..
.
32
..
.
..
.
255
3F0000-3F7FFF
..
.
3F8000-3F8FFF
126
..
.
127
1F0000-1F7FFF
..
.
1F8000-1F8FFF
62
..
.
63
..
.
4
32
..
.
..
.
128 Mbit
..
.
Blk #
..
.
64 Mbit
..
.
Blk #
..
.
32 Mbit
..
.
Blk #
..
.
Size
(KW)
..
.
One Partition
One
Partition
Four
Partitions
Sixteen
Partitions
Eight
Partitions
Main Partitions
One
Partition
One
Partition
Parameter Partition
Table 3.
32
0
000000-007FFF
Datasheet
17
Intel® Wireless Flash Memory (W18)
3.0
Device Operations
This section provides an overview of device operations. The 1.8 Volt Intel® Wireless Flash memory
family includes an on-chip WSM to manage block erase and program algorithms. Its CUI allows
minimal processor overhead with RAM-like interface timings.
3.1
Bus Operations
Table 4.
Bus Operations
Mode
Reset
RST#
CE#
OE#
WE#
ADV#
WAIT
D[15:0]
Notes
VIL
X
X
X
X
High-Z
High-Z
1,2
Write
VIH
VIL
VIH
VIL
VIL
Asserted
DIN
3
Read
VIH
VIL
VIL
VIH
VIL
Active
DOUT
4
Output Disable
VIH
VIL
VIH
VIH
X
Asserted
High-Z
1
Standby
VIH
VIH
X
X
X
High-Z
High-Z
1
NOTES:
1. X = Don’t Care (VIL or VIH).
2. RST# must be at VSS ± 0.2 V to meet the maximum specified power-down current.
3. Refer to the Table 6, “Bus Cycle Definitions” on page 23 for valid DIN during a write operation.
4. WAIT is only valid during synchronous array read operations.
3.1.1
Read
The 1.8 Volt Intel Wireless Flash memory has several read configurations:
• Asynchronous page mode read.
• Synchronous burst mode read — outputs four, eight, sixteen, or continuous words, from main
blocks and parameter blocks.
Several read modes are available in each partition:
• Read-array mode: read accesses return flash array data from the addressed locations.
• Read identifier mode: reads return manufacturer and device identifier data, block lock status,
and protection register data. Identifier information can be accessed starting at 4-Mbit partition
base addresses; the flash array is not accessible in read identifier mode.
• Read query mode: reads return device CFI data. CFI information can be accessed starting at
4-Mbit partition base addresses; the flash array is not accessible in read query mode.
• Read status register mode: reads return status register data from the addressed partition. That
partition’s array data is not accessible. A system processor can check the status register to
determine an addressed partition’s state or monitor program and erase progress.
All partitions support the synchronous burst mode that internally sequences addresses with respect
to the input CLK to select and supply data to the outputs.
Identifier codes, query data, and status register read operations execute as single-synchronous or
asynchronous read cycles. WAIT is asserted during these reads.
18
Datasheet
Intel® Wireless Flash Memory (W18)
Access to the modes listed above is independent of VPP. An appropriate CUI command places the
device in a read mode. At initial power-up or after reset, the device defaults to asynchronous readarray mode.
Asserting CE# enables device read operations. The device internally decodes upper address inputs
to determine which partition is accessed. Asserting ADV# opens the internal address latches.
Asserting OE# activates the outputs and gates selected data onto the I/O bus. In asynchronous
mode, the address is latched when ADV# is deasserted (when the device is configured to use
ADV#). In synchronous mode, the address is latched by either the rising edge of ADV# or the
rising (or falling) CLK edge while ADV# remains asserted, whichever occurs first. WE# and RST#
must be at deasserted during read operations.
Note:
3.1.2
If only asynchronous reads are to be performed in your system, CLK should be tied to a valid VIH
level, WAIT signal can be floated and ADV# must be tied to ground.
Burst Suspend
The Burst Suspend feature allows the system to temporarily suspend a synchronous burst operation
if the system needs to use the flash address and data bus for other purposes. Burst accesses can be
suspended during the initial latency (before data is received) or after the device has output data.
When a burst access is suspended, internal array sensing continues and any previously latched
internal data is retained.
Burst Suspend occurs when CE# is asserted, the current address has been latched (either ADV#
rising edge or valid CLK edge), CLK is halted, and OE# is deasserted. CLK can be halted when it
is at VIH or VIL. To resume the burst access, OE# is reasserted and CLK is restarted. Subsequent
CLK edges resume the burst sequence where it left off.
Within the device, CE# gates WAIT. Therefore, during Burst Suspend WAIT remains asserted and
does not revert to a high-impedance state when OE# is deasserted. This can cause contention with
another device attempting to control the system’s READY signal during a Burst Suspend. System
using the Burst Suspend feature should not connect the device’s WAIT signal directly to the
system’s READY signal.
Refer to Figure 27, “Burst Suspend” on page 73.
3.1.3
Standby
De-asserting CE# deselects the device and places it in standby mode, substantially reducing device
power consumption. In standby mode, outputs are placed in a high-impedance state independent of
OE#. If deselected during a program or erase algorithm, the device shall consume active power
until the program or erase operation completes.
3.1.4
Reset
The device enters a reset mode when RST# is asserted. In reset mode, internal circuitry is turned
off and outputs are placed in a high-impedance state.
After returning from reset, a time tPHQV is required until outputs are valid, and a delay (tPHWV) is
required before a write sequence can be initiated. After this wake-up interval, normal operation is
restored. The device defaults to read-array mode, the status register is set to 80h, and the
configuration register defaults to asynchronous page-mode reads.
Datasheet
19
Intel® Wireless Flash Memory (W18)
If RST# is asserted during an erase or program operation, the operation aborts and the memory
contents at the aborted block or address are invalid. See Figure 33, “Reset Operations Waveforms”
on page 80 for detailed information regarding reset timings.
Like any automated device, it is important to assert RST# during system reset. When the system
comes out of reset, the processor expects to read from the flash memory array. Automated flash
memories provide status information when read during program or erase operations. If a CPU reset
occurs with no flash memory reset, proper CPU initialization may not occur because the flash
memory may be providing status information instead of array data. 1.8 Volt Intel Flash memories
allow proper CPU initialization following a system reset through the use of the RST# input. In this
application, RST# is controlled by the same CPU reset signal, RESET#.
3.1.5
Write
A write occurs when CE# and WE# are asserted and OE# is deasserted. Flash control commands
are written to the CUI using standard microprocessor write timings. Proper use of the ADV# input
is needed for proper latching of the addresses. Refer to Section 11.3, “AC Write Characteristics” on
page 74 for details. The address and data are latched on the rising edge of WE#. Write operations
are asynchronous; CLK is ignored (but still may be kept active/toggling).
The CUI does not occupy an addressable memory location within any partition. The system
processor must access it at the correct address range depending on the kind of command executed.
Programming or erasing may occur in only one partition at a time. Other partitions must be in one
of the read modes or erase suspend mode.
Table 5, “Command Codes and Descriptions” on page 21 shows the available commands.
Appendix A, “Write State Machine States” on page 83 provides information on moving between
different operating modes using CUI commands.
3.2
Device Commands
The device’s on-chip WSM manages erase and program algorithms. This local CPU (WSM)
controls the device’s in-system read, program, and erase operations. Bus cycles to or from the flash
memory conform to standard microprocessor bus cycles. RST#, CE#, OE#, WE#, and ADV#
control signals dictate data flow into and out of the device. WAIT informs the CPU of valid data
during burst reads. Table 4, “Bus Operations” on page 18 summarizes bus operations.
Device operations are selected by writing specific commands into the device’s CUI. Table 5,
“Command Codes and Descriptions” on page 21 lists all possible command codes and
descriptions. Table 6, “Bus Cycle Definitions” on page 23 lists command definitions. Because
commands are partition-specific, it is important to issue write commands within the target address
range.
20
Datasheet
Intel® Wireless Flash Memory (W18)
Table 5.
Operation
Command Codes and Descriptions (Sheet 1 of 2)
Code
Device
Command
Description
FFh
Read Array
Places selected partition in read-array mode.
70h
Read Status
Register
Places selected partition in status register read mode. The partition enters this
mode after a Program or Erase command is issued to it.
90h
Read Identifier
Puts the selected partition in read identifier mode. Device reads from partition
addresses output manufacturer/device codes, configuration register data, block
lock status, or protection register data on D[15:0].
98h
Read Query
Puts the addressed partition in read query mode. Device reads from the partition
addresses output CFI information on D[7:0].
50h
Clear Status
Register
The WSM can set the status register’s block lock (SR[1]), VPP (SR[3]), program
(SR[4]), and erase (SR[5]) status bits, but it cannot clear them. SR[5:3,1] can
only be cleared by a device reset or through the Clear Status Register command.
40h
Word Program
Setup
This preferred program command’s first cycle prepares the CUI for a program
operation. The second cycle latches address and data, and executes the WSM
program algorithm at this location. Status register updates occur when CE# or
OE# is toggled. A Read Array command is required to read array data after
programming.
10h
Alternate Setup
Equivalent to a Program Setup command (40h).
30h
EFP Setup
This program command activates EFP mode. The first write cycle sets up the
command. If the second cycle is an EFP Confirm command (D0h), subsequent
writes provide program data. All other commands are ignored after EFP mode
begins.
D0h
EFP Confirm
If the first command was EFP Setup (30h), the CUI latches the address and data,
and prepares the device for EFP mode.
20h
Erase Setup
This command prepares the CUI for Block Erase. The device erases the block
addressed by the Erase Confirm command. If the next command is not Erase
Confirm, the CUI sets status register bits SR[5:4] to indicate command sequence
error and places the partition in the read status register mode.
D0h
Erase Confirm
If the first command was Erase Setup (20h), the CUI latches address and data,
and erases the block indicated by the erase confirm cycle address. During
program or erase, the partition responds only to Read Status Register, Program
Suspend, and Erase Suspend commands. CE# or OE# toggle updates status
register data.
B0h
Program
Suspend or
Erase Suspend
This command, issued at any device address, suspends the currently executing
program or erase operation. Status register data indicates the operation was
successfully suspended if SR[2] (program suspend) or SR[6] (erase suspend)
and SR[7] are set. The WSM remains in the suspended state regardless of
control signal states (except RST#).
D0h
Suspend
Resume
This command, issued at any device address, resumes the suspended program
or erase operation.
60h
Lock Setup
This command prepares the CUI lock configuration. If the next command is not
Lock Block, Unlock Block, or Lock-Down, the CUI sets SR[5:4] to indicate
command sequence error.
01h
Lock Block
If the previous command was Lock Setup (60h), the CUI locks the addressed
block.
D0h
Unlock Block
If the previous command was Lock Setup (60h), the CUI latches the address and
unlocks the addressed block. If previously locked-down, the operation has no
effect.
2Fh
Lock-Down
If the previous command was Lock Setup (60h), the CUI latches the address and
locks-down the addressed block.
Read
Program
Erase
Suspend
Block Locking
Datasheet
21
Intel® Wireless Flash Memory (W18)
Table 5.
Command Codes and Descriptions (Sheet 2 of 2)
Device
Command
Operation
Code
Protection
C0h
Protection
Program
Setup
This command prepares the CUI for a protection register program operation. The
second cycle latches address and data, and starts the WSM’s protection register
program or lock algorithm. Toggling CE# or OE# updates the flash status register
data. To read array data after programming, issue a Read Array command.
60h
Configuration
Setup
This command prepares the CUI for device configuration. If Set Configuration
Register is not the next command, the CUI sets SR[5:4] to indicate command
sequence error.
03h
Set
Configuration
Register
If the previous command was Configuration Setup (60h), the CUI latches the
address and writes the data from A[15:0] into the configuration register.
Subsequent read operations access array data.
Description
Configuration
NOTE: Do not use unassigned commands. Intel reserves the right to redefine these codes for future functions.
22
Datasheet
Intel® Wireless Flash Memory (W18)
Table 6.
Bus Cycle Definitions
Operation
Read
Command
Lock
First Bus Cycle
Second Bus Cycle
Oper
Addr1
Data2,3
Oper
Addr1
Data2,3
Read Array/Reset
≥1
Write
PnA
FFh
Read
Read
Address
Array
Data
Read Identifier
≥2
Write
PnA
90h
Read
PBA+IA
IC
Read Query
≥2
Write
PnA
98h
Read
PBA+QA
QD
2
Write
PnA
70h
Read
PnA
SRD
Read Status Register
Program
and
Erase
Bus
Cycles
Clear Status Register
1
Write
XX
50h
Block Erase
2
Write
BA
20h
Write
BA
D0h
Word Program
2
Write
WA
40h/10h
Write
WA
WD
EFP
>2
Write
WA
30h
Write
WA
D0h
Program/Erase Suspend
1
Write
XX
B0h
Program/Erase Resume
1
Write
XX
D0h
Lock Block
2
Write
BA
60h
Write
BA
01h
Unlock Block
2
Write
BA
60h
Write
BA
D0h
Lock-Down Block
2
Write
BA
60h
Write
BA
2Fh
Protection Program
2
Write
PA
C0h
Write
PA
PD
Lock Protection Program
2
Write
LPA
C0h
Write
LPA
FFFDh
Set Configuration Register
2
Write
CD
60h
Write
CD
03h
Protection
Configuration
NOTES:
1. First-cycle command addresses should be the same as the operation’s target address. Examples: the first-cycle address for
the Read Identifier command should be the same as the Identification code address (IA); the first-cycle address for the Word
Program command should be the same as the word address (WA) to be programmed; the first-cycle address for the Erase/
Program Suspend command should be the same as the address within the block to be suspended; etc.
XX = Any valid address within the device.
IA = Identification code address.
BA = Block Address. Any address within a specific block.
LPA = Lock Protection Address is obtained from the CFI (through the Read Query command). The 1.8 Volt Intel Wireless
Flash memory family’s LPA is at 0080h.
PA = User programmable 4-word protection address.
PnA = Any address within a specific partition.
PBA = Partition Base Address. The very first address of a particular partition.
QA = Query code address.
WA = Word address of memory location to be written.
2. SRD = Status register data.
WD = Data to be written at location WA.
IC = Identifier code data.
PD = User programmable 4-word protection data.
QD = Query code data on D[7:0].
CD = Configuration register code data presented on device addresses A[15:0]. A[MAX:16] address bits can select any
partition. See Table 13, “Configuration Register Definitions” on page 47 for configuration register bits descriptions.
3. Commands other than those shown above are reserved by Intel for future device implementations and should not be used.
Datasheet
23
Intel® Wireless Flash Memory (W18)
3.3
Command Sequencing
When issuing a 2-cycle write sequence to the flash device, a read operation is allowed to occur
between the two write cycles. The setup phase of a 2-cycle write sequence places the addressed
partition into read-status mode, so if the same partition is read before the second “confirm” write
cycle is issued, status register data will be returned. Reads from other partitions, however, can
return actual array data assuming the addressed partition is already in read-array mode. Figure 3 on
page 24 and Figure 4 on page 24 illustrate these two conditions.
Figure 3. Normal Write and Read Cycles
Address [A]
Partition A
Partition A
Partition A
WE# [W]
OE# [G]
Data [Q]
20h
D0h
FFh
Block Erase Setup
Block Erase Conf irm
Read Array
Figure 4. Interleaving a 2-Cycle Write Sequence with an Array Read
Address [A]
Partition B
Partition A
Partition B
Partition A
WE# [W]
OE# [G]
Data [Q]
FFh
20h
Array Data
D0h
Read Array
Erase Setup
Bus Read
Erase Conf irm
By contrast, a write bus cycle may not interrupt a 2-cycle write sequence. Doing so causes a
command sequence error to appear in the status register. Figure 5 illustrates a command sequence
error.
Figure 5. Improper Command Sequencing
Address [A]
Partition X
Partitio n Y
Partition X
Partition X
WE# [W]
OE# [G]
Data [D/Q]
24
20h
FFh
D0h
SR Data
Datasheet
Intel® Wireless Flash Memory (W18)
4.0
Read Operations
4.1
Read Array
The Read Array command places (or resets) the partition in read-array mode and is used to read
data from the flash memory array. Upon initial device power-up, or after reset (RST# transitions
from VIL to VIH), all partitions default to asynchronous read-array mode. To read array data from
the flash device, first write the Read Array command (FFh) to the CUI and specify the desired
word address. Then read from that address. If a partition is already in read-array mode, issuing the
Read Array command is not required to read from that partition.
If the Read Array command is written to a partition that is erasing or programming, the device
presents invalid data on the bus until the program or erase operation completes. After the program
or erase finishes in that partition, valid array data can then be read. If an Erase Suspend or Program
Suspend command suspends the WSM, a subsequent Read Array command places the addressed
partition in read-array mode. The Read Array command functions independently of VPP.
4.2
Read Device ID
The read identifier mode outputs the manufacturer/device identifier, block lock status, protection
register codes, and configuration register data. The identifier information is contained within a
separate memory space on the device and can be accessed along the 4-Mbit partition address range
supplied by the Read Identifier command (90h) address. Reads from addresses in Table 7 retrieve
ID information. Issuing a Read Identifier command to a partition that is programming or erasing
places that partition’s outputs in read ID mode while the partition continues to program or erase in
the background.
Table 7.
Device Identification Codes (Sheet 1 of 2)
Address1
Item
Manufacturer ID
Device ID
Block Lock Status(2)
Block Lock-Down Status(2)
Configuration Register
Datasheet
Data
Base
Offset
Partition
00h
Partition
Block
Block
Partition
Description
0089h
8862h
32-Mbit TPD
8863h
32-Mbit BPD
8864h
64-Mbit TPD
8865h
64-Mbit BPD
8866h
128-Mbit TPD
8867h
128-Mbit BPD
D0 = 0
Block is unlocked
01h
02h
D0 = 1
Block is locked
D1 = 0
Block is not locked-down
D1 = 1
Block is locked down
02h
05h
Register Data
25
Intel® Wireless Flash Memory (W18)
Table 7.
Device Identification Codes (Sheet 2 of 2)
Address1
Item
Data
Base
Offset
Protection Register Lock Status
Partition
80h
Lock Data
Protection Register
Partition
81h - 88h
Register Data
Description
Multiple reads required to read
the entire 128-bit Protection
Register.
NOTES:
1. The address is constructed from a base address plus an offset. For example, to read the Block Lock Status
for block number 38 in a BPD, set the address to the BBA (0F8000h) plus the offset (02h), i.e. 0F8002h.
Then examine bit 0 of the data to determine if the block is locked.
2. See Section 7.1.4, “Block Lock Status” on page 41 for valid lock status.
4.3
Read Query (CFI)
This device contains a separate CFI query database that acts as an “on-chip datasheet.” The CFI
information within this device can be accessed by issuing the Read Query command and supplying
a specific address. The address is constructed from the base address of a partition plus a particular
offset corresponding to the desired CFI field. Appendix B, “Common Flash Interface” on page 86
shows accessible CFI fields and their address offsets. Issuing the Read Query command to a
partition that is programming or erasing puts that partition in read query mode while the partition
continues to program or erase in the background.
4.4
Read Status Register
The device’s status register displays program and erase operation status. A partition’s status can be
read after writing the Read Status Register command to any location within the partition’s address
range. Read-status mode is the default read mode following a Program, Erase, or Lock Block
command sequence. Subsequent single reads from that partition will return its status until another
valid command is written.
The read-status mode supports single synchronous and single asynchronous reads only; it doesn’t
support burst reads. The first falling edge of OE# or CE# latches and updates status register data.
The operation doesn’t affect other partitions’ modes. Because the status register is 8 bits wide, only
DQ [7:0] contains valid status register data; DQ [15:8] contains zeros. See Table 8, “Status
Register Definitions” on page 27 and Table 9, “Status Register Descriptions” on page 27.
