LINER LT6205HS5PBF

LT6205/LT6206/LT6207
Single/Dual/Quad
Single Supply 3V,
100MHz Video Op Amps
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
450V/μs Slew Rate
100MHz Gain Bandwidth Product
Wide Supply Range 2.7V to 12.6V
Output Swings Rail-to-Rail
Input Common Mode Range Includes Ground
High Output Drive: 50mA
Channel Separation: 90dB at 10MHz
Specified on 3V, 5V and ±5V Supplies
Input Offset Voltage: 1mV
Low Power Dissipation: 20mW per Amplifier on
Single 5V
Operating Temperature Range: –40°C to 125°C
Low Profile (1mm) SOT-23 (ThinSOT™) Package
n
n
n
n
These amplifiers maintain their performance for supplies
from 2.7V to 12.6V and are specified at 3V, 5V and ±5V.
The inputs can be driven beyond the supplies without
damage or phase reversal of the output. Isolation between
channels is high, over 90dB at 10MHz.
The LT6205 is available in the 5-pin SOT-23, and the LT6206
is available in an 8-lead MSOP package with standard op
amp pinouts. For compact layouts the quad LT6207 is
available in the 16-pin SSOP package. These devices are
specified over the commercial, industrial and automotive
temperature ranges.
APPLICATIONS
n
The LT®6205/LT6206/LT6207 are low cost single/dual/
quad voltage feedback amplifiers that feature 100MHz
gain-bandwidth product, 450V/μs slew rate and 50mA
output current. These amplifiers have an input range that
includes ground and an output that swings within 60mV
of either supply rail, making them well suited for single
supply operation.
Video Line Driver
Automotive Displays
RGB Amplifiers
Coaxial Cable Drivers
Low Voltage High Speed Signal Processing
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property
of their respective owners.
TYPICAL APPLICATION
Baseband Video Splitter/Cable Driver
3.3V
499Ω
Output Step Response
1μF
VOUT
75Ω
499Ω
VOUT1
8
LT6206
VIN
2
–
3
+
0V
75Ω
1
VIN
0V
75Ω
5
+
7
6
499Ω
20ns/DIV
620567 TA01b
VOUT2
–
75Ω
4
499Ω
VS = 3.3V
VIN = 0.1V TO 1.1V
f = 10MHz
75Ω
F3dB z 50MHz
IS b 25mA
620567 TA01a
620567fc
1
LT6205/LT6206/LT6207
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Total Supply Voltage (V + to V–) ..............................12.6V
Input Current .......................................................±10mA
Input Voltage Range (Note 2)....................................±VS
Output Short-Circuit Duration (Note 3) ........... Indefinite
Pin Current While Exceeding Supplies (Note 9) ...±25mA
Operating Temperature Range (Note 4)
LT6205C/LT6206C/LT6207C,
LT6205I/LT6206I/LT6207I .................... –40°C to 85°C
LT6205H ........................................... –40°C to 125°C
Specified Temperature Range (Note 4)
LT6205C/LT6206C/LT6207C ..................... 0°C to 70°C
LT6205I/LT6206I/LT6207I .................... –40°C to 85°C
LT6205H ........................................... –40°C to 125°C
Storage Temperature Range .................. –65°C to 150°C
Maximum Junction Temperature .......................... 150°C
Lead Temperature (Soldering, 10 sec) ................. 300°C
PIN CONFIGURATION
TOP VIEW
OUT A 1
TOP VIEW
TOP VIEW
5 V+
OUT 1
OUT A
–IN A
+IN A
V–
V– 2
+
–
+IN 3
4 –IN
1
2
3
4
–
+
–
+
8
7
6
5
V+
OUT B
–IN B
+IN B
MS8 PACKAGE
8-LEAD PLASTIC MSOP
S5 PACKAGE
5-LEAD PLASTIC TSOT-23
TJMAX = 150°C, θJA = 250°C/W
TJMAX = 150°C, θJA = 250°C/W
16 OUT D
–IN A 2
–
+IN A 3
+
A
D
–
15 –IN D
+
14 +IN D
V+ 4
13 V–
+IN B 5
+
–IN B 6
–
B
C
+
12 +IN C
–
11 –IN C
OUT B 7
NC 8
10 OUT C
9
NC
GN PACKAGE
16-LEAD NARROW PLASTIC SSOP
TJMAX = 150°C, θJA = 135°C/W
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LT6205CS5#PBF
LT6205CS5#TRPBF
LTAEM
5-Lead Plastic TSOT-23
0°C to 70°C
LT6205IS5#PBF
LT6205IS5#TRPBF
LTAEM
5-Lead Plastic TSOT-23
–40°C to 85°C
LT6205HS5#PBF
LT6205HS5#TRPBF
LTAEM
5-Lead Plastic TSOT-23
–40°C to 125°C
LT6206CMS8#PBF
LT6206CMS8#TRPBF
LTH3
8-Lead Plastic MSOP
0°C to 70°C
LT6206IMS8#PBF
LT6206IMS8#TRPBF
LTH4
8-Lead Plastic MSOP
–40°C to 85°C
LT6207CGN#PBF
LT6207CGN#TRPBF
6207
16-Lead Narrow Plastic SSOP
0°C to 70°C
LT6207IGN#PBF
LT6207IGN#TRPBF
6207I
16-Lead Narrow Plastic SSOP
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
620567fc
2
LT6205/LT6206/LT6207
ELECTRICAL CHARACTERISTICS
The l denotes specifications which apply over the specified temperature
range, otherwise specifications are at TA = 25°C. VS = 3V, 0V; VS = 5V, 0V; VCM = VOUT = 1V, unless otherwise noted.
