STMICROELECTRONICS 74VHC16373

74VHC16373
16-BIT D-TYPE LATCH
WITH 3-STATE OUTPUTS NON INVERTING
■
■
■
■
■
■
■
■
■
■
HIGH SPEED:
tPD = 5.0 ns (TYP.) at VCC = 5V
LOW POWER DISSIPATION:
ICC = 4 µA (MAX.) at TA=25°C
HIGH NOISE IMMUNITY:
VNIH = V NIL = 28% VCC (MIN.)
POWER DOWN PROTECTION ON INPUTS
SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 8 mA (MIN)
BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL
OPERATING VOLTAGE RANGE:
VCC(OPR) = 2V to 5.5V
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 16373
IMPROVED LATCH-UP IMMUNITY
LOW NOISE: VOLP = 0.9V (MAX.)
TSSOP
ORDER CODES
PACKAGE
TSSOP
TUBE
T &R
74VHC16373TTR
PIN CONNECTION
DESCRIPTION
The 74VHC16373 is an advanced high-speed
CMOS 16 BIT D-TYPE LATCH with 3 STATE
OUTPUTS NON INVERTING fabricated with
sub-micron silicon gate and double-layer metal
wiring C2MOS technology.
These 16 bit D-TYPE latches are byte controlled
by two latch enable inputs (nLE) and two output
enable inputs(nOE).
While the nLE input is held at a high level, the nQ
outputs will follow the data (D) inputs.
When the nLE is taken LOW, the nQ outputs will
be latched at the logic level of D data inputs.
When the (nOE) input is low, the nQ outputs will
be in a normal logic state (high or low logic level);
when nOE is at high level ,the outputs will be in a
high impedance state.
Power down protection is provided on all inputs
and 0 to 7V can be accepted on inputs with no
regard to the supply voltage. This device can be
used to interface 5V to 3V.
All inputs and outputs are equipped with protection circuits against static discharge, giving them
2KV ESD immunity and transient excess voltage.
July 2001
1/10
74VHC16373
INPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
PIN No
SYMBOL
1
1OE
IEC LOGIC SYMBOLS
NAME AND FUNCTION
3 State Output Enable
Input (Active LOW)
1Q0 to 1Q7 3-State Outputs
2, 3, 5, 6, 8, 9,
11, 12
13, 14, 16, 17, 2Q0 to 2Q7 3-State Outputs
19, 20, 22, 23
24
2OE
3 State Output Enable
Input (Active LOW)
25
2LE
36, 35, 33, 32, 2D0 to 2D7
30, 29, 27, 26
47, 46, 44, 43, 1D0 to 1D7
41, 40, 38, 37
48
1LE
4, 10, 15, 21,
GND
28, 34, 39, 45
7, 18, 31, 42
VCC
Latch Enable Input
Data Inputs
Data Inputs
Latch Enable Input
Ground (0V)
Positive Supply Voltage
TRUTH TABLE
INPUTS
OUTPUT
OE
LE
D
Q
H
L
L
L
X
L
H
H
X
X
L
H
Z
NO CHANGE *
L
H
X : Don‘t Care
Z : High Impedance
* : Q outputs are latched at the time when the LE input is taken low
logic level.