Each 4-Mbit partition contains its own status register. Bits SR[6:0] are unique to each partition, but
SR[7], the Device WSM Status (DWS) bit, pertains to the entire device. SR[7] provides program
and erase status of the entire device. By contrast, the Partition WSM Status (PWS) bit, SR[0],
provides program and erase status of the addressed partition only. Status register bits SR[6:1]
present information about partition-specific program, erase, suspend, VPP, and block-lock states.
Table 10, “Status Register Device WSM and Partition Write Status Description” on page 27
presents descriptions of DWS (SR[7]) and PWS (SR[0]) combinations.
26
Datasheet
Intel® Wireless Flash Memory (W18)
Table 8.
Status Register Definitions
DWS
ESS
ES
PS
VPPS
PSS
DPS
PWS
7
6
5
4
3
2
1
0
Table 9.
Bit
Status Register Descriptions
Name
State
DWS
7
0 = Device WSM is Busy
Device WSM Status
ESS
6
0 = Erase in progress/completed
Erase Suspend Status
1 = Erase suspended
ES
0 = Erase successful
5
Erase Status
1 = Erase error
PS
4
0 = Program successful
Program Status
1 = VPP low detect, operation aborted
VPP Status
PSS
0 = Program in progress/completed
Program Suspend
Status
Device Protect Status
1 = Aborted erase/program attempt on
locked block
0 = This partition is busy, but only if
SR[7]=0
PWS
0
1 = Program suspended
0 = Unlocked
DPS
1
1 = Program error
0 = VPP OK
VPPS
3
2
1 = Device WSM is Ready
Partition Write Status
1 = Another partition is busy, but only if
SR[7]=0
Description
SR[7] indicates erase or program completion in the
device. SR[6:1] are invalid while SR[7] = 0. See Table
10 for valid SR[7] and SR[0] combinations.
After issuing an Erase Suspend command, the WSM
halts and sets SR[7] and SR[6]. SR[6] remains set until
the device receives an Erase Resume command.
SR[5] is set if an attempted erase failed. A Command
Sequence Error is indicated when SR[7,5:4] are set.
SR[4] is set if the WSM failed to program a word.
The WSM indicates the VPP level after program or
erase completes. SR[3] does not provide continuous
VPP feedback and isn’t guaranteed when VPP ≠ VPP1/2.
After receiving a Program Suspend command, the
WSM halts execution and sets SR[7] and SR[2]. They
remain set until a Resume command is received.
If an erase or program operation is attempted to a
locked block (if WP# = VIL), the WSM sets SR[1] and
aborts the operation.
Addressed partition is erasing or programming. In EFP
mode, SR[0] indicates that a data-stream word has
finished programming or verifying depending on the
particular EFP phase. See Table 10 for valid SR[7] and
SR[0] combinations.
Table 10. Status Register Device WSM and Partition Write Status Description
DWS
(SR[7])
PWS
(SR[0])
0
0
0
1
1
0
Description
The addressed partition is performing a program/erase operation.
EFP: device has finished programming or verifying data, or is ready for data.
A partition other than the one currently addressed is performing a program/erase operation.
EFP: the device is either programming or verifying data.
No program/erase operation is in progress in any partition. Erase and Program suspend bits (SR[6,2])
indicate whether other partitions are suspended.
EFP: the device has exited EFP mode.
1
Datasheet
1
Won’t occur in standard program or erase modes.
EFP: this combination does not occur.
27
Intel® Wireless Flash Memory (W18)
4.5
Clear Status Register
The Clear Status Register command clears the status register and leaves all partition output states
unchanged. The WSM can set all status register bits and clear bits SR[7:6,2,0]. Because bits
SR[5,4,3,1] indicate various error conditions, they can only be cleared by the Clear Status Register
command. By allowing system software to reset these bits, several operations (such as
cumulatively programming several addresses or erasing multiple blocks in sequence) can be
performed before reading the status register to determine error occurrence. If an error is detected,
the Status Register must be cleared before beginning another command or sequence. Device reset
(RST# = VIL) also clears the status register. This command functions independently of VPP.
5.0
Program Operations
5.1
Word Program
When the Word Program command is issued, the WSM executes a sequence of internally timed
events to program a word at the desired address and verify that the bits are sufficiently
programmed. Programming the flash array changes specifically addressed bits to 0; 1 bits do not
change the memory cell contents.
Programming can occur in only one partition at a time. All other partitions must be in either a read
mode or erase suspend mode. Only one partition can be in erase suspend mode at a time.
The status register can be examined for program progress by reading any address within the
partition that is busy programming. However, while most status register bits are partition-specific,
the Device WSM Status bit, SR[7], is device-specific; that is, if the status register is read from any
other partition, SR[7] indicates program status of the entire device. This permits the system CPU to
monitor program progress while reading the status of other partitions.
CE# or OE# toggle (during polling) updates the status register. Several commands can be issued to
a partition that is programming: Read Status Register, Program Suspend, Read Identifier, and Read
Query. The Read Array command can also be issued, but the read data is indeterminate.
After programming completes, three status register bits can signify various possible error
conditions. SR[4] indicates a program failure if set. If SR[3] is set, the WSM couldn’t execute the
Word Program command because VPP was outside acceptable limits. If SR[1] is set, the program
was aborted because the WSM attempted to program a locked block.
After the status register data is examined, clear it with the Clear Status Register command before a
new command is issued. The partition remains in status register mode until another command is
written to that partition. Any command can be issued after the status register indicates program
completion.
If CE# is deasserted while the device is programming, the devices will not enter standby mode until
the program operation completes.
28
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 6. Word Program Flowchart
WORD PROGRAM PROCEDURE
Bus
Command
Operation
Start
Write
Write 40h,
Word Address
Write
Program Data = 40h
Setup
Addr = Location to program (WA)
Data
Write Data
Word Address
Read
Suspend
Program
Loop
Read Status
Register
Standby
No
SR[7] =
0
Suspend
Program
Comments
Data = Data to program (WD)
Addr = Location to program (WA)
Read SRD
Toggle CE# or OE# to update SRD
Check SR[7]
1 = WSM ready
0 = WSM busy
Yes
Repeat for subsequent programming operations.
1
Full status register check can be done after each program or
after a sequence of program operations.
Full Program
Status Check
(if desired)
Program
Complete
FULL PROGRAM STATUS CHECK PROCEDURE
Read Status
Register
SR[3] =
Bus
Command
Operation
1
SR[4] =
Standby
Check SR[3]
1 = VPP error
Standby
Check SR[4]
1 = Data program error
Standby
Check SR[1]
1 = Attempted program to locked block
Program aborted
VPP Range
Error
0
1
Program
Error
1
Device
Protect Error
Comments
0
SR[1] =
0
Program
Successful
5.2
SR[3] MUST be cleared before the WSM will allow further
program attempts
Only the Clear Staus Register command clears SR[4:3,1].
If an error is detected, clear the status register before
attempting a program retry or other error recovery.
Factory Programming
The standard factory programming mode uses the same commands and algorithm as the Word
Program mode (40h/10h). When VPP is at VPP1, program and erase currents are drawn through
VCC. If VPP is driven by a logic signal, VPP1 must remain above the VPP1Min value to perform insystem flash modifications. When VPP is connected to a 12 V power supply, the device draws
program and erase current directly from VPP. This eliminates the need for an external switching
transistor to control the VPP voltage. Figure 15, “Examples of VPP Power Supply Configurations”
on page 45 shows examples of flash power supply usage in various configurations.
Datasheet
29
Intel® Wireless Flash Memory (W18)
The 12-V VPP mode enhances programming performance during the short time period typically
found in manufacturing processes; however, it is not intended for extended use.12 V may be
applied to VPP during program and erase operations as specified in Section 10.2, “Operating
Conditions” on page 57. VPP may be connected to 12 V for a total of tPPH hours maximum.
Stressing the device beyond these limits may cause permanent damage.
5.3
Enhanced Factory Program (EFP)
EFP substantially improves device programming performance through a number of enhancements
to the conventional 12 Volt word program algorithm. EFP's more efficient WSM algorithm
eliminates the traditional overhead delays of the conventional word program mode in both the host
programming system and the flash device. Changes to the conventional word programming
flowchart and internal WSM routine were developed because of today's beat-rate-sensitive
manufacturing environments; a balance between programming speed and cycling performance was
attained.
The host programmer writes data to the device and checks the Status Register to determine when
the data has completed programming. This modification essentially cuts write bus cycles in half.
Following each internal program pulse, the WSM increments the device's address to the next
physical location. Now, programming equipment can sequentially stream program data throughout
an entire block without having to setup and present each new address. In combination, these
enhancements reduce much of the host programmer overhead, enabling more of a data streaming
approach to device programming.
EFP further speeds up programming by performing internal code verification. With this, PROM
programmers can rely on the device to verify that it has been programmed properly. From the
device side, EFP streamlines internal overhead by eliminating the delays previously associated to
switch voltages between programming and verify levels at each memory-word location.
EFP consists of four phases: setup, program, verify and exit. Refer to Figure 7, “Enhanced Factory
Program Flowchart” on page 33 for a detailed graphical representation of how to implement EFP.
5.3.1
EFP Requirements and Considerations
Ambient temperature: TA = 25 °C ±5 °C
VCC within specified operating range
EFP Requirements
VPP within specified VPP2 range
Target block unlocked
Block cycling below 100 erase cycles 1
RWW not supported2
EFP Considerations
EFP programs one block at a time
EFP cannot be suspended
NOTES:
1. Recommended for optimum performance. Some degradation in performance may
occur if this limit is exceeded, but the internal algorithm will continue to work properly.
2. Code or data cannot be read from another partition during EFP.
30
Datasheet
Intel® Wireless Flash Memory (W18)
5.3.2
Setup
After receiving the EFP Setup (30h) and EFP Confirm (D0h) command sequence, SR[7] transitions
from a 1 to a 0 indicating that the WSM is busy with EFP algorithm startup. A delay before
checking SR[7] is required to allow the WSM time to perform all of its setups and checks (VPP
level and block lock status). If an error is detected, status register bits SR[4], SR[3], and/or SR[1]
are set and EFP operation terminates.
Note:
5.3.3
After the EFP Setup and Confirm command sequence, reads from the device automatically output
status register data. Do not issue the Read Status Register command; it will be interpreted as data to
program at WA0.
Program
After setup completion, the host programming system must check SR[0] to determine “data-stream
ready" status (SR[0]=0). Each subsequent write after this is a program-data write to the flash array.
Each cell within the memory word to be programmed to 0 receives one WSM pulse; additional
pulses, if required, occur in the verify phase. SR[0]=1 indicates that the WSM is busy applying the
program pulse.
The host programmer must poll the device's status register for the "program done" state after each
data-stream write. SR[0]=0 indicates that the appropriate cell(s) within the accessed memory
location have received their single WSM program pulse, and that the device is now ready for the
next word. Although the host may check full status for errors at any time, it is only necessary on a
block basis, after EFP exit.
Addresses must remain within the target block. Supplying an address outside the target block
immediately terminates the program phase; the WSM then enters the EFP verify phase.
The address can either hold constant or it can increment. The device compares the incoming
address to that stored from the setup phase (WA0); if they match, the WSM programs the new data
word at the next sequential memory location. If they differ, the WSM jumps to the new address
location.
The program phase concludes when the host programming system writes to a different block
address, and data supplied must be FFFFh. Upon program phase completion, the device enters the
EFP verify phase.
5.3.4
Verify
A high percentage of the flash bits program on the first WSM pulse. However, for those cells that
do not completely program on their first attempt, EFP internal verification identifies them and
applies additional pulses as required.
The verify phase is identical in flow to the program phase, except that instead of programming
incoming data, the WSM compares the verify-stream data to that which was previously
programmed into the block. If the data compares correctly, the host programmer proceeds to the
next word. If not, the host waits while the WSM applies an additional pulse(s).
The host programmer must reset its initial verify-word address to the same starting location
supplied during the program phase. It then reissues each data word in the same order as during the
program phase. Like programming, the host may write each subsequent data word to WA0 or it may
increment up through the block addresses.
Datasheet
31
Intel® Wireless Flash Memory (W18)
The verification phase concludes when the interfacing programmer writes to a different block
address; data supplied must be FFFFh. Upon completion of the verify phase, the device enters the
EFP exit phase.
5.3.5
Exit
SR[7]=1 indicates that the device has returned to normal operating conditions. A full status check
should be performed at this time to ensure the entire block programmed successfully. After EFP
exit, any valid CUI command can be issued.
32
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 7. Enhanced Factory Program Flowchart
ENHANCED FACTORY PROGRAMMING PROCEDURE
EFP Setup
EFP Program
EFP Verify
EFP Exit
Start
Read
Status Register
Read
Status Register
Read
Status Register
SR[0]=1=N
Write 30h
Address = WA0
SR[0]=1=N
Write D0h
Address = WA0
Read
Status Register
EFP Setup
Done?
SR[7]=0=Y
EFP setup time
N
SR[0]=1=N Verify Stream
Ready?
Data Stream
Ready?
Check VPP & Lock
errors (SR[3,1])
EFP
Exited?
SR[0] =0=Y
SR[7]=1=Y
Write Data
Address = WA0
Write Data
Address = WA0
Full Status Check
Procedure
Read
Status Register
Read
Status Register
Operation
Complete
Program
Done?
Verify
Done?
SR[0]=0=Y
SR[0]=0=Y
N
Last
Data?
Last
Data?
Y
SR[7]=1=N
SR[7]=0=N
SR[0] =0=Y
SR[0]=1=N
VPP = 12V
Unlock Block
Y
Write FFFFh
Address ≠ BBA
Write FFFFh
Address ≠ BBA
Exit
EFP Setup
Bus
State
Comments
EFP Program
Bus
State
Read
Write
Unlock
Block
VPP = 12V
Unlock block
Write
EFP
Setup
Data = 30h
Address = WA0
Standby
EFP
Data = D0h
Confirm Address = WA0
Write
(note 1)
Write
Standby
EFP setup time
Read
Standby
EFP
Setup
Done?
Status Register
Check SR[7]
0 = EFP ready
1 = EFP not ready
If SR[7] = 1:
Error
Check SR[3,1]
Standby Condition
SR[3] = 1 = VPP error
Check
SR[1] = 1 = locked block
Comments
Status Register
Status Register
Data
Check SR[0]
Stream 0 = Ready for data
Ready? 1 = Not ready for data
Standby
Verify Check SR[0]
Stream 0 = Ready for verify
Ready? 1 = Not ready for verify
Data = Data to program
Address = WA0
Write
(note 2)
Status Register
Check SR[0]
Program
Standby
0 = Program done
Done?
1 = Program not done
Write
Comments
Read
Read
Standby
EFP Verify
Bus
State
Last
Data?
Device automatically
increments address.
Exit
Data = FFFFh
Program Address not within same
Phase BBA
Data = Word to verify
Address = WA0
Read
Status Register
Standby
(note 3)
Verify
Done?
Check SR[0]
0 = Verify done
1 = Verify not done
Standby
Last
Data?
Device automatically
increments address.
Write
Exit
Verify
Phase
Data = FFFFh
Address not within same
BBA
EFP Exit
1. WA0 = first Word Address to be programmed within the target block. The BBA (Block Base
Address) must remain constant throughout the program phase data stream; WA can be held
constant at the first address location, or it can be written to sequence up through the addresses
within the block. Writing to a BBA not equal to that of the block currently being written to
terminates the EFP program phase, and instructs the device to enter the EFP verify phase.
2. For proper verification to occur , the verify data stream must be presented to the device in the
same sequence as that of the program phase data stream. Writing to a BBA not equal to WA
terminates the EFP verify phase, and instructs the device to exit EFP .
3. Bits that did not fully program with the single WSM pulse of the EFP program phase receive
additional program-pulse attempts during the EFP verify phase. The device will report any
program failure by setting SR[4]=1; this check can be performed during the full status check after
EFP has been exited for that block, and will indicate any error within the entire data stream.
Datasheet
Read
Standby
Status Register
Check SR[7]
EFP
0 = Exit not finished
Exited?
1 = Exit completed
Repeat for subsequent operations.
After EFP exit, a Full Status Check can
determine if any program error occurred.
See the Full Status Check procedure in the
Word Program flowchart.
33
Intel® Wireless Flash Memory (W18)
6.0
Program and Erase Operations
6.1
Program/Erase Suspend and Resume
The Program Suspend and Erase Suspend commands halt an in-progress program or erase
operation. The command can be issued at any device address. The partition corresponding to the
command’s address remains in its previous state. A suspend command allows data to be accessed
from memory locations other than the one being programmed or the block being erased.
A program operation can be suspended only to perform a read operation. An erase operation can be
suspended to perform either a program or a read operation within any block, except the block that
is erase suspended. A program command nested within a suspended erase can subsequently be
suspended to read yet another location. Once a program or erase process starts, the Suspend
command requests that the WSM suspend the program or erase sequence at predetermined points
in the algorithm. The partition that is actually suspended continues to output status register data
after the Suspend command is written. An operation is suspended when status bits SR[7] and SR[6]
and/or SR[2] are set.
To read data from blocks within the partition (other than an erase-suspended block), you can write
a Read Array command. Block erase cannot resume until the program operations initiated during
erase suspend are complete. Read Array, Read Status Register, Read Identifier (ID), Read Query,
and Program Resume are valid commands during Program or Erase Suspend. Additionally, Clear
Status Register, Program, Program Suspend, Erase Resume, Lock Block, Unlock Block, and LockDown Block are valid commands during erase suspend.
To read data from a block in a partition that is not programming or erasing, the operation does not
need to be suspended. If the other partition is already in read array, ID, or Query mode, issuing a
valid address returns corresponding data. If the other partition is not in a read mode, one of the read
commands must be issued to the partition before data can be read.
During a suspend, CE# = VIH places the device in standby state, which reduces active current. VPP
must remain at its program level and WP# must remain unchanged while in suspend mode.
A resume command instructs the WSM to continue programming or erasing and clears status
register bits SR[2] (or SR[6]) and SR[7]. The Resume command can be written to any partition.
When read at the partition that is programming or erasing, the device outputs data corresponding to
the partition’s last mode. If status register error bits are set, the status register can be cleared before
issuing the next instruction. RST# must remain at VIH. See Figure 8, “Program Suspend / Resume
Flowchart” on page 35, and Figure 9, “Erase Suspend / Resume Flowchart” on page 36.
If a suspended partition was placed in read array, read status register, read identifier (ID), or read
query mode during the suspend, the device remains in that mode and outputs data corresponding to
that mode after the program or erase operation is resumed. After resuming a suspended operation,
issue the read command appropriate to the read operation. To read status after resuming a
suspended operation, issue a Read Status Register command (70h) to return the suspended partition
to status mode.
34
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 8. Program Suspend / Resume Flowchart
PROGRAM SUSPEND / RESUME PROCEDURE
Bus
Command
Operation
Start
Program Suspend
Write
Write B0h
Any Address
Read
Write
Status
Write 70h
Same Partition
SR.7 =
Program Data = B0h
Suspend Addr = Block to suspend (BA)
Read
Status
0
Standby
Check SR.7
1 = WSM ready
0 = WSM busy
Standby
Check SR.2
1 = Program suspended
0 = Program completed
1
SR.2 =
0
Program
Completed
1
Read
Write
Array
Write FFh
Susp Partition
Read
Array
Done
Reading
Yes
Program Resume
Program Data = D0h
Resume Addr = Suspended block (BA)
If the suspended partition was placed in Read Array mode:
No
Write
Read
Array
Write D0h
Any Address
Write FFh
Pgm'd Partition
Program
Resumed
Read Array
Data
Read
Read
Status
Return partition to Status mode:
Data = 70h
Addr = Same partition
Status
Write 70h
Same Partition
Datasheet
Write
Data = FFh
Addr = Any address within the
suspended partition
Read array data from block other than
the one being programmed
Read
Read Array
Data
Data = 70h
Addr = Same partition
Status register data
Toggle CE# or OE# to update Status
register
Addr = Suspended block (BA)
Read
Read Status
Register
Comments
PGM_SUS.WMF
35
Intel® Wireless Flash Memory (W18)
Figure 9. Erase Suspend / Resume Flowchart
ERASE SUSPEND / RESUME PROCEDURE
Bus
Command
Operation
Start
Erase
Suspend
Write
Write B0h
Any Address
Read
Write
Status
Write 70h
Same Partition
Erase
Data = B0h
Suspend Addr = Any address
Read
Status
Read Status
Register
SR.6 =
Read or
Program?
