D2JW Sealed Subminiature Basic Switch Ultra-small and Highly Sealed ● Degree of protection conforms to JIS Waterproof standard and IEC IP67. (Excluding the terminals on terminal models) ● Wide range of operating temperatures from −40°C to +85°C. D 2 J W ● Gold-alloy crossbar contact and coil spring offer long durability and high contact reliability. RoHS Compliant Model Number Legend 1 @ 2 @ 3 D2JW-01@ 1. Actuator None : Pin plunger 2. Contact form 1: SPDT K1A : Short hinge lever 2: SPST-NC (Molded lead wire models only) 3: SPST-NO (Molded lead wire models only) K1 : Hinge lever K2 : Hinge roller Lever K3 : Simulated roller lever 3. Terminals None : Solder terminals -MD : Molded lead wires List of Models Actuator Pin plunger Terminals Contact form Solder terminals SPDT Molded lead wires Solder terminals Short hinge lever Molded lead wires Solder terminals Hinge Lever Models Molded lead wires Solder terminals Hinge Roller Lever Models Molded lead wires Solder terminals Simulated Roller Lever Models Molded lead wires Model D2JW-011 SPDT D2JW-011-MD SPST-NC D2JW-012-MD SPST-NO D2JW-013-MD SPDT D2JW-01K1A1 SPDT D2JW-01K1A1-MD SPST-NC D2JW-01K1A2-MD SPST-NO D2JW-01K1A3-MD SPDT D2JW-01K11 SPDT D2JW-01K11-MD SPST-NC D2JW-01K12-MD SPST-NO D2JW-01K13-MD SPDT D2JW-01K21 SPDT D2JW-01K21-MD SPST-NC D2JW-01K22-MD SPST-NO D2JW-01K23-MD SPDT D2JW-01K31 SPDT D2JW-01K31-MD SPST-NC D2JW-01K32-MD SPST-NO D2JW-01K33-MD Contact form ●SPDT COM NO NC (Black) (Blue) (Red) ●SPST-NC COM (Black) ●SPST-NO NC (Red) COM NO (Black) (Blue) The color in parentheses indicates the color of the lead wire. 1 D2JW Sealed Subminiature Basic Switch Contact Specifications Contact Characteristics Specification Crossbar Permissible operating speed Material Gold alloy Permissible operating frequency Gap (standard value) Inrush current 0.5 mm D 2 J W Mechanical Electrical NC 0.1A max. Insulation resistance NO 0.1A max. Contact resistance (initial value) Minimum applicable load (see note) 5 VDC 1 mA Dielectric strength * 1 Ratings Rated voltage Resistive load 30 VDC 0.1A 1 mm to 250 mm/s (for pin plunger models) 240 operations/min 30 operations/min 100 MΩ min. (at 500 VDC with insulation tester) Solder terminal models Molded lead wire models Mechanical Durability * 3 Electrical Degree of protection 140 mΩ max. Between terminals of the same polarity Between current-carrying metal parts and ground Between each terminal and non-current-carrying metal parts Vibration Malfunction resistance * 2 Durability Shock resistance Malfunction * 2 Note. The above rating values apply under the following test conditions. (1) Ambient temperature: 20±2°C (2) Ambient humidity: 65±5% (3) Operating frequency: 30 operations/min 100 mΩ max. Solder terminal models Molded lead wire models Ambient operating temperature Ambient operating humidity Weight 600 VAC 50/60 Hz 1min 1,000 VAC 50/60 Hz 1min 1,000 VAC 50/60 Hz 1min 10 to 55 Hz, 1.5 mm double amplitude 1,000 m/s2 {approx. 100G} max. 2 200 m/s {approx. 20G} max. 1,000,000 operations min. (60 operations/min) 100,000 operations min. (30 operations/min) IEC IP67 (excluding the terminals on terminal models) IEC IP67 −40°C to +85°C (at ambient humidity of 60% max.) (with no icing or condensation) 35% to 98% (for +5°C to +35°C) Approx. 0.6g (for pin plunger models with terminals) Note. The data given above are initial values. *1. The dielectric strength values shown apply for use with Separator (refer to page 4). *2. For the pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, they apply at the total travel position. Close or open circuit of the contact is 1ms max. *3. For testing conditions, consult your OMRON sales representative. Mounting Holes (Unit: mm) M2.3 mounting screw hole 4.8±0.1 Dimensions (Unit: mm) /Operating Characteristics Dimensions and operating characteristics of other actuator models for lead wire models are omitted in the illustration below, as the dimensions other than the termial part and operatiing characteristics is common with Solder terminal models. ●Pin plunger models D2JW-011 1.6 dia. Pretravel (PT) A Operating characteristics Operating Position (OP) Operating Force Releasing Force 9.4 12.3 Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 2.8 +0.05 2.35−0.025 1.3 1 2 2.5+0.05 −0.025 dia. OF Max. RF Min. 0.5 +0.05 2.35−0.025 dia. 0.4 Operating Position OP Operating Force Releasing Force OF Max. RF Min. 2.45 N {250 gf} 0.98 N {100 gf} 0.6 mm 0.3 mm 0.1 mm 8.1±0.3 mm 5.3±0.1 4.8±0.05 3.95 3.95 3.95 12.7 ●Short hinge lever models D2JW-01K1A1 1.8 7.95 Pretravel (PT) t0.3 Stainless-steel A lever R11.5 3 Operating Position (OP) 6.15 9.4 Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 12.3 2.8 +0.05 2.35−0.025 1.3 1 2 2.5+0.05 −0.025 dia. +0.05 2.35−0.025 dia. 4.8±0.05 3.95 3.95 3.95 12.7 Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note 2. The operating characteristics are for operation in the A direction ( ). 