2/10
74VHC16373
LOGIC DIAGRAM
This logic diagram has not to be used to estimate propagation delays
ABSOLUTE MAXIMUM RATINGS
Symbol
V CC
Parameter
Supply Voltage
VI
DC Input Voltage
VO
DC Output Voltage
IIK
DC Input Diode Current
IOK
DC Output Diode Current
IO
DC Output Current
ICC or IGND DC VCC or Ground Current
Storage Temperature
Tstg
TL
Lead Temperature (10 sec)
Value
Unit
-0.5 to +7.0
V
-0.5 to +7.0
V
-0.5 to VCC + 0.5
- 20
V
mA
± 20
mA
± 25
mA
± 75
mA
-65 to +150
°C
300
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
RECOMMENDED OPERATING CONDITIONS
Symbol
V CC
Parameter
Supply Voltage
Value
Unit
2 to 5.5
V
VI
Input Voltage
0 to 5.5
V
VO
Output Voltage
0 to VCC
V
Top
Operating Temperature
-55 to 125
°C
dt/dv
Input Rise and Fall Time (note 1) (VCC = 3.3 ± 0.3V)
(V CC = 5.0 ± 0.5V)
0 to 100
0 to 20
ns/V
1) VIN from 30% to 70% of VCC
3/10
74VHC16373
DC SPECIFICATIONS
Test Condition
Symbol
VIH
V IL
VOH
VOL
I OZ
II
ICC
4/10
Parameter
High Level Input
Voltage
Low Level Input
Voltage
High Level Output
Voltage
Low Level Output
Voltage
High Impedance
Output Leakage
Current
Input Leakage
Current
Quiescent Supply
Current
Value
TA = 25°C
VCC
(V)
Min.
2.0
3.0 to
5.5
2.0
3.0 to
5.5
Typ.
Max.
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
1.5
1.5
1.5
0.7VCC
0.7VCC
0.7VCC
Max.
V
0.5
0.5
0.5
0.3VCC
0.3VCC
0.3VCC
2.0
IO=-50 µA
1.9
2.0
1.9
1.9
3.0
IO=-50 µA
2.9
3.0
2.9
2.9
4.5
IO=-50 µA
4.4
4.5
4.4
4.4
3.0
IO=-4 mA
2.58
2.48
2.4
4.5
IO=-8 mA
3.94
2.0
IO=50 µA
0.0
0.1
0.1
0.1
3.8
Unit
V
V
3.7
3.0
IO=50 µA
0.0
0.1
0.1
0.1
4.5
IO=50 µA
0.0
0.1
0.1
0.1
3.0
IO=4 mA
0.36
0.44
0.55
4.5
IO=8 mA
0.36
0.44
0.55
5.5
VI = VIH or VIL
VO = VCC or GND
±0.25
± 2.5
±5
µA
0 to
5.5
VI = 5.5V or GND
± 0.1
±1
±1
µA
5.5
VI = VCC or GND
4
40
40
µA
V
74VHC16373
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns)
Test Condition
Symbol
tPLH
tPHL
Parameter
Propagation Delay
Time
LE to Qn
VCC
(V)
CL
(pF)
3.3 (*)
(*)
(**)
tPZL
tPZH
tPLZ
tPHZ
tw
ts
th
tOSLH
tOSHL
Propagation Delay
Time
Dn to Qn
Output Enable
Time
Output Disable
Time
Pulse Width (LE)
HIGH
TA = 25°C
-55 to 125°C
Max.
Min.
Max.
Min.
Max.
15
5.5
13
1
15
1
15
50
7
14.5
1
16.5
1
16.5
15
3.6
8.5
1
9.5
1
9.5
5.0(**)
50
5
9.5
1
10.5
1
10.5
3.3
(*)
15
5.5
13
1
15
1
15
3.3
(*)
50
7.5
14
1
16
1
16
(**)
5.0
15
4
8.2
1
9.5
1
9.5
5.0(**)
50
5
9.2
1
10.5
1
10.5
3.3 (*)
15
5.2
13
1
15
1
15
(*)
50
7.6
14.9
1
16
1
16
5.0(**)
15
4
9.1
1
10
1
10
(**)
5.0
50
5
10.1
1
11.5
1
11.5
3.3 (*)
50
9
15.5
1
17
1
17
5.0(**)
50
6
10.5
1
11.5
1
11.5
3.3
3.3
Min.
-40 to 85°C
Typ.