Read Array
Data
No
Check SR.7
1 = WSM ready
0 = WSM busy
Standby
Check SR.6
1 = Erase suspended
0 = Erase completed
Erase
Completed
0
Write
1
Read
Standby
0
1
Program
Loop
Write
Yes
Resume
Array
Write FFh
Erased Partition
Erase Resumed
Read Array
Data
Program Data = D0h
Resume Addr = Any address
Write
Read
Status
Return partition to Status mode:
Data = 70h
Addr = Same partition
Status
Write 70h
Same Partition
6.2
Read
Write D0h
Any Address
Read
Read array or program data from/to
block other than the one being erased
If the suspended partition was placed in
Read Array mode or a Program Loop:
Done?
Erase
Read Array Data = FFh or 40h
or Program Addr = Block to program or read
Read or
Write
Program
Data = 70h
Addr = Same partition
Status register data. Toggle CE# or
OE# to update Status register
Addr = Same partition
Read
SR.7 =
Comments
ERAS_SUS.WMF
Block Erase
The 2-cycle block erase command sequence, consisting of Erase Setup (20h) and Erase Confirm
(D0h), initiates one block erase at the addressed block. Only one partition can be in an erase mode
at a time; other partitions must be in a read mode. The Erase Confirm command internally latches
the address of the block to be erased. Erase forces all bits within the block to 1. SR[7] is cleared
while the erase executes.
36
Datasheet
Intel® Wireless Flash Memory (W18)
After writing the Erase Confirm command, the selected partition is placed in read status register
mode and reads performed to that partition return the current status data. The address given during
the Erase Confirm command does not need to be the same address used in the Erase Setup
command. So, if the Erase Confirm command is given to partition B, then the selected block in
partition B will be erased even if the Erase Setup command was to partition A.
The 2-cycle erase sequence cannot be interrupted with a bus write operation. For example, an Erase
Setup command must be immediately followed by the Erase Confirm command in order to execute
properly. If a different command is issued between the setup and confirm commands, the partition
is placed in read-status mode, the status register signals a command sequence error, and all
subsequent erase commands to that partition are ignored until the status register is cleared.
The CPU can detect block erase completion by analyzing SR[7] of that partition. If an error bit
(SR[5,3,1]) was flagged, the status register can be cleared by issuing the Clear Status Register
command before attempting the next operation. The partition remains in read-status mode until
another command is written to its CUI. Any CUI instruction can follow after erasing completes.
The CUI can be set to read-array mode to prevent inadvertent status register reads.
Datasheet
37
Intel® Wireless Flash Memory (W18)
Figure 10. Block Erase Flowchart
BLOCK ERASE PROCEDURE
Bus
Command
Comments
Operation
Block
Data = 20h
Write
Erase
Addr = Block to be erased (BA)
Setup
Start
Write 20h
Block Address
Write
Write D0h and
Block Address
Erase
Confirm
Read
Suspend
Erase
Loop
Read Status
Register
No
SR[7] =
0
Suspend
Erase
Standby
Data = D0h
Addr = Block to be erased (BA)
Read SRD
Toggle CE# or OE# to update SRD
Check SR[7]
1 = WSM ready
0 = WSM busy
Yes
Repeat for subsequent block erasures.
1
Full status register check can be done after each block erase
or after a sequence of block erasures.
Full Erase
Status Check
(if desired)
Block Erase
Complete
FULL ERASE STATUS CHECK PROCEDURE
Read Status
Register
SR[3] =
Bus
Command
Operation
1
SR[5:4] =
Standby
Check SR[3]
1 = VPP error
Standby
Check SR[5:4]
Both 1 = Command sequence error
Standby
Check SR[5]
1 = Block erase error
Standby
Check SR[1]
1 = Attempted erase of locked block
Erase aborted
VPP Range
Error
0
1
Command
Sequence Error
1
Block Erase
Error
Comments
0
SR[5] =
0
SR[1] =
0
Block Erase
Successful
6.3
1
Erase of
Locked Block
Aborted
SR[3,1] must be cleared before the WSM will allow further
erase attempts.
Only the Clear Status Register command clears SR[5:3,1].
If an error is detected, clear the Status register before
attempting an erase retry or other error recovery.
Read-While-Write and Read-While-Erase
The 1.8 Volt Intel® Wireless Flash memory supports flexible multi-partition dual-operation
architecture. By dividing the flash memory into many separate partitions, the device can read from
one partition while programing or erasing in another partition; hence the terms, RWW and RWE.
Both of these features greatly enhance data storage performance.
38
Datasheet
Intel® Wireless Flash Memory (W18)
The product does not support simultaneous program and erase operations. Attempting to perform
operations such as these results in a command sequence error. Only one partition can be
programming or erasing while another partition is reading. However, one partition may be in erase
suspend mode while a second partition is performing a program operation, and yet another partition
is executing a read command. Table 5, “Command Codes and Descriptions” on page 21 describes
the command codes available for all functions.
7.0
Security Modes
The 1.8 Volt Intel Wireless Flash memory offers both hardware and software security features to
protect the flash data. The software security feature is used by executing the Lock Block command.
The hardware security feature is used by executing the Lock-Down Block command and by
asserting the WP# signal.
Refer to Figure 11, “Block Locking State Diagram” on page 40 for a state diagram of the flash
security features. Also see Figure 12, “Locking Operations Flowchart” on page 42.
7.1
Block Lock Operations
Individual instant block locking protects code and data by allowing any block to be locked or
unlocked with no latency. This locking scheme offers two levels of protection. The first allows
software-only control of block locking (useful for frequently changed data blocks), while the
second requires hardware interaction before locking can be changed (protects infrequently changed
code blocks).
The following sections discuss the locking system operation. The term “state [abc]” specifies
locking states; for example, “state [001],” where a = WP# value, b = block lock-down status bit
D1, and c = Block Lock status register bit D0. Figure 11, “Block Locking State Diagram” on
page 40 defines possible locking states.
The following summarizes the locking functionality.
• All blocks power-up in a locked state.
• Unlock commands can unlock these blocks, and lock commands can lock them again.
• The Lock-Down command locks a block and prevents it from being unlocked when WP# is
asserted.
— Locked-down blocks can be unlocked or locked with commands as long as WP# is
deasserted
— The lock-down status bit is cleared only when the device is reset or powered-down.
Block lock registers are not affected by the VPP level. They may be modified and read even if VPP
VPPLK.
≤
Each block’s locking status can be set to locked, unlocked, and lock-down, as described in the
following sections. See Figure 12, “Locking Operations Flowchart” on page 42.
Datasheet
39
Intel® Wireless Flash Memory (W18)
Figure 11. Block Locking State Diagram
Power-Up/Reset
Locked
[X01]
LockedDown4,5
[011]
Hardware
Locked5
[011]
WP# Hardware Control
Unlocked
[X00]
Software
Locked
[111]
Unlocked
[110]
Software Block Lock (0x60/0x01) or Software Block Unlock (0x60/0xD0)
Software Block Lock-Down (0x60/0x2F)
WP# hardware control
Notes:
7.1.1
1. [a,b,c] represents [WP#, D1, D0]. X = Don’t Care.
2. D1 indicates block Lock-down status. D1 = ‘0’, Lock-down has not been issued to
this block. D1 = ‘1’, Lock-down has been issued to this block.
3. D0 indicates block lock status. D0 = ‘0’, block is unlocked. D0 = ‘1’, block is locked.
4. Locked-down = Hardware + Software locked.
5. [011] states should be tracked by system software to determine difference between
Hardware Locked and Locked-Down states.
Lock
All blocks default to locked (state [x01]) after initial power-up or reset. Locked blocks are fully
protected from alteration. Attempted program or erase operations to a locked block will return an
error in SR[1]. Unlocked blocks can be locked by using the Lock Block command sequence.
Similarly, a locked block’s status can be changed to unlocked or lock-down using the appropriate
software commands.
7.1.2
Unlock
Unlocked blocks (states [x00] and [110]) can be programmed or erased. All unlocked blocks return
to the locked state when the device is reset or powered-down. An unlocked block’s status can be
changed to the locked or locked-down state using the appropriate software commands. A locked
block can be unlocked by writing the Unlock Block command sequence if the block is not lockeddown.
7.1.3
Lock-Down
Locked-down blocks (state [011]) offer the user an additional level of write protection beyond that
of a regular locked block. A block that is locked-down cannot have it’s state changed by software if
WP# is asserted. A locked or unlocked block can be locked-down by writing the Lock-Down Block
command sequence. If a block was set to locked-down, then later changed to unlocked, a Lock-
40
Datasheet
Intel® Wireless Flash Memory (W18)
Down command should be issued prior asserting WP# will put that block back to the locked-down
state. When WP# is deasserted, locked-down blocks are changed to the locked state and can then
be unlocked by the Unlock Block command.
7.1.4
Block Lock Status
Every block’s lock status can be read in read identifier mode. To enter this mode, issue the Read
Identifier command to the device. Subsequent reads at Block Base Address + 02h will output that
block’s lock status. For example, to read the block lock status of block 10, the address sent to the
device should be 50002h (for a top-parameter device). The lowest two data bits of the read data, D1
and D0, represent the lock status. D0 indicates the block lock status. It is set by the Lock Block
command and cleared by the Block Unlock command. It is also set when entering the lock-down
state. D1 indicates lock-down status and is set by the Lock-Down command. The lock-down status
bit cannot be cleared by software–only by device reset or power-down. See Table 11.
Table 11. Write Protection Truth Table
7.1.5
VPP
WP#
RST#
Write Protection
X
X
VIL
Device inaccessible
VIL
X
VIH
Word program and block erase prohibited
X
VIL
VIH
All lock-down blocks locked
X
VIH
VIH
All lock-down blocks can be unlocked
Lock During Erase Suspend
Block lock configurations can be performed during an erase suspend operation by using the
standard locking command sequences to unlock, lock, or lock-down a block. This feature is useful
when another block requires immediate updating.
To change block locking during an erase operation, first write the Erase Suspend command. After
checking SR[6] to determine the erase operation has suspended, write the desired lock command
sequence to a block; the lock status will be changed. After completing lock, unlock, read, or
program operations, resume the erase operation with the Erase Resume command (D0h).
If a block is locked or locked-down during a suspended erase of the same block, the locking status
bits change immediately. When the erase operation is resumed, it will complete normally.
Locking operations cannot occur during program suspend. Appendix A, “Write State Machine
States” on page 83 shows valid commands during erase suspend.
7.1.6
Status Register Error Checking
Using nested locking or program command sequences during erase suspend can introduce
ambiguity into status register results.
Because locking changes require 2-cycle command sequences, for example, 60h followed by 01h
to lock a block, following the Configuration Setup command (60h) with an invalid command
produces a command sequence error (SR[5:4]=11b). If a Lock Block command error occurs during
erase suspend, the device sets SR[4] and SR[5] to 1 even after the erase is resumed. When erase is
Datasheet
41
Intel® Wireless Flash Memory (W18)
complete, possible errors during the erase cannot be detected from the status register because of the
previous locking command error. A similar situation occurs if a program operation error is nested
within an erase suspend.
7.1.7
WP# Lock-Down Control
The Write Protect signal, WP#, adds an additional layer of block security. WP# only affects blocks
that once had the Lock-Down command written to them. After the lock-down status bit is set for a
block, asserting WP# forces that block into the lock-down state [011] and prevents it from being
unlocked. After WP# is deasserted, the block’s state reverts to locked [111] and software
commands can then unlock the block (for erase or program operations) and subsequently re-lock it.
Only device reset or power-down can clear the lock-down status bit and render WP# ineffective.
Figure 12. Locking Operations Flowchart
LOCKING OPERATIONS PROCEDURE
Start
Bus
Command
Operation
Write 60h
Block Address
Write
Write 01,D0,2Fh
Block Address
Write
Optional
Write 90h
BBA + 02h
Write
(Optional)
Read Block Lock
Status
Locking
Change?
Lock
Setup
Comments
Data = 60h
Addr = Block to lock/unlock/lock-down (BA)
Lock,
Data = 01h (Lock block)
Unlock, or
D0h (Unlock block)
Lockdown
2Fh (Lockdown block)
Confirm Addr = Block to lock/unlock/lock-down (BA)
Read ID
Plane
Data = 90h
Addr = BBA + 02h
Read
Block Lock Block Lock status data
(Optional)
Status Addr = BBA + 02h
No
Confirm locking change on DQ[1:0].
(See Block Locking State Transitions Table
for valid combinations.)
Standby
(Optional)
Yes
Write FFh
Partition Address
Write
Read
Array
Data = FFh
Addr = Any address in same partition
Lock Change
Complete
7.2
Protection Register
The 1.8 Volt Intel Wireless Flash memory includes a 128-bit protection register. This protection
register is used to increase system security and for identification purposes. The protection register
value can match the flash component to the system’s CPU or ASIC to prevent device substitution.
The lower 64 bits within the protection register are programmed by Intel with a unique number in
each flash device. The upper 64 OTP bits within the protection register are left for the customer to
program. Once programmed, the customer segment can be locked to prevent further programming.
42
Datasheet
Intel® Wireless Flash Memory (W18)
Note:
The individual bits of the user segment of the protection register are OTP, not the register in total.
The user may program each OTP bit individually, one at a time, if desired. After the protection
register is locked, however, the entire user segment is locked and no more user bits can be
programmed.
The protection register shares some of the same internal flash resources as the parameter partition.
Therefore, RWW is only allowed between the protection register and main partitions. Table 12
describes the operations allowed in the protection register, parameter partition, and main partition
during RWW and RWE.
Table 12. Simultaneous Operations Allowed with the Protection Register
Protection
Register
Parameter
Partition
Array Data
Main
Partitions
Description
Read
See
Description
Write/Erase
While programming or erasing in a main partition, the protection register can be
read from any other partition. Reading the parameter partition data is not
allowed if the protection register is being read from addresses within the
parameter partition.
See
Description
Read
Write/Erase
While programming or erasing in a main partition, read operations are allowed
in the parameter partition. Accessing the protection registers from parameter
partition addresses is not allowed.
Read
Read
Write/Erase
While programming or erasing in a main partition, read operations are allowed
in the parameter partition. Accessing the protection registers in a partition that
is different from the one being programmed or erased, and also different from
the parameter partition, is allowed.
Write
No Access
Allowed
Read
While programming the protection register, reads are only allowed in the other
main partitions. Access to the parameter partition is not allowed. This is
because programming of the protection register can only occur in the
parameter partition, so it will exist in status mode.
No Access
Allowed
Write/Erase
Read
While programming or erasing the parameter partition, reads of the protection
registers are not allowed in any partition. Reads in other main partitions are
supported.
7.2.1
Reading the Protection Register
Writing the Read Identifier command allows the protection register data to be read 16 bits at a time
from addresses shown in Table 7, “Device Identification Codes” on page 25. The protection
register is read from the Read Identifier command and can be read in any partition.Writing the
Read Array command returns the device to read-array mode.
7.2.2
Programing the Protection Register
The Protection Program command should be issued only at the parameter (top or bottom) partition
followed by the data to be programmed at the specified location. It programs the upper 64 bits of
the protection register 16 bits at a time. Table 7, “Device Identification Codes” on page 25 shows
allowable addresses. See also Figure 13, “Protection Register Programming Flowchart” on
page 44. Issuing a Protection Program command outside the register’s address space results in a
status register error (SR[4]=1).
Datasheet
43
Intel® Wireless Flash Memory (W18)
7.2.3
Locking the Protection Register
PR-LK.0 is programmed to 0 by Intel to protect the unique device number. PR-LK.1 can be
programmed by the user to lock the user portion (upper 64 bits) of the protection register (See
Figure 14, “Protection Register Locking). This bit is set using the Protection Program command to
program “FFFDh” into PR-LK.
After PR-LK register bits are programmed (locked), the protection register’s stored values can’t be
changed. Protection Program commands written to a locked section result in a status register error
(SR[4]=1, SR[5]=1).
Figure 13. Protection Register Programming Flowchart
PROTECTION REGISTER PROGRAMMINGPROCEDURE
Bus
Command
Comments
Operation
Protection
Data = C0h
Program
Write
Addr = Protection address
Setup
Start
Write C0h
Addr=Prot addr
Write
Write Protect.
Register
Address / Data
Read
Read Status
Register
Standby
SR[7] = 1?
No
Protection Data = Data to program
Program Addr = Protection address
Read SRD
Toggle CE# or OE# to update SRD
Check SR[7]
1 = WSM Ready
0 = WSM Busy
Protection Program operations addresses must be within the
protection register address space. Addresses outside this
space will return an error.
Yes
Repeat for subsequent programming operations.
Full Status
Check
(if desired)
Full status register check can be done after each program or
after a sequence of program operations.
Program
Complete
FULL STATUS CHECK PROCEDURE
Bus
Command
Operation
Read SRD
Standby
SR[4:3] =
1,1
SR[4,1] =
Program
Successful
44
1,0
1,1
SR[1] SR[3] SR[4]
0
1
1 VPP Error
VPP Range Error
Standby
SR[4,1] =
Comments
Programming Error
Locked-Register
Program Aborted
Standby
0
0
1
Protection register
program error
1
0
1
Register locked;
Operation aborted
SR[3] MUST be cleared before the WSM will allow further
program attempts.
Only the Clear Staus Register command clears SR[4:3,1].
If an error is detected, clear the status register before
attempting a program retry or other error recovery.
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 14. Protection Register Locking
0x88
User-Programmable
0x85
0x84
Intel Factory-Programmed
0x81
PR Lock Register 0
0x80
7.3
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
VPP Protection
The 1.8 Volt Intel® Wireless Flash memory provides in-system program and erase at VPP1. For
factory programming, it also includes a low-cost, backward-compatible 12 V programming
feature.(See “Factory Programming” on page 29.) The EFP feature can also be used to greatly
improve factory program performance as explained in Section 5.3, “Enhanced Factory Program
(EFP)” on page 30.
In addition to the flexible block locking, holding the VPP programming voltage low can provide
absolute hardware write protection of all flash-device blocks. If VPP is below VPPLK, program or
erase operations result in an error displayed in SR[3]. (See Figure 15.)
Figure 15. Examples of VPP Power Supply Configurations
System supply
12 V supply
VCC
VPP
System supply
Prot# (logic signal)
VCC
VPP
≤ 10K Ω
• 12 V fast programming
• Absolute write protection with V PP ≤ VPPLK
System supply
VCC
• Low-voltage programming
• Absolute write protection via logic signal
System supply
VCC
(Note 1)
12 V supply
VPP
• Low voltage and 12 V fast programming
VPP
• Low-voltage programming
NOTE: If the VCC supply can sink adequate current, you can use an appropriately valued resistor.
Datasheet
45
Intel® Wireless Flash Memory (W18)
8.0
Set Configuration Register
The Set Configuration Register command sets the burst order, frequency configuration, burst
length, and other parameters.
A two-bus cycle command sequence initiates this operation. The configuration register data is
placed on the lower 16 bits of the address bus (A[15:0]) during both bus cycles. The Set
Configuration Register command is written along with the configuration data (on the address bus).
This is followed by a second write that confirms the operation and again presents the configuration
register data on the address bus. The configuration register data is latched on the rising edge of
ADV#, CE#, or WE# (whichever occurs first). This command functions independently of the
applied VPP voltage. After executing this command, the device returns to read-array mode. The
configuration register’s contents can be examined by writing the Read Identifier command and
then reading location 05h. (See Table 13 and Table 14.)
