SANYO LV5695P

Ordering number : ENA1972A
Monolithic Linear IC
LV5695P
For Car Audio Systems
Multi-Power Supply System IC
Overview
LV5695P is a multiple voltage regulator for car audio system, which allows reduction of quiescent current. This IC has 5
systems of voltage regulator pre-driver which a high side switch for external devices. The following protection circuits are
integrated: over current protector, overvoltage protector and Thermal Shut Down.
Features
• Quiescent current 50μA (Typ. when only VDD is in operation)
• Five channel regulator
For VDD: VOUT is 5.0V/3.3V(Operation always), IOmax is 300mA
For SWD5V: VOUT is 5.0V, IOmax is 500mA
For CD: VOUT is 8.0V, IOmax is 2000mA
For illumination: VOUT is 8.5V, IOmax is 500mA
For audio systems: VOUT is 8.45V, IOmax is 800mA
• Two high side switch:
AMP: Voltage difference between input and output is 0.5V, IOmax is 500mA
ANT: Voltage difference between input and output is 0.5V, IOmax is 350mA
• Over current protector
• Overvoltage protector (Without VDD-OUT) Clamp voltage is 28V (typical)
• Thermal Shut down 175ºC (typical)
• Pch-LDMOS is used for power output block.
(Warning) The protector functions only improve the IC’s tolerance and they do not guarantee the safety of the IC if used under the
conditions out of safety range or ratings. Use of the IC such as use under over current protection range or thermal shutdown state may
degrade the IC’s reliability and eventually damage the IC.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment. The products mentioned herein
shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life,
aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system,
safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives
in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any
guarantee thereof. If you should intend to use our products for new introduction or other application different
from current conditions on the usage of automotive device, communication device, office equipment, industrial
equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the
intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely
responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer ' s products or
equipment.
O2611 SY 20111018-S00003/82411 SY 20110718-S00006 No.A1972-1/13
LV5695P
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Conditions
Conditions
Power supply voltage
VCC max
Power dissipation
Pd max
IC unit
(*1)
At using Al heat sink (50×50×1.5mm3)
Ratings
Unit
At infinity heat sink
36
V
1.5
W
5.6
W
32.5
W
50
V
Peak voltage
VCC peak
Regarding Bias wave, refer to below the pulse.
Operating temperature
Topr
-40 to +85
°C
Storage temperature
Tstg
-55 to +150
°C
Junction temperature
Tj max
150
°C
*1 : Ta ≤ 25°C
Recommended Operating range at Ta = 25°C
Parameter
Conditions
Power supply voltage rating 1
VDD output ON, SWD output ON
Power supply voltage rating 2
ILM output ON
Power supply voltage rating 3
Audio output ON, CD output ON
Ratings
Unit
7 to 16
V
10.3 to 16
V
10 to 16
V
* VCC1 should be as follows: VCC1>VCC-0.7V
Electrical Characteristics at Ta = 25°C(*2), VCC = VCC1=14.4V
Parameter
Current drain
Symbol
ICC
Conditions
Ratings
min
typ
VDD no load, CTRL1/2/3 = ⎡L/L/L⎦
Unit
max
50
100
μA
0.3
V
CTRL1/2/3 Input
Low input voltage
VIL1
0
Middle input voltage 1
VIM1
0.8
1.06
1.4
V
Middle input voltage 2
VIM2
1.9
2.13
2.4
V
High input voltage
VIH
2.9
3.2
5.5
V
Input impedance
RIN
280
400
520
kΩ
Input voltage ≤ 3.3V
IKVDD input.
Low input voltage
VIL2
High input voltage
VIH2
IKVDD
-
-
0.7
V
VCC1-0.7
-
-
V
VDD output(5V/3.3V)
Output voltage
VO11
IO1 = 200mA, IKVDD = VCC1
4.85
5.0
5.15
V
VO12
IO1 = 200mA, IKVDD = GND
3.2
3.3
3.4
V
Output current
IO1
VO11 ≥ 4.7V, VO12 ≥ 3.1V
300
Line regulation
ΔVOLN1
7.5V < VCC1 < 16V, IO1 = 200mA
30
70
mV
Load regulation
ΔVOLD1
1mA < IO1 < 200mA
70
150
mV
Dropout voltage 1
VDROP1
IO1 = 200mA (VDD output 5V time)
0.8
1.6
V
Dropout voltage 2
VDROP1’
IO1 = 100mA (VDD output 5V time)
0.4
0.8
Ripple rejection
RREJ1
f = 120Hz, IO1 = 200mA
mA
30
40
8.196
8.45
V
dB
AUDIO (8.45V) Output ; CTRL2 = ⎡M1 or H⎦
AUDIO output voltage 1
VO3
IO3 = 650mA
AUDIO output current
IO3
VO3 ≥ 8.0V
Line regulation
ΔVOLN3
10V < VCC < 16V, IO3 = 650mA
Load regulation
ΔVOLD3
Dropout voltage 1
VDROP3
Dropout voltage 2
VDROP3’
IO3 = 200mA
Ripple rejection
RREJ3
f = 120Hz, IO3 = 650mA
8.7
800
V
mA
30
90
mV
1mA < IO3 < 650mA
100
200
mV
IO3 = 650mA
0.7
1.2
V
0.2
0.35
V
40
50
8.245
8.5
dB
ILM (8.5V) Output ; CTRL1 = ⎡M1 or H⎦
ILM output voltage
VO4
IO4 = 350mA
ILM output current
IO4
VO4 ≥ 8.1V
500
8.755
V
mA
Continued on next page.