5.0
tPLH
tPHL
Value
3.3 (*)
5
5
5
(**)
5.0
5
5
5
3.3 (*)
4
4
4
(**)
4
4
4
Hold Time Dn to LE 3.3 (*)
HIGH or LOW
5.0(**)
1
1
1
1
1
1
Setup Time Dn to
LE HIGH or LOW
Output to Output
Skew time (note 1)
5.0
ns
ns
ns
ns
ns
ns
ns
ns
3.3 (*)
50
1.5
1.5
1.5
(**)
50
1
1
1
5.0
Unit
ns
(*) Voltage range is 3.3V ± 0.3V
(**) Voltage range is 5.0V ± 0.5V
Note 1 : Parameter guaranteed by design. tsoLH = |t pLHm - tpLHn|, tsoHL = |tpHLm - tpHLn|
CAPACITIVE CHARACTERISTICS
Test Condition
Symbol
Parameter
CIN
Input Capacitance
C OUT
Output
Capacitance
Power Dissipation
Capacitance
(note 1)
C PD
TA = 25°C
VCC
(V)
5.0
Value
Min.
fIN = 10MHz
Typ.
Max.
2.5
10
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
10
Unit
Max.
10
pF
4
pF
21
pF
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/n (per Latch)
5/10
74VHC16373
DYNAMIC SWITCHING CHARACTERISTICS
Test Condition
Symbol
VOLP
V OLV
V IHD
VILD
Parameter
Dynamic Low
Voltage Quiet
Output (note 1, 2)
Dynamic High
Voltage Input
(note 1, 3)
Dynamic Low
Voltage Input
(note 1, 3)
TA = 25°C
VCC
(V)
Min.
5.0
5.0
Value
-0.9
C L = 50 pF
5.0
Typ.
Max.
0.6
0.9
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
Unit
Max.
V
-0.6
3.5
V
1.5
V
1) Worst case package.
2) Max number of outputs defined as (n). Data inputs are driven 0V to 5.0V, (n-1) outputs switching and one output at GND.
3) Max number of data inputs (n) switching. (n-1) switching 0V to 5.0V. Inputs under test switching: 5.0V to threshold (VILD), 0V to threshold
(VIHD), f=1MHz.
TEST CIRCUIT
TEST
SWITCH
tPLH, tPHL
Open
tPZL, tPLZ
VCC
tPZH, tPHZ
GND
C L = 15/50 pF or equivalent (includes jig and probe capacitance)
R L = R1 = 1KΩ or equivalent
R T = ZOUT of pulse generator (typically 50Ω)
6/10
74VHC16373
WAVEFORM 1 : LE TO Qn PROPAGATION DELAYS, LE MINIMUM PULSE WIDTH, Dn TO LE SETUP
AND HOLD TIMES (f=1MHz; 50% duty cycle)
WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle)
7/10
74VHC16373
WAVEFORM 3 : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle)
8/10
74VHC16373
TSSOP48 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
A
MIN.
TYP.
1.1
A1
0.05
0.043
0.15
A2
MAX.
0.002
0.006
0.9
0.035
b
0.17
0.27
0.0067
0.011
c
0.09
0.20
0.0035
0.0079
D
12.4
12.6
0.408
0.496
E
7.95
8.25
0.313
0.325
E1
6.0
6.2
0.236
0.244
e
0.5 BSC
0.0197 BSC
K
0°
8°
0°
8°
L
0.50
0.75
0.020
0.030
A
A2
A1
b
K
e
L
E
c
D
E1
PIN 1 IDENTIFICATION
1
7065588A
9/10
74VHC16373
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringe ment of patents or other righ ts of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this pub lication are subject to change without notice. Thi s pub lication supersedes and replaces all information
previously supplied. STMicroelectronics prod ucts are not authori zed for use as critical components in life suppo rt devices or
systems without express written approval of STMicroelectronics.
 The ST logo is a registered trademark of STMicroelectronics
 2001 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Swit zerland - United Kingdom
 http://w ww.st.com
10/10