Z/A/X/DZ Common Accessories Ordering Information ■ Terminal Covers (Sold Separately) Common to Z, A, X, and DZ Models The Terminal Cover is secured using the switch’s side mounting screws and protects the casing and terminal wires from dust, vibration, or fingers, thus preventing terminal short-circuiting, ground faults, wire disconnection or improper connection, and electric shock accidents. Terminal Covers made of phenol resin have five or six thin wall sections. These sections can be torn open to provide holes for lead cables at desired points. Application Material Soldering terminal use Mounting direction Screw terminal use Remarks Model Phenol resin Side mounting AP-A AP-B --- Metal press mold Side mounting AP1-A AP1-B Used for AP-A and AP-B Vinyl chloride Side mounting AP-Z --- Note: Use the ‘Screw-terminal use’ Terminal Cover for DZ-series solder terminal models. ■ Separator (Sold Separately) Common to Z, A, X, and DZ Models Model: Separator for Z ■ Actuators (Sold Separately) Common to Z and X Models Pin Plunger Switches might need to be actuated by a cam or similar object, in which case, use one of the following Actuators according to the application. Actuator Common to Z and X models Hinge lever ZAA-1 Hinge roller lever ZAA-2 Panel mount plunger Short ZAQ-3 Medium ZAQ-2 Long ZAQ-1 Panel mount roller plunger ZAQ-22 Note: ZAQ-22 is constructed of ferrous material. Therefore, it cannot be used with the X Switch, because of the permanent magnet contained within those models. Use the ZAQ-22 external panel mount roller plunger only with the Z or DZ switch. Z/A/X/DZ Common Accessories 177 Dimensions Note: Unless otherwise specified, all units are in millimeters and a tolerance of ± 0.4 mm (±0.8 mm for the AP-Z) applies to all dimensions. ■ Terminal Covers 52.8 AP-A Soldering Terminal Use (Phenol Resin) 4.3+0.2 0 25.4 AP-B 4.3 +0.2 0 8 8 Soldering Terminal Use (Metal Press Mold) 20.2 2.15R 6.5 21 8 Note: The Cover has five thin, easy-to-separate portions for easy lead wire connections. 4.3+0.2 0 4.3 +0.2 0 8 16.3 6.4 2.15R AP1-A 53.8 25.4 4.3+0.2 0 Screw Terminal Use (Phenol Resin) 21 Note: The Cover has six thin, easy-to-separate portions for easy lead wire connections. 54.4 25.4 AP1-B 4.3 +0.2 0 8 55.4 25.4 4.3+0.2 0 Screw Terminal Use (Metal Press Mold) 4.3 +0.2 0 8 17.1 2.15R 21 2.15R 7.2 7 8.5 22.6 8.5 22.6 Note: 1. The Cover has five holes for easy lead wire connections. Note: 1. The Cover has six holes for easy lead wire connections. 2. AP1-A should be used with the AP-A AP-Z 2. AP1-B should be used with the AP-B Two, 4.2 dia. Pressure plate (t1 steel) Soldering or Screw Terminal Use (Vinyl Chloride) 53 25.4 21 Cable Pull-out Dimension 7 14 A-A' cross-section 15 21 8 dia. B-B' cross-section 13 6 dia. 39 46 Nut 12 14 M3 20 Phillips screw (with plane washer and nut) A A' B B' Note: A 6-dia. or 8-dia. cable can be used by cutting the cable pull-out hole to the size of the cable to be used. 12 ■ Separator SEPARATOR FOR Z Two, 4.5 dia. 13.5 27 25.4±0.2 49.2±0.5 178 Note: The separator’s material is EAVTC (Epoxide Alkyd Varnished Tetron Cloth) and its heat-resisting temperature is 130°C. 11.9 t = 0.38 Z/A/X/DZ Common Accessories ■ Actuators Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ± 0.4 mm applies to all dimensions. 