LT6205C/LT6206C/LT6207C
LT6205I/LT6206I/LT6207I
SYMBOL
PARAMETER
VOS
Input Offset Voltage
IB
IOS
MIN
CONDITIONS
l
TYP
MAX
1
3.5
5
mV
mV
1
3
4
mV
mV
UNITS
Input Offset Voltage Match
(Channel-to-Channel) (Note 5)
l
Input Offset Voltage Drift (Note 6)
l
7
15
μV/°C
Input Bias Current
l
10
30
μA
Input Offset Current
l
0.6
3
μA
Input Noise Voltage
0.1Hz to 10Hz
2
μVP-P
en
Input Noise Voltage Density
f = 10kHz
9
nV/√Hz
in
Input Noise Current Density
f = 10kHz
4
pA/√Hz
1
MΩ
Input Resistance
VCM
= 0V to V+ – 2V
Input Capacitance
CMRR
Common Mode Rejection Ratio
VCM = 0V to V+ – 2V
Input Voltage Range
l
78
l
0
67
2
pF
90
dB
V+ – 2
V
Power Supply Rejection Ratio
VS = 3V to 12V
VCM = VOUT = 0.5V
l
Minimum Supply Voltage
VCM = 0.5V
l
A VOL
Large-Signal Voltage Gain
VS = 5V, VO = 0.5V to 4.5V, RL = 1k
VS = 5V, VO = 1V to 3V, RL = 150Ω
VS = 3V, VO = 0.5V to 2.5V, RL = 1k
l
l
l
VOL
Output Voltage Swing Low (Note 7) No Load, Input Overdrive = 30mV
ISINK = 5mA
VS = 5V, ISINK = 25mA
VS = 3V, ISINK = 15mA
l
l
l
l
10
75
300
200
25
150
500
350
mV
mV
mV
mV
VOH
Output Voltage Swing High (Note 7) No Load, Input Overdrive = 30mV
ISOURCE = 5mA
VS = 5V, ISOURCE = 25mA
VS = 3V, ISOURCE = 15mA
l
l
l
l
60
150
650
300
100
250
1200
500
mV
mV
mV
mV
ISC
Short-Circuit Current
PSRR
VS = 5V, Output Shorted to GND
VS = 3V, Output Shorted to GND
IS
Supply Current per Amplifier
GBW
Gain Bandwidth Product
f = 2MHz
SR
Slew Rate
75
dB
2.7
30
5
20
100
20
60
V
V/mV
V/mV
V/mV
l
35
20
60
mA
mA
l
30
20
50
mA
mA
3.75
l
l
65
5
5.75
mA
mA
100
MHz
VS = 5V, A V = 2, RF = RG = 1k
VO = 1V to 4V, Measured from 1.5V to 3.5V
450
V/μs
Channel Separation
f = 10MHz
90
dB
FPBW
Full Power Bandwidth
VOUT = 2VP-P (Note 8)
71
MHz
ts
Settling Time to 3%
Settling Time to 1%
VS = 5V, ΔVOUT = 2V, AV = –1, RL = 150Ω
15
25
ns
ns
Differential Gain
Differential Phase
VS = 5V, A V = 2, RL = 150Ω, Output Black Level = 1V
VS = 5V, A V = 2, RL = 150Ω, Output Black Level = 1V
0.05
0.08
%
Deg
620567fc
3
LT6205/LT6206/LT6207
ELECTRICAL CHARACTERISTICS
The l denotes specifications which apply over the specified temperature
range, otherwise specifications are at TA = 25°C. VS = ±5V; VCM = VOUT = 0V, unless otherwise noted.
LT6205C/LT6206C/LT6207C
LT6205I/LT6206I/LT6207I
SYMBOL
PARAMETER
VOS
Input Offset Voltage
MIN
CONDITIONS
l
TYP
MAX
1
4.5
6
mV
mV
1
3
4
mV
mV
UNITS
Input Offset Voltage Match
(Channel-to-Channel) (Note 5)
l
Input Offset Voltage Drift (Note 6)
l
10
18
μV/°C
IB
Input Bias Current
l
18
30
μA
IOS
Input Offset Current
l
0.6
3
μA
Input Noise Voltage
0.1Hz to 10Hz
2
en
Input Noise Voltage Density
f = 10kHz
9
nV/√Hz
in
Input Noise Current Density
f = 10kHz
4
pA/√Hz
Input Resistance
VCM = –5V to 3V
1
MΩ
2
pF
90
dB
Input Capacitance
CMRR
Common Mode Rejection Ratio
VCM = –5V to 3V
Input Voltage Range
l
78
l
–5
μVP-P
3
V
PSRR
Power Supply Rejection Ratio
VS = ±2V to ±6V
l
67
75
dB
AVOL
Large-Signal Voltage Gain
VO = –4V to 4V, RL = 1k
l
50
133
V/mV
V/mV
VO = –3V to 3V, RL = 150Ω
l
7.5
20
Output Voltage Swing
No Load, Input Overdrive = 30mV
IOUT = ±5mA
IOUT = ±25mA
l
l
l
±4.88
±4.75
±3.8
±4.92
±4.85
±4.35
ISC
Short-Circuit Current
Short to Ground
l
±40
±30
±60
IS
Supply Current per Amplifier
GBW
Gain Bandwidth Product
f = 2MHz
SR
Slew Rate
A V = –1, RL = 1k
VO = –4V to 4V, Measured from –3V to 3V
Channel Separation
f = 10MHz
FPBW
Full Power Bandwidth
VOUT = 8VP-P (Note 8)
ts
Settling Time to 3%
Settling Time to 1%
ΔVOUT = 2V, AV = –1, RL = 150Ω
Differential Gain
Differential Phase
A V = 2, RL = 150Ω, Output Black Level = 1V
A V = 2, RL = 150Ω, Output Black Level = 1V
4
l
l
V
V
V
mA
mA
5.6
6.5
mA
mA
65
100
MHz
350
600
V/μs
90
dB
24
MHz
15
25
ns
ns
0.05
0.08
%
Deg
14
The l denotes specifications which apply over the full specified temperature range, –40°C ≤ TA ≤ 125°C, otherwise specifications are
at TA = 25°C. VS = 3V, 0V; VS = 5V, 0V; VCM = VOUT = 1V, unless otherwise noted.