No.A1972-2/13
LV5695P
Continued from preceding page.
Parameter
Symbol
Conditions
Ratings
min
typ
Unit
max
Line regulation
ΔVOLN4
10.8V < VCC < 16V, IO4 = 350mA
40
100
mV
Load regulation
ΔVOLD4
1mA < IO4 < 350mA
70
150
mV
Dropout voltage 1
VDROP4
IO4 = 350mA
1.0
1.5
V
0.3
0.6
Dropout voltage 2
VDROP4’
IO4 = 100mA
Ripple rejection
RREJ4
f = 120Hz, IO4 = 350mA
Output voltage
VO5
IO5 = 500mA
Output current
IO5
VCC-1.0 ≥ ΔVO5
Output voltage
VO6
IO6 = 300mA
Output current
IO6
VCC-1.0 ≥ ΔVO6
350
VO7
IO7 = 350mA
4.85
SWD output current
IO7
VO7 ≥ 4.7V
500
Line regulation
ΔVOLN7
Load regulation
40
50
V
dB
AMP_HS-SW; CTRL3 = ⎡M2 or H⎦
VCC-0.5
VCC-1.0
500
V
mA
ANT_HS-SW; CTRL3 = ⎡M1 or H⎦
VCC-0.5
VCC-1.0
V
mA
SWD5V; CTRL2 = ⎡M2 or H⎦
SWD output voltage
5.0
5.15
V
10V < VCC < 16V, IO7 = 350mA
30
70
mV
ΔVOLD7
1mA < IO7 < 350mA
70
150
mV
Dropout voltage
VDROP7
IO7 = 350mA
0.8
1.6
Ripple rejection
RREJ7
f = 120Hz, IO7 = 350mA
mA
40
50
8.0
V
dB
CD(8.0V output); CTRL1 = ⎡ M2 or H⎦
CD output voltage
VO81
IO8 = 1300mA
7.76
CD output current
IO8
VO81 ≥ 7.6V
2000
Line regulation
ΔVOLN8
10.5V < VCC < 16V, IO8 = 1300mA
Load regulation
ΔVOLD8
10mA < IO8 < 1300mA
Dropout voltage 1
VDROP8
IO8 = 1300mA
Dropout voltage 2
VDROP8’
IO8 = 350mA
0.35
0.7
Ripple rejection
RREJ8
f = 120Hz, IO8 = 1300mA
V
mA
40
40
8.24
100
mV
70
200
mV
1.3
1.95
V
50
V
dB
*2: The entire specification has been defined based on the tests performed under the conditions where Tj and Ta (=25°C) are almost equal. There tests were
performed with pulse load to minimize the increase of junction temperature (Tj).
No.A1972-3/13
LV5695P
Package Dimensions
unit : mm (typ)
3395
21.6
(20.0)
HEAT SPREADER
HEAT SINK
(15.8)
3.0
(11.0)
12.4
(9.05)
(14.55)
17.9
(9.6)
(R1.75)
3.35
0.4
1
15
(1.91)
1.27
2.54 2.54
0.7
SANYO : HZIP15J
• Allowable power dissipation derating curve
Pd max -- Ta
Allowable power dissipation, Pd max -- W
8
Aluminum heat sink mounting conditions
tightening torque : 39N⋅cm, using silicone grease
7
Aluminum heat sink (50 × 50 × 1.5mm3) when using
6
5.6
5
4
3
2
Independent IC
1.5
1
0
0
20
40
60
80
100
120
140 150 160
Ambient temperature, Ta -- °C
• Waveform applied during surge test
50V
90%
10%
16V
5msec
100msec
No.A1972-4/13
LV5695P
CTRL Pin Output Truth Table(Each output can be independently controlled by four value input.)