2. These Actuators are not provided with Switches. Hinge Lever Two, M4 30 Two, M4 ZAA-1 Model Stainless steel 60R Z-15G-B OF max. RF min. PT max. OT min. MD max. 500 gf 170 gf 6 mm 12.7 mm 2.2 mm FP max. 32.9±1.6 mm X-10G-B 500 gf 170 gf 6 mm 12.7 mm 3.3 mm Note: This Actuator can be used with the Z-15G(-B) and X-10G(-B). When mounting the Switch, set the overtravel to between 32% and 100%, taking into consideration the operating body and the distance between the Actuator and the dog. Hinge Roller Lever Two, M4 30 Two, M4 ZAA-2 Model 9.5 dia. 4.8 (stainless-steel roller) Stainless steel 58.5R Z-15G-B X-10G-B 500 gf 170 gf 6 mm 12.7 mm 3.3 mm OF max. RF min. PT max. OT min. MD max. 500 gf 170 gf 6 mm 12.7 mm 2.2 mm FP max. 44.5±1.6 mm Note: This Actuator can be used with the Z-15G(-B) and X-10G(-B). When mounting the Switch, set the overtravel to between 32% and 100%, taking into consideration the operating body and the distance between the Actuator and the dog. Panel Mount Roller Lever ZAQ-22 48 PT 12.7 dia. (Note 1) 4.8 23.3±0.25 OP 1.6 (Note 3) 14.5 dia. 20.7 Two hex nuts 5-mm thickness, 19 mm between opposing edges With groove for roller penetration M12 1 mounting screw 18.9 23.9 (Note 2) 11.9 25.4±0.2 49.2 Two, M4 25 screws 20.7 Spring washer Note: 1. Stainless-steel pin plunger 2. Bronze frame 3. Incomplete screw section part with a maximum of 1.5 mm. Model ZAQ-22 Z-15E-B DZ-10G-B 1,131 gf 114 gf 2 mm 1 mm 0.46 mm OF max. RF min. PT max. OT min. MD max. 850 gf 114 gf 2 mm 3.58 mm 0.15 mm OP 37±0.8 mm 35.4±1.2 mm Note: This Actuator (panel mount roller plunger) can be used with standard pin plungers (Z-15G(-B), Z-15E(-B), and DZ-10G-1A(-1B)). The ZAQ-22 is constructed of ferrous material. Therefore, It cannot be used with X switches due to the permanent magnet used within those models. Z/A/X/DZ Common Accessories 179 Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ± 0.4 mm applies to all dimensions. 2. These Actuators are not provided with Switches. Short Panel Mount Plunger ZAQ-3 23.3 12SR 7.9 dia. Model M12 1 mounting screw (Note 1) 2 t 14 width across flats (Note 3) 14.5 dia. 2 t 15.6 width across flats Two M4 nuts Two M4 25 ± round head screw (Note 2) ZAQ-3 Z-15E-B X-10G-B 550 gf 114gf 1 mm 4.5 mm 0.2 mm OF max. RF min. PT max. OT min. MD max. 850 gf 114 gf 0.8 mm 4.8 mm 0.15 mm OP 27.8±1.5 mm Note: 1. Stainless-steel pin plunger 2. Bronze frame 3. Incomplete screw section part with a maximum of 1.5 mm Medium Panel Mount Plunger ZAQ-2 7.9 dia. 23.3 12SR Model M12 1 mounting screw 2 t 14 width across flats (Note 1) 2 t 15.6 width across flats (Note 3) 14.5 dia. Two M4 25 screw ZAQ-2 Z-15E-B X-10G-B 550 gf 114 gf 1 mm 4.5 mm 0.2 mm OF max. RF min. PT max. OT min. MD max. 850 gf 114 gf 0.8 mm 4.8 mm 0.15 mm OP 53.2±1.5 mm Note: 1. Stainless-steel pin plunger 2. Bronze frame 3. Incomplete screw section part with a maximum of 1.5 mm Two M4 nuts (Note 2) Long Panel Mount Plunger ZAQ-1 7.9 dia. Model 23.3 12SR (Note 1) M12 1 mounting screw 2 t 14 width across flats (Note 3) 14.5 dia. 2 t 15.6 width across flats Two, M4 25 screws (Note 2) ZAQ-1 Z-15E-B X-10G-B 550 gf 114 gf 1 mm 20.4 mm 0.2 mm OF max. RF min. PT max. OT min. MD max. 850 gf 114 gf 0.8 mm 20.6 mm 0.15 mm OP 69.1±1.5 mm Note: 1. Stainless-steel pin plunger 2. Bronze frame 3. Incomplete screw section part with a maximum of 1.5 mm Two, M4 nuts Note: Except for the ZAQ-22, these actuators (panel mount plungers) can be used with standard pin plunger versions of the Z and X models. (Z-15G(-B), Z-15E(-B), X-10G(-B)) 180 Z/A/X/DZ Common Accessories MEMO Z/A/X/DZ Common Accessories All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ON-LINE OMRON ELECTRONIC COMPONENTS LLC Global - http://www.omron.com USA - http://www.components.omron.com 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 Cat. No. X303-E-1 11/10 Specifications subject to change without notice Z/A/X/DZ Common Accessories Printed in USA