LT6205H
SYMBOL
PARAMETER
VOS
Input Offset Voltage
IB
CONDITIONS
MIN
l
UNITS
TYP
MAX
1
3.5
6
mV
mV
Input Offset Voltage Drift (Note 6)
l
20
μV/°C
Input Bias Current
l
45
μA
620567fc
4
LT6205/LT6206/LT6207
ELECTRICAL CHARACTERISTICS
The l denotes specifications which apply over the full specified temperature
range, –40°C ≤ TA ≤ 125°C, otherwise specifications are at TA = 25°C. VS = 3V, 0V; VS = 5V, 0V; VCM = VOUT = 1V, unless otherwise noted.
LT6205H
SYMBOL
IOS
PARAMETER
CONDITIONS
MIN
TYP
l
Input Offset Current
MAX
5
UNITS
μA
Input Noise Voltage
0.1Hz to 10Hz
2
μVP-P
en
Input Noise Voltage Density
f = 10kHz
9
nV/√Hz
in
Input Noise Current Density
f = 10kHz
4
pA/√Hz
1
MΩ
Input Resistance
VCM
= 0V to V+ – 2V
Input Capacitance
CMRR
Common Mode Rejection Ratio
2
VCM = 0V to V+ – 2V
Input Voltage Range
l
72
l
0
62
pF
dB
V+ – 2
V
Power Supply Rejection Ratio
VS = 3V to 12V
VCM = VOUT = 0.5V
l
Minimum Supply Voltage
VCM = 0.5V
l
AVOL
Large-Signal Voltage Gain
VS = 5V, V0 = 0.5V to 4.5V, RL = 1k
VS = 5V, V0 = 1V to 3V, RL = 150Ω
VS = 3V, V0 = 0.5V to 2.5V, RL = 1k
l
l
l
VOL
Output Voltage Swing Low (Note 7) No Load, Input Overdrive = 30mV
ISINK = 5mA
VS = 5V, ISINK = 25mA
VS = 3V, ISINK = 15mA
l
l
l
l
40
200
600
400
mV
mV
mV
mV
VOH
Output Voltage Swing High (Note 7) No Load, Input Overdrive = 30mV
ISOURCE = 5mA
VS = 5V, ISOURCE = 25mA
VS = 3V, ISOURCE = 15mA
l
l
l
l
125
300
1400
600
mV
mV
mV
mV
ISC
Short-Circuit Current
PSRR
VS = 5V, Output Shorted to GND
VS = 3V, Output Shorted to GND
dB
2.7
25
3.5
15
V
V/mV
V/mV
V/mV
l
35
20
60
mA
mA
l
30
15
50
mA
mA
IS
Supply Current per Amplifier
GBW
Gain Bandwidth Product
f = 2MHz
SR
Slew Rate
VS = 5V, AV = 2, RF = RG = 1k
VO = 1V to 4V, Measured from 1.5V to 3.5V
450
V/μs
Channel Separation
f = 10MHz
90
dB
FPBW
Full Power Bandwidth
VOUT = 2VP-P (Note 8)
71
MHz
ts
Settling Time to 3%
Settling Time to 1%
VS = 5V, ΔVOUT = 2V, A V = –1, RL = 150Ω
15
25
ns
ns
Differential Gain
Differential Phase
VS = 5V, A V = 2, RL = 150Ω, Output Black Level = 1V
VS = 5V, A V = 2, RL = 150Ω, Output Black Level = 1V
0.05
0.08
%
Deg
3.75
l
l
5
6.5
50
mA
mA
MHz
The l denotes specifications which apply over the full specified temperature range, –40°C ≤ TA ≤ 125°C, otherwise specifications are
at TA = 25°C. VS = ±5V; VCM = VOUT = 0V, unless otherwise noted.
LT6205H
SYMBOL
PARAMETER
VOS
Input Offset Voltage
Input Offset Voltage Drift (Note 6)
CONDITIONS
MIN
l
l
UNITS
TYP
MAX
1.3
4.5
7
mV
mV
25
μV/°C
620567fc
5
LT6205/LT6206/LT6207
ELECTRICAL CHARACTERISTICS
The l denotes specifications which apply over the full specified
temperature range, –40°C ≤ TA ≤ 125°C, otherwise specifications are at TA = 25°C. VS = ±5V; VCM = VOUT = 0V, unless otherwise noted.