46
Datasheet
Intel® Wireless Flash Memory (W18)
Table 13. Configuration Register Definitions
Read
Mode
Res’d
RM
R
LC2
LC1
15
14
13
12
WAIT
Polarity
Data
Output
Config
WAIT
Config
Burst
Seq
Clock
Config
Res’d
Res’d
Burst
Wrap
LC0
WT
DOC
WC
BS
CC
R
R
BW
BL2
BL1
BL0
11
10
9
8
7
6
5
4
3
2
1
0
First Access Latency
Count
Burst Length
Table 14. Configuration Register Descriptions
Bit
Name
15
RM
Read Mode
14
R
13-11
First Access Latency
Count
LC2-0
WT
10
9
WAIT Signal Polarity
DOC
Data Output Configuration
8
7
WC
WAIT Configuration
BS
Burst Sequence
CC
Description
Notes1
0 = Synchronous Burst Reads Enabled
1 = Asynchronous Reads Enabled (Default)
2
Reserved
5
001 = Reserved
010 = Code 2
011 = Code 3
100 = Code 4
101 = Code 5
111 = Reserved (Default)
6
0 = WAIT signal is asserted low
1 = WAIT signal is asserted high (Default)
3
0 = Hold Data for One Clock
1 = Hold Data for Two Clock (Default)
6
0 = WAIT Asserted During Delay
1 = WAIT Asserted One Data Cycle before Delay (Default)
6
1 = Linear Burst Order (Default)
0 = Burst Starts and Data Output on Falling Clock Edge
1 = Burst Starts and Data Output on Rising Clock Edge (Default)
6
Clock
Configuration
5
R
Reserved
5
4
R
Reserved
5
3
BW
Burst Wrap
2-0
BL2-0
Burst Length
0 = Wrap bursts within burst length set by CR[2:0]
1 = Don’t wrap accesses within burst length set by CR[2:0].(Default)
001 = 4-Word Burst
010 = 8-Word Burst
011 = 16-Word Burst
111 = Continuous Burst (Default)
4
NOTES:
1. Undocumented combinations of bits are reserved by Intel for future implementations.
2. Synchronous and page read mode configurations affect reads from main blocks and parameter blocks. Status register and
configuration reads support single read cycles. CR[15]=1 disables configuration set by CR[14:0].
3. Data is not ready when WAIT is asserted.
4. Set the synchronous burst length. In asynchronous page mode, the page size equals four words.
5. Set all reserved configuration register bits to zero.
6. Setting the configuration register for synchronous burst-mode with a latency count of 2 (RCR[13:11] = 010), data hold for 2
clocks (RCR.9 = 1), and WAIT asserted one data cycle before delay (RCR.8 =1) is not supported.
Datasheet
47
Intel® Wireless Flash Memory (W18)
8.1
Read Mode (CR[15])
All partitions support two high-performance read configurations: synchronous burst mode and
asynchronous page mode (default). CR[15] sets the read configuration to one of these modes.
Status register, query, and identifier modes support only asynchronous and single-synchronous read
operations.
8.2
First Access Latency Count (CR[13:11])
The First Access Latency Count (CR[13:11]) configuration tells the device how many clocks must
elapse from ADV# de-assertion (VIH) before the first data word should be driven onto its data pins.
The input clock frequency determines this value. See Table 13, “Configuration Register
Definitions” on page 47 for latency values. Figure 16 shows data output latency from ADV#
assertion for different latencies. Refer to Section 8.2.1, “Latency Count Settings” on page 49 for
Latency Code Settings.
Figure 16. First Access Latency Configuration
CLK [C]
Address [A]
Valid
Address
ADV# [V]
Code 2
D[15:0] [Q]
Valid
Output
Code 3
D[15:0] [Q]
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Code 4
D[15:0] [Q]
Valid
Output
Code 5
D[15:0] [Q]
NOTE: Other First Access Latency Configuration settings are reserved.
)
Figure 17. Word Boundary
Word 0 - 3
0
1
2
Word 4 - 7
3
4
5
6
Word 8 - B
7
8
9
Word C - F
A B C D E
F
16 Word Boundary
4 Word Boundary
The 16-word boundary is the end of the device sense word-line.
48
Datasheet
Intel® Wireless Flash Memory (W18)
8.2.1
Latency Count Settings
Table 15. Latency Count Settings for VCCQ = 1.35 V - 1.8 V (.13 µm lithography)
VCCQ = 1.35 V - 1.8 V
Unit
tAVQV/tCHQV (65ns/14ns)
tAVQV/tCHQV (85ns/20ns)
Latency Count
Settings
2
3, 4, 5
2
3, 4, 5
Frequency
< 39
< 54
< 30
< 40
MHz
Table 16. Latency Count Setting for VCCQ = 1.7 V - 2.24 V (.13 µm lithography)
VCCQ = 1.7 - 2.24 V
Unit
tAVQV/tCHQV (60ns/11ns)
tAVQV/tCHQV (80ns/14ns)
Latency Count
Settings
2
3
4, 5
2
3
4, 5
Frequency
Support
< 40
< 61
< 66
< 30
< 45
< 54
MHz
Table 17. Latency Count Setting for VCCQ = 1.7 V - 2.24 V (.18 µm lithography)
VCCQ = 1.7 - 2.24 V
Unit
tAVQV/tCHQV (70ns/14ns)
tAVQV/tCHQV (85ns/18ns)
Latency Count
Settings
2
3, 4, 5
2
3, 4, 5
Frequency
Support
< 35
<52
< 29
< 40
Datasheet
MHz
49
Intel® Wireless Flash Memory (W18)
Figure 18. Example: Latency Count Setting at 3
tADD-DELAY
CLK (C)
0st
tDATA
2rd
1nd
3th
4th
CE# (E)
ADV# (V)
AMAX-0 (A)
Valid Address
Code 3
DQ15-0 (D/Q)
High Z
Valid
Output
Valid
Output
R103
8.3
WAIT Signal Polarity (CR[10])
If the WT bit is cleared (CR[10]=0), then WAIT is configured to be asserted low. This means that a
0 on the WAIT signal indicates that data is not ready and the data bus contains invalid data.
Conversely, if CR[10] is set, then WAIT is asserted high. In either case, if WAIT is deasserted, then
data is ready and valid. WAIT is asserted during asynchronous page mode reads.
8.4
WAIT Signal Function
The WAIT signal indicates data valid when the device is operating in synchronous mode
(CR[15]=0), and when addressing a partition that is currently in read-array mode. The WAIT signal
is only “deasserted” when data is valid on the bus.
When the device is operating in synchronous non-read-array mode, such as read status, read ID, or
read query, WAIT is set to an “asserted” state as determined by CR[10]. See Figure 26, “WAIT
Signal in Synchronous Non-Read Array Operation Waveform” on page 72.
When the device is operating in asynchronous page mode or asynchronous single word read mode,
WAIT is set to an “asserted” state as determined by CR[10]. See Figure 22, “Page-Mode Read
Operation Waveform” on page 68, and Figure 20, “Asynchronous Read Operation Waveform” on
page 66.
From a system perspective, the WAIT signal is in the asserted state (based on CR[10]) when the
device is operating in synchronous non-read-array mode (such as Read ID, Read Query, or Read
Status), or if the device is operating in asynchronous mode (CR[15]=1). In these cases, the system
software should ignore (mask) the WAIT signal, because it does not convey any useful information
about the validity of what is appearing on the data bus.
50
Datasheet
Intel® Wireless Flash Memory (W18)
Table 18. WAIT Signal Conditions
CONDITION
8.5
WAIT
CE# = VIH
CE# = VIL
Tri-State
Active
OE#
No-Effect
Synchronous Array Read
Active
Synchronous Non-Array Read
Asserted
All Asynchronous Read and all Write
Asserted
Data Hold (CR[9])
The Data Output Configuration bit (CR[9]) determines whether a data word remains valid on the
data bus for one or two clock cycles. The processor’s minimum data set-up time and the flash
memory’s clock-to-data output delay determine whether one or two clocks are needed.
A Data Output Configuration set at 1-clock data hold corresponds to a 1-clock data cycle; a Data
Output Configuration set at 2-clock data hold corresponds to a 2-clock data cycle. The setting of
this configuration bit depends on the system and CPU characteristics. For clarification, see Figure
19, “Data Output Configuration with WAIT Signal Delay” on page 52.
A method for determining this configuration setting is shown below.
To set the device at 1-clock data hold for subsequent reads, the following condition must be
satisfied:
t CHQV (ns) + tDATA (ns) ≤ One CLK Period (ns)
As an example, use a clock frequency of 66 MHz and a clock period of 15 ns. Assume the data
output hold time is one clock. Apply this data to the formula above for the subsequent reads:
11 ns + 4 ns ≤ 15 ns
This equation is satisfied, and data output will be available and valid at every clock period. If tDATA
is long, hold for two cycles.
During page-mode reads, the initial access time can be determined by the formula:
t ADD-DELAY (ns) + tDATA (ns) + tAVQV (ns)
Subsequent reads in page mode are defined by:
t APA (ns) + tDATA (ns)
Datasheet
(minimum time)
51
Intel® Wireless Flash Memory (W18)
Figure 19. Data Output Configuration with WAIT Signal Delay
CLK [C]
WAIT (CR.8 = 1)
Note 1
tCHQV
WAIT (CR.8 = 0)
1 CLK
Data Hold
Note 1
Valid
Output
DQ15-0 [Q]
WAIT (CR.8 = 0)
tCHTL/H
WAIT (CR.8 = 1)
2 CLK
Data Hold
DQ15-0 [Q]
Valid
Output
Valid
Output
Note 1
tCHQV
Note 1
Valid
Output
Valid
Output
NOTE: WAIT shown asserted high (CR[10]=1).
8.6
WAIT Delay (CR[8])
The WAIT configuration bit (CR[8]) controls WAIT signal delay behavior for all synchronous
read-array modes. Its setting depends on the system and CPU characteristics. The WAIT can be
asserted either during, or one data cycle before, a valid output.
In synchronous linear read array (no-wrap mode CR[3]=1) of 4-, 8-, 16-, or continuous-word burst
mode, an output delay may occur when a burst sequence crosses its first device-row boundary (16word boundary). If the burst start address is 4-word boundary aligned, the delay does not occur. If
the start address is misaligned to a 4-word boundary, the delay occurs once per burst-mode read
sequence. The WAIT signal informs the system of this delay.
8.7
Burst Sequence (CR[7])
The burst sequence specifies the synchronous-burst mode data order (see Table 19, “Sequence and
Burst Length” on page 53). When operating in a linear burst mode, either 4-, 8-, or 16-word burst
length with the burst wrap bit (CR[3]) set, or in continuous burst mode, the device may incur an
output delay when the burst sequence crosses the first 16-word boundary. (See Figure 17, “Word
Boundary” on page 48 for word boundary description.) This depends on the starting address. If the
starting address is aligned to a 4-word boundary, there is no delay. If the starting address is the end
of a 4-word boundary, the output delay is one clock cycle less than the First Access Latency Count;
this is the worst-case delay. The delay takes place only once, and only if the burst sequence crosses
a 16-word boundary. The WAIT pin informs the system of this delay. For timing diagrams of WAIT
functionality, see these figures:
• Figure 23, “Single Synchronous Read-Array Operation Waveform” on page 69
• Figure 24, “Synchronous 4-Word Burst Read Operation Waveform” on page 70
• Figure 25, “WAIT Functionality for EOWL (End-of-Word Line) Condition Waveform” on
page 71
52
Datasheet
Intel® Wireless Flash Memory (W18)
Table 19. Sequence and Burst Length
Burst Addressing Sequence (Decimal)
Start
Addr.
(Dec)
4-Word
Burst
8-Word Burst
16-Word Burst
CR[2:0]=0
CR[2:0]=010b
CR[2:0]=011b
Linear
Linear
Linear
01b
CR[2:0]=111b
0
0-1-2-3
0-1-2-3-4-5-6-7
0-1-2...14-15
0-1-2-3-4-5-6-...
1
1-2-3-0
1-2-3-4-5-6-7-0
1-2-3...14-15-0
1-2-3-4-5-6-7-...
2
2-3-0-1
2-3-4-5-6-7-0-1
2-3-4...15-0-1
2-3-4-5-6-7-8-...
3
3-0-1-2
3-4-5-6-7-0-1-2
3-4-5...15-0-1-2
3-4-5-6-7-8-9-...
4
4-5-6-7-0-1-2-3
4-5-6...15-0-1-23
4-5-6-7-8-9-10...
5
5-6-7-0-1-2-3-4
5-6-7...15-0-1...4
5-6-7-8-9-10-11...
6
6-7-0-1-2-3-4-5
6-7-8...15-0-1...5
6-7-8-9-10-11-12...
7
7-0-1-2-3-4-5-6
7-8-9...15-0-1...6
7-8-9-10-11-1213...
...
...
...
...
14
...
Wrap (CR[3]=0)
Linear
Continuous
Burst
14-15-0-1...13
14-15-16-17-18-1920-...
15-16-17-18-19-...
0
0-1-2-3
0-1-2-3-4-5-6-7
0-1-2...14-15
0-1-2-3-4-5-6-...
1
1-2-3-4
1-2-3-4-5-6-7-8
1-2-3...15-16
1-2-3-4-5-6-7-...
2
2-3-4-5
2-3-4-5-6-7-8-9
2-3-4...16-17
2-3-4-5-6-7-8-...
3
3-4-5-6
3-4-5-6-7-8-910
3-4-5...17-18
3-4-5-6-7-8-9-...
4
4-5-6-7-8-9-1011
4-5-6...18-19
4-5-6-7-8-9-10...
5
5-6-7-8-9-1011-12
5-6-7...19-20
5-6-7-8-9-10-11...
6
6-7-8-9-10-1112-13
6-7-8...20-21
6-7-8-9-10-11-12...
7
7-8-9-10-1112-13-14
7-8-9...21-22
7-8-9-10-11-1213...
...
14-15-16-17-1819-20-...
15
15-16...29-30
15-16-17-18-1920-21-...
...
14-15...28-29
...
14
...
Datasheet
15-0-1-2-3...14
...
No-Wrap (CR[3]=1)
15
53
Intel® Wireless Flash Memory (W18)
8.8
Clock Edge (CR[6])
Configuring the valid clock edge enables a flexible memory interface to a wide range of burst
CPUs. Clock configuration sets the device to start a burst cycle, output data, and assert WAIT on
the clock’s rising or falling edge.
8.9
Burst Wrap (CR[3])
The burst wrap bit determines whether 4-, 8-, or 16-word burst accesses wrap within the burstlength boundary or whether they cross word-length boundaries to perform linear accesses. Nowrap mode (CR[3]=1) enables WAIT to hold off the system processor, as it does in the continuous
burst mode, until valid data is available. In no-wrap mode (CR[3]=0), the device operates similarly
to continuous linear burst mode but consumes less power during 4-, 8-, or 16-word bursts.
For example, if CR[3]=0 (wrap mode) and CR[2:0] = 1h (4-word burst), possible linear burst
sequences are 0-1-2-3, 1-2-3-0, 2-3-0-1, 3-0-1-2.
If CR[3]=1 (no-wrap mode) and CR[2:0] = 1h (4-word burst length), then possible linear burst
sequences are 0-1-2-3, 1-2-3-4, 2-3-4-5, and 3-4-5-6. CR[3]=1 not only enables limited nonaligned sequential bursts, but also reduces power by minimizing the number of internal read
operations.
Setting CR[2:0] bits for continuous linear burst mode (7h) also achieves the above 4-word burst
sequences. However, significantly more power may be consumed. The 1-2-3-4 sequence, for
example, consumes power during the initial access, again during the internal pipeline lookup as the
processor reads word 2, and possibly again, depending on system timing, near the end of the
sequence as the device pipelines the next 4-word sequence. CR[3]=1 while in 4-word burst mode
(no-wrap mode) reduces this excess power consumption.
8.10
Burst Length (CR[2:0])
The Burst Length bit (BL[2:0]) selects the number of words the device outputs in synchronous read
access of the flash memory array. The burst lengths are 4-word, 8-word, 16-word, and continuous
word.
Continuous-burst accesses are linear only, and do not wrap within any word length boundaries (see
Table 19, “Sequence and Burst Length” on page 53). When a burst cycle begins, the device outputs
synchronous burst data until it reaches the end of the “burstable” address space.
54
Datasheet
Intel® Wireless Flash Memory (W18)
9.0
Power Consumption
1.8 Volt Intel® Wireless Flash memory devices have a layered approach to power savings that can
significantly reduce overall system power consumption. The APS feature reduces power
consumption when the device is selected but idle. If CE# is deasserted, the memory enters its
standby mode, where current consumption is even lower. Asserting RST# provides current savings
similar to standby mode. The combination of these features can minimize memory power
consumption, and therefore, overall system power consumption.
9.1
Active Power
With CE# at VIL and RST# at VIH, the device is in the active mode. Refer to Section 10.3, “DC
Current Characteristics (.13 µm and .18 µm)” on page 58, for ICC values. When the device is in
“active” state, it consumes the most power from the system. Minimizing device active current
therefore reduces system power consumption, especially in battery-powered applications.
9.2
Automatic Power Savings (APS)
Automatic Power Saving (APS) provides low-power operation during a read’s active state. During
APS mode, ICCAPS is the average current measured over any 5 ms time interval 5 µs after the
following events happen:
• There is no internal sense activity;
• CE# is asserted;
• The address lines are quiescent, and at VSSQ or VCCQ.
OE# may be asserted during APS.
9.3
Standby Power
With CE# at VIH and the device in read mode, the flash memory is in standby mode, which disables
most device circuitry and substantially reduces power consumption. Outputs are placed in a highimpedance state independent of the OE# signal state. If CE# transitions to VIH during erase or
program operations, the device continues the operation and consumes corresponding active power
until the operation is complete. ICCS is the average current measured over any 5 ms time interval 5
µs after a CE# de-assertion.
9.4
Power-Up/Down Characteristics
The device is protected against accidental block erasure or programming during power transitions.
Power supply sequencing is not required if VCC, VCCQ, and VPP are connected together; so it
doesn’t matter whether VPP or VCC powers-up first. If VCCQ and/or VPP are not connected to the
system supply, then VCC should attain VCCMIN before applying VCCQ and VPP. Device inputs
should not be driven before supply voltage = VCCMIN. Power supply transitions should only occur
when RST# is low.
Datasheet
55
Intel® Wireless Flash Memory (W18)
9.4.1
System Reset and RST#
The use of RST# during system reset is important with automated program/erase devices because
the system expects to read from the flash memory when it comes out of reset. If a CPU reset occurs
without a flash memory reset, proper CPU initialization will not occur because the flash memory
may be providing status information instead of array data. To allow proper CPU/flash initialization
at system reset, connect RST# to the system CPU RESET# signal.
System designers must guard against spurious writes when VCC voltages are above VLKO.
Because both WE# and CE# must be low for a command write, driving either signal to VIH inhibits
writes to the device. The CUI architecture provides additional protection because alteration of
memory contents can only occur after successful completion of the two-step command sequences.
The device is also disabled until RST# is brought to VIH, regardless of its control input states. By
holding the device in reset (RST# connected to system PowerGood) during power-up/down,
invalid bus conditions during power-up can be masked, providing yet another level of memory
protection.
9.4.2
VCC, VPP, and RST# Transitions
The CUI latches commands issued by system software and is not altered by VPP or CE# transitions
or WSM actions. Read-array mode is its power-up default state after exit from reset mode or after
VCC transitions above VLKO (Lockout voltage).
After completing program or block erase operations (even after VPP transitions below VPPLK), the
Read Array command must reset the CUI to read-array mode if flash memory array access is
desired.