INAMP
INANT
CTRL3
AMP
ANT
L
L
L
OFF
OFF
L
H
M1
OFF
ON
H
L
M2
ON
OFF
H
H
H
ON
ON
CTRL2
SWD5V
AUDIO
CTRL1
CD
ILM
OFF
L
OFF
OFF
L
OFF
M1
OFF
ON
M1
OFF
ON
M2
ON
OFF
M2
ON
OFF
H
ON
ON
H
ON
ON
INAMP
INANT
CTL3
(Warning) Usage of CTRL2
When CTRL pin transits between L and M2, since it passes M1, ILM,/AUDIO/ANT is turned on for a moment. Likewise,
when CTRL pin transits between H and M1, since it passes M2, ILM/AUDIO/ANT is turned off for a moment.
To avoid operation failure by the above factors, please refer to the following precautions.
• Do not connect parasitic capacitor to CTRL as much as possible.
• If use of capacitor for CTRL is required, keep the resistance value as low as possible.
• Make sure that the output load capacitor has enough marjin against the voltage fluctuation due to instantaneous
ON/OFF.
No.A1972-5/13
LV5695P
z Block Diagram
VCC
AMP
out
AMP_SW(V CC -0.5V)
500mA
ANT
out
ANT_SW(VCC -0.5V)
350mA
Over
Voltage
Protection
Start
up
Vref
+
ILM output(8.5V)
500mA
+
CTRL1
CTRL2
AUDIO output(8.45V)
800mA
OUTPUT
Control
CTRL3
+
SWD output(5V)
500mA
Thermal
+
CD output(8V)
2000mA
Shut Down
VCC1(VDD power supply input)
GND
VCC
+
VDD output(3.3/5V)
300mA
IKVDD:VDD(3.3/5V) changeing pin
IKVDD=VCC1:5V
IKVDD=GND:3.3V
No.A1972-6/13
LV5695P
Pin Function
Pin No.
1
Pin name
ILM
Description
ILM output pin
ON when CTRL1 = M1, H
Equivalent Circuit
VCC
15
8.5V/0.5A
1
2
GND
3
CD
2
GND
15
VCC
GND pin
CD output pin
ON when CTRL1 = M2, H
8.0V/2A
3
2
4
CTRL1
CTRL1/2/3 input pin
6
CTRL2
Four values input
8
CTRL3
GND
15
VCC
4
6
8
2
5
AUDIO
AUDIO output pin
ON when CTRL2 = M1, H
15
GND
VCC
8.45V/0.8A
5
2
GND
Continued on next page.
No.A1972-7/13
LV5695P
Continued from preceding page.
Pin No.
7
Pin name
SWD
Description
SWD output pin
ON when CTRL2 = M2, H
Equivalent Circuit
VCC
15
5V/0.5A
7
2
9
ANT
ANT output pin
GND
VCC
15
ON when CTRL3 = M1, H
VCC-0.5V/350mA
EXT output pin
11
ON when CTRL2 = M2, H
VCC-0.5V/500mA
11 9
10
NC
(GND)
12
IKVDD
VDD voltage change control input pin
VCC1/GND
2
GND
14
VCC
12
2
13
VDD
VDD output pin
5.0V/0.3A(IKVDD = VCC1)
3.3V/0.3A(IKVDD = GND)
GND
VCC
14
13
2
14
VCC1
VDD power supply pin
15
VCC
Power supply pin
GND
VCC 15
2
14 VCC1
GND
No.A1972-8/13
LV5695P
Timing Chart
28V
VCC
(15PIN)
28V
VCC1
(14PIN)
5.8V
VDD output
(5V time)
(13PIN)
CTRL1 input
(4PIN)
H
M2
M1
L
H
CTRL2 input
(6PIN)
M2
M1
L
H
CTRL3 input
(8PIN)
M2
M1
L
ILM output
(1PIN)
CD output
(3PIN)
AUDIO output
(5PIN)
SWD output
(7PIN)
ANT output
(9PIN)
AMP output
(11PIN)
*Usage condition: Use under typical value.
No.A1972-9/13
LV5695P
+
C4 + C3
C2 + C1
CTRL2
C6 + C5
C8 + C7
AUDIO
CD
ILM
CTRL3
IKVDD
VCC1
14
13
C10
+
C9
CTRL1
12
11
VCC
10
9
VDD
8
7
AMP
(NC)
CTRL3
CTRL2
6
5
ANT
4
3
SWD
2
1
AUDIO
CD
ILM
GND
CTRL1
Example of applied circuit
C11 C16 +
C12 +
D2
D4
D3
D5
15
C14 +
R1
C15
C13
VDD
D1
ANT AMP
SWD
VCC
Peripheral parts list
Name of part
C2, C4, C6, C8, C12
C1, C3, C5, C7, C11
Description
Recommended value
Output stabilization capacitor
10μF or more*
Output stabilization capacitor
0.22μF or more*
Remarks
Electrolytic capacitor
Ceramic capacitor
C14, C16
Power supply bypass capacitor
100μF or more
These capacitors must be placed near
C13, C15
Oscillation prevention capacitor
0.22μF or more
the VCC and GND pins.