LT6205H
SYMBOL
PARAMETER
CONDITIONS
IB
Input Bias Current
l
50
μA
IOS
Input Offset Current
l
5
μA
MIN
TYP
MAX
UNITS
Input Noise Voltage
0.1Hz to 10Hz
2
μVP-P
en
Input Noise Voltage Density
f = 10kHz
9
nV/√Hz
in
Input Noise Current Density
f = 10kHz
4
pA/√Hz
Input Resistance
VCM = –5V to 3V
1
MΩ
2
pF
Input Capacitance
CMRR
Common Mode Rejection Ratio
l
72
l
–5
VS = ±2V to ±6V
l
62
VCM = –5V to 3V
Input Voltage Range
PSRR
Power Supply Rejection Ratio
A VOL
Large-Signal Voltage Gain
dB
3
V
dB
VO = –4V to 4V, RL = 1k
l
40
V/mV
VO = –3V to 3V, RL = 150Ω
l
5
V/mV
Output Voltage Swing
No Load, Input Overdrive = 30mV
IOUT = ±5mA
IOUT = ±25mA
l
l
l
±4.85
±4.65
±3.5
ISC
Short-Circuit Current
Short to Ground
l
±40
±20
IS
Supply Current per Amplifier
GBW
Gain Bandwidth Product
f = 2MHz
SR
Slew Rate
A V = –1, RL = 1k
VO = –4V to 4V, Measured from –3V to 3V
Channel Separation
f = 10MHz
FPBW
Full Power Bandwidth
VOUT = 8VP-P (Note 8)
ts
Settling Time to 3%
Settling Time to 1%
ΔVOUT = 2V, AV = –1, RL = 150Ω
Differential Gain
Differential Phase
A V = 2, RL = 150Ω, Output Black Level = 1V
A V = 2, RL = 150Ω, Output Black Level = 1V
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The inputs are protected by back-to-back diodes. If the differential
input voltage exceeds 1.4V, the input current should be limited to less than
10mA.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum. This depends on the power supply voltage and
how many amplifiers are shorted.
Note 4: The LT6205C/LT6206C/LT6207C are guaranteed to meet specified
performance from 0°C to 70°C and are designed, characterized and
expected to meet specified performance from –40°C to 85°C but are not
tested or QA sampled at these temperatures. The LT6205I/LT6206I/LT6207I
are guaranteed to meet specified performance from –40°C to 85°C. The
LT6205H is guaranteed to meet specified performance from –40°C to 125°C.
±60
4
l
l
V
V
V
50
mA
mA
5.6
7.5
mA
mA
MHz
350
600
V/μs
90
dB
14
24
MHz
15
25
ns
ns
0.05
0.08
%
Deg
Note 5: Matching parameters are the difference between the two amplifiers
A and D and between B and C of the LT6207; between the two amplifiers of
the LT6206.
Note 6: This parameter is not 100% tested.
Note 7: Output voltage swings are measured between the output and
power supply rails.
Note 8: Full power bandwidth is calculated from the slew rate
measurement: FPBW = SR/2πVPEAK.
Note 9: There are reverse biased ESD diodes on all inputs and outputs.
If these pins are forced beyond either supply, unlimited current will flow
through these diodes. If the current is transient in nature and limited to
less than 25mA, no damage to the device will occur.
620567fc
6
LT6205/LT6206/LT6207
TYPICAL PERFORMANCE CHARACTERISTICS
Supply Current per Amplifier
vs Supply Voltage
VOS Distribution
30
25
20
15
10
5
0
100
TA = 125°C
4
TA = 25°C
3
TA = –55°C
2
1
0
–3
–2
–1
0
1
2
INPUT OFFSET VOLTAGE (mV)
3
0
1
2
TA = 25°C
200
TA =125°C
0
–4
–5
–6
TA = 125°C
–7
–8
TA = 25°C
–9
–10
5
0
TA = 125°C
1
TA = 25°C
0.01
0.01
TA = –55°C
0.1
1
10
LOAD CURRENT (mA)
100
620567 G07
OUTPUT SATURATION VOLTAGE (V)
OUTPUT SATURATION VOLTAGE (V)
10
0.1
–6
–7
–8
–9
–10
1
2
3
4
INPUT COMMON MODE VOLTAGE (V)
–12
–50
5
–25
0
25
50
75
TEMPERATURE (°C)
100
VS = 5V, 0V
VOD = 30mV
Short-Circuit Current
vs Temperature
75
TA = 125°C
1
TA = 25°C
0.1
0.01
0.01
125
620567 G06
Output Saturation Voltage
vs Load Current (Output High)
VS = 5V, 0V
VOD = 30mV
VS = 5V, 0V
VCM = 1V
620567 G05
Output Saturation Voltage
vs Load Current (Output Low)
5.0
–11
TA = –55°C
620567 G04
10
2.5 3.0 3.5 4.0 4.5
TOTAL SUPPLY VOLTAGE (V)
Input Bias Current vs Temperature
–4
–12
1
2
3
4
INPUT COMMON MODE VOLTAGE (V)
2.0
620567 G03
–5
–11
TA = –55°C
0
–500
VS = 5V, 0V
–3
400
TA = 25°C
–400
INPUT BIAS CURRENT (μA)
VS = 5V, 0V
INPUT BIAS CURRENT (μA)
OFFSET VOLTAGE CHANGE (μV)