9.5
Power Supply Decoupling
When the device is accessed, many internal conditions change. Circuits are enabled to charge
pumps and switch voltages. This internal activity produces transient noise. To minimize the effect
of this transient noise, device decoupling capacitors are required. Transient current magnitudes
depend on the device outputs’ capacitive and inductive loading. Two-line control and proper
decoupling capacitor selection suppresses these transient voltage peaks. Each flash device should
have a 0.1 µF ceramic capacitor connected between each power (VCC, VCCQ, VPP), and ground
(VSS, VSSQ) signal. High-frequency, inherently low-inductance capacitors should be as close as
possible to package signals.
56
Datasheet
Intel® Wireless Flash Memory (W18)
10.0
Thermal and DC Characteristics
10.1
Absolute Maximum Ratings
Warning:
Stressing the device beyond the “Absolute Maximum Ratings” may cause permanent damage.
These are stress ratings only. Operation beyond the “Operating Conditions” is not recommended,
and extended exposure beyond the “Operating Conditions” may affect device reliability.
Notice: This datasheet contains information on products in the design phase of development. The information
here is subject to change without notice. Do not finalize a design with this information.
Table 20. Absolute Maximum Ratings
Parameter
Note
Maximum Rating
Temperature under Bias
–40 °C to +85 °C
Storage Temperature
–65 °C to +125 °C
Voltage on Any Pin (except VCC, VCCQ, VPP)
–0.5 V to +2.45 V
VPP Voltage
1,2,3
–0.2 V to +14 V
VCC and VCCQ Voltage
1
–0.2 V to +2.45 V
Output Short Circuit Current
4
100 mA
NOTES:
1. All specified voltages are relative to VSS. Minimum DC voltage is –0.5 V on input/output pins and
–0.2 V on VCC and VPP pins. During transitions, this level may undershoot to –2.0 V for periods < 20
ns which, during transitions, may overshoot to VCC +2.0 V for periods < 20 ns.
2. Maximum DC voltage on VPP may overshoot to +14.0 V for periods < 20 ns.
3. VPP program voltage is normally VPP1. VPP can be 12 V ± 0.6 V for 1000 cycles on the main blocks
and 2500 cycles on the parameter blocks during program/erase.
4. Output shorted for no more than one second. No more than one output shorted at a time.
10.2
Operating Conditions
Table 21. Extended Temperature Operation (Sheet 1 of 2)
Symbol
TA
Operating Temperature
VCC
VCC Supply Voltage
Note
3
Min
Nom
Max
Unit
–40
25
85
°C
1.7
1.8
1.95
I/O Supply Voltage
3
1.7
1.8
2.24
I/O Supply Voltage (Extended)
4
1.35
1.5
1.8
VPP1
VPP Voltage Supply (Logic Level)
2
0.90
1.80
1.95
VPP2
Factory Programming VPP
2
11.4
12.0
12.6
tPPH
Maximum VPP Hours
VCCQ
Datasheet
Parameter1
VPP = 12 V
2
80
V
Hours
57
Intel® Wireless Flash Memory (W18)
Table 21. Extended Temperature Operation (Sheet 2 of 2)
Parameter1
Symbol
Block
Erase
Cycles
Note
Min
Nom
100,000
Max
Main and Parameter
Blocks
VPP ≤ VCC
2
Main Blocks
VPP = 12 V
2
1000
Parameter Blocks
VPP = 12 V
2
2500
Unit
Cycles
NOTES:
1. See Section 10.3 and Section 10.4, “DC Voltage Characteristics” on page 60 for specific voltage-range
specifications.
2. VPP is normally VPP1. VPP can be connected to 11.4 V–12.6 V for 1000 cycles on main blocks for
extended temperatures and 2500 cycles on parameter blocks at extended temperature.
3. Contact your Intel field representative for VCC/VCCQ operations down to 1.65 V.
4. See the tables in Section 10.0, “Thermal and DC Characteristics” on page 57 and in Section 11.0, “AC
Characteristics” on page 62 for operating characteristics within the Extended-VCCQ voltage range.
10.3
DC Current Characteristics (.13 µm and .18 µm)
Table 22. DC Current Characteristics (Sheet 1 of 3)
VCCQ=1.35 V –
1.8 V
Parameter (1)
Sym
Note
32/64/128 Mbit
Typ
ILI
Input Load
ILO
Output
Leakage
.18 µm
ICCS
.13 µm
ICCS
9
DQ[15:0]
TBD
VCC Standby
APS
58
32/64 Mbit
Typ
Max
128 Mbit
Typ
Unit
Test Condition
Max
TBD
±1
±1
µA
VCC = VCCMax
VCCQ = VCCQMax
VIN = VCCQ or GND
TBD
±1
±1
µA
VCC = VCCMax
VCCQ = VCCQMax
VIN = VCCQ or GND
µA
VCC = VCCMax
VCCQ = VCCQMax
CE# = VCC
RST# =VSSQ
µA
VCC = VCCMax
VCCQ = VCCQMax
CE# = VSSQ
RST# =VCCQ
All other inputs =VCCQ or
VSSQ
TBD
5
18
5
25
10
.18 µm
ICCAPS
.13 µm
ICCAPS
Max
VCCQ= 1.8 V
TBD
TBD
8
50
8
70
TBD
TBD
5
18
5
25
TBD
TBD
8
50
8
70
11
Datasheet
Intel® Wireless Flash Memory (W18)
Table 22. DC Current Characteristics (Sheet 2 of 3)
VCCQ=1.35 V –
1.8 V
Parameter (1)
Sym
Asynchronous
Page Mode
f=13 MHz
Synchronous
CLK = 40 MHz
ICCR
ICCW
ICCE
2
Average
VCC
Read
Synchronous
CLK = 66 MHz
VCC Program
VCC Block Erase
32/64/128 Mbit
32/64 Mbit
128 Mbit
Unit
Test Condition
Typ
Max
Typ
Max
Typ
Max
TBD
TBD
3
6
4
7
mA
4 Word Read
TBD
TBD
6
13
6
13
mA
Burst length
=4
TBD
TBD
8
14
8
14
mA
Burst length
=8
TBD
TBD
10
18
11
19
mA
Burst length
=16
TBD
TBD
11
20
11
20
mA
Burst length
= Continuous
TBD
TBD
7
16
7
16
mA
Burst length
=4
TBD
TBD
10
18
10
18
mA
Burst length
=8
TBD
TBD
12
22
12
22
mA
Burst length
= 16
TBD
TBD
13
25
13
25
mA
Burst length
= Continuous
TBD
TBD
8
17
N.A.
N.A.
mA
Burst length
=4
TBD
TBD
11
20
N.A.
N.A.
mA
Burst length
=8
TBD
TBD
14
25
N.A.
N.A.
mA
Burst length
= 16
TBD
TBD
16
30
N.A.
N.A.
mA
Burst length
= Continuous
TBD
TBD
18
40
18
40
mA
VPP = VPP1, Program in
Progress
TBD
TBD
8
15
8
15
mA
VPP = VPP2, Program in
Progress
TBD
TBD
18
40
18
40
mA
VPP = VPP1, Block Erase in
Progress
TBD
TBD
8
15
8
15
mA
VPP = VPP2, Block Erase in
Progress
2
Average
VCC
Read
Synchronous
CLK = 54 MHz
ICCR
Note
VCCQ= 1.8 V
2
2, 3
3,4,5
3,4,5
VCC =
VCCMax
CE# = VIL
OE# = VIH
Inputs = VIH
or VIL
VCC =
VCCMax
CE# = VIL
OE# = VIH
Inputs = VIH
or VIL
ICCWS
VCC Program Suspend
6
TBD
TBD
5
18
5
25
µA
CE# = VCC, Program Suspended
ICCES
VCC Erase Suspend
6
TBD
TBD
5
18
5
25
µA
CE# = VCC, Erase Suspended
Datasheet
59
Intel® Wireless Flash Memory (W18)
Table 22. DC Current Characteristics (Sheet 3 of 3)
VCCQ=1.35 V –
1.8 V
Sym
IPPS
Parameter (1)
Note
IPPES)
VPP Standby
VPP Program Suspend
VPP Erase Suspend
IPPR
VPP Read
(IPPWS
,
IPPW
IPPE
VPP Program
3
32/64/128 Mbit
VCCQ= 1.8 V
32/64 Mbit
128 Mbit
Test Condition
Typ
Max
Typ
Max
Typ
Max
TBD
TBD
0.2
5
0.2
5
µA
VPP <VCC
TBD
TBD
2
15
2
15
µA
VPP ≤ VCC
TBD
TBD
0.05
0.10
0.05
0.10
TBD
TBD
8
22
16
37
TBD
TBD
0.05
0.10
0.05
0.10
TBD
TBD
8
22
8
22
4
VPP Erase
Unit
VPP = VPP1, Program in
Progress
mA
4
mA
VPP = VPP2, Program in
Progress
VPP = VPP1, Erase in
Progress
VPP = VPP2, Erase in
Progress
NOTES:
1. All currents are RMS unless noted. Typical values at typical VCC, TA = +25°C.
2. Automatic Power Savings (APS) reduces ICCR to approximately standby levels in static operation. See ICCRQ specification
for details.
3. Sampled, not 100% tested.
4. VCC read + program current is the sum of VCC read and VCC program currents.
5. VCC read + erase current is the sum of VCC read and VCC erase currents.
6. ICCES is specified with device deselected. If device is read while in erase suspend, current is ICCES plus ICCR.
7. VPP <= VPPLK inhibits erase and program operations. Don’t use VPPL and VPPH outside their valid ranges.
8. VIL can undershoot to –0.4V and VIH can overshoot to VCCQ+0.4V for durations of 20 ns or less.
9. If VIN>VCC the input load current increases to 10 µA max.
10.ICCS is the average current measured over any 5ms time interval 5µs after a CE# de-assertion.
11.Refer to section Section 9.2, “Automatic Power Savings (APS)” on page 55 for ICCAPS measurement details.
12.TBD values are to be determined pending silicon characterization.
10.4
DC Voltage Characteristics
Table 23. DC Voltage Characteristics (Sheet 1 of 2)
VCCQ=1.35 V – 1.8 V
Sym
VIL
Parameter (1)
Input Low
VIH
Input High
VOL
Output Low
60
Note
8
32/64/128 Mbit
Min
Max
0
VCCQ
– 0.2
VCCQ= 1.8 V
32/64 Mbit
Min
Max
0.2
0
VCCQ
VCCQ
– 0.4
0.1
128 Mbit
Unit
Min
Max
0.4
0
0.4
V
VCCQ
VCCQ
– 0.4
VCCQ
V
0.1
V
0.1
Test Condition
VCC = VCCMin
VCCQ = VCCQMin
IOL = 100 µA
Datasheet
Intel® Wireless Flash Memory (W18)
Table 23. DC Voltage Characteristics (Sheet 2 of 2)
VCCQ=1.35 V – 1.8 V
Sym
Parameter (1)
Note
32/64/128 Mbit
Min
Max
VCCQ= 1.8 V
32/64 Mbit
Min
Max
128 Mbit
Min
Unit
Test Condition
V
VCC = VCCMin
VCCQ = VCCQMin
IOH = –100 µA
Max
VOH
Output High
VPPLK
VPP Lock-Out
VLKO
VCC Lock
1.0
1.0
1.0
V
VILKOQ
VCCQ Lock
TBD
0.9
0.9
V
VCCQ
– 0.1
7
VCCQ
– 0.1
0.4
VCCQ
– 0.1
0.4
0.4
V
NOTE: For all numbered note references in this table, refer to the notes in Table 22, “DC Current Characteristics” on page 58.
Datasheet
61
Intel® Wireless Flash Memory (W18)
11.0
AC Characteristics
11.1
Read Operations – .13 µm Lithography
Table 24. Read Operations— .13 µm Lithography (Sheet 1 of 2)
VCCQ=
1.35 V – 1.8 V
#
Parameter 1,2
Sym
Notes
-65
Min
VCCQ=
1.7 V – 2.24 V
-85
Max
Min
-60
Max
Min
Unit
-80
Max
Min
Max
Asynchronous Specifications
R1
tAVAV
Read Cycle Time
7,8
65
85
60
80
ns
R2
tAVQV
Address to Output Valid
7,8
65
85
60
80
ns
R3
tELQV
CE# Low to Output Valid
7,8
65
85
60
80
ns
R4
tGLQV
OE# Low to Output Valid
4
25
30
20
25
ns
R5
tPHQV
RST# High to Output Valid
150
150
150
150
ns
R6
tELQX
CE# Low to Output Low-Z
5
0
0
0
0
ns
R7
tGLQX
OE# Low to Output Low-Z
4,5
0
0
0
0
ns
R8
tEHQZ
CE# High to Output High-Z
5
17
20
14
17
ns
R9
tGHQZ
OE# High to Output High-Z
4,5
14
14
14
14
ns
R10
tOH
CE# (OE#) High to Output Low-Z
4,5
0
0
0
0
ns
Latching Specifications
R101
tAVVH
Address Setup to ADV# High
7
7
7
7
ns
R102
tELVH
CE# Low to ADV# High
10
10
10
10
ns
R103
tVLQV
ADV# Low to Output Valid
R104
tVLVH
ADV# Pulse Width Low
7
7
7
7
ns
R105
tVHVL
ADV# Pulse Width High
7
7
7
7
ns
R106
tVHAX
Address Hold from ADV# High
7
7
7
7
ns
R108
tAPA
Page Address Access Time
7,8
3
65
85
60
80
ns
25
30
20
25
ns
54
40
66
54
MHz
Clock Specifications
R200
fCLK
CLK Frequency
R201
tCLK
CLK Period
18.5
R202
tCH/L
CLK High or Low Time
4.5
R203
tCHCL
CLK Fall or Rise Time
62
25
15
9.5
3
18.5
3.5
3
ns
4.5
3
ns
3
ns
Datasheet
Intel® Wireless Flash Memory (W18)
Table 24. Read Operations— .13 µm Lithography (Sheet 2 of 2)
VCCQ=
1.35 V – 1.8 V
#
Sym
Parameter 1,2
Notes
-65
Min
VCCQ=
1.7 V – 2.24 V
-85
Max
Min
-60
Max
Min
Unit
-80
Max
Min
Max
Synchronous Specifications
R301
tAVCH
Address Valid Setup to CLK
7
7
7
7
ns
R302
tVLCH
ADV# Low Setup to CLK
7
7
7
7
ns
R303
tELCH
CE# Low Setup to CLK
R304
tCHQV
CLK to Output Valid
R305
tCHQX
Output Hold from CLK
R306
tCHAX
Address Hold from CLK
R307
tCHTV
CLK to WAIT Valid
8
14
20
11
14
ns
R308
tELTV
CE# Low to WAIT Valid
6
14
20
11
14
ns
R309
tEHTZ
CE# High to WAIT High-Z
5,6
14
20
11
14
ns
R310
tEHEL
CE# Pulse Width High
Datasheet
7
8
3
6
7
14
7
20
7
11
ns
14
ns
3
3
3
3
ns
7
7
7
7
ns
14
14
14
14
ns
63
Intel® Wireless Flash Memory (W18)
Read Operations – .18 µm Lithography
11.2
Table 25. Read Operations — .18 µm Lithography (Sheet 1 of 2)
32/64 Mbit
#
Parameter (1,2)
Sym
Notes
–70
Min
128 Mbit
–85
Max
Min
-85
Max
Min
Unit
Max
Asynchronous Specifications
R1
tAVAV
Read Cycle Time
70
R2
tAVQV
Address to Output Delay
70
85
85
ns
R3
tELQV
CE# Low to Output Delay
70
85
85
ns
R4
tGLQV
OE# Low to Output Delay
30
30
30
ns
R5
tPHQV
RST# High to Output Delay
150
150
150
ns
R6
tELQX
CE# Low to Output in Low-Z
5
0
0
0
ns
R7
tGLQX
OE# Low to Output in Low-Z
4,5
0
0
0
ns
R8
tEHQZ
CE# High to Output in High-Z
5
20
20
20
ns
R9
tGHQZ
OE# High to Output in High-Z
4,5
14
14
14
ns
R10
tOH
CE# (OE#) High to Output in Low-Z
4,5
4
85
85
ns
0
0
0
ns
Latching Specifications
R101
tAVVH
Address Setup to ADV# High
10
10
10
ns
R102
tELVH
CE# Low to ADV# High
10
10
10
ns
R103
tVLQV
ADV# Low to Output Delay
R104
tVLVH
ADV# Pulse Width Low
10
10
10
ns
R105
tVHVL
ADV# Pulse Width High
10
10
10
ns
R106
tVHAX
Address Hold from ADV# High
9
9
9
ns
R108
tAPA
Page Address Access Time
70
3
85
85
ns
20
25
25
ns
52
40
40
MHz
Clock Specifications
R200
fCLK
CLK Frequency
R201
tCLK
CLK Period
19
R202
tCH/L
CLK High or Low Time
5
R203
tCHCL
CLK Fall or Rise Time
64
25
25
5
3
ns
5
3
ns
3
ns
Datasheet
Intel® Wireless Flash Memory (W18)
Table 25. Read Operations — .18 µm Lithography (Sheet 2 of 2)
32/64 Mbit
#
Sym
Parameter (1,2)
Notes
–70
Min
128 Mbit
–85
Max
Min
-85
Max
Min
Unit
Max
Synchronous Specifications
R301 tAVCH
Address Valid Setup to CLK
9
9
9
ns
R302 tVLCH
ADV# Low Setup to CLK
10
10
10
ns
R303 tELCH
CE# Low Setup to CLK
9
9
9
ns
R304 tCHQV
CLK to Output Valid
R305 tCHQX
Output Hold from CLK
R306 tCHAX
Address Hold from CLK
R307 tCHTV
CLK to WAIT Valid
R308 tELTV
CE# Low to WAIT Valid
R309 tEHTZ
CE# High to WAIT High-Z
R310 tEHEL
CE# Pulse Width High
14
3.5
3
18
3.5
10
18
3.5
10
ns
ns
10
ns
14
18
18
ns
6
14
18
18
ns
5,6
20
25
25
ns
6
15
20
20
ns
NOTES:
1. See Figure 34, “AC Input/Output Reference Waveform” on page 81 for timing measurements and maximum allowable input
slew rate.
2. AC specifications assume the data bus voltage is less than or equal to VCCQ when a read operation is initiated.
3. Address hold in synchronous-burst mode is defined as tCHAX or tVHAX, whichever timing specification is satisfied first.
4. OE# may be delayed by up to tELQV– tGLQV after the falling edge of CE# without impact to tELQV.
5. Sampled, not 100% tested.
6. Applies only to subsequent synchronous reads.
7. During the initial access of a synchronous burst read, data from the first word may begin to be driven onto the data bus as
early as the first clock edge after tAVQV.
8. All specs above apply to all densities.
x
Datasheet
65
Intel® Wireless Flash Memory (W18)
Figure 20. Asynchronous Read Operation Waveform
R1
Address [A]
VIH
Valid
Address
VIL
R2
CE# [E]
VIH
VIL
R3
OE# [G]
R8
VIH
R4
VIL
R7
WE# [W]
R9
VIH
VIL
WAIT [T]
VOH
High Z
High Z
Note 1
VOL
Data [D/Q]
VOH
High Z
Valid
Output
VOL
R5
RST# [P]
R10
VIH
VIL
NOTES:.