2 0.5 0.4 5.3±0.1 Operating Position OP 1.15 N {117 gf} 0.23 N {23 gf} 5.4 mm 0.7 mm 0.5 mm 8.4±0.8 mm D2JW ●Hinge lever models D2JW-01K11 Sealed Subminiature Basic Switch 7.95 1.8 A Pretravel (PT) t0.3 Stainless-steel lever R16.5 3 Operating Force Releasing Force Operating Position (OP) 6.15 9.4 Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 12.3 2.8 +0.05 2.35−0.025 1.3 2.5+0.05 −0.025 dia. 0.5 +0.05 dia. 2.35−0.025 1 2 OF Max. RF Min. Operating Position 0.4 OP 0.80 N {82 gf} 0.15 N {16 gf} 6.4 mm 1.4 mm 0.7 mm 8.4±0.8 mm D 2 J W 5.3±0.1 4.8±0.05 3.95 3.95 3.95 12.7 ●Simulated roller lever models D2JW-01K31 Pretravel (PT) 7.95 1.8 5.35 R1.3 1.3 1.9 t0.3 Stainless-steel lever 3 A Operating Force Releasing Force Operating Position (OP) 6.15 9.4 Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 12.3 2.8 +0.05 2.35−0.025 1.3 1 2 2.5+0.05 −0.025 dia. 0.5 +0.05 2.35−0.025 dia. OF Max. RF Min. 0.4 Operating Position OP Operating Force Releasing Force OF Max. RF Min. 0.95 N {97 gf} 0.19 N {20 gf} 5.5 mm 1.1 mm 0.6 mm 10.3±0.8mm 5.3±0.1 4.8±0.05 3.95 3.95 3.95 12.7 ●Hinge roller lever models D2JW-01K21 7.95 1.8 Pretravel (PT) 4.8×2.2 dia. Polyacetal resin roller A R13.5 Operating Position (OP) 6.15 9.4 Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 12.3 2.8 +0.05 2.35−0.025 1.3 1 2 2.5+0.05 −0.025 dia. +0.05 2.35−0.025 dia. 0.5 0.4 Operating Position OP Operating Force Releasing Force OF Max. RF Min. 0.98 N {100 gf} 0.19 N {20 gf} 5.2 mm 1.1 mm 0.5 mm 14.6±0.8 mm 5.3±0.1 4.8±0.05 3.95 3.95 3.95 12.7 ●Molded lead wire models D2JW-01@@@-MD Pretravel (PT) 1.6 dia. A 0.05 2.35−+0.025 dia. 2.35+−0.05 0.025 Operating Position (OP) 15.3 2.5+−0.05 0.025 dia. 4.8±0.05 3.95 Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 8.7 Operating Position OP 2.45 N {250 gf} 0.98 N {100 gf} 0.6 mm 0.3 mm 0.1 mm 8.1±0.3 mm AVS 0.3 300±10 5±2 Note. When ordering, replace @ with the code for the actuator and contact form that you need. COM NO NC (Black) (Blue) (Red) 12.7 5.3±0.1 Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note 2. The operating characteristics are for operation in the A direction ( ). 3 D2JW Sealed Subminiature Basic Switch Precautions ★Please refer to "Basic Switches Common Precautions" for correct use. Cautions ●Terminal Connection Correct Use ●Mounting Before soldering the lead wire to the terminal, first insert the lead wire conductor through the terminal hole. Complete the soldering at the iron tip temperature between 350 to 400°C within 3 seconds, and do not apply any external force D for 1 minute after soldering. Soldering at an excessively high 2 temperature or soldering for more than 3 seconds may J W deteriorate the characteristics of the Switch. Use M2.3 mounting screw with plane washers or spring washers to securely mount the Switch. Tighten the screws to a torque of 0.20 to 0.29 N·m {2 to 3 kgf·cm}. ●Separator When mounting the Switch on a metallic surface, be sure to provide a Separator between the Switch and the mounting plate. ●Wiring Molded Lead Wire Models ●Degree of Protection • The Switch was tested and found to meet the conditions necessary to meet the following standard given below. The test checks for water intrusion after immersion for a specified time period, not for switching operation underwater. JIS C0920: Degrees of protection provided by enclosures of electrical apparatus (IP Code) IEC 60529: Degrees of protection provided by enclosures (IP Code) Degree of protection: IP67 (check water intrusion after immersion for 30 min. submerged 1m underwater) When wiring molded lead wire models, ensure that there is no weight applied on the wire and that the wire is not bent. Otherwise, damage to the Switch or deterioration in the sealing may result. ●Protection Against Chemicals Prevent the Switch from coming into contact with oil or chemicals. Otherwise, damage to or deterioration of Switch materials may result. Separator (sold separately) SEPARATOR FOR D2JW 2-2.4±0.1 dia. 10.4 5.2 4.8±0.1 3.6 12 t=0.18 Note. The material of the separator is EAVTC (epoxy alkyd/varnish tetron cloth). • Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. • Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: Do not use this document to operate the Unit. OMRON Corporation ELECTRONIC AND MECHANICAL COMPONENTS COMPANY 4 Contact: www.omron.com/ecb Cat. No. B040-E1-03 0812(0207)(O)