–2
600
TA =125°C
–300
Input Bias Current vs Input
Common Mode Voltage
800
TA = –55°C
–200
620567 G02
Change in Offset Voltage vs Input
Common Mode Voltage
1000
–100
–600
1.5
3 4 5 6 7 8 9 10 11 12
TOTAL SUPPLY VOLTAGE (V)
620567 G01
0
OUTPUT SHORT-CIRCUIT CURRENT (mA)
PERCENT OF UNITS (%)
SUPPLY CURRENT PER AMPLIFIER (mA)
VS = 5V, 0V
VCM = 1V
35
Minimum Supply Voltage
5
CHANGE IN INPUT OFFSET VOLTAGE (μV)
40
TA = –55°C
0.1
1
10
LOAD CURRENT (mA)
100
620567 G08
70
SINKING
65
VS = 5V, 0V
VCM = 1V
SOURCING
60
SINKING
55
SOURCING
50
45
VS = 3V, 0V
VCM = 1V
40
35
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
620567 G09
620567fc
7
LT6205/LT6206/LT6207
TYPICAL PERFORMANCE CHARACTERISTICS
Short-Circuit Current
vs Temperature
Open-Loop Gain
Open-Loop Gain
500
VS = p5V
VS = 5V, 0V
VCM = 1V
TA = 25°C
400
80
INPUT VOLTAGE (μV)
70
SOURCING
60
50
40
3O
–50
100
RL = 1k
–100
RL = 150Ω
–200
0
25
50
75
TEMPERATURE (°C)
100
80
VS = 5V, 0V
60
40
20
0
25
16
20
15
10
5
1k
10k
FREQUENCY (Hz)
10
8
6
4
2
1k
10k
FREQUENCY (Hz)
100k
Gain Bandwidth and Phase
Margin vs Supply Voltage
70
140
PHASE
60
50
100
30
20
40
10
0
–10
60
20
VS = 3V, 0V
TA = 25°C
RL = 1k
CL = 5pF
–20
100k
0
PHASE (DEG)
80
VS = p5V
45
PHASE MARGIN
40
110
35
GAIN BANDWIDTH
105
PHASE MARGIN (DEG)
VS = 3V, 0V
50
TA = 25°C
RF = RG = 1k
CL = 5pF
120
40
GAIN (dB)
12
620567 G15
Gain and Phase vs Frequency
NOISE VOLTAGE (1μV/DIV)
VS = 5V, 0V
VCM = 1V
TA = 25°C
620567 G14
0.1Hz to 10Hz Noise Voltage
620567 G16
14
0
100
100k
620567 G13
5
Input Noise Current Density
vs Frequency
VS = 5V, 0V
VCM = 1V
TA = 25°C
0
100
10 20 30 40 50 60 70 80 90 100
TIME AFTER POWER-UP (s)
4
620567 G12
INPUT NOISE CURRENT DENSITY (pA/•Hz)
30
VS = ±5V
TIME (2 SEC/DIV)
3
620567 G11
INPUT NOISE VOLTAGE DENSITY (nV/•Hz)
CHANGE IN OFFSET VOLTAGE (μV)
–5 –4 –3 –2 –1 0 1 2
OUTPUT VOLTAGE (V)
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
OUTPUT VOLTAGE (V)
Input Noise Voltage Density
vs Frequency
VS = 5V, 0V
VCM = 1V
TA = 25°C
RL = 150Ω
–200
–500
0
TA = 25°C
100
–100
–400
125
RL = 1k
0
–300
Warm Up Drift vs Time (LT6206)
120
100
–400
–500
–25
200
–300
620567 G10
0
300
200
0
VS = p5V
TA = 25°C
400
INPUT VOLTAGE ( μV)
300
SINKING
500
GAIN BANDWIDTH (MHz)
OUTPUT SHORT-CIRCUIT CURRENT (mA)
90
100
GAIN
1M
VS = p5V
10M
FREQUENCY (Hz)
100M
-20
-40
500M
620567 G17
95
0
2
4
6
8
10
TOTAL SUPPLY VOLTAGE (V)
12
620567 G18
620567fc
8
LT6205/LT6206/LT6207
TYPICAL PERFORMANCE CHARACTERISTICS
Gain Bandwidth and Phase
Margin vs Temperature
50
700
45
35
VS = 3V, 0V
VS = p5V
120
110
80
–50
–25
0
25
50
75
TEMPERATURE (°C)
FALLING VS = p5V
550
RISING VS = 5V, 0V
500
FALLING VS = 5V, 0V
400
100
350
–50
125
GAIN (dB)
0
VS = 3V
VCM = 1V
OUTPUT IMPEDANCE (Ω)
VS = p5V
VCM = 0V
3
–9
0
25
50
75
TEMPERATURE (°C)
100
125
1M
10M
FREQUENCY (Hz)
100M
AV = 10
AV = 1
AV = 2
10
1
0.1
100k
500M
1M
10M
FREQUENCY (Hz)
70
60
40
30
20
10
30
40
35
VS = 5V, 0V
AV = 1
TA = 25°C
0
10k
90
80
70
1M
10M
FREQUENCY (Hz)
100M
1G
620567 G25
100M
RS = 10Ω, RL = d
25
20
RS = 20Ω, RL = d
15
60
10
50
5
40
100k
1M
10M
FREQUENCY (Hz)
30
20
10
100k
Series Output Resistor
vs Capacitive Load
OVERSHOOT (%)
40
–PSRR
620567 G24
VS = p5V
LT6206 CH A-B
110
LT6207 CH A-D, CH B-C
T = 25°C
100 A
80
50
+PSRR
50
0
10k
500M
120
VOLTAGE GAIN (dB)
COMMON MODE REJECTION RATIO (dB)
100M
VS = 5V, 0V
TA = 25°C
80
620567 G23
VS = p5V
TA = 25°C
60
5
620567 G21
Channel Separation vs Frequency
70
4
90
100
Common Mode Rejection Ratio
vs Frequency
90
3
Power Supply Rejection Ratio
vs Frequency
VS = 5V, 0V
TA = 25°C
620567 G22
100
2
GAIN (AV)
–12
–15
100k
FALLING
500
400
–25
POWER SUPPLY REJECTION RATIO (dB)
1000
–6
550
Output Impedance vs Frequency
15
–3
RISING
600
620567 G20
Closed-Loop Gain vs Frequency
6
650
450
620567 G19
TA = 25°C
12 CL = 5pF
A = +1
9 V
VS = p5V
VO = –4V to 4V
RL = 1k
TA = 25°C
700