1. WAIT shown asserted (CR.10=0)
2. ADV# assumed to be driven to VIL in this waveform
66
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 21. Latched Asynchronous Read Operation Waveform
R1
A[MAX:2] [A]
VIH
VIL
A[1:0] [A]
Valid
Address
Valid
Address
VIH
Valid
Address
VIL
Valid
Address
R2
R101
R105
ADV# [V]
R106
VIH
VIL
R104
R103
CE# [E]
VIH
R3
VIL
R102
R4
R8
R6
OE# [G]
VIH
VIL
R7
WE# [W]
R9
VIH
VIL
Data [Q]
VOH
High Z
Valid
Output
VOL
R5
RST# [P]
R10
VIH
VIL
Datasheet
67
Intel® Wireless Flash Memory (W18)
Figure 22. Page-Mode Read Operation Waveform
R1
A[MAX:2] [A]
VIH
Valid
Address
VIL
R2
A[1:0] [A]
VIH
Valid
Address
VIL
Valid
Address
Valid
Address
Valid
Address
R101
R105
ADV# [V]
R106
VIH
VIL
R104
R103
CE# [E]
VIH
R3
VIL
R102
R4
R8
R6
OE# [G]
VIH
VIL
R7
WE# [W]
R9
VIH
VIL
WAIT [T]
VOH
High Z
Note 1
High Z
R108
VOL
Data [D/Q]
VOH
High Z
Valid
Output
VOL
R5
RST# [P]
Valid
Output
Valid
Output
Valid
Output
R10
VIH
VIL
NOTE: WAIT shown asserted (CR.10 = 0).
68
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 23. Single Synchronous Read-Array Operation Waveform
CLK [C]
VIH
Note 1
VIL
R301
Address [A]
VIH
R306
Valid
Address
VIL
R2
R101
R105
ADV# [V]
R106
VIH
R302
VIL
R104
R103
CE# [E]
VIH
R3
VIL
R102
OE# [G]
R4
R8
VIH
VIL
R303
WE# [W]
R7
R9
VIH
R309
VIL
R308
WAIT [T]
VOH
High Z
R10
High Z
Note 2
VOL
R304
Data [Q]
VOH
High Z
R305
Valid
Output
VOL
R5
RST# [P]
VIH
VIL
NOTES:
1. Section 8.2, “First Access Latency Count (CR[13:11])” on page 48 describes how to insert clock cycles during
the initial access.
2. WAIT (shown asserted; CR.10=0) can be configured to assert either during, or one data cycle before, valid
data.
3. This waveform illustrates the case in which an x-word burst is initiated to the main array and it is terminated
by a CE# de-assertion after the first word in the burst. If this access had been done to Status, ID, or Query
reads, the asserted (low) WAIT signal would have remained asserted (low) as long as CE# is asserted (low).
Datasheet
69
Intel® Wireless Flash Memory (W18)
Figure 24. Synchronous 4-Word Burst Read Operation Waveform
CLK [C]
VIH
VIL
0
R301
Address [A]
Note 1
1
VIH
R306
Valid
Address
VIL
R2
R101
R105
ADV# [V]
R106
VIH
R302
VIL
R104
R103
CE# [E]
VIH
R310
R3
VIL
R102
OE# [G]
R4
R8
VIH
VIL
R303
WE# [W]
R7
R9
VIH
R309
R308
VIL
R10
R307
WAIT [T]
VOH
High Z
High Z
Note 2
VOL
R304
Data [Q]
VOH
High Z
R305
Valid
Output
VOL
Valid
Output
Valid
Output
Valid
Output
High Z
R5
RST# [P]
VIH
VIL
NOTES:
1. Section 8.2, “First Access Latency Count (CR[13:11])” on page 48 describes how to insert clock cycles during
the initial access.
2. WAIT (shown asserted; CR.10 = 0) can be configured to assert either during, or one data cycle before, valid
data.
70
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 25. WAIT Functionality for EOWL (End-of-Word Line) Condition Waveform
VIH
CLK [C]
VIL
0
R301
VIH
Address [A]
Note 1
1
R306
Valid
Address
VIL
R2
R101
R105
ADV# [V]
R106
VIH
R302
VIL
R104
R103
CE# [E]
VIH
R3
VIL
R102
OE# [G]
R4
VIH
VIL
R303
WE# [W]
R7
VIH
R308
VIL
R307
WAIT [T]
VOH
High Z
High Z
Note 2
VOL
R304
Data [D/Q]
VOH
High Z
R305
Valid
Output
VOL
Valid
Output
Valid
Output
Valid
Output
R5
RST# [P]
VIH
VIL
NOTES:
1. Section 8.2, “First Access Latency Count (CR[13:11])” on page 48 describes how to insert clock cycles during
the initial access.
2. WAIT (shown asserted; CR.10=0) can be configured to assert either during, or one data cycle before, valid
data. (assumed wait delay of two clocks for example)
Datasheet
71
Intel® Wireless Flash Memory (W18)
Figure 26. WAIT Signal in Synchronous Non-Read Array Operation Waveform
CLK [C]
VIH
Note 1
VIL
R301
Address [A]
VIH
R306
Valid
Address
VIL
R2
R101
R105
ADV# [V]
R106
VIH
R302
VIL
R104
R103
CE# [E]
VIH
R3
VIL
R102
OE# [G]
R4
R8
VIH
VIL
R303
WE# [W]
R7
R9
VIH
R309
VIL
R308
WAIT [T]
VOH
High Z
R10
High Z
Note 2
VOL
R304
Data [Q]
VOH
High Z
R305
Valid
Output
VOL
R5
RST# [P]
VIH
VIL
NOTES:
1. Section 8.2, “First Access Latency Count (CR[13:11])” on page 48 describes how to insert clock cycles during
the initial access.
2. WAIT shown asserted (CR.10=0).
72
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 27. Burst Suspend
R304
R305
R305
R305
CLK
R1
R2
Address [A]
R101
R105
R106
ADV#
R3
R8
CE# [E]
R4
R9
R4
R9
OE# [G]
R13
R12
WAIT [T]
WE# [W]
R7
R6
DATA [D/Q]
Q0
R304
Q1
Q1
R304
Q2
NOTE:
1. During Burst Suspend Clock signal can be held high or low
Datasheet
73
Intel® Wireless Flash Memory (W18)
11.3
AC Write Characteristics
Table 26. AC Write Characteristics –
.13 µm Lithography
VCCQ=
1.35 V – 1.8 V
#
Sym
Parameter 1,2
Notes
-65
Min
W1
tPHWL (tPHEL)
RST# High Recovery to WE#
(CE#) Low
W2
tELWL (tWLEL)
CE# (WE#) Setup to WE# (CE#)
Low
W3
tWLWH (tELEH)
WE# (CE#) Write Pulse Width
Low
W4
tDVWH (tDVEH)
W5
tAVWH (tAVEH)
W6
tWHEH
(tEHWH)
-85
Min
Max
-60
Min
Max
-80
Min
Unit
Max
150
150
150
150
ns
0
0
0
0
ns
50
60
40
60
ns
Data Setup to WE# (CE#) High
50
60
40
60
ns
Address Setup to WE# (CE#)
High
50
60
40
60
ns
CE# (WE#) Hold from WE# (CE#)
High
0
0
0
0
ns
W7
tWHDX (tEHDX) Data Hold from WE# (CE#) High
0
0
0
0
ns
W8
tWHAX (tEHAX)
Address Hold from WE# (CE#)
High
0
0
0
0
ns
W9
tWHWL (tEHEL)
WE# (CE#) Pulse Width High
5,6,7
20
25
20
25
ns
W10
tVPWH (tVPEH)
3
200
200
200
200
ns
W11
tQVVL
VPP Hold from Valid SRD
3,8
0
0
0
0
ns
W12
tQVBL
WP# Hold from Valid SRD
3,8
0
0
0
0
ns
3
200
200
200
200
ns
0
0
0
0
ns
tAVQV
+ 55
tAVQV
+20
tAVQV
+50
ns
VPP Setup to WE# (CE#) High
W13 tBHWH (tBHEH) WP# Setup to WE# (CE#) High
W14
tWHGL (tEHGL)
3
Max
VCCQ=
1.7 V – 2.24 V
4
Write Recovery before Read
W16
tWHQV
WE# High to Valid Data
3,6,10
tAVQV
+ 25
W18
tWHAV
WE# High to Address Valid
3,9,10
0
0
0
0
ns
W19
tWHCV
WE# High to CLK Valid
3,10
16
20
12
20
ns
W20
tWHVH
WE# High to ADV# High
3,10
16
20
12
20
ns
NOTES:
1. Write timing characteristics during erase suspend are the same as during write-only operations.
2. A write operation can be terminated with either CE# or WE#.
3. Sampled, not 100% tested.
4. Write pulse width low (tWLWH or tELEH) is defined from CE# or WE# low (whichever occurs last) to CE# or WE# high
(whichever occurs first). Hence, tWLWH = tELEH = tWLEH = tELWH.
5. Write pulse width high (tWHWL or tEHEL) is defined from CE# or WE# high (whichever is first) to CE# or WE# low (whichever is
last). Hence, tWHWL = tEHEL = tWHEL = tEHWL.
6. System designers should take this into account and may insert a software No-Op instruction to delay the first read after
issuing a command.
7. For commands other than resume commands.
8. VPP should be held at VPP1 or VPP2 until block erase or program success is determined.
9. Applicable during asynchronous reads following a write.
10.tWHCH/L OR tWHVH must be met when transitioning from a write cycle to a synchronous burst read. tWHCH/L and tWHVH both refer to
the address latching event (either the rising/falling clock edge or the rising ADV# edge, whichever occurs first).
74
Datasheet
Intel® Wireless Flash Memory (W18)
l
Table 27. AC Write Characteristics –
.18 µm Lithography
32-Mbit
64-Mbit
128-Mbit
#
Sym
Parameter 1,2
Notes
Unit
-70
Min
W1
tPHWL (tPHEL)
RST# High Recovery to WE# (CE#) Low
W2
tELWL (tWLEL)
CE# (WE#) Setup to WE# (CE#) Low
W3
tWLWH (tELEH)
WE# (CE#) Write Pulse Width Low
W4
tDVWH (tDVEH)
W5
W6
W7
Min
Max
150
150
ns
0
0
ns
45
60
ns
Data Setup to WE# (CE#) High
45
60
ns
tAVWH (tAVEH)
Address Setup to WE# (CE#) High
45
60
ns
tWHEH (tEHWH)
CE# (WE#) Hold from WE# (CE#) High
0
0
ns
tWHDX (tEHDX)
Data Hold from WE# (CE#) High
0
0
ns
W8
tWHAX (tEHAX)
Address Hold from WE# (CE#) High
0
0
ns
W9
tWHWL (tEHEL)
WE# (CE#) Pulse Width High
W10
tVPWH (tVPEH)
VPP Setup to WE# (CE#) High
W11
tQVVL
W12
tQVBL
3
Max
-85
4
5,6,7
25
25
ns
3
200
200
ns
VPP Hold from Valid SRD
3,8
0
0
ns
WP# Hold from Valid SRD
3,8
0
0
ns
3
200
200
ns
0
0
ns
W13
tBHWH (tBHEH)
WP# Setup to WE# (CE#) High
W14
tWHGL (tEHGL)
Write Recovery before Read
W16
tWHQV
WE# High to Valid Data
3,6,10
tAVQV
+ 40
tAVQV
+ 50
ns
W18
tWHAV
WE# High to Address Valid
3,9,10
0
0
ns
W19
tWHCV
WE# High to CLK Valid
3,10
20
20
ns
W20
tWHVH
WE# High to ADV# High
3,10
20
20
ns
NOTES:
1. Write timing characteristics during erase suspend are the same as during write-only operations.
2. A write operation can be terminated with either CE# or WE#.
3. Sampled, not 100% tested.
4. Write pulse width low (tWLWH or tELEH) is defined from CE# or WE# low (whichever occurs last) to CE# or WE#
high (whichever occurs first). Hence, tWLWH = tELEH = tWLEH = tELWH.
5. Write pulse width high (tWHWL or tEHEL) is defined from CE# or WE# high (whichever is first) to CE# or WE# low
(whichever is last). Hence, tWHWL = tEHEL = tWHEL = tEHWL.
6. System designers should take this into account and may insert a software No-Op instruction to delay the first
read after issuing a command.
7. For commands other than resume commands.
8. VPP should be held at VPP1 or VPP2 until block erase or program success is determined.
9. Applicable during asynchronous reads following a write.
10.tWHCH/L OR tWHVH must be met when transitioning from a write cycle to a synchronous burst read. tWHCH/L and tWHVH
both refer to the address latching event (either the rising/falling clock edge or the rising ADV# edge, whichever
occurs first).
Datasheet
75
Intel® Wireless Flash Memory (W18)
Figure 28. Write Operations Waveform
CLK [C]
VIH
VIL
W19
Note 1
Address [A]
VIH
VIL
Note 2
Note 3
Valid
Address
Note 4
Valid
Address
Note 5
Valid
Address
W5
W18
R101
R105
ADV# [V]
R106
W8
VIH
VIL
R104
CE# (WE#) [E(W)]
W20
VIH
Note 6
VIL
W2
OE# [G]
W6
VIH
VIL
W3
W14
W9
WE# (CE#) [W(E)]
VIH
Note 6
VIL
W1
Data [Q]
W7
W16
VIH
Data In
Valid
SRD
Data In
VIL
W4
RST# [P]
VIH
VIL
WP# [B]
W13
W12
W10
W11
VIH
VIL
VPPH
VPP [V]
VPPLK
VIL
NOTES:
1. VCC power-up and standby.
2. Write Program or Erase Setup command.
3. Write valid address and data (for program) or Erase Confirm command.
4. Automated program/erase delay.
5. Read status register data (SRD) to determine program/erase operation completion.
6. OE# and CE# must be asserted and WE# must be deasserted for read operations.
7. CLK is ignored. (but may be kept active/toggling)
76
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 29. Asynchronous Read to Write Operation Waveform
R1
R2
W5
W8
Address [A]
R3
R8
CE# [E}
R4
R9
OE# [G]
W3
W2
W6
WE# [W]
R7
R6
W7
R10
Data [D/Q]
W4
Q
D
R5
RST# [P]
Figure 30. Asynchronous Write to Read Operation
W5
W8
R1
Address [A]
W2
W6
R10
CE# [E}
W3
W18
WE# [W]
W14
OE# [G]
W7
W4
Data [D/Q]
D
R4
R2
R3
R9
R8
Q
W1
RST # [P]
Datasheet
77
Intel® Wireless Flash Memory (W18)
Figure 31. Synchronous Read to Write Operation
Latency Count
R301
R302
R306
CLK [C]
R2
W5
R101
W18
Address [A]
R105
R106
R104
R102
W20
ADV# [V]
R303
R3
R11
W6
CE# [E]
R4
R8
OE# [G]
W15
W19
W9
W8
W3
W2
WE#
R12
R307
WAIT [T]
R304
R13
R7
Data [D/Q]
R305
W7
Q
D
D
Figure 32. Synchronous Write To Read Operation
Lat ency Count
R302
R301
R2
CLK
W5
W8
R306
Address [A]
W20
R106
R104
ADV#
W6
W2
R303
R11
CE# [E}
W18
W19
W3
WE# [W]
R4
OE# [G ]
R12
R307
WAIT [T]
W7
W4
Data [D/Q ]
R304
R3
D
Q
R304
R305
Q
W1
RST# [P]
78
Datasheet
Intel® Wireless Flash Memory (W18)
11.4
Erase and Program Times
Table 28. Erase and Program Times
Operation
Symbol
Description1
Parameter
VPP1
VPP2
Notes
Unit
Typ
Max
Typ
Max
Erasing and Suspending
Erase Time
Suspend
Latency
W500
tERS/PB
4-Kword Parameter Block
2,3
0.3
2.5
0.25
2.5
s
W501
tERS/MB
32-Kword Main Block
2,3
0.7
4
0.4
4
s
W600
tSUSP/P
Program Suspend
2
5
10
5
10
µs
W601
tSUSP/E
Erase Suspend
2
5
20
5
20
µs
W200
tPROG/W
Single Word
2
12
150
8
130
µs
W201
tPROG/PB
4-Kword Parameter Block
2,3
0.05
.23
0.03
0.07
s
W202
tPROG/MB
32-Kword Main Block
2,3
0.4
1.8
0.24
0.6
s
4
N/A
N/A
3.1
16
µs
Programming
Program
Time
5
Enhanced Factory Programming
Program
Operation
Latency
W400
tEFP/W
Single Word
W401
tEFP/PB
4-Kword Parameter Block
2,3
N/A
2,3
N/A
15
W402
tEFP/MB
32-Kword Main Block
W403
tEFP/SETUP
EFP Setup
W404
tEFP/TRAN
Program to Verify Transition
N/A
N/A
W405
tEFP/VERIFY
Verify
N/A
N/A
ms
120
N/A
ms
5
µs
2.7
5.6
µs
1.7
130
µs
NOTES:
1. Unless noted otherwise, all parameters are measured at TA = +25 °C and nominal voltages, and they are sampled, not 100%
tested.
2. Excludes external system-level overhead.
3. Exact results may vary based on system overhead.
4. W400-Typ is the calculated delay for a single programming pulse. W400-Max includes the delay when programming within a
new word-line.
5. Some EFP performance degradation may occur if block cycling exceeds 10.
Datasheet
79
Intel® Wireless Flash Memory (W18)
11.5
Reset Specifications
Table 29. Reset Specifications
#
Parameter1
Symbol
P1
tPLPH
P2
tPLRH
P3
tVCCPH
RST# Low to Reset during Read
Notes
Min
1, 2, 3, 4
100
Max
Unit
ns
RST# Low to Reset during Block Erase
1, 3, 4, 5
20
µs
RST# Low to Reset during Program
1, 3, 4, 5
10
µs
VCC Power Valid to Reset
1,3,4,5,6
60
µs
NOTES:
1. These specifications are valid for all product versions (packages and speeds).
2. The device may reset if tPLPH< tPLPHMin, but this is not guaranteed.
3. Not applicable if RST# is tied to VCC.
4. Sampled, but not 100% tested.
5. If RST# is tied to VCC, the device is not ready until tVCCPH occurs after when VCC ≥ VCCMin.
6. If RST# is tied to any supply/signal with VCCQ voltage levels, the RST# input voltage must not exceed VCC until VCC ≥
VCCMin.
Figure 33. Reset Operations Waveforms
P1
(A) Reset during
read mode
RST# [P]
VIL
P2
(B) Reset during
program or block erase
P1 ≤ P2
RST# [P]
Abort
Complete
R5
VIH
VIL
P2
(C) Reset during
program or block erase
P1 ≥ P2
R5
VIH
RST# [P]
Abort
Complete
R5
VIH
VIL
P3
(D) VCC Power-up to
RST# high
80
VCC
VCC
0V
Datasheet
Intel® Wireless Flash Memory (W18)
11.6
AC I/O Test Conditions
Figure 34. AC Input/Output Reference Waveform
VCCQ
Input
Test Points
VCCQ /2
VCCQ/2
Output
0V
NOTE: Input timing begins, and output timing ends, at VCCQ/2. Input rise and fall times (10% to 90%) < 5 ns.
Worst case speed conditions are when VCC = VCCMin.
Figure 35. Transient Equivalent Testing Load Circuit
VCCQ
R1
Device
Under Test
Out
CL
R2
NOTE: See Table 17 for component values.
Table 30. Test Configuration Component Values for Worst Case Speed Conditions
Test Configuration
CL (pF)
R1 (kΩ)
R2 (kΩ)
VCCQMin-Extended (1.35 V) Standard Test
30
13.5
13.5
VCCQMin (1.7 V) Standard Test
30
16.7
16.7
NOTE: CL includes jig capacitance.
Figure 36. Clock Input AC Waveform
R201
CLK [C]
VIH
VIL
R202
Datasheet
R203
81
Intel® Wireless Flash Memory (W18)
11.7
Device Capacitance
TA = +25 °C, f = 1 MHz
Parameter§
Typ
Max
Unit
Condition
Input Capacitance
6
8
pF
VIN = 0.0 V
COUT
Output Capacitance
8
12
pF
VOUT = 0.0 V
CCE
CE# Input Capacitance
10
12
pF
VIN = 0.0 V
Symbol
CIN
§
Sampled, not 100% tested.
82
Datasheet
Intel® Wireless Flash Memory (W18)
Appendix A Write State Machine States
This table shows the command state transitions based on incoming commands. Only one partition
can be actively programming or erasing at a time.