C9, C10
AMP/ANT output stabilization capacitor
2.2μF or more
R1
Resistance for protection
D1
Diode for prevention of backflow
D2, D3, D4, D5
10 to 100kΩ
Diode for internal element protection
SANYO SB1003M3
note)The circuit diagram and the values are only tentative which are subject to change.
* : Make sure that the capacitors of the output pins are 10μF or higher and ESR is 10Ω or lower in total and temperature characteristics and accuracy are taken
into consideration. Also the E-cap should have good high frequency characteristics.
Caution for implementing LV5695P to a system board
The package of LV5695P is HZIP15J which has some metal exposures other than connection pins and heatsink as shown in the
diagram below. The electrical potentials of (2) and (3) are the same as those of pin 15 and pin 1, respectively. (2) (=pin 15) is the VCC
pin and (3) (=pin 1) is the ILM (regulator) output pin. When you implement the IC to the set board, make sure that the bolts and the
heatsink are out of touch from (2) and (3). If the metal exposures touch the bolts which has the same electrical potential with GND,
GND short occurs in ILM output and VCC. The exposures of (1) are connected to heatsink which has the same electrical potential with
substrate of the IC chip (GND). Therefore, (1) and GND electrical potential of the set board can connect each other.
· HZIP15J outline
Heat-sink
1 Same potential
2 15PIN
Same potential
1PIN
3 Same potential
Heat-sink
1 Same potential
Heat-sink side
1
Heat-sink
Same potential
:Metal exposure
Heat-sink side
:Metal exposure
<Top view of HZIP15J>
<Side view of HZIP15J>
No.A1972-10/13
LV5695P
· Frame diagram (LV5695P) *In the system power supply other than LV5695P, pin assignment may differ.
Metal exposure 1
Metal exposure 3
Metal exposure 2
Metal exposure 1
LV5695
Metal exposure 1
Metal exposure 1
1PIN
15PIN
No.A1972-11/13
LV5695P
HZIP15J Heat sink attachment
Heat sinks are used to lower the semiconductor device junction temperature by leading the head generated by the device to
the outer environment and dissipating that heat.
a. Unless otherwise specified, for power ICs with tabs and power ICs with attached heat sinks, solder must not be
applied to the heat sink or tabs.
b.
Heat sink attachment
· Use flat-head screws to attach heat sinks.
· Use also washer to protect the package.
· Use tightening torques in the ranges 39-59Ncm(4-6kgcm) .
· If tapping screws are used, do not use screws with a diameter larger
than the holes in the semiconductor device itself.
· Do not make gap, dust, or other contaminants to get between the
semiconductor device and the tab or heat sink.
· Take care a position of via hole .
· Do not allow dirt, dust, or other contaminants to get between the
semiconductor device and the tab or heat sink.
· Verify that there are no press burrs or screw-hole burrs on the heat sink.
· Warping in heat sinks and printed circuit boards must be no more than
0.05 mm between screw holes, for either concave or convex warping.
· Twisting must be limited to under 0.05 mm.
· Heat sink and semiconductor device are mounted in parallel.
Take care of electric or compressed air drivers
· The speed of these torque wrenches should never exceed 700 rpm, and
should typically be about 400 rpm.
Binding head
machine screw
Countersunk head
mashine screw
Heat sink
gap
Via hole
c.
Silicone grease
· Spread the silicone grease evenly when mounting heat sinks.
· Sanyo recommends YG-6260 (Momentive Performance Materials Japan LLC)
d.
Mount
· First mount the heat sink on the semiconductor device, and then mount that assembly on the printed circuit board.
· When attaching a heat sink after mounting a semiconductor device into the printed circuit board, when tightening
up a heat sink with the screw, the mechanical stress which is impossible to the semiconductor device and the pin
doesn't hang.
e.
When mounting the semiconductor device to the heat sink using jigs, etc.,
· Take care not to allow the device to ride onto the jig or positioning dowel.
· Design the jig so that no unreasonable mechanical stress is not applied to the semiconductor device.
f.
Heat sink screw holes
· Be sure that chamfering and shear drop of heat sinks must not be larger than the diameter of screw head used.
· When using nuts, do not make the heat sink hole diameters larger than the diameter of the head of the screws used.
A hole diameter about 15% larger than the diameter of the screw is desirable.
· When tap screws are used, be sure that the diameter of the holes in the heat sink are not too small. A diameter about
15% smaller than the diameter of the screw is desirable.
g.
There is a method to mount the semiconductor device to the heat sink by using a spring band. But this method is not
recommended because of possible displacement due to fluctuation of the spring force with time or vibration.
No.A1972-12/13
LV5695P
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of October, 2011. Specifications and information herein are subject
to change without notice.
PS No.A1972-13/13