450
GAIN BANDWIDTH
90
RISING VS = p5V
600
VS = 3V, 0V
100
AV = –1
RG = RF = 1k
RL = 1k
650
SLEW RATE (V/μs)
40
PHASE MARGIN
Slew Rate vs Closed-Loop Gain
750
SLEW RATE (V/μs)
VS = p5V
750
PHASE MARGIN (DEG)
GAIN BANDWIDTH (MHz)
RL = 1k
CL = 5pF
Slew Rate vs Temperature
55
RL = RS = 50Ω
0
1M
10M
FREQUENCY (Hz)
100M
620567 G26
10
100
CAPACITIVE LOAD (pF)
1000
620567 G27
620567fc
9
LT6205/LT6206/LT6207
TYPICAL PERFORMANCE CHARACTERISTICS
Series Output Resistor
vs Capacitive Load
VS = 5V, 0V
AV = 2
TA = 25°C
9
RS = 10Ω, RL = d
OVERSHOOT (%)
30
25
20
RS = 20Ω, RL = d
15
10
RL = RS = 50Ω
5
0
100
CAPACITIVE LOAD (pF)
AV = –1
8
6
5
4
3
2
VS = p5V
TA = 25°C
HD2, HD3 < –30dBc
–70
RL = 1k, 2ND
RL = 150Ω, 2ND
RL = 150Ω, 3RD
–80
RL = 1k, 3RD
1
10
FREQUENCY (MHz)
100
–100
0.01
AV = +1
VO = 2VP-P
VS = p5V
–40
RL = 150Ω, 3RD
–50
0.1
1
FREQUENCY (MHz)
–60
RL = 150Ω, 2ND
–70
AV = +2
VO = 2VP-P
VS = p5V
RL = 150Ω, 3RD
–50
RL = 150Ω, 2ND
–60
–70
–80
–90
RL = 1k, 2ND
RL = 1k, 3RD
10
10
Distortion vs Frequency
–90
RL = 1k, 3RD
0.1
1
FREQUENCY (MHz)
620567 G31
–30
–80
–90
RL = 150Ω, 2ND
–100
0.01
DISTORTION (dB)
–40
DISTORTION (dB)
DISTORTION (dB)
AV = +2
VO = 2VP-P
VS = 5V, 0V
–60
RL = 150Ω, 3RD
–70
Distortion vs Frequency
–30
–50
–60
620567 G30
Distortion vs Frequency
–40
RL = 1k, 2ND
–50
–90
620567 G28
–30
AV = +1
VO = 2VP-P
VS = 5V, 0V
–80
0
0.1
1000
–40
AV = 2
7
1
10
–30
DISTORTION (dB)
35
Distortion vs Frequency
10
OUTPUT VOLTAGE SWING (VP-P)
40
Maximum Undistorted Output
Signal vs Frequency
RL = 1k, 2ND
–100
0.01
0.1
1
FREQUENCY (MHz)
620567 G32
10
–100
0.01
0.1
1
FREQUENCY (MHz)
10
620567 G34
620567 G33
Large Signal Response
VS = 5V, 0V
RL = 1k, 3RD
500mV/DIV
500mV/DIV
Small Signal Response
VS = 5V, 0V
2.5V
0V
VS = 5V, 0V
AV = 1
RL = 150Ω
50ns/DIV
620567 G35
VS = 5V, 0V
AV = 1
RL = 150Ω
50ns/DIV
620567 G36
620567fc
10
LT6205/LT6206/LT6207
TYPICAL PERFORMANCE CHARACTERISTICS
620567 G37
50ns/DIV
VS = ±5V
AV = 1
RL = 150Ω
0V
0V
VOUT (2V/DIV
0V
Output-Overdrive Recovery
VIN (1V/DIV
Small Signal Response VS = ±5V
50mV/DIV
1V/DIV
Large Signal Response VS = ±5V
620567 G38
50ns/DIV
VS = ±5V
AV = 1
RL = 150Ω
0V
100ns/DIV
VS = 5V, 0V
AV = 2
620567 G39
APPLICATIONS INFORMATION
V+
I1
I2
R2
I3
R3
Q13
Q9
Q2
V+
Q5
CM
V+
R1
RIN
150Ω
DESD1
Q3
Q10
Q7
Q1
+IN
DESD2
D1
D3
D2
D4
Q4
DESD5
Q6
COMPLEMENTARY
DRIVE
GENERATOR
Q8
OUT
DESD6
V–
Q12
Q11
V–
V+
RIN
150Ω
DESD3
–IN
Q14
I4
R4
R5
V–
DESD4
620567 F01
V–
Figure 1. Simplified Schematic
620567fc
11
LT6205/LT6206/LT6207
APPLICATIONS INFORMATION
Amplifier Characteristics
Figure 1 shows a simplified schematic of the LT6205/
LT6206/LT6207. The input stage consists of transistors
Q1 to Q8 and resistor R1. This topology allows for high
slew rates at low supply voltages. The input common
mode range extends from ground to typically 1.75V from
VCC, and is limited by 2 VBEs plus a saturation voltage of
a current source. There are back-to-back series diodes,
D1 to D4, across the + and – inputs of each amplifier to
limit the differential voltage to ±1.4V. RIN limits the current
through these diodes if the input differential voltage exceeds
±1.4V. The input stage drives the degeneration resistors of
PNP and NPN current mirrors, Q9 to Q12, which convert
the differential signals into a single-ended output. The
complementary drive generator supplies current to the
output transistors that swing from rail-to-rail.
The current generated through R1, divided by the capacitor
CM, determines the slew rate. Note that this current, and
hence the slew rate, are proportional to the magnitude
of the input step. The input step equals the output step
divided by the closed loop gain. The highest slew rates
are therefore obtained in the lowest gain configurations.
The Typical Performance Characteristics curve of Slew
Rate vs Closed-Loop Gain shows the details.