Figure 37. Write State Machine — Next State Table (Sheet 1 of 2)
Chip Next State after Command Input
Write State Machine (WSM) Next State Table
Current Chip
State
(8)
Read
Array
(3)
Setup
(4,5)
Erase
Setup
(4,5)
Enhanced BE Confirm,
Factory P/E Resume,
Pgm
ULB
Setup
Ready
(4)
(FFH)
(10H/40H)
(20H)
(30H)
Ready
Program
Setup
Erase
Setup
EFP
Setup
Lock/CR Setup
OTP
Program
Ready (Lock Error)
Confirm
(9)
(D0H)
Program/
Erase
Suspend
Read
Status
(B0H)
(70H)
(6)
Register
(50H)
Read
ID/Query
(90H, 98H)
Ready
Ready
Setup
Clear
Status
Ready (Lock Error)
OTP Busy
Busy
Setup
Program
Program Busy
Busy
Program Busy
Program Suspend
Pgm Busy
Setup
Ready (Error)
Erase Busy
Busy
Suspend
Erase
Suspend
Pgm in
Erase
Susp Setup
Erase Suspend
Pgm Susp in
Erase Susp
Program in Erase Suspend Busy
Program in Erase Suspend Busy
Program Suspend in Erase Suspend
Pgm in Erase
Susp Busy
Program Suspend in Erase Suspend
Erase Suspend (Lock Error)
Erase Susp
Erase Suspend
(Lock Error)
EFP Busy
Ready (Error)
Lock/CR Setup in Erase
Suspend
Enhanced
Factory
Program
Erase Busy
Erase Busy
Program in Erase Suspend Busy
Busy
Suspend
Ready (Error)
Erase Susp
Erase Suspend
Setup
Program Busy
Program Suspend
Erase Busy
Erase
Program in
Erase Suspend
Pgm Susp
Suspend
Setup
Ready (Error)
(7)
EFP Busy
EFP Busy
EFP Verify
Verify Busy
(7)
Output Next State Table
(1)
Output Next State after Command Input
Pgm Setup,
Erase Setup,
OTP Setup,
Pgm in Erase Susp Setup,
EFP Setup,
EFP Busy,
Verify Busy
Status
Lock/CR Setup,
Lock/CR Setup in Erase Susp
Status
OTP Busy
Ready,
Pgm Busy,
Pgm Suspend,
Erase Busy,
Erase Suspend,
Pgm In Erase Susp Busy,
Pgm Susp In Erase Susp
Datasheet
Status
Array
(3)
Status
Output does not change
Status
Output
does not
change
ID/Query
83
Intel® Wireless Flash Memory (W18)
Figure 37. Write State Machine — Next State Table (Sheet 2 of 2)
Chip Next State after Command Input
Write State Machine (WSM) Next State Table
Current Chip
State
(8)
Lock,
Unlock,
Lock-down,
CR setup
Setup
(5)
(9)
Confirm
(5)
(60H)
(C0H)
Ready
Lock/CR
Setup
OTP
Setup
Lock/CR Setup
Ready (Lock Error)
OTP
LockDown
Block
Lock
Block
OTP
Confirm
(01H)
Write CR
Confirm
(9)
(9)
(2FH)
(03H)
Enhanced
Fact Pgm
Exit (blk add
<> WA0)
(XXXXH)
Illegal
commands or
EFP data
(2)
(other codes)
Ready
Ready
Ready
Setup
Ready
N/A
Ready (Lock Error)
OTP Busy
Busy
Program
Ready
Setup
Program Busy
N/A
Busy
Program Busy
Ready
Suspend
Program Suspend
Setup
Ready (Error)
Busy
Erase
Suspend
Program in
Erase Suspend
N/A
Erase Busy
Lock/CR
Setup in
Erase Susp
Erase Busy
Erase Suspend
Setup
Program in Erase Suspend Busy
Busy
Program in Erase Suspend Busy
Suspend
Lock/CR Setup in Erase
Suspend
Enhanced
Factory
Program
WSM
Operation
Completes
Ready
N/A
Erase
Suspend
Program Suspend in Erase Suspend
Erase Suspend
(Lock Error)
Erase Susp Erase Susp Erase Susp
Setup
Erase Suspend (Lock Error)
N/A
Ready (Error)
EFP Busy
EFP Busy
EFP Verify
(7)
Verify Busy
(7)
(7)
EFP Verify
EFP Busy
Ready
EFP Verify
(7)
Ready
Output Next State Table
(1)
Output Next State after Command Input
Pgm Setup,
Erase Setup,
OTP Setup,
Pgm in Erase Susp Setup,
EFP Setup,
EFP Busy,
Verify Busy
Status
Lock/CR Setup,
Lock/CR Setup in Erase Susp
Status
Array
Status
OTP Busy
Ready,
Pgm Busy,
Pgm Suspend,
Erase Busy,
Erase Suspend,
Pgm In Erase Susp Busy,
Pgm Susp In Erase Susp
Status
Output does not change
Array
Output does
not change
Output does
not change
NOTES:
1. The output state shows the type of data that appears at the outputs if the partition address is the same as the command
address.
A partition can be placed in Read Array, Read Status or Read ID/CFI, depending on the command issued.
Each partition stays in its last output state (Array, ID/CFI or Status) until a new command changes it. The next WSM state does
not depend on the partition's output state.
For example, if partition #1's output state is Read Array and partition #4's output state is Read Status, every read from partition
#4 (without issuing a new command) outputs the Status register.
84
Datasheet
Intel® Wireless Flash Memory (W18)
2. Illegal commands are those not defined in the command set.
3. All partitions default to Read Array mode at power-up. A Read Array command issued to a busy partition results in undermined
data when a partition address is read.
4. Both cycles of 2 cycles commands should be issued to the same partition address. If they are issued to different partitions, the
second write determines the active partition. Both partitions will output status information when read.
5. If the WSM is active, both cycles of a 2 cycle command are ignored. This differs from previous Intel devices.
6. The Clear Status command clears status register error bits except when the WSM is running (Pgm Busy, Erase Busy, Pgm Busy
In Erase Suspend, OTP Busy, EFP modes) or suspended (Erase Suspend, Pgm Suspend, Pgm Suspend In Erase Suspend).
7. EFP writes are allowed only when status register bit SR.0 = 0. EFP is busy if Block Address = address at EFP Confirm
command. Any other commands are treated as data.
8. The "current state" is that of the WSM, not the partition.
9. Confirm commands (Lock Block, Unlock Block, Lock-down Block, Configuration Register) perform the operation and then move
to the Ready State.
10.In Erase suspend, the only valid two cycle commands are "Program Word", "Lock/Unlock/Lockdown Block", and "CR Write".
Both cycles of other two cycle commands ("OEM CAM program & confirm", "Program OTP & confirm", "EFP Setup & confirm",
"Erase setup & confirm") will be ignored. In Program suspend or Program suspend in Erase suspend, both cycles of all two
cycle commands will be ignored.
Datasheet
85
Appendix B Common Flash Interface
This appendix defines the data structure or “database” returned by the Common Flash Interface
(CFI) Query command. System software should parse this structure to gain critical information
such as block size, density, x8/x16, and electrical specifications. Once this information has been
obtained, the software will know which command sets to use to enable flash writes, block erases,
and otherwise control the flash component. The Query is part of an overall specification for
multiple command set and control interface descriptions called Common Flash Interface, or CFI.
B.1
Query Structure Output
The Query database allows system software to obtain information for controlling the flash device.
This section describes the device’s CFI-compliant interface that allows access to Query data.
Query data are presented on the lowest-order data outputs (DQ0-7) only. The numerical offset
value is the address relative to the maximum bus width supported by the device. On this family of
devices, the Query table device starting address is a 10h, which is a word address for x16 devices.
For a word-wide (x16) device, the first two Query-structure bytes, ASCII “Q” and “R,” appear on
the low byte at word addresses 10h and 11h. This CFI-compliant device outputs 00h data on upper
bytes. The device outputs ASCII “Q” in the low byte (DQ0-7) and 00h in the high byte (DQ8-15).
At Query addresses containing two or more bytes of information, the least significant data byte is
presented at the lower address, and the most significant data byte is presented at the higher address.
In all of the following tables, addresses and data are represented in hexadecimal notation, so the
“h” suffix has been dropped. In addition, since the upper byte of word-wide devices is always
“00h,” the leading “00” has been dropped from the table notation and only the lower byte value is
shown. Any x16 device outputs can be assumed to have 00h on the upper byte in this mode.
Table 31. Summary of Query Structure Output as a Function of Device and Mode
Hex
Offset
00010:
00011:
00012:
Device
Device Addresses
Hex
Code
51
52
59
ASCII
Value
"Q"
"R"
"Y"
Table 32. Example of Query Structure Output of x16- and x8 Devices
Offset
AX–A0
00010h
00011h
00012h
00013h
00014h
00015h
00016h
00017h
00018h
...
Word Addressing:
Hex Code
D15–D0
0051
0052
0059
P_IDLO
P_IDHI
PLO
PHI
A_IDLO
A_IDHI
...
Value
"Q"
"R"
"Y"
PrVendor
ID #
PrVendor
TblAdr
AltVendor
ID #
...
Offset
AX–A0
00010h
00011h
00012h
00013h
00014h
00015h
00016h
00017h
00018h
...
Byte Addressing:
Hex Code
Value
D7–D0
51
"Q"
52
"R"
59
"Y"
P_IDLO
PrVendor
P_IDLO
ID #
P_IDHI
ID #
...
...
Intel® Wireless Flash Memory (W18)
B.2
Query Structure Overview
The Query command causes the flash component to display the Common Flash Interface (CFI)
Query structure or “database.” The structure sub-sections and address locations are summarized
below.
Table 33. Query Structure
Offset
00000h
00001h
(2)
(BA+2)h
00004-Fh
00010h
0001Bh
00027h
(3)
P
Sub-Section Name
(1)
Description
Manufacturer Code
Device Code
Block Status register
Block-specific information
Reserved
Reserved for vendor-specific information
CFI query identification string
Command set ID and vendor data offset
System interface information
Device timing & voltage information
Device geometry definition
Flash device layout
Vendor-defined additional information specific
Primary Intel-specific Extended Query Table
to the Primary Vendor Algorithm
NOTES:
1. Refer to the Query Structure Output section and offset 28h for the detailed definition of offset address as a
function of device bus width and mode.
2. BA = Block Address beginning location (i.e., 08000h is block 1’s beginning location when the block size is
32K-word).
3. Offset 15 defines “P” which points to the Primary Intel-specific Extended Query Table.
B.3
Block Status Register
The Block Status Register indicates whether an erase operation completed successfully or whether
a given block is locked or can be accessed for flash program/erase operations.
Block Erase Status (BSR.1) allows system software to determine the success of the last block erase
operation. BSR.1 can be used just after power-up to verify that the VCC supply was not
accidentally removed during an erase operation.
Table 34. Block Status Register
Offset
Length
Description
(1)
(BA+2)h
1
Block Lock Status Register
BSR.0 Block lock status
0 = Unlocked
1 = Locked
BSR.1 Block lock-down status
0 = Not locked down
1 = Locked down
BSR 2–7: Reserved for future use
Add.
Value
BA+2 --00 or --01
BA+2 (bit 0): 0 or 1
BA+2 (bit 1): 0 or 1
BA+2
(bit 2–7): 0
NOTES:
1. BA = Block Address beginning location (i.e., 08000h is block 1’s beginning location when the block size is
32K-word).
B.4
CFI Query Identification String
The Identification String provides verification that the component supports the Common Flash
Interface specification. It also indicates the specification version and supported vendor-specified
command set(s).
Datasheet
87
Intel® Wireless Flash Memory (W18)
Table 35. CFI Identification
Offset
Length
Description
10h
3
Query-unique ASCII string “QRY“
13h
2
15h
2
Primary vendor command set and control interface ID code.
16-bit ID code for vendor-specified algorithms
Extended Query Table primary algorithm address
17h
2
19h
2
Alternate vendor command set and control interface ID code.
0000h means no second vendor-specified algorithm exists
Secondary algorithm Extended Query Table address.
0000h means none exists
Hex
Add. Code Value
10:
--51
"Q"
11:
--52
"R"
12:
--59
"Y"
13:
--03
14:
--00
15:
--39
16:
--00
17:
--00
18:
--00
19:
--00
1A:
--00
Table 36. System Interface Information
88
Offset
Length
Description
1Bh
1
1Ch
1
1Dh
1
1Eh
1
1Fh
20h
21h
22h
23h
24h
25h
26h
1
1
1
1
1
1
1
1
VCC logic supply minimum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 BCD volts
VCC logic supply maximum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 BCD volts
VPP [programming] supply minimum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 HEX volts
VPP [programming] supply maximum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 HEX volts
“n” such that typical single word program time-out = 2n µ-sec
n
“n” such that typical max. buffer write time-out = 2 µ-sec
n
“n” such that typical block erase time-out = 2 m-sec
n
“n” such that typical full chip erase time-out = 2 m-sec
n
“n” such that maximum word program time-out = 2 times typical
n
“n” such that maximum buffer write time-out = 2 times typical
n
“n” such that maximum block erase time-out = 2 times typical
n
“n” such that maximum chip erase time-out = 2 times typical
Hex
Add. Code Value
1B:
--17 1.7V
1C:
--19
1.9V
1D:
--B4
11.4V
1E:
--C6 12.6V
1F:
20:
21:
22:
23:
24:
25:
26:
--04 16µs
--00
NA
--0A
1s
--00
NA
--04 256µs
--00
NA
--03
8s
--00
NA
Datasheet
Intel® Wireless Flash Memory (W18)
B.5
Device Geometry Definition
Table 37. Device Geometry Definition
Offset
27h
Length
Description
n
“n” such that device size = 2 in number of bytes
1
Flash device interface code assignment:
"n" such that n+1 specifies the bit field that represents the flash
device width capabilities as described in the table:
28h
2Ah
2
2Ch
1
2Dh
31h
35h
Address
27:
28:
29:
2A:
2B:
2C:
2D:
2E:
2F:
30:
31:
32:
33:
34:
35:
36:
37:
38:
Datasheet
2
4
4
4
7
6
5
4
3
2
1
0
—
—
—
—
x64
x32
x16
x8
15
14
13
12
11
10
9
8
—
—
—
—
—
—
—
—
n
“n” such that maximum number of bytes in write buffer = 2
Number of erase block regions (x) within device:
1. x = 0 means no erase blocking; the device erases in bulk
2. x specifies the number of device regions with one or
more contiguous same-size erase blocks.
3. Symmetrically blocked partitions have one blocking region
Erase Block Region 1 Information
bits 0–15 = y, y+1 = number of identical-size erase blocks
bits 16–31 = z, region erase block(s) size are z x 256 bytes
Erase Block Region 2 Information
bits 0–15 = y, y+1 = number of identical-size erase blocks
bits 16–31 = z, region erase block(s) size are z x 256 bytes
Reserved for future erase block region information
32 Mbit
–B
–T
--16
--16
--01
--01
--00
--00
--00
--00
--00
--00
--02
--02
--07
--3E
--00
--00
--20
--00
--00
--01
--07
--3E
--00
--00
--20
--00
--00
--01
--00
--00
--00
--00
--00
--00
--00
--00
64 Mbit
–B
–T
--17
--17
--01
--01
--00
--00
--00
--00
--00
--00
--02
--02
--07
--7E
--00
--00
--20
--00
--00
--01
--07
--7E
--00
--00
--20
--00
--00
--01
--00
--00
--00
--00
--00
--00
--00
--00
Code
27:
See table below
28:
--01
x16
29:
2A:
2B:
2C:
--00
--00
--00
0
See table below
2D:
2E:
2F:
30:
31:
32:
33:
34:
35:
36:
37:
38:
See table below
See table below
See table below
128 Mbit
–B
–T
--18
--18
--01
--01
--00
--00
--00
--00
--00
--00
--02
--02
--07
--FE
--00
--00
--20
--00
--00
--01
--07
--FE
--00
--00
--20
--00
--00
--01
--00
--00
--00
--00
--00
--00
--00
--00
89
Intel® Wireless Flash Memory (W18)
B.6
Intel-Specific Extended Query Table
Table 38. Primary Vendor-Specific Extended Query
90
Offset(1)
P = 39h
(P+0)h
(P+1)h
(P+2)h
(P+3)h
(P+4)h
(P+5)h
(P+6)h
(P+7)h
(P+8)h
Length
(P+9)h
1
(P+A)h
(P+B)h
2
3
1
1
4
(P+C)h
1
(P+D)h
1
Description
(Optional flash features and commands)
Primary extended query table
Unique ASCII string “PRI“
Major version number, ASCII
Minor version number, ASCII
Optional feature and command support (1=yes, 0=no)
bits 10–31 are reserved; undefined bits are “0.” If bit 31 is
“1” then another 31 bit field of Optional features follows at
the end of the bit–30 field.
bit 0 Chip erase supported
bit 1 Suspend erase supported
bit 2 Suspend program supported
bit 3 Legacy lock/unlock supported
bit 4 Queued erase supported
bit 5 Instant individual block locking supported
bit 6 Protection bits supported
bit 7 Pagemode read supported
bit 8 Synchronous read supported
bit 9 Simultaneous operations supported
Supported functions after suspend: read Array, Status, Query
Other supported operations are:
bits 1–7 reserved; undefined bits are “0”
bit 0 Program supported after erase suspend
Block status register mask
bits 2–15 are Reserved; undefined bits are “0”
bit 0 Block Lock-Bit Status register active
bit 1 Block Lock-Down Bit Status active
VCC logic supply highest performance program/erase voltage
bits 0–3 BCD value in 100 mV
bits 4–7 BCD value in volts
VPP optimum program/erase supply voltage
bits 0–3 BCD value in 100 mV
bits 4–7 HEX value in volts
Add.
39:
3A:
3B:
3C:
3D:
3E:
3F:
40:
41:
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
bit 8
bit 9
42:
Hex
Code Value
--50
"P"
--52
"R"
--49
"I"
--31
"1"
--33
"3"
--E6
--03
--00
--00
=0
No
=1
Yes
=1
Yes
=0
No
=0
No
=1
Yes
=1
Yes
=1
Yes
=1
Yes
=1
Yes
--01
bit 0
43:
44:
bit 0
bit 1
45:
=1
--03
--00
=1
=1
--18
Yes
46:
--C0 12.0V
Yes
Yes
1.8V
Datasheet
Intel® Wireless Flash Memory (W18)
Table 39. Protection Register Information
(1)
Offset
P = 39h
(P+E)h
Length
(P+F)h
(P+10)h
(P+11)h
(P+12)h
4
1
Description
(Optional flash features and commands)
Number of Protection register fields in JEDEC ID space.
“00h,” indicates that 256 protection fields are available
Protection Field 1: Protection Description
This field describes user-available One Time Programmable
(OTP) Protection register bytes. Some are pre-programmed
with device-unique serial numbers. Others are user
programmable. Bits 0–15 point to the Protection register Lock
byte, the section’s first byte. The following bytes are factory
pre-programmed and user-programmable.
Hex
Add. Code Value
47:
--01
1
48:
49:
4A:
4B:
--80
--00
--03
--03
80h
00h
8 byte
8 byte
bits 0–7 = Lock/bytes Jedec-plane physical low address
bits 8–15 = Lock/bytes Jedec-plane physical high address
bits 16–23 = “n” such that 2n = factory pre-programmed bytes
bits 24–31 = “n” such that 2n = user programmable bytes
Table 40. Burst Read Information for Non-muxed Device
(1)
Offset
P = 39h
(P+13)h
Length
(P+14)h
1
(P+15)h
1
(P+16)h
(P+17)h
(P+18)h
1
1
1
1
Description
(Optional flash features and commands)
Page Mode Read capability
n
bits 0–7 = “n” such that 2 HEX value represents the number of
read-page bytes. See offset 28h for device word width to
determine page-mode data output width. 00h indicates no
read page buffer.
