ITF F9533

SAW Bandpass Filter F9533
Features
RF bandpass filter for RF-ID System
Usable bandwidth 2 MHz (952.0 MHz ~ 954.0 MHz)
single-ended operation
Ceramic Surface Mounted Device Package ( 3.8 mm × 3.8 mm )
RoHS Compliant
1.00±0.15
1.90±0.15
0.44
3.80±0.15
0.64±0.05
Package Dimensions
6
1
0.44
ITF
9533
8H1
3
5
5
2
4
4
3
1.27±0.05
2
6
1.40±0.15
3.80±0.15
1
Dimensions shown are nominal in millimeters
Pin Configurations
Body : Al2O3 Ceramic
Lid : Kovar, Ni Plated
Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um
Ni Plating
2
Input
5
Output
1, 3, 4, 6
Case ground
Maximum Ratings
Parameters
Unit
Minimum
Typical
Maximum
Operating Temperature Range
°C
-30
25
85
Storage Temperature Range
°C
-40
-
85
Power Handling Capability
dBm
-
-
20
Electrostatics Sensitive Device (ESD)
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
F9533
Rev. Date
2008-08-07
Rev.
NR8006-AS01
1/7
SAW Bandpass Filter F9533
Specifications
Minimum
Typical
Maximum
Unit
Center Frequency ( Fc )
-
953.0
-
MHz
Insertion Loss (In Fc ±1.0 MHz)
-
4.5
5.5
dB
Amplitude Ripple (In Fc ±1.0 MHz)
-
1.0
2.0
dB
VSWR (In Fc ±1.0 MHz)
-
2.0
3.0
Relative Attenuation
830.0 MHz ~
840.0 MHz
30
35
-
940.0 MHz ~
945.0 MHz
20
25
-
945.0 MHz ~
948.0 MHz
15
20
-
948.0 MHz ~
950.0 MHz
12
16
-
956.0 MHz ~
958.0 MHz
25
30
-
Input/Output Impedance
dB
50
Ohm
Notes :
1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and
full 2 port calibration.
2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing
tolerances
3) All attenuation measurements are measured relative to insertion loss
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
F9533
Rev. Date
2008-08-07
Rev.
NR8006-AS01
2/7
SAW Bandpass Filter F9533
Matching Schematic
( Actual matching values may vary due to PCB layout and parasitics )
L2
Input
50Ω
L3
L1
Output
50Ω
L4
L1 = 3.9nH,
L2 = L3 =4.7nH,
L4 = 3.3nH
Marking Configuration
1)
ITF2)
95333)
8H14)
1) Pad Number 1 Index
2) Manufacturer name
3) Marking Number
4) Lot Number
* Ink or Laser Marking available
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
F9533
Rev. Date
2008-08-07
Rev.
NR8006-AS01
3/7
SAW Bandpass Filter F9533
Typical Performance ( at 25℃
℃)
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
F9533
Rev. Date
2008-08-07
Rev.
NR8006-AS01
4/7
SAW Bandpass Filter F9533
Input / Output VSWR Charts
Input / Output Smith Charts
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
F9533
Rev. Date
2008-08-07
Rev.
NR8006-AS01
5/7
SAW Bandpass Filter F9533
Packing Specification
1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel )
2. Taping Structure : The tape shall be wound around the reel in the direction shown below.
TOP COVER TAPE
REEL
CARRIER TAPE
Tape Specification
1. Leader part and vacant position specification
Vacant
150mm min.
Component
contained
Vacant
150mm min.
Leader part
250mm min.
END
START
Tape Running Direction
2. Tensile strength of carrier tape
4.4N/mm width
Direction of pull
Top cover tape
3. Top cover tape adhesion
0~15 degree
1) pull off angle : 0~15°
2) speed : 300mm/min
3) force : 20~70g
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Carrier tape
Part No.
F9533
Rev. Date
2008-08-07
Rev.
NR8006-AS01
6/7
SAW Bandpass Filter F9533
Carrier Tape Dimensions [unit : mm]
A
3.40 ± 0.1
B
3.40 ± 0.1
C
7.25 ± 0.1
D
1.70 ± 0.1
E
12.00 ± 0.1
F
8.00 ± 0.1
Part Direction
Tape Running Direction
Reel Dimensions [unit : mm]
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
F9533
Rev. Date
2008-08-07
Rev.
NR8006-AS01
7/7