ESD
The LT6205/LT6206/LT6207 have reverse-biased ESD
protection diodes on all inputs and outputs as shown in
Figure 1. If these pins are forced beyond either supply
unlimited current will flow through these diodes. If the
current is transient, and limited to 25mA or less, no damage to the device will occur.
Layout and Passive Components
With a gain bandwidth product of 100MHz and a slew rate
of 450V/μs the LT6205/LT6206/LT6207 require special
attention to board layout and supply bypassing. Use a
ground plane, short lead lengths and RF quality low ESR
supply bypass capacitors. The positive supply pin should
be bypassed with a small capacitor (typically 0.01μF to
0.1μF) within 0.25 inches of the pin. When driving heavy
loads, an additional 4.7μF electrolytic capacitor should be
used. When using split supplies, the same is true for the
negative supply pin. For optimum performance all feedback
components and bypass capacitors should be contained
in a 0.5 inch by 0.5 inch area. This helps ensure minimal
stray capacitances.
The parallel combination of the feedback resistor and gain
setting resistor on the inverting input can combine with
the input capacitance to form a pole which can degrade
stability. In general, use feedback resistors of 1k or less.
Capacitive Load
The LT6205/LT6206/LT6207 are optimized for wide bandwidth video applications. They can drive a capacitive load
of 20pF in a unity-gain configuration. When driving a
larger capacitive load, a resistor of 10Ω to 50Ω should
be connected between the output and the capacitive load
to avoid ringing or oscillation. The feedback should still
be taken from the output pin so that the resistor will
isolate the capacitive load and ensure stability. The Typical Performance Characteristics curves show the output
overshoot when driving a capacitive load with different
series resistors.
Video Signal Characteristics
Composite video is the most commonly used signal in
broadcast grade products and includes luma (or luminance, the intensity information), chroma (the colorimetry
information) and sync (vertical and horizontal raster timing) elements combined into a single signal, NTSC and
PAL being the common formats. Component video for
entertainment systems include separate signal(s) for the
luma and chroma (i.e., Y/C or YPbPr) with sync generally
applied to the luma channel (Y signal). In some instances,
native RGB signals (separate intensity information for each
primary color: red, green, blue) will have sync included as
well. All the signal types that include sync are electrically
similar from a voltage-swing standpoint, though various
timing and bandwidth relationships exist depending on
the applicable standard.
The typical video waveforms that include sync (including full composite) are specified to have nominal 1VP-P
amplitude. The lower 0.3V is reserved for sync tips that
carry timing information, and by being at a lower potential
than all the other information, represents blacker-than620567fc
12
LT6205/LT6206/LT6207
APPLICATIONS INFORMATION
black intensity, thereby causing scan retrace activity to be
invisible on a CRT. The black level of the waveform is at
(or set up very slightly above) the upper limit of the sync
information. Waveform content above the black level is
intensity information, with peak brightness represented
at the maximum signal level. In the case of composite
video, the modulated color subcarrier is superimposed on
the waveform, but the dynamics remain inside the 1VP-P
limit (a notable exception is the chroma ramp used for
differential-gain and differential-phase measurements,
which can reach 1.15VP-P).
DC-Coupled Video Amplifier Considerations
Typically video amplifiers drive cables that are series
terminated (back-terminated) at the source and load-terminated at the destination with resistances equal to the
cable characteristic impedance, Z0 (usually 75Ω). This
configuration forms a 2:1 resistor divider in the cabling
that must be accounted for in the driver amplifier by
delivering 2VP-P output into an effective 2 • Z0 load (e.g.,
150Ω). Driving the cable can require more than 13mA
while the output is approaching the saturation limits of the
amplifier output. The absolute minimum supply is: VMIN =
2 + VOH +VOL. For example, the LT6206 dual operating on
3.3V as shown on the front page of this data sheet, with
exceptionally low VOH ≤ 0.5V and VOL ≤ 0.35V, provides a
design margin of 0.45V. The design margin must be large
enough to include supply variations and DC bias accuracy
for the DC-coupled video input.
Handling AC-Coupled Video Signals
AC-coupled video inputs are intrinsically more difficult to
handle than those with DC-coupling because the average
signal voltage of the video waveform is effected by the
picture content, meaning that the black level at the amplifier
wanders with scene brightness. The wander is measured
as 0.56V for a 1VP-P NTSC waveform changing from black
field to white field and vice-versa, so an additional 1.12V
allowance must be made in the amplifier supply (assuming gain of 2, so VMIN = 3.12 + VOH +VOL). For example,
an LT6205 operating on 5V has a conservative design
margin of 1.03V. The amplifier output (for gain of 2) must
swing +1.47V to –1.65V around the DC-operating point,
so the biasing circuitry needs to be designed accordingly
for optimal fidelity.
Clamped AC-Input Cable Driver
A popular method of further minimizing supply requirements with AC-coupling is to employ a simple clamping
scheme, as shown in Figure 2. In this circuit, the LT6205
operates from 3.3V by having the sync tips control the
charge on the coupling capacitor C1, thereby reducing
the black level input wander to ≈ 0.07V. The only minor
drawback to this circuit is the slight sync tip compression
(≈ 0.025V at input) due to the diode conduction current,
though the picture content remains full fidelity. This circuit
has nearly the design margin of its DC-coupled counterpart, at 0.31V (for this circuit, VMIN = 2.14 + VOH +VOL).
The clamp diode anode bias is selected to set the sync tip
output voltage at or slightly above VOL.