Number of synchronous mode read configuration fields that
follow. 00h indicates no burst capability.
Synchronous mode read capability configuration 1
Bits 3–7 = Reserved
n+1
bits 0–2 “n” such that 2 HEX value represents the
maximum number of continuous synchronous reads when
the device is configured for its maximum word width. A value
of 07h indicates that the device is capable of continuous
linear bursts that will output data until the internal burst
counter reaches the end of the device’s burstable address
space. This field’s 3-bit value can be written directly to the
Read Configuration Register bits 0–2 if the device is
configured for its maximum word width. See offset 28h for
word width to determine the burst data output width.
Synchronous mode read capability configuration 2
Synchronous mode read capability configuration 3
Synchronous mode read capability configuration 4
Hex
Add. Code Value
4C:
--03 8 byte
4D:
--04
4
4E:
--01
4
4F:
50:
51:
--02
--03
--07
8
16
Cont
Table 41. Partition and Erase-block Region Information
(1)
Offset
P = 39h
Description
Bottom
Top
(Optional flash features and commands)
(P+19)h (P+19)h Number of device hardware-partition regions within the device.
x = 0: a single hardware partition device (no fields follow).
x specifies the number of device partition regions containing
one or more contiguous erase block regions.
Datasheet
See table below
Address
Bot
Top
Len
1
52:
52:
91
Intel® Wireless Flash Memory (W18)
Partition Region 1 Information
(1)
Offset
P = 39h
Description
Bottom
Top
(Optional flash features and commands)
(P+1A)h (P+1A)h Number of identical partitions within the partition region
(P+1B)h (P+1B)h
(P+1C)h (P+1C)h Number of program or erase operations allowed in a partition
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+1D)h (P+1D)h Simultaneous program or erase operations allowed in other
partitions while a partition in this region is in Program mode
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+1E)h (P+1E)h Simultaneous program or erase operations allowed in other
partitions while a partition in this region is in Erase mode
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+1F)h (P+1F)h Types of erase block regions in this Partition Region.
x = 0 = no erase blocking; the Partition Region erases in bulk
x = number of erase block regions w/ contiguous same-size
erase blocks. Symmetrically blocked partitions have one
blocking region. Partition size = (Type 1 blocks)x(Type 1
block sizes) + (Type 2 blocks)x(Type 2 block sizes) +…+
(Type n blocks)x(Type n block sizes)
(P+20)h (P+20)h Partition Region 1 Erase Block Type 1 Information
(P+21)h (P+21)h
bits 0–15 = y, y+1 = number of identical-size erase blocks
(P+22)h (P+22)h
bits 16–31 = z, region erase block(s) size are z x 256 bytes
(P+23)h (P+23)h
(P+24)h (P+24)h Partition 1 (Erase Block Type 1)
Minimum block erase cycles x 1000
(P+25)h (P+25)h
(P+26)h (P+26)h Partition 1 (erase block Type 1) bits per cell; internal ECC
bits 0–3 = bits per cell in erase region
bit 4 = reserved for “internal ECC used” (1=yes, 0=no)
bits 5–7 = reserve for future use
(P+27)h (P+27)h Partition 1 (erase block Type 1) page mode and synchronous
mode capabilities defined in Table 10.
bit 0 = page-mode host reads permitted (1=yes, 0=no)
bit 1 = synchronous host reads permitted (1=yes, 0=no)
bit 2 = synchronous host writes permitted (1=yes, 0=no)
bits 3–7 = reserved for future use
(P+28)h
Partition Region 1 Erase Block Type 2 Information
(P+29)h
bits 0–15 = y, y+1 = number of identical-size erase blocks
(P+2A)h
bits 16–31 = z, region erase block(s) size are z x 256 bytes
(P+2B)h
(bottom parameter device only)
(P+2C)h
Partition 1 (Erase block Type 2)
(P+2D)h
Minimum block erase cycles x 1000
Partition 1 (Erase block Type 2) bits per cell
(P+2E)h
bits 0–3 = bits per cell in erase region
bit 4 = reserved for “internal ECC used” (1=yes, 0=no)
bits 5–7 = reserve for future use
Partition 1 (Erase block Type 2) pagemode and synchronous
(P+2F)h
mode capabilities defined in Table 10
bit 0 = page-mode host reads permitted (1=yes, 0=no)
bit 1 = synchronous host reads permitted (1=yes, 0=no)
bit 2 = synchronous host writes permitted (1=yes, 0=no)
bits 3–7 = reserved for future use
92
See table below
Address
Bot
Top
Len
2
53:
53:
54:
54:
1
55:
55:
1
56:
56:
1
57:
57:
1
58:
58:
4
1
59:
5A:
5B:
5C:
5D:
5E:
5F:
59:
5A:
5B:
5C:
5D:
5E:
5F:
1
60:
60:
4
1
61:
62:
63:
64:
65:
66:
67:
1
68:
2
2
Datasheet
Intel® Wireless Flash Memory (W18)
Partition Region 2 Information
(1)
Offset
P = 39h
Description
Bottom
Top
(Optional flash features and commands)
(P+30)h (P+28)h Number of identical partitions within the partition region
(P+31)h (P+29)h
(P+32)h (P+2A)h Number of program or erase operations allowed in a partition
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+33)h
(P+34)h
(P+35)h
(P+36)h
(P+37)h
(P+38)h
(P+39)h
(P+3A)h
(P+3B)h
(P+3C)h
(P+3D)h
(P+3E)h
(P+3F)h
Datasheet
See table below
Address
Bot
Top
Len
2
69:
61:
6A:
62:
1
6B:
63:
(P+2B)h Simultaneous program or erase operations allowed in other
1
partitions while a partition in this region is in Program mode
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+2C)h Simultaneous program or erase operations allowed in other
1
partitions while a partition in this region is in Erase mode
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+2D)h Types of erase block regions in this Partition Region.
1
x = 0 = no erase blocking; the Partition Region erases in bulk
x = number of erase block regions w/ contiguous same-size
erase blocks. Symmetrically blocked partitions have one
blocking region. Partition size = (Type 1 blocks)x(Type 1
block sizes) + (Type 2 blocks)x(Type 2 block sizes) +…+
(Type n blocks)x(Type n block sizes)
(P+2E)h Partition Region 2 Erase Block Type 1 Information
4
(P+2F)h
bits 0–15 = y, y+1 = number of identical-size erase blocks
(P+30)h
bits 16–31 = z, region erase block(s) size are z x 256 bytes
(P+31)h
(P+32)h Partition 2 (Erase block Type 1)
2
(P+33)h
Minimum block erase cycles x 1000
(P+34)h Partition 2 (Erase block Type 1) bits per cell
1
bits 0–3 = bits per cell in erase region
bit 4 = reserved for “internal ECC used” (1=yes, 0=no)
bits 5–7 = reserve for future use
(P+35)h Partition 2 (erase block Type 1) pagemode and synchronous
1
mode capabilities as defined in Table 10.
bit 0 = page-mode host reads permitted (1=yes, 0=no)
bit 1 = synchronous host reads permitted (1=yes, 0=no)
bit 2 = synchronous host writes permitted (1=yes, 0=no)
bits 3–7 = reserved for future use
(P+36)h Partition Region 2 Erase Block Type 2 Information
4
(P+37)h
bits 0–15 = y, y+1 = number of identical-size erase blocks
(P+38)h
bits 16–31 = z, region erase block(s) size are z x 256 bytes
(P+39)h
(P+3A)h Partition 2 (Erase Block Type 2)
2
(P+3B)h
Minimum block erase cycles x 1000
(P+3C)h Partition 2 (Erase Block Type 2) bits per cell
1
bits 0–3 = bits per cell in erase region
bit 4 = reserved for “internal ECC used” (1=yes, 0=no)
bits 5–7 = reserved for future use
(P+3D)h Partition 2 (Erase block Type 2) pagemode and synchronous
1
mode capabilities as defined in Table 10.
bit 0 = page-mode host reads permitted (1=yes, 0=no)
bit 1 = synchronous host reads permitted (1=yes, 0=no)
bit 2 = synchronous host writes permitted (1=yes, 0=no)
bits 3–7 = reserved for future use
(P+3E)h Features Space definitions (Reserved for future use)
TBD
(P+3F)h Reserved for future use
Resv'd
6C:
64:
6D:
65:
6E:
66:
6F:
70:
71:
72:
73:
74:
75:
67:
68:
69:
6A:
6B:
6C:
6D:
76:
6E:
6F:
70:
71:
72:
73:
74:
75:
76:
77:
78:
77:
78:
93
Intel® Wireless Flash Memory (W18)
Partition and Erase-block Region Information
Address
52:
53:
54:
55:
56:
57:
58:
59:
5A:
5B:
5C:
5D:
5E:
5F:
60:
61:
62:
63:
64:
65:
66:
67:
68:
69:
6A:
6B:
6C:
6D:
6E:
6F:
70:
71:
72:
73:
74:
75:
76:
64Mbit
32 Mbit
–B
--02
--01
--00
--11
--00
--00
--02
--07
--00
--20
--00
--64
--00
--01
--03
--06
--00
--00
--01
--64
--00
--01
--03
--07
--00
--11
--00
--00
--01
--07
--00
--00
--01
--64
--00
--01
--03
–T
--02
--07
--00
--11
--00
--00
--01
--07
--00
--00
--01
--64
--00
--01
--03
--01
--00
--11
--00
--00
--02
--06
--00
--00
--01
--64
--00
--01
--03
--07
--00
--20
--00
--64
--00
--01
--03
–B
--02
--01
--00
--11
--00
--00
--02
--07
--00
--20
--00
--64
--00
--01
--03
--06
--00
--00
--01
--64
--00
--01
--03
--0F
--00
--11
--00
--00
--01
--07
--00
--00
--01
--64
--00
--01
--03
–T
--02
--0F
--00
--11
--00
--00
--01
--07
--00
--00
--01
--64
--00
--01
--03
--01
--00
--11
--00
--00
--02
--06
--00
--00
--01
--64
--00
--01
--03
--07
--00
--20
--00
--64
--00
--01
--03
128Mbit
–B
–T
--02
--02
--01
--1F
--00
--00
--11
--11
--00
--00
--00
--00
--02
--01
--07
--07
--00
--00
--20
--00
--00
--01
--64
--64
--00
--00
--01
--01
--03
--03
--06
--01
--00
--00
--00
--11
--01
--00
--64
--00
--00
--02
--01
--06
--03
--00
--1F
--00
--00
--01
--11
--64
--00
--00
--00
--01
--01
--03
--07
--07
--00
--00
--00
--20
--01
--00
--64
--64
--00
--00
--01
--01
--03
--03
NOTES:
1. The variable P is a pointer which is defined at CFI offset 15h.
2. TPD - Top parameter device; BPD - Bottom parameter device.
3. Partition: Each partition is 4Mb in size. It can contain main blocks OR a combination of both main and
parameter blocks.
4. Partition Region: Symmetrical partitions form a partition region. (there are two partition regions, A. contains
all the partitions that are made up of main blocks only. B. contains the partition that is made up of the
parameter and the main blocks.
94
Datasheet
Intel® Wireless Flash Memory (W18)
Appendix C Mechanical Specifications
C.1
W18 – .18 µm Lithography
Figure 38. 64-Mb
µBGA*CSP Package Drawing and Dimensions
P in # 1
In d ic a to r
s
D
1
2
3
4
5
6
7
P in # 1
C o rn e r
1
s2
8
8
7
6
5
4
3
2
1
A
A
B
B
C
D
C
D
E
E
E
F
F
G
G
e
b
T o p V ie w - S ilico n b a ck s id e
B o tto m V ie w - B u m p s id e U p
C o m p le te In k M a rk N o t
A1
A2
A
S e a ti
Y
P la n
S id e
Package Height
Ball Height
Package Body Thickness
Ball (Lead) Width
Package Body Width
Package Body Length
Pitch
Ball (Lead) Count
Seating Plane Coplanarity
Corner to Ball A1 Distance Along D
Corner to Ball A1 Distance Along E
Datasheet
Symbol
A
A1
A2
b
D
E
[e]
N
Y
S1
S2
Millimeters
Min
0.850
0.150
0.612
0.300
7.600
8.900
1.125
2.150
Nom
Max
1.000
0.712
0.350
7.700
9.000
0.750
56
0.812
0.400
7.800
9.100
Inches
Min
0.0335
0.0059
0.0241
0.0118
0.2992
0.3503
0.100
1.325
2.350
0.0443
0.0846
1.225
2.250
Notes
Nom
Max
0.0394
0.0280
0.0138
0.3031
0.3543
0.0295
56
0.0320
0.0157
0.3071
0.3583
0.0482
0.0886
0.0039
0.0522
0.0925
95
Intel® Wireless Flash Memory (W18)
Figure 39. 32-Mb VFBGA Package Drawing
Ball A1
Corner
Ball A1
Corner
S1
D
1
E
2
3
4
5
6
7
8
8
A
A
B
B
C
C
D
D
E
E
F
F
G
G
7
6
5
4
3
2
1
S2
e
b
To p View - Bump Side Down
Bottom View - Ball Side Up
A1
A2
A
S eating
Y
P lane
Side V iew
Note: Drawing not to scale
Figure 40. 128-Mb VFBGA Package Drawing
Ball A1
Corner
1
E
S1
D
2
3
4
5
6
7
8
9
10
10
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
J
J
9 8
7
6
5
4
3
Ball A1
Corner
S2
2 1
e
b
Top View - Bump Side
Down
Bottom View - Ball Side
Up
A1
A2
A
Seating
Plane
Y
Side View
Note: Drawing not to scal e
96
Datasheet
Intel® Wireless Flash Memory (W18)
Table 42. 32-Mbit and 128-Mbit VFBGA Package Dimensions
Millimeters
Dimension
Min
Datasheet
Inches
Symbol
Nom
Max
Min
1.000
0.0335
Nom
Max
Package Height
A
0.850
0.0394
Ball Height
A1
0.150
Package Body Thickness
A2
0.615
0.665
0.715
0.0242
0.0262
0.0281
Ball (Lead) Width
b
0.325
0.375
0.425
0.0128
0.0148
0.0167
Package Body Width 32Mb
D
7.600
7.700
7.800
0.2992
0.3031
0.3071
Package Body Length32Mb
E
8.900
9.000
9.100
0.3503
0.3543
0.3583
Package Body Width 128Mb
D
12.400
12.500
12.600
0.4882
0.4921
0.4961
Package Body Length 128Mb
E
11.900
12.000
12.100
0.4685
0.4724
0.4764
Pitch
[e]
0.750
0.0295
Ball (Lead) Count 32Mb
N
56
56
Ball (Lead) Count 128Mb
N
60
Seating Plane Coplanarity
Y
Corner to Ball A1 Distance Along D
32Mb
S1
1.125
1.225
1.325
0.0443
0.0482
0.0522
Corner to Ball A1 Distance Along E
32Mb
S2
2.150
2.250
2.350
0.0846
0.0886
0.0925
Corner to Ball A1 Distance Along D
128Mb
S1
2.775
2.875
2.975
0.1093
0.1132
0.1171
Corner to Ball A1 Distance Along E
128Mb
S2
2.900
3.000
3.1000
0.1142
0.1181
0.1220
0.0059
60
0.100
0.0039
97
Intel® Wireless Flash Memory (W18)
C.2
W18 – .13 µm Lithography
Figure 41. 32-,
64- and 128-Mb VF BGA*CSP Package Drawing
B all A 1
Corner
B all A 1
Corner
D
1
E
2
3
4
S1
5
6
7
8
8
A
A
B
B
C
C
D
D
E
E
F
F
G
G
7
6
5
4
3
2
S2
1
e
b
Top V iew - Bump S ide Dow n
Bottom Vie w - Ba ll Sid e Up
A1
A2
A
S eating
Y
P lane
Table 43. 32-Mbit, 64-Mbit, and 128-Mbit VFBGA Package Dimensions
Millimeters
Dimension
Min
98
Inches
Symbol
Package Height
A
Ball Height
A1
Nom
Max
Min
Nom
1.000
0.150
Max
0.0394
0.0059
Package Body Thickness
A2
Ball (Lead) Width
b
0.325
0.375
0.425
0.0128
0.0148
0.0167
Package Body Width (32Mb,
64Mb)
D
7.600
7.700
7.800
0.2992
0.3031
0.3071
Package Body Width (128Mb)
D
10.900
11.000
11.100
0.4291
0.4331
0.4370
Package Body Length (32Mb,
64Mb, 128Mb)
E
8.900
9.000
9.100
0.3504
0.3543
0.3583
Pitch
[e]
0.750
Ball (Lead) Count
N
56
Seating Plane Coplanarity
Y
Corner to Ball A1 Distance
Along D (32Mb, 64Mb)
S1
1.125
1.225
1.325
0.0443
0.0482
0.0522
Corner to Ball A1 Distance
Along D (128Mb)
S1
2.775
2.2875
2.975
0.1093
0.1132
0.1171
Corner to Ball A1 Distance
Along E (32Mb, 64Mb,128Mb)
S2
2.150
2.250
2.350
0.0846
0.0886
0.0925
0.665
0.0262
0.0295
56
0.100
0.0039
Datasheet
Intel® Wireless Flash Memory (W18)
Figure 42. 128Mbit QUAD+ Package Drawing
S1
A1 Index
Mark
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
S2
A
A
B
B
C
C
D
D
E
E
F
D
F
G
G
H
H
J
J
K
K
L
L
M
M
e
b
E
Bottom View - Ball Up
Top View - Ball Down
A2
A1
A
Y
Drawing not to scale.
Dimensions
Package Height
Ball Height
Package Body Thickness
Ball (Lead) Width
Package Body Length
Package Body Width
Pitch
Ball (Lead) Count
Seating Plane Coplanarity
Corner to Ball A1 Distance Along E
Corner to Ball A1 Distance Along D
Datasheet
Symbol
A
A1
A2
b
D
E
e
N
Y
S1
S2
Min
Millimeters
Nom
Max
1.200
0.200
0.325
9.900
7.900
1.100
0.500
Notes
Min
Inches
Nom
Max
0.0472
0.0079
0.860
0.375
10.000
8.000
0.800
88
1.200
0.600
0.425
10.100
8.100
0.0128
0.3898
0.3110
0.100
1.300
0.700
0.0433
0.0197
0.0339
0.0148
0.3937
0.3150
0.0315
88
0.0472
0.0236
0.0167
0.3976
0.3189
0.0039
0.0512
0.0276
99
Intel® Wireless Flash Memory (W18)
Appendix D Ordering Information
Figure 43. VF BGA and µBGA Ordering Information
G E 2 8 F 6 4 0 W 1 8 T D 6 0
Access Speed (ns)
(60,80)
Package:
GE = 0.75 mm VF BGA
GT = 0.75 mm µ BGA*
Process Identifier:
C = 0.18 µ m
D = 0.13 µ m
Product Line Designator:
for all Intel Flash Products
Parameter Location:
T = Top Parameter
B = Bottom Parameter
Device Density:
320 = 32Mbit
640 = 64Mbit
128 = 128Mbit
Product Family:
W18 = Intel ® Wireless Flash
Memory
Flash 3 & 4
Flash 1 & 2
Flash 4
Flash 3
Flash 2
Flash 1
Figure 44. SCSP Ordering Information
R D 4 8 F 3 0 0 0 W 0 Y B Q 0
Package:
Device Details:
RD = SCSP, Leaded
PF = SCSP, Pb-Free
0 = Initial Version
Ballout Indicator:
Product Line:
Q= QUAD+
48F = Flash Only
Parameter Location:
Flash Density:
0 = No die
3 = 128 Mbit
Product Family Designator:
T = Top Parameter
B = Bottom Parameter
Voltage:
Y = 1.8 Volt I/O
W = Intel® Wireless Flash Memory
100
Datasheet