YPbPr to RGB Component Video Converter
The back page application uses the LT6207 quad to implement a minimum amplifier count topology to transcode
consumer component video into RGB. In this circuit, signals
only pass through one active stage from any input to any
output, with passive additions being performed by the
cable back-termination resistors. The compromise in using
passive output addition is that the amplifier outputs must
be twice as large as that of a conventional cable driver. The
Y-channel section also has the demanding requirement that
it single-handedly drives all three outputs to full brightness
during times of white content, so a helper current source
is used to assure unclipped video when operating from
±5V supplies. This circuit maps sync-on-Y to sync on all
the RGB channels, and for best results should have input
black levels at 0V nominal to prevent clipping.
620567fc
13
LT6205/LT6206/LT6207
TYPICAL APPLICATION
3.3V
1k
0.1μF
75Ω
1k
VIDEO OUT
2.4k
4
C1
4.7μF
–
75Ω
5
LT6205
COMPOSITE
VIDEO IN 1VP-P
3
+
1
2
BAT54
10k
IS b 19mA
C2
4.7μF
470Ω
620567 TA02
Figure 2. Clamped AC-Input Video Cable Driver
620567fc
14
LT6205/LT6206/LT6207
PACKAGE DESCRIPTION
S5 Package
5-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1635)
0.62
MAX
0.95
REF
2.90 BSC
(NOTE 4)
1.22 REF
1.4 MIN
3.85 MAX 2.62 REF
2.80 BSC
1.50 – 1.75
(NOTE 4)
PIN ONE
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.30 – 0.45 TYP
5 PLCS (NOTE 3)
0.95 BSC
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
0.30 – 0.50 REF
0.09 – 0.20
(NOTE 3)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
1.90 BSC
S5 TSOT-23 0302
620567fc
15
LT6205/LT6206/LT6207
PACKAGE DESCRIPTION
MS8 Package
8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660)
0.889 ± 0.127
(.035 ± .005)
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
0.65
(.0256)
BSC
0.42 ± 0.038
(.0165 ± .0015)
TYP
8
0.52
(.0205)
REF
7 6 5
RECOMMENDED SOLDER PAD LAYOUT
3.00 ± 0.102
(.118 ± .004)
(NOTE 4)
4.90 ± 0.152
(.193 ± .006)
DETAIL “A”
0.254
(.010)
0° – 6° TYP
GAUGE PLANE
1
0.53 ± 0.152
(.021 ± .006)
2 3
4
1.10
(.043)
MAX
DETAIL “A”
0.86
(.034)
REF
0.18
(.007)
SEATING
PLANE
0.22 – 0.38
(.009 – .015)
TYP
0.1016 ± 0.0508
(.004 ± .002)
0.65
(.0256)
BSC
MSOP (MS8) 0307 REV F
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
GN Package
16-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
.189 – .196*
(4.801 – 4.978)
.045 ±.005
16 15 14 13 12 11 10 9
.254 MIN
.009
(0.229)
REF
.150 – .165
.229 – .244
(5.817 – 6.198)
.0165 ± .0015
.150 – .157**
(3.810 – 3.988)
.0250 BSC
RECOMMENDED SOLDER PAD LAYOUT
1
.015 ± .004
× 45°
(0.38 ± 0.10)
.007 – .0098
(0.178 – 0.249)
.0532 – .0688
(1.35 – 1.75)
2 3
4
5 6
7
8
.004 – .0098
(0.102 – 0.249)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. CONTROLLING DIMENSION: INCHES
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
.008 – .012
(0.203 – 0.305)
TYP
.0250
(0.635)
BSC
GN16 (SSOP) 0204
3. DRAWING NOT TO SCALE
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
620567fc
16
LT6205/LT6206/LT6207
REVISION HISTORY
(Revision history begins at Rev C)
REV
DATE
DESCRIPTION
PAGE NUMBER
C
3/10
C Grade Specified Temperature Range Changed in the Order Information Section
2
620567fc
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
17
LT6205/LT6206/LT6207
TYPICAL APPLICATION
YPBPR to RGB Converter
5V
1μF
36Ω
CMPD6001S
FMMT3906
150Ω
R
4.7k
165Ω
499Ω
4
1
2
–
–
75Ω
150Ω
16
15
499Ω
150Ω
3
Y
+
75Ω
B
107Ω
150Ω
75Ω
LT6207
5
6
365Ω
499Ω
PB
95.3Ω
+
14
+
+
–
–
12
80.6Ω
11
499Ω
10
7
150Ω
13
174Ω
150Ω
G
75Ω
PR
1μF
133Ω
F3dB z 40MHz
IS b 60mA
BLACK LEVELS z 0V
–5V
R = Y + 1.4 • PR
B = Y + 1.8 • PB
G = Y – 0.34 • PB – 0.71 • PR
620567 TA03
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1253/LT1254
Low Cost Dual and Quad Video Amplifiers
–3dB Bandwidth = 90MHz, Current Feedback
LT1395/LT1396/LT1397 Single Dual Quad 400MHz Current Feedback Amplifiers
0.1dB Flatness to 100MHz, 80mA Output Drive
LT1675
RGB Multiplexer with Current Feedback Amplifiers
–3dB Bandwidth = 250MHz, 100MHz Pixel Switching
LT1809/LT1810
Single/Dual, 180MHz, Rail-to-Rail Input and Output Amplifiers 350V/μs Slew Rate, Shutdown, Low Distortion –90dBc at 5MHz
LT6550/LT6551
3.3V Triple and Quad Video Amplifiers
Internal Gain of 2, 110MHz –3dB Bandwidth, Input Common
Modes to Ground
LT6552
3.3V Single Supply Video Difference Amplifier
Differential or Single-Ended Gain Block, 600V/μs Slew Rate,
Input Common Modes to Ground
620567fc
18 Linear Technology Corporation
LT 0310 REV C • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2003